diff options
Diffstat (limited to 'lib/arm_atsam/packs/atmel/SAMD51_DFP/1.0.70/include/component/sercom.h')
| -rw-r--r-- | lib/arm_atsam/packs/atmel/SAMD51_DFP/1.0.70/include/component/sercom.h | 1680 |
1 files changed, 1680 insertions, 0 deletions
diff --git a/lib/arm_atsam/packs/atmel/SAMD51_DFP/1.0.70/include/component/sercom.h b/lib/arm_atsam/packs/atmel/SAMD51_DFP/1.0.70/include/component/sercom.h new file mode 100644 index 0000000000..f884c127a5 --- /dev/null +++ b/lib/arm_atsam/packs/atmel/SAMD51_DFP/1.0.70/include/component/sercom.h @@ -0,0 +1,1680 @@ +/** + * \file + * + * \brief Component description for SERCOM + * + * Copyright (c) 2017 Microchip Technology Inc. + * + * \asf_license_start + * + * \page License + * + * SPDX-License-Identifier: Apache-2.0 + * + * Licensed under the Apache License, Version 2.0 (the "License"); you may + * not use this file except in compliance with the License. + * You may obtain a copy of the Licence at + * + * http://www.apache.org/licenses/LICENSE-2.0 + * + * Unless required by applicable law or agreed to in writing, software + * distributed under the License is distributed on an AS IS BASIS, WITHOUT + * WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. + * See the License for the specific language governing permissions and + * limitations under the License. + * + * \asf_license_stop + * + */ + +#ifndef _SAMD51_SERCOM_COMPONENT_ +#define _SAMD51_SERCOM_COMPONENT_ + +/* ========================================================================== */ +/** SOFTWARE API DEFINITION FOR SERCOM */ +/* ========================================================================== */ +/** \addtogroup SAMD51_SERCOM Serial Communication Interface */ +/*@{*/ + +#define SERCOM_U2201 +#define REV_SERCOM 0x500 + +/* -------- SERCOM_I2CM_CTRLA : (SERCOM Offset: 0x00) (R/W 32) I2CM I2CM Control A -------- */ +#if !(defined(__ASSEMBLY__) || defined(__IAR_SYSTEMS_ASM__)) +typedef union { + struct { + uint32_t SWRST:1; /*!< bit: 0 Software Reset */ + uint32_t ENABLE:1; /*!< bit: 1 Enable */ + uint32_t MODE:3; /*!< bit: 2.. 4 Operating Mode */ + uint32_t :2; /*!< bit: 5.. 6 Reserved */ + uint32_t RUNSTDBY:1; /*!< bit: 7 Run in Standby */ + uint32_t :8; /*!< bit: 8..15 Reserved */ + uint32_t PINOUT:1; /*!< bit: 16 Pin Usage */ + uint32_t :3; /*!< bit: 17..19 Reserved */ + uint32_t SDAHOLD:2; /*!< bit: 20..21 SDA Hold Time */ + uint32_t MEXTTOEN:1; /*!< bit: 22 Master SCL Low Extend Timeout */ + uint32_t SEXTTOEN:1; /*!< bit: 23 Slave SCL Low Extend Timeout */ + uint32_t SPEED:2; /*!< bit: 24..25 Transfer Speed */ + uint32_t :1; /*!< bit: 26 Reserved */ + uint32_t SCLSM:1; /*!< bit: 27 SCL Clock Stretch Mode */ + uint32_t INACTOUT:2; /*!< bit: 28..29 Inactive Time-Out */ + uint32_t LOWTOUTEN:1; /*!< bit: 30 SCL Low Timeout Enable */ + uint32_t :1; /*!< bit: 31 Reserved */ + } bit; /*!< Structure used for bit access */ + uint32_t reg; /*!< Type used for register access */ +} SERCOM_I2CM_CTRLA_Type; +#endif /* !(defined(__ASSEMBLY__) || defined(__IAR_SYSTEMS_ASM__)) */ + +#define SERCOM_I2CM_CTRLA_OFFSET 0x00 /**< \brief (SERCOM_I2CM_CTRLA offset) I2CM Control A */ +#define SERCOM_I2CM_CTRLA_RESETVALUE _U_(0x00000000) /**< \brief (SERCOM_I2CM_CTRLA reset_value) I2CM Control A */ + +#define SERCOM_I2CM_CTRLA_SWRST_Pos 0 /**< \brief (SERCOM_I2CM_CTRLA) Software Reset */ +#define SERCOM_I2CM_CTRLA_SWRST (_U_(0x1) << SERCOM_I2CM_CTRLA_SWRST_Pos) +#define SERCOM_I2CM_CTRLA_ENABLE_Pos 1 /**< \brief (SERCOM_I2CM_CTRLA) Enable */ +#define SERCOM_I2CM_CTRLA_ENABLE (_U_(0x1) << SERCOM_I2CM_CTRLA_ENABLE_Pos) +#define SERCOM_I2CM_CTRLA_MODE_Pos 2 /**< \brief (SERCOM_I2CM_CTRLA) Operating Mode */ +#define SERCOM_I2CM_CTRLA_MODE_Msk (_U_(0x7) << SERCOM_I2CM_CTRLA_MODE_Pos) +#define SERCOM_I2CM_CTRLA_MODE(value) (SERCOM_I2CM_CTRLA_MODE_Msk & ((value) << SERCOM_I2CM_CTRLA_MODE_Pos)) +#define SERCOM_I2CM_CTRLA_RUNSTDBY_Pos 7 /**< \brief (SERCOM_I2CM_CTRLA) Run in Standby */ +#define SERCOM_I2CM_CTRLA_RUNSTDBY (_U_(0x1) << SERCOM_I2CM_CTRLA_RUNSTDBY_Pos) +#define SERCOM_I2CM_CTRLA_PINOUT_Pos 16 /**< \brief (SERCOM_I2CM_CTRLA) Pin Usage */ +#define SERCOM_I2CM_CTRLA_PINOUT (_U_(0x1) << SERCOM_I2CM_CTRLA_PINOUT_Pos) +#define SERCOM_I2CM_CTRLA_SDAHOLD_Pos 20 /**< \brief (SERCOM_I2CM_CTRLA) SDA Hold Time */ +#define SERCOM_I2CM_CTRLA_SDAHOLD_Msk (_U_(0x3) << SERCOM_I2CM_CTRLA_SDAHOLD_Pos) +#define SERCOM_I2CM_CTRLA_SDAHOLD(value) (SERCOM_I2CM_CTRLA_SDAHOLD_Msk & ((value) << SERCOM_I2CM_CTRLA_SDAHOLD_Pos)) +#define SERCOM_I2CM_CTRLA_MEXTTOEN_Pos 22 /**< \brief (SERCOM_I2CM_CTRLA) Master SCL Low Extend Timeout */ +#define SERCOM_I2CM_CTRLA_MEXTTOEN (_U_(0x1) << SERCOM_I2CM_CTRLA_MEXTTOEN_Pos) +#define SERCOM_I2CM_CTRLA_SEXTTOEN_Pos 23 /**< \brief (SERCOM_I2CM_CTRLA) Slave SCL Low Extend Timeout */ +#define SERCOM_I2CM_CTRLA_SEXTTOEN (_U_(0x1) << SERCOM_I2CM_CTRLA_SEXTTOEN_Pos) +#define SERCOM_I2CM_CTRLA_SPEED_Pos 24 /**< \brief (SERCOM_I2CM_CTRLA) Transfer Speed */ +#define SERCOM_I2CM_CTRLA_SPEED_Msk (_U_(0x3) << SERCOM_I2CM_CTRLA_SPEED_Pos) +#define SERCOM_I2CM_CTRLA_SPEED(value) (SERCOM_I2CM_CTRLA_SPEED_Msk & ((value) << SERCOM_I2CM_CTRLA_SPEED_Pos)) +#define SERCOM_I2CM_CTRLA_SCLSM_Pos 27 /**< \brief (SERCOM_I2CM_CTRLA) SCL Clock Stretch Mode */ +#define SERCOM_I2CM_CTRLA_SCLSM (_U_(0x1) << SERCOM_I2CM_CTRLA_SCLSM_Pos) +#define SERCOM_I2CM_CTRLA_INACTOUT_Pos 28 /**< \brief (SERCOM_I2CM_CTRLA) Inactive Time-Out */ +#define SERCOM_I2CM_CTRLA_INACTOUT_Msk (_U_(0x3) << SERCOM_I2CM_CTRLA_INACTOUT_Pos) +#define SERCOM_I2CM_CTRLA_INACTOUT(value) (SERCOM_I2CM_CTRLA_INACTOUT_Msk & ((value) << SERCOM_I2CM_CTRLA_INACTOUT_Pos)) +#define SERCOM_I2CM_CTRLA_LOWTOUTEN_Pos 30 /**< \brief (SERCOM_I2CM_CTRLA) SCL Low Timeout Enable */ +#define SERCOM_I2CM_CTRLA_LOWTOUTEN (_U_(0x1) << SERCOM_I2CM_CTRLA_LOWTOUTEN_Pos) +#define SERCOM_I2CM_CTRLA_MASK _U_(0x7BF1009F) /**< \brief (SERCOM_I2CM_CTRLA) MASK Register */ + +/* -------- SERCOM_I2CS_CTRLA : (SERCOM Offset: 0x00) (R/W 32) I2CS I2CS Control A -------- */ +#if !(defined(__ASSEMBLY__) || defined(__IAR_SYSTEMS_ASM__)) +typedef union { + struct { + uint32_t SWRST:1; /*!< bit: 0 Software Reset */ + uint32_t ENABLE:1; /*!< bit: 1 Enable */ + uint32_t MODE:3; /*!< bit: 2.. 4 Operating Mode */ + uint32_t :2; /*!< bit: 5.. 6 Reserved */ + uint32_t RUNSTDBY:1; /*!< bit: 7 Run during Standby */ + uint32_t :8; /*!< bit: 8..15 Reserved */ + uint32_t PINOUT:1; /*!< bit: 16 Pin Usage */ + uint32_t :3; /*!< bit: 17..19 Reserved */ + uint32_t SDAHOLD:2; /*!< bit: 20..21 SDA Hold Time */ + uint32_t :1; /*!< bit: 22 Reserved */ + uint32_t SEXTTOEN:1; /*!< bit: 23 Slave SCL Low Extend Timeout */ + uint32_t SPEED:2; /*!< bit: 24..25 Transfer Speed */ + uint32_t :1; /*!< bit: 26 Reserved */ + uint32_t SCLSM:1; /*!< bit: 27 SCL Clock Stretch Mode */ + uint32_t :2; /*!< bit: 28..29 Reserved */ + uint32_t LOWTOUTEN:1; /*!< bit: 30 SCL Low Timeout Enable */ + uint32_t :1; /*!< bit: 31 Reserved */ + } bit; /*!< Structure used for bit access */ + uint32_t reg; /*!< Type used for register access */ +} SERCOM_I2CS_CTRLA_Type; +#endif /* !(defined(__ASSEMBLY__) || defined(__IAR_SYSTEMS_ASM__)) */ + +#define SERCOM_I2CS_CTRLA_OFFSET 0x00 /**< \brief (SERCOM_I2CS_CTRLA offset) I2CS Control A */ +#define SERCOM_I2CS_CTRLA_RESETVALUE _U_(0x00000000) /**< \brief (SERCOM_I2CS_CTRLA reset_value) I2CS Control A */ + +#define SERCOM_I2CS_CTRLA_SWRST_Pos 0 /**< \brief (SERCOM_I2CS_CTRLA) Software Reset */ +#define SERCOM_I2CS_CTRLA_SWRST (_U_(0x1) << SERCOM_I2CS_CTRLA_SWRST_Pos) +#define SERCOM_I2CS_CTRLA_ENABLE_Pos 1 /**< \brief (SERCOM_I2CS_CTRLA) Enable */ +#define SERCOM_I2CS_CTRLA_ENABLE (_U_(0x1) << SERCOM_I2CS_CTRLA_ENABLE_Pos) +#define SERCOM_I2CS_CTRLA_MODE_Pos 2 /**< \brief (SERCOM_I2CS_CTRLA) Operating Mode */ +#define SERCOM_I2CS_CTRLA_MODE_Msk (_U_(0x7) << SERCOM_I2CS_CTRLA_MODE_Pos) +#define SERCOM_I2CS_CTRLA_MODE(value) (SERCOM_I2CS_CTRLA_MODE_Msk & ((value) << SERCOM_I2CS_CTRLA_MODE_Pos)) +#define SERCOM_I2CS_CTRLA_RUNSTDBY_Pos 7 /**< \brief (SERCOM_I2CS_CTRLA) Run during Standby */ +#define SERCOM_I2CS_CTRLA_RUNSTDBY (_U_(0x1) << SERCOM_I2CS_CTRLA_RUNSTDBY_Pos) +#define SERCOM_I2CS_CTRLA_PINOUT_Pos 16 /**< \brief (SERCOM_I2CS_CTRLA) Pin Usage */ +#define SERCOM_I2CS_CTRLA_PINOUT (_U_(0x1) << SERCOM_I2CS_CTRLA_PINOUT_Pos) +#define SERCOM_I2CS_CTRLA_SDAHOLD_Pos 20 /**< \brief (SERCOM_I2CS_CTRLA) SDA Hold Time */ +#define SERCOM_I2CS_CTRLA_SDAHOLD_Msk (_U_(0x3) << SERCOM_I2CS_CTRLA_SDAHOLD_Pos) +#define SERCOM_I2CS_CTRLA_SDAHOLD(value) (SERCOM_I2CS_CTRLA_SDAHOLD_Msk & ((value) << SERCOM_I2CS_CTRLA_SDAHOLD_Pos)) +#define SERCOM_I2CS_CTRLA_SEXTTOEN_Pos 23 /**< \brief (SERCOM_I2CS_CTRLA) Slave SCL Low Extend Timeout */ +#define SERCOM_I2CS_CTRLA_SEXTTOEN (_U_(0x1) << SERCOM_I2CS_CTRLA_SEXTTOEN_Pos) +#define SERCOM_I2CS_CTRLA_SPEED_Pos 24 /**< \brief (SERCOM_I2CS_CTRLA) Transfer Speed */ +#define SERCOM_I2CS_CTRLA_SPEED_Msk (_U_(0x3) << SERCOM_I2CS_CTRLA_SPEED_Pos) +#define SERCOM_I2CS_CTRLA_SPEED(value) (SERCOM_I2CS_CTRLA_SPEED_Msk & ((value) << SERCOM_I2CS_CTRLA_SPEED_Pos)) +#define SERCOM_I2CS_CTRLA_SCLSM_Pos 27 /**< \brief (SERCOM_I2CS_CTRLA) SCL Clock Stretch Mode */ +#define SERCOM_I2CS_CTRLA_SCLSM (_U_(0x1) << SERCOM_I2CS_CTRLA_SCLSM_Pos) +#define SERCOM_I2CS_CTRLA_LOWTOUTEN_Pos 30 /**< \brief (SERCOM_I2CS_CTRLA) SCL Low Timeout Enable */ +#define SERCOM_I2CS_CTRLA_LOWTOUTEN (_U_(0x1) << SERCOM_I2CS_CTRLA_LOWTOUTEN_Pos) +#define SERCOM_I2CS_CTRLA_MASK _U_(0x4BB1009F) /**< \brief (SERCOM_I2CS_CTRLA) MASK Register */ + +/* -------- SERCOM_SPI_CTRLA : (SERCOM Offset: 0x00) (R/W 32) SPI SPI Control A -------- */ +#if !(defined(__ASSEMBLY__) || defined(__IAR_SYSTEMS_ASM__)) +typedef union { + struct { + uint32_t SWRST:1; /*!< bit: 0 Software Reset */ + uint32_t ENABLE:1; /*!< bit: 1 Enable */ + uint32_t MODE:3; /*!< bit: 2.. 4 Operating Mode */ + uint32_t :2; /*!< bit: 5.. 6 Reserved */ + uint32_t RUNSTDBY:1; /*!< bit: 7 Run during Standby */ + uint32_t IBON:1; /*!< bit: 8 Immediate Buffer Overflow Notification */ + uint32_t :7; /*!< bit: 9..15 Reserved */ + uint32_t DOPO:2; /*!< bit: 16..17 Data Out Pinout */ + uint32_t :2; /*!< bit: 18..19 Reserved */ + uint32_t DIPO:2; /*!< bit: 20..21 Data In Pinout */ + uint32_t :2; /*!< bit: 22..23 Reserved */ + uint32_t FORM:4; /*!< bit: 24..27 Frame Format */ + uint32_t CPHA:1; /*!< bit: 28 Clock Phase */ + uint32_t CPOL:1; /*!< bit: 29 Clock Polarity */ + uint32_t DORD:1; /*!< bit: 30 Data Order */ + uint32_t :1; /*!< bit: 31 Reserved */ + } bit; /*!< Structure used for bit access */ + uint32_t reg; /*!< Type used for register access */ +} SERCOM_SPI_CTRLA_Type; +#endif /* !(defined(__ASSEMBLY__) || defined(__IAR_SYSTEMS_ASM__)) */ + +#define SERCOM_SPI_CTRLA_OFFSET 0x00 /**< \brief (SERCOM_SPI_CTRLA offset) SPI Control A */ +#define SERCOM_SPI_CTRLA_RESETVALUE _U_(0x00000000) /**< \brief (SERCOM_SPI_CTRLA reset_value) SPI Control A */ + +#define SERCOM_SPI_CTRLA_SWRST_Pos 0 /**< \brief (SERCOM_SPI_CTRLA) Software Reset */ +#define SERCOM_SPI_CTRLA_SWRST (_U_(0x1) << SERCOM_SPI_CTRLA_SWRST_Pos) +#define SERCOM_SPI_CTRLA_ENABLE_Pos 1 /**< \brief (SERCOM_SPI_CTRLA) Enable */ +#define SERCOM_SPI_CTRLA_ENABLE (_U_(0x1) << SERCOM_SPI_CTRLA_ENABLE_Pos) +#define SERCOM_SPI_CTRLA_MODE_Pos 2 /**< \brief (SERCOM_SPI_CTRLA) Operating Mode */ +#define SERCOM_SPI_CTRLA_MODE_Msk (_U_(0x7) << SERCOM_SPI_CTRLA_MODE_Pos) +#define SERCOM_SPI_CTRLA_MODE(value) (SERCOM_SPI_CTRLA_MODE_Msk & ((value) << SERCOM_SPI_CTRLA_MODE_Pos)) +#define SERCOM_SPI_CTRLA_RUNSTDBY_Pos 7 /**< \brief (SERCOM_SPI_CTRLA) Run during Standby */ +#define SERCOM_SPI_CTRLA_RUNSTDBY (_U_(0x1) << SERCOM_SPI_CTRLA_RUNSTDBY_Pos) +#define SERCOM_SPI_CTRLA_IBON_Pos 8 /**< \brief (SERCOM_SPI_CTRLA) Immediate Buffer Overflow Notification */ +#define SERCOM_SPI_CTRLA_IBON (_U_(0x1) << SERCOM_SPI_CTRLA_IBON_Pos) +#define SERCOM_SPI_CTRLA_DOPO_Pos 16 /**< \brief (SERCOM_SPI_CTRLA) Data Out Pinout */ +#define SERCOM_SPI_CTRLA_DOPO_Msk (_U_(0x3) << SERCOM_SPI_CTRLA_DOPO_Pos) +#define SERCOM_SPI_CTRLA_DOPO(value) (SERCOM_SPI_CTRLA_DOPO_Msk & ((value) << SERCOM_SPI_CTRLA_DOPO_Pos)) +#define SERCOM_SPI_CTRLA_DIPO_Pos 20 /**< \brief (SERCOM_SPI_CTRLA) Data In Pinout */ +#define SERCOM_SPI_CTRLA_DIPO_Msk (_U_(0x3) << SERCOM_SPI_CTRLA_DIPO_Pos) +#define SERCOM_SPI_CTRLA_DIPO(value) (SERCOM_SPI_CTRLA_DIPO_Msk & ((value) << SERCOM_SPI_CTRLA_DIPO_Pos)) +#define SERCOM_SPI_CTRLA_FORM_Pos 24 /**< \brief (SERCOM_SPI_CTRLA) Frame Format */ +#define SERCOM_SPI_CTRLA_FORM_Msk (_U_(0xF) << SERCOM_SPI_CTRLA_FORM_Pos) +#define SERCOM_SPI_CTRLA_FORM(value) (SERCOM_SPI_CTRLA_FORM_Msk & ((value) << SERCOM_SPI_CTRLA_FORM_Pos)) +#define SERCOM_SPI_CTRLA_CPHA_Pos 28 /**< \brief (SERCOM_SPI_CTRLA) Clock Phase */ +#define SERCOM_SPI_CTRLA_CPHA (_U_(0x1) << SERCOM_SPI_CTRLA_CPHA_Pos) +#define SERCOM_SPI_CTRLA_CPOL_Pos 29 /**< \brief (SERCOM_SPI_CTRLA) Clock Polarity */ +#define SERCOM_SPI_CTRLA_CPOL (_U_(0x1) << SERCOM_SPI_CTRLA_CPOL_Pos) +#define SERCOM_SPI_CTRLA_DORD_Pos 30 /**< \brief (SERCOM_SPI_CTRLA) Data Order */ +#define SERCOM_SPI_CTRLA_DORD (_U_(0x1) << SERCOM_SPI_CTRLA_DORD_Pos) +#define SERCOM_SPI_CTRLA_MASK _U_(0x7F33019F) /**< \brief (SERCOM_SPI_CTRLA) MASK Register */ + +/* -------- SERCOM_USART_CTRLA : (SERCOM Offset: 0x00) (R/W 32) USART USART Control A -------- */ +#if !(defined(__ASSEMBLY__) || defined(__IAR_SYSTEMS_ASM__)) +typedef union { + struct { + uint32_t SWRST:1; /*!< bit: 0 Software Reset */ + uint32_t ENABLE:1; /*!< bit: 1 Enable */ + uint32_t MODE:3; /*!< bit: 2.. 4 Operating Mode */ + uint32_t :2; /*!< bit: 5.. 6 Reserved */ + uint32_t RUNSTDBY:1; /*!< bit: 7 Run during Standby */ + uint32_t IBON:1; /*!< bit: 8 Immediate Buffer Overflow Notification */ + uint32_t TXINV:1; /*!< bit: 9 Transmit Data Invert */ + uint32_t RXINV:1; /*!< bit: 10 Receive Data Invert */ + uint32_t :2; /*!< bit: 11..12 Reserved */ + uint32_t SAMPR:3; /*!< bit: 13..15 Sample */ + uint32_t TXPO:2; /*!< bit: 16..17 Transmit Data Pinout */ + uint32_t :2; /*!< bit: 18..19 Reserved */ + uint32_t RXPO:2; /*!< bit: 20..21 Receive Data Pinout */ + uint32_t SAMPA:2; /*!< bit: 22..23 Sample Adjustment */ + uint32_t FORM:4; /*!< bit: 24..27 Frame Format */ + uint32_t CMODE:1; /*!< bit: 28 Communication Mode */ + uint32_t CPOL:1; /*!< bit: 29 Clock Polarity */ + uint32_t DORD:1; /*!< bit: 30 Data Order */ + uint32_t :1; /*!< bit: 31 Reserved */ + } bit; /*!< Structure used for bit access */ + uint32_t reg; /*!< Type used for register access */ +} SERCOM_USART_CTRLA_Type; +#endif /* !(defined(__ASSEMBLY__) || defined(__IAR_SYSTEMS_ASM__)) */ + +#define SERCOM_USART_CTRLA_OFFSET 0x00 /**< \brief (SERCOM_USART_CTRLA offset) USART Control A */ +#define SERCOM_USART_CTRLA_RESETVALUE _U_(0x00000000) /**< \brief (SERCOM_USART_CTRLA reset_value) USART Control A */ + +#define SERCOM_USART_CTRLA_SWRST_Pos 0 /**< \brief (SERCOM_USART_CTRLA) Software Reset */ +#define SERCOM_USART_CTRLA_SWRST (_U_(0x1) << SERCOM_USART_CTRLA_SWRST_Pos) +#define SERCOM_USART_CTRLA_ENABLE_Pos 1 /**< \brief (SERCOM_USART_CTRLA) Enable */ +#define SERCOM_USART_CTRLA_ENABLE (_U_(0x1) << SERCOM_USART_CTRLA_ENABLE_Pos) +#define SERCOM_USART_CTRLA_MODE_Pos 2 /**< \brief (SERCOM_USART_CTRLA) Operating Mode */ +#define SERCOM_USART_CTRLA_MODE_Msk (_U_(0x7) << SERCOM_USART_CTRLA_MODE_Pos) +#define SERCOM_USART_CTRLA_MODE(value) (SERCOM_USART_CTRLA_MODE_Msk & ((value) << SERCOM_USART_CTRLA_MODE_Pos)) +#define SERCOM_USART_CTRLA_RUNSTDBY_Pos 7 /**< \brief (SERCOM_USART_CTRLA) Run during Standby */ +#define SERCOM_USART_CTRLA_RUNSTDBY (_U_(0x1) << SERCOM_USART_CTRLA_RUNSTDBY_Pos) +#define SERCOM_USART_CTRLA_IBON_Pos 8 /**< \brief (SERCOM_USART_CTRLA) Immediate Buffer Overflow Notification */ +#define SERCOM_USART_CTRLA_IBON (_U_(0x1) << SERCOM_USART_CTRLA_IBON_Pos) +#define SERCOM_USART_CTRLA_TXINV_Pos 9 /**< \brief (SERCOM_USART_CTRLA) Transmit Data Invert */ +#define SERCOM_USART_CTRLA_TXINV (_U_(0x1) << SERCOM_USART_CTRLA_TXINV_Pos) +#define SERCOM_USART_CTRLA_RXINV_Pos 10 /**< \brief (SERCOM_USART_CTRLA) Receive Data Invert */ +#define SERCOM_USART_CTRLA_RXINV (_U_(0x1) << SERCOM_USART_CTRLA_RXINV_Pos) +#define SERCOM_USART_CTRLA_SAMPR_Pos 13 /**< \brief (SERCOM_USART_CTRLA) Sample */ +#define SERCOM_USART_CTRLA_SAMPR_Msk (_U_(0x7) << SERCOM_USART_CTRLA_SAMPR_Pos) +#define SERCOM_USART_CTRLA_SAMPR(value) (SERCOM_USART_CTRLA_SAMPR_Msk & ((value) << SERCOM_USART_CTRLA_SAMPR_Pos)) +#define SERCOM_USART_CTRLA_TXPO_Pos 16 /**< \brief (SERCOM_USART_CTRLA) Transmit Data Pinout */ +#define SERCOM_USART_CTRLA_TXPO_Msk (_U_(0x3) << SERCOM_USART_CTRLA_TXPO_Pos) +#define SERCOM_USART_CTRLA_TXPO(value) (SERCOM_USART_CTRLA_TXPO_Msk & ((value) << SERCOM_USART_CTRLA_TXPO_Pos)) +#define SERCOM_USART_CTRLA_RXPO_Pos 20 /**< \brief (SERCOM_USART_CTRLA) Receive Data Pinout */ +#define SERCOM_USART_CTRLA_RXPO_Msk (_U_(0x3) << SERCOM_USART_CTRLA_RXPO_Pos) +#define SERCOM_USART_CTRLA_RXPO(value) (SERCOM_USART_CTRLA_RXPO_Msk & ((value) << SERCOM_USART_CTRLA_RXPO_Pos)) +#define SERCOM_USART_CTRLA_SAMPA_Pos 22 /**< \brief (SERCOM_USART_CTRLA) Sample Adjustment */ +#define SERCOM_USART_CTRLA_SAMPA_Msk (_U_(0x3) << SERCOM_USART_CTRLA_SAMPA_Pos) +#define SERCOM_USART_CTRLA_SAMPA(value) (SERCOM_USART_CTRLA_SAMPA_Msk & ((value) << SERCOM_USART_CTRLA_SAMPA_Pos)) +#define SERCOM_USART_CTRLA_FORM_Pos 24 /**< \brief (SERCOM_USART_CTRLA) Frame Format */ +#define SERCOM_USART_CTRLA_FORM_Msk (_U_(0xF) << SERCOM_USART_CTRLA_FORM_Pos) +#define SERCOM_USART_CTRLA_FORM(value) (SERCOM_USART_CTRLA_FORM_Msk & ((value) << SERCOM_USART_CTRLA_FORM_Pos)) +#define SERCOM_USART_CTRLA_CMODE_Pos 28 /**< \brief (SERCOM_USART_CTRLA) Communication Mode */ +#define SERCOM_USART_CTRLA_CMODE (_U_(0x1) << SERCOM_USART_CTRLA_CMODE_Pos) +#define SERCOM_USART_CTRLA_CPOL_Pos 29 /**< \brief (SERCOM_USART_CTRLA) Clock Polarity */ +#define SERCOM_USART_CTRLA_CPOL (_U_(0x1) << SERCOM_USART_CTRLA_CPOL_Pos) +#define SERCOM_USART_CTRLA_DORD_Pos 30 /**< \brief (SERCOM_USART_CTRLA) Data Order */ +#define SERCOM_USART_CTRLA_DORD (_U_(0x1) << SERCOM_USART_CTRLA_DORD_Pos) +#define SERCOM_USART_CTRLA_MASK _U_(0x7FF3E79F) /**< \brief (SERCOM_USART_CTRLA) MASK Register */ + +/* -------- SERCOM_I2CM_CTRLB : (SERCOM Offset: 0x04) (R/W 32) I2CM I2CM Control B -------- */ +#if !(defined(__ASSEMBLY__) || defined(__IAR_SYSTEMS_ASM__)) +typedef union { + struct { + uint32_t :8; /*!< bit: 0.. 7 Reserved */ + uint32_t SMEN:1; /*!< bit: 8 Smart Mode Enable */ + uint32_t QCEN:1; /*!< bit: 9 Quick Command Enable */ + uint32_t :6; /*!< bit: 10..15 Reserved */ + uint32_t CMD:2; /*!< bit: 16..17 Command */ + uint32_t ACKACT:1; /*!< bit: 18 Acknowledge Action */ + uint32_t :13; /*!< bit: 19..31 Reserved */ + } bit; /*!< Structure used for bit access */ + uint32_t reg; /*!< Type used for register access */ +} SERCOM_I2CM_CTRLB_Type; +#endif /* !(defined(__ASSEMBLY__) || defined(__IAR_SYSTEMS_ASM__)) */ + +#define SERCOM_I2CM_CTRLB_OFFSET 0x04 /**< \brief (SERCOM_I2CM_CTRLB offset) I2CM Control B */ +#define SERCOM_I2CM_CTRLB_RESETVALUE _U_(0x00000000) /**< \brief (SERCOM_I2CM_CTRLB reset_value) I2CM Control B */ + +#define SERCOM_I2CM_CTRLB_SMEN_Pos 8 /**< \brief (SERCOM_I2CM_CTRLB) Smart Mode Enable */ +#define SERCOM_I2CM_CTRLB_SMEN (_U_(0x1) << SERCOM_I2CM_CTRLB_SMEN_Pos) +#define SERCOM_I2CM_CTRLB_QCEN_Pos 9 /**< \brief (SERCOM_I2CM_CTRLB) Quick Command Enable */ +#define SERCOM_I2CM_CTRLB_QCEN (_U_(0x1) << SERCOM_I2CM_CTRLB_QCEN_Pos) +#define SERCOM_I2CM_CTRLB_CMD_Pos 16 /**< \brief (SERCOM_I2CM_CTRLB) Command */ +#define SERCOM_I2CM_CTRLB_CMD_Msk (_U_(0x3) << SERCOM_I2CM_CTRLB_CMD_Pos) +#define SERCOM_I2CM_CTRLB_CMD(value) (SERCOM_I2CM_CTRLB_CMD_Msk & ((value) << SERCOM_I2CM_CTRLB_CMD_Pos)) +#define SERCOM_I2CM_CTRLB_ACKACT_Pos 18 /**< \brief (SERCOM_I2CM_CTRLB) Acknowledge Action */ +#define SERCOM_I2CM_CTRLB_ACKACT (_U_(0x1) << SERCOM_I2CM_CTRLB_ACKACT_Pos) +#define SERCOM_I2CM_CTRLB_MASK _U_(0x00070300) /**< \brief (SERCOM_I2CM_CTRLB) MASK Register */ + +/* -------- SERCOM_I2CS_CTRLB : (SERCOM Offset: 0x04) (R/W 32) I2CS I2CS Control B -------- */ +#if !(defined(__ASSEMBLY__) || defined(__IAR_SYSTEMS_ASM__)) +typedef union { + struct { + uint32_t :8; /*!< bit: 0.. 7 Reserved */ + uint32_t SMEN:1; /*!< bit: 8 Smart Mode Enable */ + uint32_t GCMD:1; /*!< bit: 9 PMBus Group Command */ + uint32_t AACKEN:1; /*!< bit: 10 Automatic Address Acknowledge */ + uint32_t :3; /*!< bit: 11..13 Reserved */ + uint32_t AMODE:2; /*!< bit: 14..15 Address Mode */ + uint32_t CMD:2; /*!< bit: 16..17 Command */ + uint32_t ACKACT:1; /*!< bit: 18 Acknowledge Action */ + uint32_t :13; /*!< bit: 19..31 Reserved */ + } bit; /*!< Structure used for bit access */ + uint32_t reg; /*!< Type used for register access */ +} SERCOM_I2CS_CTRLB_Type; +#endif /* !(defined(__ASSEMBLY__) || defined(__IAR_SYSTEMS_ASM__)) */ + +#define SERCOM_I2CS_CTRLB_OFFSET 0x04 /**< \brief (SERCOM_I2CS_CTRLB offset) I2CS Control B */ +#define SERCOM_I2CS_CTRLB_RESETVALUE _U_(0x00000000) /**< \brief (SERCOM_I2CS_CTRLB reset_value) I2CS Control B */ + +#define SERCOM_I2CS_CTRLB_SMEN_Pos 8 /**< \brief (SERCOM_I2CS_CTRLB) Smart Mode Enable */ +#define SERCOM_I2CS_CTRLB_SMEN (_U_(0x1) << SERCOM_I2CS_CTRLB_SMEN_Pos) +#define SERCOM_I2CS_CTRLB_GCMD_Pos 9 /**< \brief (SERCOM_I2CS_CTRLB) PMBus Group Command */ +#define SERCOM_I2CS_CTRLB_GCMD (_U_(0x1) << SERCOM_I2CS_CTRLB_GCMD_Pos) +#define SERCOM_I2CS_CTRLB_AACKEN_Pos 10 /**< \brief (SERCOM_I2CS_CTRLB) Automatic Address Acknowledge */ +#define SERCOM_I2CS_CTRLB_AACKEN (_U_(0x1) << SERCOM_I2CS_CTRLB_AACKEN_Pos) +#define SERCOM_I2CS_CTRLB_AMODE_Pos 14 /**< \brief (SERCOM_I2CS_CTRLB) Address Mode */ +#define SERCOM_I2CS_CTRLB_AMODE_Msk (_U_(0x3) << SERCOM_I2CS_CTRLB_AMODE_Pos) +#define SERCOM_I2CS_CTRLB_AMODE(value) (SERCOM_I2CS_CTRLB_AMODE_Msk & ((value) << SERCOM_I2CS_CTRLB_AMODE_Pos)) +#define SERCOM_I2CS_CTRLB_CMD_Pos 16 /**< \brief (SERCOM_I2CS_CTRLB) Command */ +#define SERCOM_I2CS_CTRLB_CMD_Msk (_U_(0x3) << SERCOM_I2CS_CTRLB_CMD_Pos) +#define SERCOM_I2CS_CTRLB_CMD(value) (SERCOM_I2CS_CTRLB_CMD_Msk & ((value) << SERCOM_I2CS_CTRLB_CMD_Pos)) +#define SERCOM_I2CS_CTRLB_ACKACT_Pos 18 /**< \brief (SERCOM_I2CS_CTRLB) Acknowledge Action */ +#define SERCOM_I2CS_CTRLB_ACKACT (_U_(0x1) << SERCOM_I2CS_CTRLB_ACKACT_Pos) +#define SERCOM_I2CS_CTRLB_MASK _U_(0x0007C700) /**< \brief (SERCOM_I2CS_CTRLB) MASK Register */ + +/* -------- SERCOM_SPI_CTRLB : (SERCOM Offset: 0x04) (R/W 32) SPI SPI Control B -------- */ +#if !(defined(__ASSEMBLY__) || defined(__IAR_SYSTEMS_ASM__)) +typedef union { + struct { + uint32_t CHSIZE:3; /*!< bit: 0.. 2 Character Size */ + uint32_t :3; /*!< bit: 3.. 5 Reserved */ + uint32_t PLOADEN:1; /*!< bit: 6 Data Preload Enable */ + uint32_t :2; /*!< bit: 7.. 8 Reserved */ + uint32_t SSDE:1; /*!< bit: 9 Slave Select Low Detect Enable */ + uint32_t :3; /*!< bit: 10..12 Reserved */ + uint32_t MSSEN:1; /*!< bit: 13 Master Slave Select Enable */ + uint32_t AMODE:2; /*!< bit: 14..15 Address Mode */ + uint32_t :1; /*!< bit: 16 Reserved */ + uint32_t RXEN:1; /*!< bit: 17 Receiver Enable */ + uint32_t :14; /*!< bit: 18..31 Reserved */ + } bit; /*!< Structure used for bit access */ + uint32_t reg; /*!< Type used for register access */ +} SERCOM_SPI_CTRLB_Type; +#endif /* !(defined(__ASSEMBLY__) || defined(__IAR_SYSTEMS_ASM__)) */ + +#define SERCOM_SPI_CTRLB_OFFSET 0x04 /**< \brief (SERCOM_SPI_CTRLB offset) SPI Control B */ +#define SERCOM_SPI_CTRLB_RESETVALUE _U_(0x00000000) /**< \brief (SERCOM_SPI_CTRLB reset_value) SPI Control B */ + +#define SERCOM_SPI_CTRLB_CHSIZE_Pos 0 /**< \brief (SERCOM_SPI_CTRLB) Character Size */ +#define SERCOM_SPI_CTRLB_CHSIZE_Msk (_U_(0x7) << SERCOM_SPI_CTRLB_CHSIZE_Pos) +#define SERCOM_SPI_CTRLB_CHSIZE(value) (SERCOM_SPI_CTRLB_CHSIZE_Msk & ((value) << SERCOM_SPI_CTRLB_CHSIZE_Pos)) +#define SERCOM_SPI_CTRLB_PLOADEN_Pos 6 /**< \brief (SERCOM_SPI_CTRLB) Data Preload Enable */ +#define SERCOM_SPI_CTRLB_PLOADEN (_U_(0x1) << SERCOM_SPI_CTRLB_PLOADEN_Pos) +#define SERCOM_SPI_CTRLB_SSDE_Pos 9 /**< \brief (SERCOM_SPI_CTRLB) Slave Select Low Detect Enable */ +#define SERCOM_SPI_CTRLB_SSDE (_U_(0x1) << SERCOM_SPI_CTRLB_SSDE_Pos) +#define SERCOM_SPI_CTRLB_MSSEN_Pos 13 /**< \brief (SERCOM_SPI_CTRLB) Master Slave Select Enable */ +#define SERCOM_SPI_CTRLB_MSSEN (_U_(0x1) << SERCOM_SPI_CTRLB_MSSEN_Pos) +#define SERCOM_SPI_CTRLB_AMODE_Pos 14 /**< \brief (SERCOM_SPI_CTRLB) Address Mode */ +#define SERCOM_SPI_CTRLB_AMODE_Msk (_U_(0x3) << SERCOM_SPI_CTRLB_AMODE_Pos) +#define SERCOM_SPI_CTRLB_AMODE(value) (SERCOM_SPI_CTRLB_AMODE_Msk & ((value) << SERCOM_SPI_CTRLB_AMODE_Pos)) +#define SERCOM_SPI_CTRLB_RXEN_Pos 17 /**< \brief (SERCOM_SPI_CTRLB) Receiver Enable */ +#define SERCOM_SPI_CTRLB_RXEN (_U_(0x1) << SERCOM_SPI_CTRLB_RXEN_Pos) +#define SERCOM_SPI_CTRLB_MASK _U_(0x0002E247) /**< \brief (SERCOM_SPI_CTRLB) MASK Register */ + +/* -------- SERCOM_USART_CTRLB : (SERCOM Offset: 0x04) (R/W 32) USART USART Control B -------- */ +#if !(defined(__ASSEMBLY__) || defined(__IAR_SYSTEMS_ASM__)) +typedef union { + struct { + uint32_t CHSIZE:3; /*!< bit: 0.. 2 Character Size */ + uint32_t :3; /*!< bit: 3.. 5 Reserved */ + uint32_t SBMODE:1; /*!< bit: 6 Stop Bit Mode */ + uint32_t :1; /*!< bit: 7 Reserved */ + uint32_t COLDEN:1; /*!< bit: 8 Collision Detection Enable */ + uint32_t SFDE:1; /*!< bit: 9 Start of Frame Detection Enable */ + uint32_t ENC:1; /*!< bit: 10 Encoding Format */ + uint32_t :2; /*!< bit: 11..12 Reserved */ + uint32_t PMODE:1; /*!< bit: 13 Parity Mode */ + uint32_t :2; /*!< bit: 14..15 Reserved */ + uint32_t TXEN:1; /*!< bit: 16 Transmitter Enable */ + uint32_t RXEN:1; /*!< bit: 17 Receiver Enable */ + uint32_t :6; /*!< bit: 18..23 Reserved */ + uint32_t LINCMD:2; /*!< bit: 24..25 LIN Command */ + uint32_t :6; /*!< bit: 26..31 Reserved */ + } bit; /*!< Structure used for bit access */ + uint32_t reg; /*!< Type used for register access */ +} SERCOM_USART_CTRLB_Type; +#endif /* !(defined(__ASSEMBLY__) || defined(__IAR_SYSTEMS_ASM__)) */ + +#define SERCOM_USART_CTRLB_OFFSET 0x04 /**< \brief (SERCOM_USART_CTRLB offset) USART Control B */ +#define SERCOM_USART_CTRLB_RESETVALUE _U_(0x00000000) /**< \brief (SERCOM_USART_CTRLB reset_value) USART Control B */ + +#define SERCOM_USART_CTRLB_CHSIZE_Pos 0 /**< \brief (SERCOM_USART_CTRLB) Character Size */ +#define SERCOM_USART_CTRLB_CHSIZE_Msk (_U_(0x7) << SERCOM_USART_CTRLB_CHSIZE_Pos) +#define SERCOM_USART_CTRLB_CHSIZE(value) (SERCOM_USART_CTRLB_CHSIZE_Msk & ((value) << SERCOM_USART_CTRLB_CHSIZE_Pos)) +#define SERCOM_USART_CTRLB_SBMODE_Pos 6 /**< \brief (SERCOM_USART_CTRLB) Stop Bit Mode */ +#define SERCOM_USART_CTRLB_SBMODE (_U_(0x1) << SERCOM_USART_CTRLB_SBMODE_Pos) +#define SERCOM_USART_CTRLB_COLDEN_Pos 8 /**< \brief (SERCOM_USART_CTRLB) Collision Detection Enable */ +#define SERCOM_USART_CTRLB_COLDEN (_U_(0x1) << SERCOM_USART_CTRLB_COLDEN_Pos) +#define SERCOM_USART_CTRLB_SFDE_Pos 9 /**< \brief (SERCOM_USART_CTRLB) Start of Frame Detection Enable */ +#define SERCOM_USART_CTRLB_SFDE (_U_(0x1) << SERCOM_USART_CTRLB_SFDE_Pos) +#define SERCOM_USART_CTRLB_ENC_Pos 10 /**< \brief (SERCOM_USART_CTRLB) Encoding Format */ +#define SERCOM_USART_CTRLB_ENC (_U_(0x1) << SERCOM_USART_CTRLB_ENC_Pos) +#define SERCOM_USART_CTRLB_PMODE_Pos 13 /**< \brief (SERCOM_USART_CTRLB) Parity Mode */ +#define SERCOM_USART_CTRLB_PMODE (_U_(0x1) << SERCOM_USART_CTRLB_PMODE_Pos) +#define SERCOM_USART_CTRLB_TXEN_Pos 16 /**< \brief (SERCOM_USART_CTRLB) Transmitter Enable */ +#define SERCOM_USART_CTRLB_TXEN (_U_(0x1) << SERCOM_USART_CTRLB_TXEN_Pos) +#define SERCOM_USART_CTRLB_RXEN_Pos 17 /**< \brief (SERCOM_USART_CTRLB) Receiver Enable */ +#define SERCOM_USART_CTRLB_RXEN (_U_(0x1) << SERCOM_USART_CTRLB_RXEN_Pos) +#define SERCOM_USART_CTRLB_LINCMD_Pos 24 /**< \brief (SERCOM_USART_CTRLB) LIN Command */ +#define SERCOM_USART_CTRLB_LINCMD_Msk (_U_(0x3) << SERCOM_USART_CTRLB_LINCMD_Pos) +#define SERCOM_USART_CTRLB_LINCMD(value) (SERCOM_USART_CTRLB_LINCMD_Msk & ((value) << SERCOM_USART_CTRLB_LINCMD_Pos)) +#define SERCOM_USART_CTRLB_MASK _U_(0x03032747) /**< \brief (SERCOM_USART_CTRLB) MASK Register */ + +/* -------- SERCOM_I2CM_CTRLC : (SERCOM Offset: 0x08) (R/W 32) I2CM I2CM Control C -------- */ +#if !(defined(__ASSEMBLY__) || defined(__IAR_SYSTEMS_ASM__)) +typedef union { + struct { + uint32_t :24; /*!< bit: 0..23 Reserved */ + uint32_t DATA32B:1; /*!< bit: 24 Data 32 Bit */ + uint32_t :7; /*!< bit: 25..31 Reserved */ + } bit; /*!< Structure used for bit access */ + uint32_t reg; /*!< Type used for register access */ +} SERCOM_I2CM_CTRLC_Type; +#endif /* !(defined(__ASSEMBLY__) || defined(__IAR_SYSTEMS_ASM__)) */ + +#define SERCOM_I2CM_CTRLC_OFFSET 0x08 /**< \brief (SERCOM_I2CM_CTRLC offset) I2CM Control C */ +#define SERCOM_I2CM_CTRLC_RESETVALUE _U_(0x00000000) /**< \brief (SERCOM_I2CM_CTRLC reset_value) I2CM Control C */ + +#define SERCOM_I2CM_CTRLC_DATA32B_Pos 24 /**< \brief (SERCOM_I2CM_CTRLC) Data 32 Bit */ +#define SERCOM_I2CM_CTRLC_DATA32B (_U_(0x1) << SERCOM_I2CM_CTRLC_DATA32B_Pos) +#define SERCOM_I2CM_CTRLC_MASK _U_(0x01000000) /**< \brief (SERCOM_I2CM_CTRLC) MASK Register */ + +/* -------- SERCOM_I2CS_CTRLC : (SERCOM Offset: 0x08) (R/W 32) I2CS I2CS Control C -------- */ +#if !(defined(__ASSEMBLY__) || defined(__IAR_SYSTEMS_ASM__)) +typedef union { + struct { + uint32_t SDASETUP:4; /*!< bit: 0.. 3 SDA Setup Time */ + uint32_t :20; /*!< bit: 4..23 Reserved */ + uint32_t DATA32B:1; /*!< bit: 24 Data 32 Bit */ + uint32_t :7; /*!< bit: 25..31 Reserved */ + } bit; /*!< Structure used for bit access */ + uint32_t reg; /*!< Type used for register access */ +} SERCOM_I2CS_CTRLC_Type; +#endif /* !(defined(__ASSEMBLY__) || defined(__IAR_SYSTEMS_ASM__)) */ + +#define SERCOM_I2CS_CTRLC_OFFSET 0x08 /**< \brief (SERCOM_I2CS_CTRLC offset) I2CS Control C */ +#define SERCOM_I2CS_CTRLC_RESETVALUE _U_(0x00000000) /**< \brief (SERCOM_I2CS_CTRLC reset_value) I2CS Control C */ + +#define SERCOM_I2CS_CTRLC_SDASETUP_Pos 0 /**< \brief (SERCOM_I2CS_CTRLC) SDA Setup Time */ +#define SERCOM_I2CS_CTRLC_SDASETUP_Msk (_U_(0xF) << SERCOM_I2CS_CTRLC_SDASETUP_Pos) +#define SERCOM_I2CS_CTRLC_SDASETUP(value) (SERCOM_I2CS_CTRLC_SDASETUP_Msk & ((value) << SERCOM_I2CS_CTRLC_SDASETUP_Pos)) +#define SERCOM_I2CS_CTRLC_DATA32B_Pos 24 /**< \brief (SERCOM_I2CS_CTRLC) Data 32 Bit */ +#define SERCOM_I2CS_CTRLC_DATA32B (_U_(0x1) << SERCOM_I2CS_CTRLC_DATA32B_Pos) +#define SERCOM_I2CS_CTRLC_MASK _U_(0x0100000F) /**< \brief (SERCOM_I2CS_CTRLC) MASK Register */ + +/* -------- SERCOM_SPI_CTRLC : (SERCOM Offset: 0x08) (R/W 32) SPI SPI Control C -------- */ +#if !(defined(__ASSEMBLY__) || defined(__IAR_SYSTEMS_ASM__)) +typedef union { + struct { + uint32_t ICSPACE:6; /*!< bit: 0.. 5 Inter-Character Spacing */ + uint32_t :18; /*!< bit: 6..23 Reserved */ + uint32_t DATA32B:1; /*!< bit: 24 Data 32 Bit */ + uint32_t :7; /*!< bit: 25..31 Reserved */ + } bit; /*!< Structure used for bit access */ + uint32_t reg; /*!< Type used for register access */ +} SERCOM_SPI_CTRLC_Type; +#endif /* !(defined(__ASSEMBLY__) || defined(__IAR_SYSTEMS_ASM__)) */ + +#define SERCOM_SPI_CTRLC_OFFSET 0x08 /**< \brief (SERCOM_SPI_CTRLC offset) SPI Control C */ +#define SERCOM_SPI_CTRLC_RESETVALUE _U_(0x00000000) /**< \brief (SERCOM_SPI_CTRLC reset_value) SPI Control C */ + +#define SERCOM_SPI_CTRLC_ICSPACE_Pos 0 /**< \brief (SERCOM_SPI_CTRLC) Inter-Character Spacing */ +#define SERCOM_SPI_CTRLC_ICSPACE_Msk (_U_(0x3F) << SERCOM_SPI_CTRLC_ICSPACE_Pos) +#define SERCOM_SPI_CTRLC_ICSPACE(value) (SERCOM_SPI_CTRLC_ICSPACE_Msk & ((value) << SERCOM_SPI_CTRLC_ICSPACE_Pos)) +#define SERCOM_SPI_CTRLC_DATA32B_Pos 24 /**< \brief (SERCOM_SPI_CTRLC) Data 32 Bit */ +#define SERCOM_SPI_CTRLC_DATA32B (_U_(0x1) << SERCOM_SPI_CTRLC_DATA32B_Pos) +#define SERCOM_SPI_CTRLC_MASK _U_(0x0100003F) /**< \brief (SERCOM_SPI_CTRLC) MASK Register */ + +/* -------- SERCOM_USART_CTRLC : (SERCOM Offset: 0x08) (R/W 32) USART USART Control C -------- */ +#if !(defined(__ASSEMBLY__) || defined(__IAR_SYSTEMS_ASM__)) +typedef union { + struct { + uint32_t GTIME:3; /*!< bit: 0.. 2 Guard Time */ + uint32_t :5; /*!< bit: 3.. 7 Reserved */ + uint32_t BRKLEN:2; /*!< bit: 8.. 9 LIN Master Break Length */ + uint32_t HDRDLY:2; /*!< bit: 10..11 LIN Master Header Delay */ + uint32_t :4; /*!< bit: 12..15 Reserved */ + uint32_t INACK:1; /*!< bit: 16 Inhibit Not Acknowledge */ + uint32_t DSNACK:1; /*!< bit: 17 Disable Successive NACK */ + uint32_t :2; /*!< bit: 18..19 Reserved */ + uint32_t MAXITER:3; /*!< bit: 20..22 Maximum Iterations */ + uint32_t :1; /*!< bit: 23 Reserved */ + uint32_t DATA32B:2; /*!< bit: 24..25 Data 32 Bit */ + uint32_t :6; /*!< bit: 26..31 Reserved */ + } bit; /*!< Structure used for bit access */ + uint32_t reg; /*!< Type used for register access */ +} SERCOM_USART_CTRLC_Type; +#endif /* !(defined(__ASSEMBLY__) || defined(__IAR_SYSTEMS_ASM__)) */ + +#define SERCOM_USART_CTRLC_OFFSET 0x08 /**< \brief (SERCOM_USART_CTRLC offset) USART Control C */ +#define SERCOM_USART_CTRLC_RESETVALUE _U_(0x00000000) /**< \brief (SERCOM_USART_CTRLC reset_value) USART Control C */ + +#define SERCOM_USART_CTRLC_GTIME_Pos 0 /**< \brief (SERCOM_USART_CTRLC) Guard Time */ +#define SERCOM_USART_CTRLC_GTIME_Msk (_U_(0x7) << SERCOM_USART_CTRLC_GTIME_Pos) +#define SERCOM_USART_CTRLC_GTIME(value) (SERCOM_USART_CTRLC_GTIME_Msk & ((value) << SERCOM_USART_CTRLC_GTIME_Pos)) +#define SERCOM_USART_CTRLC_BRKLEN_Pos 8 /**< \brief (SERCOM_USART_CTRLC) LIN Master Break Length */ +#define SERCOM_USART_CTRLC_BRKLEN_Msk (_U_(0x3) << SERCOM_USART_CTRLC_BRKLEN_Pos) +#define SERCOM_USART_CTRLC_BRKLEN(value) (SERCOM_USART_CTRLC_BRKLEN_Msk & ((value) << SERCOM_USART_CTRLC_BRKLEN_Pos)) +#define SERCOM_USART_CTRLC_HDRDLY_Pos 10 /**< \brief (SERCOM_USART_CTRLC) LIN Master Header Delay */ +#define SERCOM_USART_CTRLC_HDRDLY_Msk (_U_(0x3) << SERCOM_USART_CTRLC_HDRDLY_Pos) +#define SERCOM_USART_CTRLC_HDRDLY(value) (SERCOM_USART_CTRLC_HDRDLY_Msk & ((value) << SERCOM_USART_CTRLC_HDRDLY_Pos)) +#define SERCOM_USART_CTRLC_INACK_Pos 16 /**< \brief (SERCOM_USART_CTRLC) Inhibit Not Acknowledge */ +#define SERCOM_USART_CTRLC_INACK (_U_(0x1) << SERCOM_USART_CTRLC_INACK_Pos) +#define SERCOM_USART_CTRLC_DSNACK_Pos 17 /**< \brief (SERCOM_USART_CTRLC) Disable Successive NACK */ +#define SERCOM_USART_CTRLC_DSNACK (_U_(0x1) << SERCOM_USART_CTRLC_DSNACK_Pos) +#define SERCOM_USART_CTRLC_MAXITER_Pos 20 /**< \brief (SERCOM_USART_CTRLC) Maximum Iterations */ +#define SERCOM_USART_CTRLC_MAXITER_Msk (_U_(0x7) << SERCOM_USART_CTRLC_MAXITER_Pos) +#define SERCOM_USART_CTRLC_MAXITER(value) (SERCOM_USART_CTRLC_MAXITER_Msk & ((value) << SERCOM_USART_CTRLC_MAXITER_Pos)) +#define SERCOM_USART_CTRLC_DATA32B_Pos 24 /**< \brief (SERCOM_USART_CTRLC) Data 32 Bit */ +#define SERCOM_USART_CTRLC_DATA32B_Msk (_U_(0x3) << SERCOM_USART_CTRLC_DATA32B_Pos) +#define SERCOM_USART_CTRLC_DATA32B(value) (SERCOM_USART_CTRLC_DATA32B_Msk & ((value) << SERCOM_USART_CTRLC_DATA32B_Pos)) +#define SERCOM_USART_CTRLC_MASK _U_(0x03730F07) /**< \brief (SERCOM_USART_CTRLC) MASK Register */ + +/* -------- SERCOM_I2CM_BAUD : (SERCOM Offset: 0x0C) (R/W 32) I2CM I2CM Baud Rate -------- */ +#if !(defined(__ASSEMBLY__) || defined(__IAR_SYSTEMS_ASM__)) +typedef union { + struct { + uint32_t BAUD:8; /*!< bit: 0.. 7 Baud Rate Value */ + uint32_t BAUDLOW:8; /*!< bit: 8..15 Baud Rate Value Low */ + uint32_t HSBAUD:8; /*!< bit: 16..23 High Speed Baud Rate Value */ + uint32_t HSBAUDLOW:8; /*!< bit: 24..31 High Speed Baud Rate Value Low */ + } bit; /*!< Structure used for bit access */ + uint32_t reg; /*!< Type used for register access */ +} SERCOM_I2CM_BAUD_Type; +#endif /* !(defined(__ASSEMBLY__) || defined(__IAR_SYSTEMS_ASM__)) */ + +#define SERCOM_I2CM_BAUD_OFFSET 0x0C /**< \brief (SERCOM_I2CM_BAUD offset) I2CM Baud Rate */ +#define SERCOM_I2CM_BAUD_RESETVALUE _U_(0x00000000) /**< \brief (SERCOM_I2CM_BAUD reset_value) I2CM Baud Rate */ + +#define SERCOM_I2CM_BAUD_BAUD_Pos 0 /**< \brief (SERCOM_I2CM_BAUD) Baud Rate Value */ +#define SERCOM_I2CM_BAUD_BAUD_Msk (_U_(0xFF) << SERCOM_I2CM_BAUD_BAUD_Pos) +#define SERCOM_I2CM_BAUD_BAUD(value) (SERCOM_I2CM_BAUD_BAUD_Msk & ((value) << SERCOM_I2CM_BAUD_BAUD_Pos)) +#define SERCOM_I2CM_BAUD_BAUDLOW_Pos 8 /**< \brief (SERCOM_I2CM_BAUD) Baud Rate Value Low */ +#define SERCOM_I2CM_BAUD_BAUDLOW_Msk (_U_(0xFF) << SERCOM_I2CM_BAUD_BAUDLOW_Pos) +#define SERCOM_I2CM_BAUD_BAUDLOW(value) (SERCOM_I2CM_BAUD_BAUDLOW_Msk & ((value) << SERCOM_I2CM_BAUD_BAUDLOW_Pos)) +#define SERCOM_I2CM_BAUD_HSBAUD_Pos 16 /**< \brief (SERCOM_I2CM_BAUD) High Speed Baud Rate Value */ +#define SERCOM_I2CM_BAUD_HSBAUD_Msk (_U_(0xFF) << SERCOM_I2CM_BAUD_HSBAUD_Pos) +#define SERCOM_I2CM_BAUD_HSBAUD(value) (SERCOM_I2CM_BAUD_HSBAUD_Msk & ((value) << SERCOM_I2CM_BAUD_HSBAUD_Pos)) +#define SERCOM_I2CM_BAUD_HSBAUDLOW_Pos 24 /**< \brief (SERCOM_I2CM_BAUD) High Speed Baud Rate Value Low */ +#define SERCOM_I2CM_BAUD_HSBAUDLOW_Msk (_U_(0xFF) << SERCOM_I2CM_BAUD_HSBAUDLOW_Pos) +#define SERCOM_I2CM_BAUD_HSBAUDLOW(value) (SERCOM_I2CM_BAUD_HSBAUDLOW_Msk & ((value) << SERCOM_I2CM_BAUD_HSBAUDLOW_Pos)) +#define SERCOM_I2CM_BAUD_MASK _U_(0xFFFFFFFF) /**< \brief (SERCOM_I2CM_BAUD) MASK Register */ + +/* -------- SERCOM_SPI_BAUD : (SERCOM Offset: 0x0C) (R/W 8) SPI SPI Baud Rate -------- */ +#if !(defined(__ASSEMBLY__) || defined(__IAR_SYSTEMS_ASM__)) +typedef union { + struct { + uint8_t BAUD:8; |