summaryrefslogtreecommitdiffstats
path: root/keyboards/rgbkb/sol/rules.mk
diff options
context:
space:
mode:
Diffstat (limited to 'keyboards/rgbkb/sol/rules.mk')
-rw-r--r--keyboards/rgbkb/sol/rules.mk42
1 files changed, 1 insertions, 41 deletions
diff --git a/keyboards/rgbkb/sol/rules.mk b/keyboards/rgbkb/sol/rules.mk
index a3dcfc2903..3be8f0b229 100644
--- a/keyboards/rgbkb/sol/rules.mk
+++ b/keyboards/rgbkb/sol/rules.mk
@@ -2,41 +2,15 @@
MCU = atmega32u4
# Processor frequency.
-# This will define a symbol, F_CPU, in all source code files equal to the
-# processor frequency in Hz. You can then use this symbol in your source code to
-# calculate timings. Do NOT tack on a 'UL' at the end, this will be done
-# automatically to create a 32-bit value in your source code.
-#
-# This will be an integer division of F_USB below, as it is sourced by
-# F_USB after it has run through any CPU prescalers. Note that this value
-# does not *change* the processor frequency - it should merely be updated to
-# reflect the processor speed set externally so that the code can use accurate
-# software delays.
F_CPU = 16000000
-#
-# LUFA specific
-#
# Target architecture (see library "Board Types" documentation).
ARCH = AVR8
# Input clock frequency.
-# This will define a symbol, F_USB, in all source code files equal to the
-# input clock frequency (before any prescaling is performed) in Hz. This value may
-# differ from F_CPU if prescaling is used on the latter, and is required as the
-# raw input clock is fed directly to the PLL sections of the AVR for high speed
-# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
-# at the end, this will be done automatically to create a 32-bit value in your
-# source code.
-#
-# If no clock division is performed on the input clock inside the AVR (via the
-# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
F_USB = $(F_CPU)
# Bootloader
-# This definition is optional, and if your keyboard supports multiple bootloaders of
-# different sizes, comment this out, and the correct address will be loaded
-# automatically (+60). See bootloader.mk for all options.
BOOTLOADER = qmk-dfu
# Interrupt driven control endpoint task(+60)
@@ -48,18 +22,4 @@ OPT_DEFS += -DOLED_FONT_H=\"common/glcdfont.c\"
SPLIT_KEYBOARD = yes
ENCODER_ENABLE = yes
-# Build Options
-# change to "no" to disable the options, or define them in the Makefile in
-# the appropriate keymap folder that will get included automatically
-#
-BOOTMAGIC_ENABLE = no # Virtual DIP switch configuration(+1000)
-MOUSEKEY_ENABLE = yes # Mouse keys(+4700)
-EXTRAKEY_ENABLE = yes # Audio control and System control(+450)
-CONSOLE_ENABLE = no # Console for debug(+400)
-COMMAND_ENABLE = yes # Commands for debug and configuration
-NKRO_ENABLE = no # Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
-UNICODE_ENABLE = no # Unicode
-BLUETOOTH_ENABLE = no # Enable Bluetooth with the Adafruit EZ-Key HID
-RGBLIGHT_ENABLE = yes # Enable WS2812 RGB underlight. Do not enable this with audio at the same time.
-
-DEFAULT_FOLDER = rgbkb/sol/rev1
+DEFAULT_FOLDER = rgbkb/sol/rev2