summaryrefslogtreecommitdiffstats
path: root/docs/feature_led_matrix.md
diff options
context:
space:
mode:
Diffstat (limited to 'docs/feature_led_matrix.md')
-rw-r--r--docs/feature_led_matrix.md103
1 files changed, 103 insertions, 0 deletions
diff --git a/docs/feature_led_matrix.md b/docs/feature_led_matrix.md
index 37f38cc6ed..37c74843aa 100644
--- a/docs/feature_led_matrix.md
+++ b/docs/feature_led_matrix.md
@@ -68,6 +68,109 @@ const is31_led PROGMEM g_is31_leds[DRIVER_LED_TOTAL] = {
Where `Cx_y` is the location of the LED in the matrix defined by [the datasheet](https://www.issi.com/WW/pdf/31FL3731.pdf) and the header file `drivers/led/issi/is31fl3731-simple.h`. The `driver` is the index of the driver you defined in your `config.h` (`0`, `1`, `2`, or `3` ).
---
+### IS31FLCOMMON :id=is31flcommon
+
+There is basic support for addressable LED matrix lighting with a selection of I2C ISSI Lumissil LED controllers through a shared common driver. To enable it, add this to your `rules.mk`:
+
+```makefile
+LED_MATRIX_ENABLE = yes
+LED_MATRIX_DRIVER = <driver name>
+```
+
+Where `<driver name>` is the applicable LED driver chip as below
+
+| Driver Name | Data Sheet | Capability |
+|-------------|------------|------------|
+| `IS31FL3742A` | [datasheet](https://www.lumissil.com/assets/pdf/core/IS31FL3742A_DS.pdf) | 180 LED, 30x6 Matrix |
+| `ISSIFL3743A` | [datasheet](https://www.lumissil.com/assets/pdf/core/IS31FL3743A_DS.pdf) | 198 LED, 18x11 Matrix |
+| `IS31FL3745` | [datasheet](https://www.lumissil.com/assets/pdf/core/IS31FL3745_DS.pdf) | 144 LED, 18x8 Matrix |
+| `IS31FL3746A` | [datasheet](https://www.lumissil.com/assets/pdf/core/IS31FL3746A_DS.pdf) | 72 LED, 18x4 Matrix |
+
+You can use between 1 and 4 IC's. Do not specify `DRIVER_ADDR_<N>` define for IC's if not present on your keyboard. The `DRIVER_ADDR_1` default assumes that all Address pins on the controller have been connected to GND. Drivers that have SYNC functionality have the default settings to disable if 1 driver. If more than 1 drivers then `DRIVER_ADDR_1` will be set to Master and the remaiing ones set to Slave.
+
+Configure the hardware via your `config.h`:
+
+| Variable | Description | Default |
+|----------|-------------|---------|
+| `ISSI_TIMEOUT` | (Optional) How long to wait for i2c messages, in milliseconds | 100 |
+| `ISSI_PERSISTENCE` | (Optional) Retry failed messages this many times | 0 |
+| `DRIVER_COUNT` | (Required) How many LED driver IC's are present | |
+| `DRIVER_LED_TOTAL` | (Required) How many LED lights are present across all drivers | |
+| `DRIVER_ADDR_1` | (Optional) Address for the first LED driver | |
+| `DRIVER_ADDR_<N>` | (Required) Address for the additional LED drivers | |
+| `ISSI_SSR_<N>` | (Optional) Configuration for the Spread Spectrum Register | |
+| `ISSI_CONFIGURATION` | (Optional) Configuration for the Configuration Register | |
+| `ISSI_GLOBALCURRENT` | (Optional) Configuration for the Global Current Register | 0xFF |
+| `ISSI_PULLDOWNUP` | (Optional) Configuration for the Pull Up & Pull Down Register | |
+| `ISSI_TEMP` | (Optional) Configuration for the Tempature Register | |
+| `ISSI_PWM_ENABLE` | (Optional) Configuration for the PWM Enable Register | |
+| `ISSI_PWM_SET` | (Optional) Configuration for the PWM Setting Register | |
+| `ISSI_SCAL_LED ` | (Optional) Configuration for the LEDs Scaling Registers | 0xFF |
+| `ISSI_MANUAL_SCALING` | (Optional) If you wish to configure the Scaling Registers manually | |
+
+
+Defaults
+
+| Variable | IS31FL3742A | IS31FL3743A | IS31FL3745 | IS31FL3746 |
+|----------|-------------|-------------|------------|------------|
+| `DRIVER_ADDR_1` | 0b0110000 | 0b0100000 | 0b0100000 | 0b1100000 |
+| `ISSI_SSR_1` | 0x00 | 0x00 / 0x60 | 0x00 / 0xC0 | 0x00 |
+| `ISSI_SSR_<2-4>` | 0x00 | 0x40 | 0x80 | 0x00 |
+| `ISSI_CONFIGURATION` | 0x31 | 0x01 | 0x31 | 0x01 |
+| `ISSI_PULLDOWNUP` | 0x55 | 0x33 | 0x33 | 0x33 |
+| `ISSI_TEMP` | N/A | 0x00 | 0x00 | 0x00 |
+| `ISSI_PWM_ENABLE` | N/A | N/A | N/A | 0x00 |
+| `ISSI_PWM_SET` | 0x00 | N/A | N/A | 0x00 |
+
+Here is an example using 2 drivers.
+
+```c
+#define DRIVER_ADDR_2 0b0100001
+
+#define DRIVER_COUNT 2
+#define DRIVER_1_LED_TOTAL 66
+#define DRIVER_2_LED_TOTAL 42
+#define DRIVER_LED_TOTAL (DRIVER_1_LED_TOTAL + DRIVER_2_LED_TOTAL)
+```
+!> Note the parentheses, this is so when `DRIVER_LED_TOTAL` is used in code and expanded, the values are added together before any additional math is applied to them. As an example, `rand() % (DRIVER_1_LED_TOTAL + DRIVER_2_LED_TOTAL)` will give very different results than `rand() % DRIVER_1_LED_TOTAL + DRIVER_2_LED_TOTAL`.
+
+Currently only 4 drivers are supported, but it would be trivial to support for more. Note that using a combination of different drivers is not supported. All drivers must be of the same model.
+
+Define these arrays listing all the LEDs in your `<keyboard>.c`:
+
+```c
+const is31_led __flash g_is31_leds[DRIVER_LED_TOTAL] = {
+/* Refer to IS31 manual for these locations
+ * driver
+ * | LED address
+ * | | */
+ { 0, CS1_SW1 },
+ { 0, CS2_SW1 },
+ // ...
+}
+```
+
+Where `CSx_SWx` is the location of the LED in the matrix defined by the datasheet. The `driver` is the index of the driver you defined in your `config.h` (`0`, `1`, `2`, or `3` for now).
+
+`ISSI_MANUAL_SCALING` is used to override the Scaling for individual LED's. By default they will be set as per `ISSI_SCAL_LED`. In `config.h` set how many LED's you want to manually set scaling for.
+Eg `#define ISSI_MANUAL_SCALING 3`
+
+Then Define the array listing all the LEDs you want to override in your `<keyboard>.c`:
+
+```c
+const is31_led __flash g_is31_scaling[ISSI_MANUAL_SCALING] = {
+ * LED Index
+ * | Scaling
+ * | | */
+ {5, 120},
+ {9, 120},
+ ....
+}
+```
+
+Where LED Index is the position of the LED in the `g_is31_leds` array. The `scaling` value between 0 and 255 to be written to the Scaling Register.
+
+---
## Common Configuration :id=common-configuration