diff options
Diffstat (limited to 'keyboards')
48 files changed, 1132 insertions, 1250 deletions
diff --git a/keyboards/aeboards/aegis/config.h b/keyboards/aeboards/aegis/config.h index d8c256c7d9..2a35897300 100644 --- a/keyboards/aeboards/aegis/config.h +++ b/keyboards/aeboards/aegis/config.h @@ -47,8 +47,6 @@ /* Locking resynchronize hack */ #define LOCKING_RESYNC_ENABLE -//#define WT_MONO_BACKLIGHT - #define DYNAMIC_KEYMAP_LAYER_COUNT 4 // EEPROM usage diff --git a/keyboards/aeboards/ext65/config.h b/keyboards/aeboards/ext65/config.h index b3e1b8c2f0..7255b463fc 100644 --- a/keyboards/aeboards/ext65/config.h +++ b/keyboards/aeboards/ext65/config.h @@ -47,8 +47,6 @@ /* Locking resynchronize hack */ #define LOCKING_RESYNC_ENABLE -//#define WT_MONO_BACKLIGHT - #define DYNAMIC_KEYMAP_LAYER_COUNT 4 // EEPROM usage diff --git a/keyboards/snagpad/config.h b/keyboards/snagpad/config.h index cd32a3d8c2..a4ab9d5e26 100644 --- a/keyboards/snagpad/config.h +++ b/keyboards/snagpad/config.h @@ -48,9 +48,6 @@ #define RGBLIGHT_VAL_STEP 8 #endif -// Does not use WT_MONO_BACKLIGHT -// #define WT_MONO_BACKLIGHT - #define DYNAMIC_KEYMAP_LAYER_COUNT 4 // EEPROM usage diff --git a/keyboards/wilba_tech/rama_works_koyu/rules.mk b/keyboards/wilba_tech/rama_works_koyu/rules.mk index 9839602247..ebcb6a455f 100644 --- a/keyboards/wilba_tech/rama_works_koyu/rules.mk +++ b/keyboards/wilba_tech/rama_works_koyu/rules.mk @@ -1,5 +1,3 @@ - - # project specific files SRC = keyboards/wilba_tech/wt_main.c \ keyboards/wilba_tech/wt_rgb_backlight.c \ @@ -10,42 +8,14 @@ SRC = keyboards/wilba_tech/wt_main.c \ # MCU name MCU = atmega32u4 -# Processor frequency. -# This will define a symbol, F_CPU, in all source code files equal to the -# processor frequency in Hz. You can then use this symbol in your source code to -# calculate timings. Do NOT tack on a 'UL' at the end, this will be done -# automatically to create a 32-bit value in your source code. -# -# This will be an integer division of F_USB below, as it is sourced by -# F_USB after it has run through any CPU prescalers. Note that this value -# does not *change* the processor frequency - it should merely be updated to -# reflect the processor speed set externally so that the code can use accurate -# software delays. -F_CPU = 16000000 - -# -# LUFA specific -# -# Target architecture (see library "Board Types" documentation). -ARCH = AVR8 - -# Input clock frequency. -# This will define a symbol, F_USB, in all source code files equal to the -# input clock frequency (before any prescaling is performed) in Hz. This value may -# differ from F_CPU if prescaling is used on the latter, and is required as the -# raw input clock is fed directly to the PLL sections of the AVR for high speed -# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' -# at the end, this will be done automatically to create a 32-bit value in your -# source code. -# -# If no clock division is performed on the input clock inside the AVR (via the -# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. -F_USB = $(F_CPU) - -# Interrupt driven control endpoint task(+60) -OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT - -# Boot Section +# Bootloader selection +# Teensy halfkay +# Pro Micro caterina +# Atmel DFU atmel-dfu +# LUFA DFU lufa-dfu +# QMK DFU qmk-dfu +# ATmega32A bootloadHID +# ATmega328P USBasp BOOTLOADER = atmel-dfu # Do not put the microcontroller into power saving mode diff --git a/keyboards/wilba_tech/rama_works_m10_b/config.h b/keyboards/wilba_tech/rama_works_m10_b/config.h index 6901309a08..f72ecae85c 100644 --- a/keyboards/wilba_tech/rama_works_m10_b/config.h +++ b/keyboards/wilba_tech/rama_works_m10_b/config.h @@ -181,8 +181,6 @@ along with this program. If not, see <http://www.gnu.org/licenses/>. /* override number of MIDI tone keycodes (each octave adds 12 keycodes and allocates 12 bytes) */ //#define MIDI_TONE_KEYCODE_OCTAVES 1 -//#define WT_MONO_BACKLIGHT - #define DYNAMIC_KEYMAP_LAYER_COUNT 4 // EEPROM usage diff --git a/keyboards/wilba_tech/rama_works_m10_b/rules.mk b/keyboards/wilba_tech/rama_works_m10_b/rules.mk index 70258b9ead..99330021f2 100644 --- a/keyboards/wilba_tech/rama_works_m10_b/rules.mk +++ b/keyboards/wilba_tech/rama_works_m10_b/rules.mk @@ -4,44 +4,14 @@ SRC = keyboards/wilba_tech/wt_main.c # MCU name MCU = atmega32u4 -# Processor frequency. -# This will define a symbol, F_CPU, in all source code files equal to the -# processor frequency in Hz. You can then use this symbol in your source code to -# calculate timings. Do NOT tack on a 'UL' at the end, this will be done -# automatically to create a 32-bit value in your source code. -# -# This will be an integer division of F_USB below, as it is sourced by -# F_USB after it has run through any CPU prescalers. Note that this value -# does not *change* the processor frequency - it should merely be updated to -# reflect the processor speed set externally so that the code can use accurate -# software delays. -F_CPU = 16000000 - - -# -# LUFA specific -# -# Target architecture (see library "Board Types" documentation). -ARCH = AVR8 - -# Input clock frequency. -# This will define a symbol, F_USB, in all source code files equal to the -# input clock frequency (before any prescaling is performed) in Hz. This value may -# differ from F_CPU if prescaling is used on the latter, and is required as the -# raw input clock is fed directly to the PLL sections of the AVR for high speed -# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' -# at the end, this will be done automatically to create a 32-bit value in your -# source code. -# -# If no clock division is performed on the input clock inside the AVR (via the -# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. -F_USB = $(F_CPU) - -# Interrupt driven control endpoint task(+60) -OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT - - -# Boot Section +# Bootloader selection +# Teensy halfkay +# Pro Micro caterina +# Atmel DFU atmel-dfu +# LUFA DFU lufa-dfu +# QMK DFU qmk-dfu +# ATmega32A bootloadHID +# ATmega328P USBasp BOOTLOADER = atmel-dfu diff --git a/keyboards/wilba_tech/rama_works_m60_a/rules.mk b/keyboards/wilba_tech/rama_works_m60_a/rules.mk index 3b2287333c..4ce5dc54cb 100644 --- a/keyboards/wilba_tech/rama_works_m60_a/rules.mk +++ b/keyboards/wilba_tech/rama_works_m60_a/rules.mk @@ -10,42 +10,14 @@ SRC = keyboards/wilba_tech/wt_main.c \ # MCU name MCU = atmega32u4 -# Processor frequency. -# This will define a symbol, F_CPU, in all source code files equal to the -# processor frequency in Hz. You can then use this symbol in your source code to -# calculate timings. Do NOT tack on a 'UL' at the end, this will be done -# automatically to create a 32-bit value in your source code. -# -# This will be an integer division of F_USB below, as it is sourced by -# F_USB after it has run through any CPU prescalers. Note that this value -# does not *change* the processor frequency - it should merely be updated to -# reflect the processor speed set externally so that the code can use accurate -# software delays. -F_CPU = 16000000 - -# -# LUFA specific -# -# Target architecture (see library "Board Types" documentation). -ARCH = AVR8 - -# Input clock frequency. -# This will define a symbol, F_USB, in all source code files equal to the -# input clock frequency (before any prescaling is performed) in Hz. This value may -# differ from F_CPU if prescaling is used on the latter, and is required as the -# raw input clock is fed directly to the PLL sections of the AVR for high speed -# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' -# at the end, this will be done automatically to create a 32-bit value in your -# source code. -# -# If no clock division is performed on the input clock inside the AVR (via the -# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. -F_USB = $(F_CPU) - -# Interrupt driven control endpoint task(+60) -OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT - -# Boot Section +# Bootloader selection +# Teensy halfkay +# Pro Micro caterina +# Atmel DFU atmel-dfu +# LUFA DFU lufa-dfu +# QMK DFU qmk-dfu +# ATmega32A bootloadHID +# ATmega328P USBasp BOOTLOADER = atmel-dfu # Do not put the microcontroller into power saving mode diff --git a/keyboards/wilba_tech/rama_works_m6_a/rules.mk b/keyboards/wilba_tech/rama_works_m6_a/rules.mk index 4270e7090c..32f0e25de8 100644 --- a/keyboards/wilba_tech/rama_works_m6_a/rules.mk +++ b/keyboards/wilba_tech/rama_works_m6_a/rules.mk @@ -4,43 +4,14 @@ SRC = keyboards/wilba_tech/wt_main.c # MCU name MCU = atmega32u4 -# Processor frequency. -# This will define a symbol, F_CPU, in all source code files equal to the -# processor frequency in Hz. You can then use this symbol in your source code to -# calculate timings. Do NOT tack on a 'UL' at the end, this will be done -# automatically to create a 32-bit value in your source code. -# -# This will be an integer division of F_USB below, as it is sourced by -# F_USB after it has run through any CPU prescalers. Note that this value -# does not *change* the processor frequency - it should merely be updated to -# reflect the processor speed set externally so that the code can use accurate -# software delays. -F_CPU = 16000000 - - -# -# LUFA specific -# -# Target architecture (see library "Board Types" documentation). -ARCH = AVR8 - -# Input clock frequency. -# This will define a symbol, F_USB, in all source code files equal to the -# input clock frequency (before any prescaling is performed) in Hz. This value may -# differ from F_CPU if prescaling is used on the latter, and is required as the -# raw input clock is fed directly to the PLL sections of the AVR for high speed -# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' -# at the end, this will be done automatically to create a 32-bit value in your -# source code. -# -# If no clock division is performed on the input clock inside the AVR (via the -# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. -F_USB = $(F_CPU) - -# Interrupt driven control endpoint task(+60) -OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT - -# Boot Section +# Bootloader selection +# Teensy halfkay +# Pro Micro caterina +# Atmel DFU atmel-dfu +# LUFA DFU lufa-dfu +# QMK DFU qmk-dfu +# ATmega32A bootloadHID +# ATmega328P USBasp BOOTLOADER = atmel-dfu # Do not put the microcontroller into power saving mode diff --git a/keyboards/wilba_tech/rama_works_m6_b/rules.mk b/keyboards/wilba_tech/rama_works_m6_b/rules.mk index 6b7b3a63d8..c016fa344f 100644 --- a/keyboards/wilba_tech/rama_works_m6_b/rules.mk +++ b/keyboards/wilba_tech/rama_works_m6_b/rules.mk @@ -5,47 +5,17 @@ SRC = keyboards/wilba_tech/wt_main.c \ drivers/issi/is31fl3218.c \ drivers/avr/i2c_master.c - # MCU name MCU = atmega32u4 -# Processor frequency. -# This will define a symbol, F_CPU, in all source code files equal to the -# processor frequency in Hz. You can then use this symbol in your source code to -# calculate timings. Do NOT tack on a 'UL' at the end, this will be done -# automatically to create a 32-bit value in your source code. -# -# This will be an integer division of F_USB below, as it is sourced by -# F_USB after it has run through any CPU prescalers. Note that this value -# does not *change* the processor frequency - it should merely be updated to -# reflect the processor speed set externally so that the code can use accurate -# software delays. -F_CPU = 16000000 - - -# -# LUFA specific -# -# Target architecture (see library "Board Types" documentation). -ARCH = AVR8 - -# Input clock frequency. -# This will define a symbol, F_USB, in all source code files equal to the -# input clock frequency (before any prescaling is performed) in Hz. This value may -# differ from F_CPU if prescaling is used on the latter, and is required as the -# raw input clock is fed directly to the PLL sections of the AVR for high speed -# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' -# at the end, this will be done automatically to create a 32-bit value in your -# source code. -# -# If no clock division is performed on the input clock inside the AVR (via the -# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. -F_USB = $(F_CPU) - -# Interrupt driven control endpoint task(+60) -OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT - -# Boot Section +# Bootloader selection +# Teensy halfkay +# Pro Micro caterina +# Atmel DFU atmel-dfu +# LUFA DFU lufa-dfu +# QMK DFU qmk-dfu +# ATmega32A bootloadHID +# ATmega328P USBasp BOOTLOADER = atmel-dfu # Do not put the microcontroller into power saving mode diff --git a/keyboards/wilba_tech/rama_works_u80_a/config.h b/keyboards/wilba_tech/rama_works_u80_a/config.h index 348b124b90..d0bf0ed1e3 100644 --- a/keyboards/wilba_tech/rama_works_u80_a/config.h +++ b/keyboards/wilba_tech/rama_works_u80_a/config.h @@ -179,8 +179,6 @@ /* override number of MIDI tone keycodes (each octave adds 12 keycodes and allocates 12 bytes) */ //#define MIDI_TONE_KEYCODE_OCTAVES 1 -//#define WT_MONO_BACKLIGHT - // IS31FL3731 driver #define DRIVER_COUNT 3 #define DRIVER_LED_TOTAL 108 diff --git a/keyboards/wilba_tech/rama_works_u80_a/rules.mk b/keyboards/wilba_tech/rama_works_u80_a/rules.mk index 6079ad8932..caecaecbb7 100644 --- a/keyboards/wilba_tech/rama_works_u80_a/rules.mk +++ b/keyboards/wilba_tech/rama_works_u80_a/rules.mk @@ -8,44 +8,14 @@ SRC = keyboards/wilba_tech/wt_main.c \ # MCU name MCU = atmega32u4 -# Processor frequency. -# This will define a symbol, F_CPU, in all source code files equal to the -# processor frequency in Hz. You can then use this symbol in your source code to -# calculate timings. Do NOT tack on a 'UL' at the end, this will be done -# automatically to create a 32-bit value in your source code. -# -# This will be an integer division of F_USB below, as it is sourced by -# F_USB after it has run through any CPU prescalers. Note that this value -# does not *change* the processor frequency - it should merely be updated to -# reflect the processor speed set externally so that the code can use accurate -# software delays. -F_CPU = 16000000 - - -# -# LUFA specific -# -# Target architecture (see library "Board Types" documentation). -ARCH = AVR8 - -# Input clock frequency. -# This will define a symbol, F_USB, in all source code files equal to the -# input clock frequency (before any prescaling is performed) in Hz. This value may -# differ from F_CPU if prescaling is used on the latter, and is required as the -# raw input clock is fed directly to the PLL sections of the AVR for high speed -# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' -# at the end, this will be done automatically to create a 32-bit value in your -# source code. -# -# If no clock division is performed on the input clock inside the AVR (via the -# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. -F_USB = $(F_CPU) - -# Interrupt driven control endpoint task(+60) -OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT - - -# Boot Section +# Bootloader selection +# Teensy halfkay +# Pro Micro caterina +# Atmel DFU atmel-dfu +# LUFA DFU lufa-dfu +# QMK DFU qmk-dfu +# ATmega32A bootloadHID +# ATmega328P USBasp BOOTLOADER = atmel-dfu diff --git a/keyboards/wilba_tech/wt60_a/config.h b/keyboards/wilba_tech/wt60_a/config.h index 3ac8ea6fc0..6e1e0e81cc 100644 --- a/keyboards/wilba_tech/wt60_a/config.h +++ b/keyboards/wilba_tech/wt60_a/config.h @@ -179,14 +179,33 @@ /* override number of MIDI tone keycodes (each octave adds 12 keycodes and allocates 12 bytes) */ //#define MIDI_TONE_KEYCODE_OCTAVES 1 -#define WT_MONO_BACKLIGHT +// enable the mono backlight +#define MONO_BACKLIGHT_ENABLED 1 + +// enable the RGB indicator for WT75-A +#define MONO_BACKLIGHT_WT75_A + +// disable backlight when USB suspended (PC sleep/hibernate/shutdown) +#define MONO_BACKLIGHT_DISABLE_WHEN_USB_SUSPENDED 0 + +// disable backlight after timeout in minutes, 0 = no timeout +#define MONO_BACKLIGHT_DISABLE_AFTER_TIMEOUT 0 + +// the default brightness +#define MONO_BACKLIGHT_BRIGHTNESS 255 + +// the default effect +#define MONO_BACKLIGHT_EFFECT 1 + +// the default effect speed (0-3) +#define MONO_BACKLIGHT_EFFECT_SPEED 0 #define DYNAMIC_KEYMAP_LAYER_COUNT 4 // EEPROM usage // TODO: refactor with new user EEPROM code (coming soon) -#define EEPROM_MAGIC 0x451F +#define EEPROM_MAGIC 0x4520 #define EEPROM_MAGIC_ADDR 34 // Bump this every time we change what we store // This will automatically reset the EEPROM with defaults @@ -194,9 +213,11 @@ #define EEPROM_VERSION 0x08 #define EEPROM_VERSION_ADDR 36 -// Dynamic keymap starts after EEPROM version -#define DYNAMIC_KEYMAP_EEPROM_ADDR 37 -// Dynamic macro starts after dynamic keymaps (37+(4*5*14*2)) = (37+560) -#define DYNAMIC_KEYMAP_MACRO_EEPROM_ADDR 597 -#define DYNAMIC_KEYMAP_MACRO_EEPROM_SIZE 427 +// Backlight config starts after EEPROM version +#define MONO_BACKLIGHT_CONFIG_EEPROM_ADDR 37 +// Dynamic keymap starts after backlight config (37+7) +#define DYNAMIC_KEYMAP_EEPROM_ADDR 44 +// Dynamic macro starts after dynamic keymaps (44+(4*5*14*2)) = (44+560) +#define DYNAMIC_KEYMAP_MACRO_EEPROM_ADDR 604 +#define DYNAMIC_KEYMAP_MACRO_EEPROM_SIZE 420 #define DYNAMIC_KEYMAP_MACRO_COUNT 16 diff --git a/keyboards/wilba_tech/wt60_a/keymaps/via/rules.mk b/keyboards/wilba_tech/wt60_a/keymaps/via/rules.mk index 76a07d7a44..8834bf0c8e 100644 --- a/keyboards/wilba_tech/wt60_a/keymaps/via/rules.mk +++ b/keyboards/wilba_tech/wt60_a/keymaps/via/rules.mk @@ -1,71 +1,2 @@ -# project specific files -SRC = drivers/issi/is31fl3736.c \ - drivers/avr/i2c_master.c \ - keyboards/wilba_tech/wt_mono_backlight.c \ - keyboards/wilba_tech/wt_main.c - -# MCU name -MCU = atmega32u4 - -# Processor frequency. -# This will define a symbol, F_CPU, in all source code files equal to the -# processor frequency in Hz. You can then use this symbol in your source code to -# calculate timings. Do NOT tack on a 'UL' at the end, this will be done -# automatically to create a 32-bit value in your source code. -# -# This will be an integer division of F_USB below, as it is sourced by -# F_USB after it has run through any CPU prescalers. Note that this value -# does not *change* the processor frequency - it should merely be updated to -# reflect the processor speed set externally so that the code can use accurate -# software delays. -F_CPU = 16000000 - - -# -# LUFA specific -# -# Target architecture (see library "Board Types" documentation). -ARCH = AVR8 - -# Input clock frequency. -# This will define a symbol, F_USB, in all source code files equal to the -# input clock frequency (before any prescaling is performed) in Hz. This value may -# differ from F_CPU if prescaling is used on the latter, and is required as the -# raw input clock is fed directly to the PLL sections of the AVR for high speed -# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' -# at the end, this will be done automatically to create a 32-bit value in your -# source code. -# -# If no clock division is performed on the input clock inside the AVR (via the -# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. -F_USB = $(F_CPU) - -# Interrupt driven control endpoint task(+60) -OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT - - -# Boot Section -BOOTLOADER = atmel-dfu - - -# Build Options -# change yes to no to disable -# -BOOTMAGIC_ENABLE = no # Virtual DIP switch configuration(+1000) -MOUSEKEY_ENABLE = no # Mouse keys(+4700) -EXTRAKEY_ENABLE = yes # Audio control and System control(+450) -CONSOLE_ENABLE = no # Console for debug(+400) -COMMAND_ENABLE = no # Commands for debug and configuration -# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE -SLEEP_LED_ENABLE = no # Breathing sleep LED during USB suspend -# if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work -NKRO_ENABLE = yes # USB Nkey Rollover -BACKLIGHT_ENABLE = no # Enable keyboard backlight functionality on B7 by default -MIDI_ENABLE = no # MIDI support (+2400 to 4200, depending on config) -UNICODE_ENABLE = no # Unicode -BLUETOOTH_ENABLE = no # Enable Bluetooth with the Adafruit EZ-Key HID -AUDIO_ENABLE = no # Audio output on port C6 -FAUXCLICKY_ENABLE = no # Use buzzer to emulate clicky switches - RAW_ENABLE = yes DYNAMIC_KEYMAP_ENABLE = yes
\ No newline at end of file diff --git a/keyboards/wilba_tech/wt60_a/rules.mk b/keyboards/wilba_tech/wt60_a/rules.mk index e41f2186b3..4f702fab49 100644 --- a/keyboards/wilba_tech/wt60_a/rules.mk +++ b/keyboards/wilba_tech/wt60_a/rules.mk @@ -1,6 +1,7 @@ # project specific files SRC = drivers/issi/is31fl3736.c \ drivers/avr/i2c_master.c \ + quantum/color.c \ keyboards/wilba_tech/wt_mono_backlight.c \ keyboards/wilba_tech/wt_main.c diff --git a/keyboards/wilba_tech/wt60_d/keymaps/via/rules.mk b/keyboards/wilba_tech/wt60_d/keymaps/via/rules.mk index f072c67198..8834bf0c8e 100644 --- a/keyboards/wilba_tech/wt60_d/keymaps/via/rules.mk +++ b/keyboards/wilba_tech/wt60_d/keymaps/via/rules.mk @@ -1,68 +1,2 @@ -# project specific files -SRC = keyboards/wilba_tech/wt_main.c - -# MCU name -MCU = atmega32u4 - -# Processor frequency. -# This will define a symbol, F_CPU, in all source code files equal to the -# processor frequency in Hz. You can then use this symbol in your source code to -# calculate timings. Do NOT tack on a 'UL' at the end, this will be done -# automatically to create a 32-bit value in your source code. -# -# This will be an integer division of F_USB below, as it is sourced by -# F_USB after it has run through any CPU prescalers. Note that this value -# does not *change* the processor frequency - it should merely be updated to -# reflect the processor speed set externally so that the code can use accurate -# software delays. -F_CPU = 16000000 - - -# -# LUFA specific -# -# Target architecture (see library "Board Types" documentation). -ARCH = AVR8 - -# Input clock frequency. -# This will define a symbol, F_USB, in all source code files equal to the -# input clock frequency (before any prescaling is performed) in Hz. This value may -# differ from F_CPU if prescaling is used on the latter, and is required as the -# raw input clock is fed directly to the PLL sections of the AVR for high speed -# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' -# at the end, this will be done automatically to create a 32-bit value in your -# source code. -# -# If no clock division is performed on the input clock inside the AVR (via the -# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. -F_USB = $(F_CPU) - -# Interrupt driven control endpoint t |