summaryrefslogtreecommitdiffstats
path: root/keyboards/ergodone/rules.mk
diff options
context:
space:
mode:
Diffstat (limited to 'keyboards/ergodone/rules.mk')
-rw-r--r--keyboards/ergodone/rules.mk80
1 files changed, 15 insertions, 65 deletions
diff --git a/keyboards/ergodone/rules.mk b/keyboards/ergodone/rules.mk
index 6acfaf92e9..4c2fcf1595 100644
--- a/keyboards/ergodone/rules.mk
+++ b/keyboards/ergodone/rules.mk
@@ -1,71 +1,15 @@
-#----------------------------------------------------------------------------
-# On command line:
-#
-# make = Make software.
-#
-# make clean = Clean out built project files.
-#
-# That's pretty much all you need. To compile, always go make clean,
-# followed by make.
-#
-# For advanced users only:
-# make teensy = Download the hex file to the device, using teensy_loader_cli.
-# (must have teensy_loader_cli installed).
-#
-#----------------------------------------------------------------------------
-
-# # project specific files
-SRC = \
- twimaster.c \
- matrix.c \
- expander.c \
-
# MCU name
MCU = atmega32u4
-# Processor frequency.
-# This will define a symbol, F_CPU, in all source code files equal to the
-# processor frequency in Hz. You can then use this symbol in your source code to
-# calculate timings. Do NOT tack on a 'UL' at the end, this will be done
-# automatically to create a 32-bit value in your source code.
-#
-# This will be an integer division of F_USB below, as it is sourced by
-# F_USB after it has run through any CPU prescalers. Note that this value
-# does not *change* the processor frequency - it should merely be updated to
-# reflect the processor speed set externally so that the code can use accurate
-# software delays.
-F_CPU = 16000000
-
-#
-# LUFA specific
-#
-# Target architecture (see library "Board Types" documentation).
-ARCH = AVR8
-
-# Input clock frequency.
-# This will define a symbol, F_USB, in all source code files equal to the
-# input clock frequency (before any prescaling is performed) in Hz. This value may
-# differ from F_CPU if prescaling is used on the latter, and is required as the
-# raw input clock is fed directly to the PLL sections of the AVR for high speed
-# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
-# at the end, this will be done automatically to create a 32-bit value in your
-# source code.
-#
-# If no clock division is performed on the input clock inside the AVR (via the
-# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
-F_USB = $(F_CPU)
-
-# Interrupt driven control endpoint task(+60)
-OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
-
-
-# Boot Section Size in *bytes*
-# Teensy halfKay 512
-# Teensy++ halfKay 1024
-# Atmel DFU loader 4096
-# LUFA bootloader 4096
-# USBaspLoader 2048
-OPT_DEFS += -DBOOTLOADER_SIZE=4096
+# Bootloader selection
+# Teensy halfkay
+# Pro Micro caterina
+# Atmel DFU atmel-dfu
+# LUFA DFU lufa-dfu
+# QMK DFU qmk-dfu
+# ATmega32A bootloadHID
+# ATmega328P USBasp
+BOOTLOADER = caterina
# Build Options
# comment out to disable the options.
@@ -92,4 +36,10 @@ SWAP_HANDS_ENABLE = no # Disable Onehand
RGBLIGHT_ENABLE = no
MIDI_ENABLE = no
+# project specific files
+SRC = \
+ twimaster.c \
+ matrix.c \
+ expander.c \
+
LAYOUTS = ergodox