summaryrefslogtreecommitdiffstats
path: root/keyboards/ploopyco/pmw3360.h
diff options
context:
space:
mode:
Diffstat (limited to 'keyboards/ploopyco/pmw3360.h')
-rw-r--r--keyboards/ploopyco/pmw3360.h103
1 files changed, 0 insertions, 103 deletions
diff --git a/keyboards/ploopyco/pmw3360.h b/keyboards/ploopyco/pmw3360.h
deleted file mode 100644
index c1d5e3badb..0000000000
--- a/keyboards/ploopyco/pmw3360.h
+++ /dev/null
@@ -1,103 +0,0 @@
-/* Copyright 2020 Christopher Courtney, aka Drashna Jael're (@drashna) <drashna@live.com>
- * Copyright 2019 Sunjun Kim
- * Copyright 2020 Ploopy Corporation
- *
- * This program is free software: you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation, either version 2 of the License, or
- * (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program. If not, see <http://www.gnu.org/licenses/>.
- */
-
-#pragma once
-
-#include "spi_master.h"
-
-// Registers
-#define REG_Product_ID 0x00
-#define REG_Revision_ID 0x01
-#define REG_Motion 0x02
-#define REG_Delta_X_L 0x03
-#define REG_Delta_X_H 0x04
-#define REG_Delta_Y_L 0x05
-#define REG_Delta_Y_H 0x06
-#define REG_SQUAL 0x07
-#define REG_Raw_Data_Sum 0x08
-#define REG_Maximum_Raw_data 0x09
-#define REG_Minimum_Raw_data 0x0A
-#define REG_Shutter_Lower 0x0B
-#define REG_Shutter_Upper 0x0C
-#define REG_Control 0x0D
-#define REG_Config1 0x0F
-#define REG_Config2 0x10
-#define REG_Angle_Tune 0x11
-#define REG_Frame_Capture 0x12
-#define REG_SROM_Enable 0x13
-#define REG_Run_Downshift 0x14
-#define REG_Rest1_Rate_Lower 0x15
-#define REG_Rest1_Rate_Upper 0x16
-#define REG_Rest1_Downshift 0x17
-#define REG_Rest2_Rate_Lower 0x18
-#define REG_Rest2_Rate_Upper 0x19
-#define REG_Rest2_Downshift 0x1A
-#define REG_Rest3_Rate_Lower 0x1B
-#define REG_Rest3_Rate_Upper 0x1C
-#define REG_Observation 0x24
-#define REG_Data_Out_Lower 0x25
-#define REG_Data_Out_Upper 0x26
-#define REG_Raw_Data_Dump 0x29
-#define REG_SROM_ID 0x2A
-#define REG_Min_SQ_Run 0x2B
-#define REG_Raw_Data_Threshold 0x2C
-#define REG_Config5 0x2F
-#define REG_Power_Up_Reset 0x3A
-#define REG_Shutdown 0x3B
-#define REG_Inverse_Product_ID 0x3F
-#define REG_LiftCutoff_Tune3 0x41
-#define REG_Angle_Snap 0x42
-#define REG_LiftCutoff_Tune1 0x4A
-#define REG_Motion_Burst 0x50
-#define REG_LiftCutoff_Tune_Timeout 0x58
-#define REG_LiftCutoff_Tune_Min_Length 0x5A
-#define REG_SROM_Load_Burst 0x62
-#define REG_Lift_Config 0x63
-#define REG_Raw_Data_Burst 0x64
-#define REG_LiftCutoff_Tune2 0x65
-
-#ifdef CONSOLE_ENABLE
-void print_byte(uint8_t byte);
-#endif
-
-typedef struct {
- int8_t motion;
- bool isMotion; // True if a motion is detected.
- bool isOnSurface; // True when a chip is on a surface
- int16_t dx; // displacement on x directions. Unit: Count. (CPI * Count = Inch value)
- int8_t mdx;
- int16_t dy; // displacement on y directions.
- int8_t mdy;
-} report_pmw_t;
-
-
-
-bool spi_start_adv(void);
-void spi_stop_adv(void);
-spi_status_t spi_write_adv(uint8_t reg_addr, uint8_t data);
-uint8_t spi_read_adv(uint8_t reg_addr);
-bool pmw_spi_init(void);
-void pmw_set_cpi(uint16_t cpi);
-void pmw_upload_firmware(void);
-bool pmw_check_signature(void);
-report_pmw_t pmw_read_burst(void);
-
-
-#define degToRad(angleInDegrees) ((angleInDegrees)*M_PI / 180.0)
-#define radToDeg(angleInRadians) ((angleInRadians)*180.0 / M_PI)
-#define constrain(amt, low, high) ((amt) < (low) ? (low) : ((amt) > (high) ? (high) : (amt)))