summaryrefslogtreecommitdiffstats
path: root/keyboards/planck/keymaps/handwired_binaryplease
diff options
context:
space:
mode:
Diffstat (limited to 'keyboards/planck/keymaps/handwired_binaryplease')
-rw-r--r--keyboards/planck/keymaps/handwired_binaryplease/config.h36
-rw-r--r--keyboards/planck/keymaps/handwired_binaryplease/rules.mk72
2 files changed, 9 insertions, 99 deletions
diff --git a/keyboards/planck/keymaps/handwired_binaryplease/config.h b/keyboards/planck/keymaps/handwired_binaryplease/config.h
index 8cd4fe40a9..abf9f5771f 100644
--- a/keyboards/planck/keymaps/handwired_binaryplease/config.h
+++ b/keyboards/planck/keymaps/handwired_binaryplease/config.h
@@ -1,37 +1,11 @@
-#ifndef CONFIG_USER_H
-#define CONFIG_USER_H
+#pragma once
-#include "../../config.h"
-
-/* USB Device descriptor parameter */
-
-
-
-#undef VENDOR_ID
-#undef PRODUCT_ID
#undef MANUFACTURER
+#define MANUFACTURER binaryplease
#undef PRODUCT
-#undef MATRIX_ROW_PINS
-#undef MATRIX_COL_PINS
-#undef UNUSED_PINS
-#undef BACKLIGHT_PIN
-#undef BACKLIGHT_LEVELS
-
-
-
-#define VENDOR_ID 0xFEED
-#define PRODUCT_ID 0x6060
-#define MANUFACTURER binaryplease
-#define PRODUCT Teensy_Planck
+#define PRODUCT Teensy_Planck
+#undef MATRIX_ROW_PINS
#define MATRIX_ROW_PINS { D3, D2, D1, D0 }
+#undef MATRIX_COL_PINS
#define MATRIX_COL_PINS { F0, F1, F4, F5, F6, F7, B6, B5, B4, D7, D6, D4 }
-#define UNUSED_PINS
-
-#define BACKLIGHT_PIN B7
-
-/* number of backlight levels */
-#define BACKLIGHT_LEVELS 0
-
-
-#endif
diff --git a/keyboards/planck/keymaps/handwired_binaryplease/rules.mk b/keyboards/planck/keymaps/handwired_binaryplease/rules.mk
index cf37fa6f3b..459c7bce6c 100644
--- a/keyboards/planck/keymaps/handwired_binaryplease/rules.mk
+++ b/keyboards/planck/keymaps/handwired_binaryplease/rules.mk
@@ -1,68 +1,4 @@
-# MCU name
-MCU = atmega32u4
-
-# Processor frequency.
-# This will define a symbol, F_CPU, in all source code files equal to the
-# processor frequency in Hz. You can then use this symbol in your source code to
-# calculate timings. Do NOT tack on a 'UL' at the end, this will be done
-# automatically to create a 32-bit value in your source code.
-#
-# This will be an integer division of F_USB below, as it is sourced by
-# F_USB after it has run through any CPU prescalers. Note that this value
-# does not *change* the processor frequency - it should merely be updated to
-# reflect the processor speed set externally so that the code can use accurate
-# software delays.
-F_CPU = 16000000
-
-#
-# LUFA specific
-#
-# Target architecture (see library "Board Types" documentation).
-ARCH = AVR8
-
-# Input clock frequency.
-# This will define a symbol, F_USB, in all source code files equal to the
-# input clock frequency (before any prescaling is performed) in Hz. This value may
-# differ from F_CPU if prescaling is used on the latter, and is required as the
-# raw input clock is fed directly to the PLL sections of the AVR for high speed
-# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
-# at the end, this will be done automatically to create a 32-bit value in your
-# source code.
-#
-# If no clock division is performed on the input clock inside the AVR (via the
-# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
-F_USB = $(F_CPU)
-
-# Interrupt driven control endpoint task(+60)
-OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
-
-
-# Boot Section Size in *bytes*
-# Teensy halfKay 512
-# Teensy++ halfKay 1024
-# Atmel DFU loader 4096
-# LUFA bootloader 4096
-# USBaspLoader 2048
-OPT_DEFS += -DBOOTLOADER_SIZE=4096
-
-# Build Options
-# change to "no" to disable the options, or define them in the Makefile in
-# the appropriate keymap folder that will get included automatically
-#
-BOOTMAGIC_ENABLE = no # Virtual DIP switch configuration(+1000)
-MOUSEKEY_ENABLE = no # Mouse keys(+4700)
-EXTRAKEY_ENABLE = yes # Audio control and System control(+450)
-CONSOLE_ENABLE = no # Console for debug(+400)
-COMMAND_ENABLE = no # Commands for debug and configuration
-NKRO_ENABLE = no # Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
-BACKLIGHT_ENABLE = no # Enable keyboard backlight functionality
-MIDI_ENABLE = yes # MIDI controls
-AUDIO_ENABLE = no # Audio output on port C6
-UNICODE_ENABLE = no # Unicode
-BLUETOOTH_ENABLE = no # Enable Bluetooth with the Adafruit EZ-Key HID
-RGBLIGHT_ENABLE = no # Enable WS2812 RGB underlight.
-API_SYSEX_ENABLE = no
-
-# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE
-SLEEP_LED_ENABLE = no # Breathing sleep LED during USB suspend
-
+CONSOLE_ENABLE = no
+NKRO_ENABLE = no
+MIDI_ENABLE = yes
+AUDIO_ENABLE = no