summaryrefslogtreecommitdiffstats
path: root/keyboards/hhkb/yang/readme.md
diff options
context:
space:
mode:
Diffstat (limited to 'keyboards/hhkb/yang/readme.md')
-rw-r--r--keyboards/hhkb/yang/readme.md118
1 files changed, 118 insertions, 0 deletions
diff --git a/keyboards/hhkb/yang/readme.md b/keyboards/hhkb/yang/readme.md
new file mode 100644
index 0000000000..6f85c0f198
--- /dev/null
+++ b/keyboards/hhkb/yang/readme.md
@@ -0,0 +1,118 @@
+# HHKB Alternate Controller (YANG HHKB BLE Mod)
+
+![YANG HHKB BLE Mod](https://i.imgur.com/aZP1GYc.jpeg)
+
+An alternative controler for the HHKB designed by YANG (yangdigi)
+based on the hasu controller.
+
+* Keyboard Maintainer: [Kan-Ru Chen](https://github.com/kanru)
+* Hardware Supported: YANG HHKB BLE Controller
+* Hardware Availability: https://kbdfans.com/products/hhkb-ble-mod-upgrade-module
+
+Make example for this keyboard (after setting up your build environment):
+
+ make hhkb/yang:default
+
+To flash, first boot your keyboard into bootloader (hold ESC and attach usb cable)
+then a virtual USB storage should appear. You can copy the `hhkb_yang_default.bin`
+file to the virtual USB storage and override the `HHKB_BLE.BIN` file in there.
+
+Make sure to unmount and eject the virtual USB storage.
+
+## Features:
+
+- [x] QMK (via USB)
+- [x] Bluetooth (BLE)
+- [x] Power saving mode
+ - [x] Idle mode
+ - [x] Deep sleep mode
+- [x] LEDs
+- [x] Battery service
+- [x] Special commands
+ - [x] Switch BT peer
+
+## Entering flash mode
+
+Different ways to enter flash mode:
+
+* Press and hold the ESC key. Insert the USB cable to enter the flash
+ mode. When the OS shows the drive disk, you can release the key.
+
+* Use the magic command LSHIFT+RSHIFT+B to reboot to bootloader then
+ quickly hold the ESC key.
+
+If you reflash the wrong firmware or did not reflash successfully, you
+can no longer enter the flash mode, especially the wireless keyboard
+with battery. You need to turn off the keyboard's power switch, and
+re-enter the flash mode, reflash the correct firmware.
+
+After entering the bootloader(flash mode), three indicators on the top
+right of the HHKB BLE controller will flash. LED3(green) will flash
+quickly when writing firmware to the controller.
+
+If these three leds are not soldered or your hhkb case is black, you
+can't know their status, but you can still see LED3 under the right
+USB port.
+
+## How to reliably flash LUFA MassStorage bootloader on Linux
+
+The FAT filesystem on Linux very often cannot flush the write cache,
+leading to broken firmware in the flash.
+
+We can use `dd` to write to the virtual block storage directly to
+bypass the vfs layer.
+
+```
+dd if=FLASH.bin of=<path of virtual block device> seek=4
+```
+
+Skip 4 sectors because the default sector size of the virtual device
+and dd is 512 bytes and the emulated flash file starts at 5th sector.
+
+## How to find the path of the virtual block device
+
+After the keyboard boots into flash mode, on Linux system you should
+be able to find the block device in `dmesg` logs.
+
+For exmaple if you type
+
+```
+sudo dmesg
+```
+
+You should find something like
+
+```
+[357885.143593] usb 1-1.4: USB disconnect, device number 24
+[357885.627740] usb 1-1.4: new full-speed USB device number 25 using xhci_hcd
+[357885.729486] usb 1-1.4: New USB device found, idVendor=03eb, idProduct=1962, bcdDevice= 0.01
+[357885.729492] usb 1-1.4: New USB device strings: Mfr=0, Product=0, SerialNumber=0
+[357885.745620] SCSI subsystem initialized
+[357885.746712] usb-storage 1-1.4:1.0: USB Mass Storage device detected
+[357885.746818] scsi host0: usb-storage 1-1.4:1.0
+[357885.746919] usbcore: registered new interface driver usb-storage
+[357885.747689] usbcore: registered new interface driver uas
+[357886.766755] scsi 0:0:0:0: Direct-Access LUFA Bootloader 0.00 PQ: 0 ANSI: 0
+[357886.773216] scsi 0:0:0:0: Attached scsi generic sg0 type 0
+[357886.777474] sd 0:0:0:0: [sdx] 134 512-byte logical blocks: (68.6 kB/67.0 KiB)
+[357886.780300] sd 0:0:0:0: [sdx] Write Protect is off
+[357886.780302] sd 0:0:0:0: [sdx] Mode Sense: 00 00 00 00
+[357886.783113] sd 0:0:0:0: [sdx] Asking for cache data failed
+[357886.783114] sd 0:0:0:0: [sdx] Assuming drive cache: write through
+[357886.842676] sdx:
+[357886.859528] sd 0:0:0:0: [sdx] Attached SCSI removable disk
+```
+
+The `sdx` is the block device name and the full path is at `/dev/sdx`
+The above flash command will become
+
+```
+dd if=FLASH.bin of=/dev/sdx seek=4
+```
+
+**Caution**: if set to incorrect device it may wipe out
+your actual disk.
+
+## Help page of original firmware
+
+http://help.ydkb.io/doku.php?id=en:kb-mods:hhkb-ble