diff options
Diffstat (limited to 'keyboards/exclusive/e6v2/le_bmc/rules.mk')
| -rw-r--r-- | keyboards/exclusive/e6v2/le_bmc/rules.mk | 61 |
1 files changed, 4 insertions, 57 deletions
diff --git a/keyboards/exclusive/e6v2/le_bmc/rules.mk b/keyboards/exclusive/e6v2/le_bmc/rules.mk index a9156adeb5..106044ba72 100644 --- a/keyboards/exclusive/e6v2/le_bmc/rules.mk +++ b/keyboards/exclusive/e6v2/le_bmc/rules.mk @@ -1,46 +1,5 @@ # MCU name MCU = atmega32a -PROTOCOL = VUSB - -NO_UART = yes -NO_SUSPEND_POWER_DOWN = yes - -# Processor frequency. -# This will define a symbol, F_CPU, in all source code files equal to the -# processor frequency in Hz. You can then use this symbol in your source code to -# calculate timings. Do NOT tack on a 'UL' at the end, this will be done -# automatically to create a 32-bit value in your source code. -# -# This will be an integer division of F_USB below, as it is sourced by -# F_USB after it has run through any CPU prescalers. Note that this value -# does not *change* the processor frequency - it should merely be updated to -# reflect the processor speed set externally so that the code can use accurate -# software delays. -F_CPU = 12000000 - - -# -# LUFA specific -# -# Target architecture (see library "Board Types" documentation). -# ARCH = AVR8 - -# Input clock frequency. -# This will define a symbol, F_USB, in all source code files equal to the -# input clock frequency (before any prescaling is performed) in Hz. This value may -# differ from F_CPU if prescaling is used on the latter, and is required as the -# raw input clock is fed directly to the PLL sections of the AVR for high speed -# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' -# at the end, this will be done automatically to create a 32-bit value in your -# source code. -# -# If no clock division is performed on the input clock inside the AVR (via the -# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. -# F_USB = $(F_CPU) - -# Interrupt driven control endpoint task(+60) -OPT_DEFS = -DDEBUG_LEVEL=0 - # Bootloader selection # Teensy halfkay @@ -48,20 +7,10 @@ OPT_DEFS = -DDEBUG_LEVEL=0 # Atmel DFU atmel-dfu # LUFA DFU lufa-dfu # QMK DFU qmk-dfu -# atmega32a bootloadHID +# ATmega32A bootloadHID +# ATmega328P USBasp BOOTLOADER = bootloadHID - -# If you don't know the bootloader type, then you can specify the -# Boot Section Size in *bytes* by uncommenting out the OPT_DEFS line -# Teensy halfKay 512 -# Teensy++ halfKay 1024 -# Atmel DFU loader 4096 -# LUFA bootloader 4096 -# USBaspLoader 2048 -# OPT_DEFS += -DBOOTLOADER_SIZE=4096 - - # Build Options # change yes to no to disable # @@ -75,7 +24,7 @@ SLEEP_LED_ENABLE = no # Breathing sleep LED during USB suspend # if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work NKRO_ENABLE = no # USB Nkey Rollover BACKLIGHT_ENABLE = no # Enable keyboard backlight functionality on B7 by default -RGBLIGHT_CUSTOM_DRIVER = yes +WS2812_DRIVER = i2c RGBLIGHT_ENABLE = yes # Enable keyboard RGB underglow MIDI_ENABLE = no # MIDI support (+2400 to 4200, depending on config) UNICODE_ENABLE = no # Unicode @@ -84,6 +33,4 @@ AUDIO_ENABLE = no # Audio output on port C6 FAUXCLICKY_ENABLE = no # Use buzzer to emulate clicky switches HD44780_ENABLE = no # Enable support for HD44780 based LCDs (+400) -SRC += i2c_master.c - -PROGRAM_CMD = ./util/atmega32a_program.py $(TARGET).hex +OPT_DEFS = -DDEBUG_LEVEL=0 |