1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
|
# UART Driver :id=uart-driver
The UART drivers used in QMK have a set of common functions to allow portability between MCUs.
Currently, this driver does not support enabling hardware flow control (the `RTS` and `CTS` pins) if available, but may do so in future.
## AVR Configuration :id=avr-configuration
No special setup is required - just connect the `RX` and `TX` pins of your UART device to the opposite pins on the MCU:
|MCU |`TX`|`RX`|`CTS`|`RTS`|
|-------------|----|----|-----|-----|
|ATmega16/32U2|`D3`|`D2`|`D7` |`D6` |
|ATmega16/32U4|`D3`|`D2`|`D5` |`B7` |
|AT90USB64/128|`D3`|`D2`|*n/a*|*n/a*|
|ATmega32A |`D1`|`D0`|*n/a*|*n/a*|
|ATmega328/P |`D1`|`D0`|*n/a*|*n/a*|
## ChibiOS/ARM Configuration :id=arm-configuration
You'll need to determine which pins can be used for UART -- as an example, STM32 parts generally have multiple UART peripherals, labeled USART1, USART2, USART3 etc.
To enable UART, modify your board's `halconf.h` to enable the serial driver:
```c
#define HAL_USE_SERIAL TRUE
```
Then, modify your board's `mcuconf.h` to enable the peripheral you've chosen, for example:
```c
#undef STM32_SERIAL_USE_USART2
#define STM32_SERIAL_USE_USART2 TRUE
```
Configuration-wise, you'll need to set up the peripheral as per your MCU's datasheet -- the defaults match the pins for a Proton-C, i.e. STM32F303.
|`config.h` override |Description |Default Value|
|--------------------------|---------------------------------------------------------------|-------------|
|`#define SERIAL_DRIVER` |USART peripheral to use - USART1 -> `SD1`, USART2 -> `SD2` etc.|`SD1` |
|`#define SD1_TX_PIN` |The pin to use for TX |`A9` |
|`#define SD1_TX_PAL_MODE` |The alternate function mode for TX |`7` |
|`#define SD1_RX_PIN` |The pin to use for RX |`A10` |
|`#define SD1_RX_PAL_MODE` |The alternate function mode for RX |`7` |
|`#define SD1_CTS_PIN` |The pin to use for CTS |`A11` |
|`#define SD1_CTS_PAL_MODE`|The alternate function mode for CTS |`7` |
|`#define SD1_RTS_PIN` |The pin to use for RTS |`A12` |
|`#define SD1_RTS_PAL_MODE`|The alternate function mode for RTS |`7` |
## API :id=api
### `void uart_init(uint32_t baud)` :id=api-uart-init
Initialize the UART driver. This function must be called only once, before any of the below functions can be called.
#### Arguments :id=api-uart-init-arguments
- `uint32_t baud`
The baud rate to transmit and receive at. This may depend on the device you are communicating with. Common values are 1200, 2400, 4800, 9600, 19200, 38400, 57600, and 115200.
---
### `void uart_write(uint8_t data)` :id=api-uart-write
Transmit a single byte.
#### Arguments :id=api-uart-write-arguments
- `uint8_t data`
The byte to write.
---
### `uint8_t uart_read(void)` :id=api-uart-read
Receive a single byte.
#### Return Value :id=api-uart-read-return
The byte read from the receive buffer. This function will block if the buffer is empty (ie. no data to read).
---
### `void uart_transmit(const uint8_t *data, uint16_t length)` :id=api-uart-transmit
Transmit multiple bytes.
#### Arguments :id=api-uart-transmit-arguments
- `const uint8_t *data`
A pointer to the data to write from.
- `uint16_t length`
The number of bytes to write. Take care not to overrun the length of `data`.
---
### `void uart_receive(char *data, uint16_t length)` :id=api-uart-receive
Receive multiple bytes.
#### Arguments :id=api-uart-receive-arguments
- `uint8_t *data`
A pointer to the buffer to read into.
- `uint16_t length`
The number of bytes to read. Take care not to overrun the length of `data`.
---
### `bool uart_available(void)` :id=api-uart-available
Return whether the receive buffer contains data. Call this function to determine if `uart_read()` will return data immediately.
#### Return Value :id=api-uart-available-return
`true` if the receive buffer length is non-zero.
|
