summaryrefslogtreecommitdiffstats
diff options
context:
space:
mode:
-rw-r--r--keyboards/clueboard2/Makefile71
-rw-r--r--keyboards/clueboard2/clueboard2.c63
2 files changed, 0 insertions, 134 deletions
diff --git a/keyboards/clueboard2/Makefile b/keyboards/clueboard2/Makefile
deleted file mode 100644
index e9367a90d0..0000000000
--- a/keyboards/clueboard2/Makefile
+++ /dev/null
@@ -1,71 +0,0 @@
-
-
-# MCU name
-#MCU = at90usb1287
-MCU = atmega32u4
-
-# Processor frequency.
-# This will define a symbol, F_CPU, in all source code files equal to the
-# processor frequency in Hz. You can then use this symbol in your source code to
-# calculate timings. Do NOT tack on a 'UL' at the end, this will be done
-# automatically to create a 32-bit value in your source code.
-#
-# This will be an integer division of F_USB below, as it is sourced by
-# F_USB after it has run through any CPU prescalers. Note that this value
-# does not *change* the processor frequency - it should merely be updated to
-# reflect the processor speed set externally so that the code can use accurate
-# software delays.
-F_CPU = 16000000
-
-
-#
-# LUFA specific
-#
-# Target architecture (see library "Board Types" documentation).
-ARCH = AVR8
-
-# Input clock frequency.
-# This will define a symbol, F_USB, in all source code files equal to the
-# input clock frequency (before any prescaling is performed) in Hz. This value may
-# differ from F_CPU if prescaling is used on the latter, and is required as the
-# raw input clock is fed directly to the PLL sections of the AVR for high speed
-# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
-# at the end, this will be done automatically to create a 32-bit value in your
-# source code.
-#
-# If no clock division is performed on the input clock inside the AVR (via the
-# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
-F_USB = $(F_CPU)
-
-# Interrupt driven control endpoint task(+60)
-OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
-
-
-# Boot Section Size in *bytes*
-# Teensy halfKay 512
-# Teensy++ halfKay 1024
-# Atmel DFU loader 4096
-# LUFA bootloader 4096
-# USBaspLoader 2048
-OPT_DEFS += -DBOOTLOADER_SIZE=4096
-
-
-# Build Options
-# comment out to disable the options.
-#
-BOOTMAGIC_ENABLE ?= yes # Virtual DIP switch configuration(+1000)
-MOUSEKEY_ENABLE ?= no # Mouse keys(+4700)
-EXTRAKEY_ENABLE ?= yes # Audio control and System control(+450)
-CONSOLE_ENABLE ?= yes # Console for debug(+400)
-COMMAND_ENABLE ?= yes # Commands for debug and configuration
-NKRO_ENABLE ?= yes # USB Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
-RGBLIGHT_ENABLE ?= no # Enable keyboard underlight functionality (+4870)
-BACKLIGHT_ENABLE ?= yes # Enable keyboard backlight functionality (+1150)
-MIDI_ENABLE ?= no # MIDI controls
-AUDIO_ENABLE ?= no
-UNICODE_ENABLE ?= no # Unicode
-BLUETOOTH_ENABLE ?= no # Enable Bluetooth with the Adafruit EZ-Key HID
-
-ifndef QUANTUM_DIR
- include ../../Makefile
-endif
diff --git a/keyboards/clueboard2/clueboard2.c b/keyboards/clueboard2/clueboard2.c
deleted file mode 100644
index d78ffed9ba..0000000000
--- a/keyboards/clueboard2/clueboard2.c
+++ /dev/null
@@ -1,63 +0,0 @@
-#include "clueboard2.h"
-
-void matrix_init_kb(void) {
- // put your keyboard start-up code here
- // runs once when the firmware starts up
- matrix_init_user();
- led_init_ports();
-
- // JTAG disable for PORT F. write JTD bit twice within four cycles.
- MCUCR |= (1<<JTD);
- MCUCR |= (1<<JTD);
-};
-
-void led_init_ports() {
- // * Set our LED pins as output
- DDRB |= (1<<4);
-}
-
-void led_set_kb(uint8_t usb_led) {
- if (usb_led & (1<<USB_LED_CAPS_LOCK)) {
- // Turn capslock on
- PORTB |= (1<<4);
- } else {
- // Turn capslock off
- PORTB &= ~(1<<4);
- }
-}
-
-/* Clueboard 2.0 LED locations:
- *
- * Capslock: B4, pull high to turn on
- * LCtrl: Shared with Capslock, DO NOT INSTALL LED'S IN BOTH
- * Page Up: B7, pull high to turn on
- * Escape: D6, pull high to turn on
- * Arrows: D4, pull high to turn on
- */
-
-void backlight_init_ports(void) {
- print("init_backlight_pin()\n");
- // Set our LED pins as output
- DDRD |= (1<<6); // Esc
- DDRB |= (1<<7); // Page Up
- DDRD |= (1<<4); // Arrows
-
- // Set our LED pins low
- PORTD &= ~(1<<6); // Esc
- PORTB &= ~(1<<7); // Page Up
- PORTD &= ~(1<<4); // Arrows
-}
-
-void backlight_set(uint8_t level) {
- if ( level == 0 ) {
- // Turn off light
- PORTD |= (1<<6); // Esc
- PORTB |= (1<<7); // Page Up
- PORTD |= (1<<4); // Arrows
- } else {
- // Turn on light
- PORTD &= ~(1<<6); // Esc
- PORTB &= ~(1<<7); // Page Up
- PORTD &= ~(1<<4); // Arrows
- }
-}