summaryrefslogtreecommitdiffstats
path: root/keyboards/handwired/reddot/rules.mk
diff options
context:
space:
mode:
Diffstat (limited to 'keyboards/handwired/reddot/rules.mk')
-rwxr-xr-xkeyboards/handwired/reddot/rules.mk53
1 files changed, 10 insertions, 43 deletions
diff --git a/keyboards/handwired/reddot/rules.mk b/keyboards/handwired/reddot/rules.mk
index 8afe6fc63e..4400decaac 100755
--- a/keyboards/handwired/reddot/rules.mk
+++ b/keyboards/handwired/reddot/rules.mk
@@ -1,44 +1,14 @@
# MCU name
MCU = atmega32u4
-# Processor frequency.
-# This will define a symbol, F_CPU, in all source code files equal to the
-# processor frequency in Hz. You can then use this symbol in your source code to
-# calculate timings. Do NOT tack on a 'UL' at the end, this will be done
-# automatically to create a 32-bit value in your source code.
-#
-# This will be an integer division of F_USB below, as it is sourced by
-# F_USB after it has run through any CPU prescalers. Note that this value
-# does not *change* the processor frequency - it should merely be updated to
-# reflect the processor speed set externally so that the code can use accurate
-# software delays.
-F_CPU = 16000000
-
-# for avr upload
-USB = /dev/cu.usbmodem1421
-#
-# LUFA specific
-#
-# Target architecture (see library "Board Types" documentation).
-ARCH = AVR8
-
-# Input clock frequency.
-# This will define a symbol, F_USB, in all source code files equal to the
-# input clock frequency (before any prescaling is performed) in Hz. This value may
-# differ from F_CPU if prescaling is used on the latter, and is required as the
-# raw input clock is fed directly to the PLL sections of the AVR for high speed
-# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
-# at the end, this will be done automatically to create a 32-bit value in your
-# source code.
-#
-# If no clock division is performed on the input clock inside the AVR (via the
-# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
-F_USB = $(F_CPU)
-
-# Bootloader
-# This definition is optional, and if your keyboard supports multiple bootloaders of
-# different sizes, comment this out, and the correct address will be loaded
-# automatically (+60). See bootloader.mk for all options.
+# Bootloader selection
+# Teensy halfkay
+# Pro Micro caterina
+# Atmel DFU atmel-dfu
+# LUFA DFU lufa-dfu
+# QMK DFU qmk-dfu
+# ATmega32A bootloadHID
+# ATmega328P USBasp
ifdef TEENSY2
BOOTLOADER = halfkay
OPT_DEFS += -DATREUS_TEENSY2
@@ -50,11 +20,6 @@ else
avrdude -p $(MCU) -c avr109 -U flash:w:$(TARGET).hex -P $(USB)
endif
-# Interrupt driven control endpoint task(+60)
-OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
-
-
-
# Build Options
# change yes to no to disable
#
@@ -76,3 +41,5 @@ AUDIO_ENABLE = no # Audio output on port C6
# upload: build
# $(ATREUS_UPLOAD_COMMAND)
+# for avr upload
+USB = /dev/cu.usbmodem1421