summaryrefslogtreecommitdiffstats
path: root/keyboards/handwired/woodpad/rules.mk
diff options
context:
space:
mode:
Diffstat (limited to 'keyboards/handwired/woodpad/rules.mk')
-rw-r--r--keyboards/handwired/woodpad/rules.mk61
1 files changed, 8 insertions, 53 deletions
diff --git a/keyboards/handwired/woodpad/rules.mk b/keyboards/handwired/woodpad/rules.mk
index 4bdc561a63..7725131978 100644
--- a/keyboards/handwired/woodpad/rules.mk
+++ b/keyboards/handwired/woodpad/rules.mk
@@ -1,49 +1,16 @@
# MCU name
MCU = atmega32u4
-# Processor frequency.
-# This will define a symbol, F_CPU, in all source code files equal to the
-# processor frequency in Hz. You can then use this symbol in your source code to
-# calculate timings. Do NOT tack on a 'UL' at the end, this will be done
-# automatically to create a 32-bit value in your source code.
-#
-# This will be an integer division of F_USB below, as it is sourced by
-# F_USB after it has run through any CPU prescalers. Note that this value
-# does not *change* the processor frequency - it should merely be updated to
-# reflect the processor speed set externally so that the code can use accurate
-# software delays.
-F_CPU = 16000000
-
-
-#
-# LUFA specific
-#
-# Target architecture (see library "Board Types" documentation).
-ARCH = AVR8
-
-# Input clock frequency.
-# This will define a symbol, F_USB, in all source code files equal to the
-# input clock frequency (before any prescaling is performed) in Hz. This value may
-# differ from F_CPU if prescaling is used on the latter, and is required as the
-# raw input clock is fed directly to the PLL sections of the AVR for high speed
-# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
-# at the end, this will be done automatically to create a 32-bit value in your
-# source code.
-#
-# If no clock division is performed on the input clock inside the AVR (via the
-# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
-F_USB = $(F_CPU)
-
-# Bootloader
-# This definition is optional, and if your keyboard supports multiple bootloaders of
-# different sizes, comment this out, and the correct address will be loaded
-# automatically (+60). See bootloader.mk for all options.
+# Bootloader selection
+# Teensy halfkay
+# Pro Micro caterina
+# Atmel DFU atmel-dfu
+# LUFA DFU lufa-dfu
+# QMK DFU qmk-dfu
+# ATmega32A bootloadHID
+# ATmega328P USBasp
BOOTLOADER = caterina
-# Interrupt driven control endpoint task(+60)
-OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
-
-
# Build Options
# change yes to no to disable
#
@@ -63,15 +30,3 @@ BLUETOOTH_ENABLE ?= no # Enable Bluetooth with the Adafruit EZ-Key HID
AUDIO_ENABLE ?= no # Audio output on port C6
FAUXCLICKY_ENABLE ?= no # Use buzzer to emulate clicky switches
RGBLIGHT_ENABLE ?= no
-
-#avrdude: build
-# ls /dev/tty* > /tmp/1; \
-# echo "Reset your Pro Micro now"; \
-# while [ -z $$USB ]; do \
-# sleep 1; \
-# ls /dev/tty* > /tmp/2; \
-# USB=`diff /tmp/1 /tmp/2 | $(GREP) -o '/dev/tty.*'`; \
-# done; \
-# avrdude -p $(MCU) -c avr109 -P $$USB -U flash:w:$(BUILD_DIR)/$(TARGET).hex
-#
-#.PHONY: avrdude