summaryrefslogtreecommitdiffstats
path: root/keyboards/planck/keymaps/vaire
diff options
context:
space:
mode:
Diffstat (limited to 'keyboards/planck/keymaps/vaire')
-rw-r--r--keyboards/planck/keymaps/vaire/config.h6
-rw-r--r--keyboards/planck/keymaps/vaire/rules.mk84
2 files changed, 4 insertions, 86 deletions
diff --git a/keyboards/planck/keymaps/vaire/config.h b/keyboards/planck/keymaps/vaire/config.h
index b247df7859..a5e236e4a9 100644
--- a/keyboards/planck/keymaps/vaire/config.h
+++ b/keyboards/planck/keymaps/vaire/config.h
@@ -1,7 +1,4 @@
-#pragma
-
-
-
+#pragma once
/*
* MIDI options
@@ -15,7 +12,6 @@
#define MOUSEKEY_TIME_TO_MAX 60
#define MOUSEKEY_MAX_SPEED 7
#define MOUSEKEY_WHEEL_DELAY 0
-
#define MIDI_BASIC
diff --git a/keyboards/planck/keymaps/vaire/rules.mk b/keyboards/planck/keymaps/vaire/rules.mk
index f9dfeb7263..427c06822c 100644
--- a/keyboards/planck/keymaps/vaire/rules.mk
+++ b/keyboards/planck/keymaps/vaire/rules.mk
@@ -1,81 +1,3 @@
-# MCU name
-MCU = atmega32u4
-
-# Processor frequency.
-# This will define a symbol, F_CPU, in all source code files equal to the
-# processor frequency in Hz. You can then use this symbol in your source code to
-# calculate timings. Do NOT tack on a 'UL' at the end, this will be done
-# automatically to create a 32-bit value in your source code.
-#
-# This will be an integer division of F_USB below, as it is sourced by
-# F_USB after it has run through any CPU prescalers. Note that this value
-# does not *change* the processor frequency - it should merely be updated to
-# reflect the processor speed set externally so that the code can use accurate
-# software delays.
-F_CPU = 16000000
-
-#
-# LUFA specific
-#
-# Target architecture (see library "Board Types" documentation).
-ARCH = AVR8
-
-# Input clock frequency.
-# This will define a symbol, F_USB, in all source code files equal to the
-# input clock frequency (before any prescaling is performed) in Hz. This value may
-# differ from F_CPU if prescaling is used on the latter, and is required as the
-# raw input clock is fed directly to the PLL sections of the AVR for high speed
-# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
-# at the end, this will be done automatically to create a 32-bit value in your
-# source code.
-#
-# If no clock division is performed on the input clock inside the AVR (via the
-# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
-F_USB = $(F_CPU)
-
-# Bootloader
-# This definition is optional, and if your keyboard supports multiple bootloaders of
-# different sizes, comment this out, and the correct address will be loaded
-# automatically (+60). See bootloader.mk for all options.
-ifeq ($(strip $(KEYBOARD)), planck/rev3)
- BOOTLOADER = atmel-dfu
-endif
-ifeq ($(strip $(KEYBOARD)), planck/rev4)
- BOOTLOADER = atmel-dfu
-endif
-ifeq ($(strip $(KEYBOARD)), planck/rev5)
- BOOTLOADER = qmk-dfu
-endif
-ifeq ($(strip $(KEYBOARD)), planck/light)
- BOOTLOADER = qmk-dfu
-endif
-
-# Interrupt driven control endpoint task(+60)
-OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
-
-# Build Options
-# change to "no" to disable the options, or define them in the Makefile in[]
-# the appropriate keymap folder that will get included automatically
-#
-BOOTMAGIC_ENABLE = no # Virtual DIP switch configuration(+1000)
-MOUSEKEY_ENABLE = yes # Mouse keys(+4700)
-EXTRAKEY_ENABLE = yes # Audio control and System control(+450)
-CONSOLE_ENABLE = no # Console for debug(+400)
-COMMAND_ENABLE = no # Commands for debug and configuration
-NKRO_ENABLE = yes # Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
-BACKLIGHT_ENABLE = yes # Enable keyboard backlight functionality
-MIDI_ENABLE = no # MIDI controls
-AUDIO_ENABLE = yes # Audio output on port C6
-UNICODE_ENABLE = no # Unicode
-BLUETOOTH_ENABLE = no # Enable Bluetooth with the Adafruit EZ-Key HID
-RGBLIGHT_ENABLE = no # Enable WS2812 RGB underlight.
-API_SYSEX_ENABLE = no
-
-# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE
-SLEEP_LED_ENABLE = no # Breathing sleep LED during USB suspend
-
-LAYOUTS = ortho_4x12 planck_mit planck_grid
-LAYOUTS_HAS_RGB = no
-
-DEFAULT_FOLDER = planck/rev5
-
+MOUSEKEY_ENABLE = yes
+CONSOLE_ENABLE = no
+BACKLIGHT_ENABLE = yes