Helix/rev2 move to split common (#16723)

17 files changed, 133 insertions, 2039 deletions

diff --git a/keyboards/helix/local_drivers/i2c.c b/keyboards/helix/local_drivers/i2c.c
deleted file mode 100644
index 9221429e96..0000000000
--- a/keyboards/helix/local_drivers/i2c.c
+++ /dev/null
@@ -1,159 +0,0 @@
-#include <util/twi.h>
-#include <avr/io.h>
-#include <stdlib.h>
-#include <avr/interrupt.h>
-#include <util/twi.h>
-#include <stdbool.h>
-#include "i2c.h"
-
-// Limits the amount of we wait for any one i2c transaction.
-// Since were running SCL line 100kHz (=> 10μs/bit), and each transactions is
-// 9 bits, a single transaction will take around 90μs to complete.
-//
-// (F_CPU/SCL_CLOCK)  =>  # of μC cycles to transfer a bit
-// poll loop takes at least 8 clock cycles to execute
-#define I2C_LOOP_TIMEOUT (9+1)*(F_CPU/SCL_CLOCK)/8
-
-#define BUFFER_POS_INC() (slave_buffer_pos = (slave_buffer_pos+1)%SLAVE_BUFFER_SIZE)
-
-volatile uint8_t i2c_slave_buffer[SLAVE_BUFFER_SIZE];
-
-static volatile uint8_t slave_buffer_pos;
-static volatile bool slave_has_register_set = false;
-
-// Wait for an i2c operation to finish
-inline static
-void i2c_delay(void) {
-  uint16_t lim = 0;
-  while(!(TWCR & (1<<TWINT)) && lim < I2C_LOOP_TIMEOUT)
-    lim++;
-
-  // easier way, but will wait slightly longer
-  // _delay_us(100);
-}
-
-// Setup twi to run at 100kHz or 400kHz (see ./i2c.h SCL_CLOCK)
-void i2c_master_init(void) {
-  // no prescaler
-  TWSR = 0;
-  // Set TWI clock frequency to SCL_CLOCK. Need TWBR>10.
-  // Check datasheets for more info.
-  TWBR = ((F_CPU/SCL_CLOCK)-16)/2;
-}
-
-// Start a transaction with the given i2c slave address. The direction of the
-// transfer is set with I2C_READ and I2C_WRITE.
-// returns: 0 => success
-//          1 => error
-uint8_t i2c_master_start(uint8_t address) {
-  TWCR = (1<<TWINT) | (1<<TWEN) | (1<<TWSTA);
-
-  i2c_delay();
-
-  // check that we started successfully
-  if ( (TW_STATUS != TW_START) && (TW_STATUS != TW_REP_START))
-    return 1;
-
-  TWDR = address;
-  TWCR = (1<<TWINT) | (1<<TWEN);
-
-  i2c_delay();
-
-  if ( (TW_STATUS != TW_MT_SLA_ACK) && (TW_STATUS != TW_MR_SLA_ACK) )
-    return 1; // slave did not acknowledge
-  else
-    return 0; // success
-}
-
-
-// Finish the i2c transaction.
-void i2c_master_stop(void) {
-  TWCR = (1<<TWINT) | (1<<TWEN) | (1<<TWSTO);
-
-  uint16_t lim = 0;
-  while(!(TWCR & (1<<TWSTO)) && lim < I2C_LOOP_TIMEOUT)
-    lim++;
-}
-
-// Write one byte to the i2c slave.
-// returns 0 => slave ACK
-//         1 => slave NACK
-uint8_t i2c_master_write(uint8_t data) {
-  TWDR = data;
-  TWCR = (1<<TWINT) | (1<<TWEN);
-
-  i2c_delay();
-
-  // check if the slave acknowledged us
-  return (TW_STATUS == TW_MT_DATA_ACK) ? 0 : 1;
-}
-
-// Read one byte from the i2c slave. If ack=1 the slave is acknowledged,
-// if ack=0 the acknowledge bit is not set.
-// returns: byte read from i2c device
-uint8_t i2c_master_read(int ack) {
-  TWCR = (1<<TWINT) | (1<<TWEN) | (ack<<TWEA);
-
-  i2c_delay();
-  return TWDR;
-}
-
-void i2c_reset_state(void) {
-  TWCR = 0;
-}
-
-void i2c_slave_init(uint8_t address) {
-  TWAR = address << 0; // slave i2c address
-  // TWEN  - twi enable
-  // TWEA  - enable address acknowledgement
-  // TWINT - twi interrupt flag
-  // TWIE  - enable the twi interrupt
-  TWCR = (1<<TWIE) | (1<<TWEA) | (1<<TWINT) | (1<<TWEN);
-}
-
-ISR(TWI_vect);
-
-ISR(TWI_vect) {
-  uint8_t ack = 1;
-  switch(TW_STATUS) {
-    case TW_SR_SLA_ACK:
-      // this device has been addressed as a slave receiver
-      slave_has_register_set = false;
-      break;
-
-    case TW_SR_DATA_ACK:
-      // this device has received data as a slave receiver
-      // The first byte that we receive in this transaction sets the location
-      // of the read/write location of the slaves memory that it exposes over
-      // i2c.  After that, bytes will be written at slave_buffer_pos, incrementing
-      // slave_buffer_pos after each write.
-      if(!slave_has_register_set) {
-        slave_buffer_pos = TWDR;
-        // don't acknowledge the master if this memory loctaion is out of bounds
-        if ( slave_buffer_pos >= SLAVE_BUFFER_SIZE ) {
-          ack = 0;
-          slave_buffer_pos = 0;
-        }
-        slave_has_register_set = true;
-      } else {
-        i2c_slave_buffer[slave_buffer_pos] = TWDR;
-        BUFFER_POS_INC();
-      }
-      break;
-
-    case TW_ST_SLA_ACK:
-    case TW_ST_DATA_ACK:
-      // master has addressed this device as a slave transmitter and is
-      // requesting data.
-      TWDR = i2c_slave_buffer[slave_buffer_pos];
-      BUFFER_POS_INC();
-      break;
-
-    case TW_BUS_ERROR: // something went wrong, reset twi state
-      TWCR = 0;
-    default:
-      break;
-  }
-  // Reset everything, so we are ready for the next TWI interrupt
-  TWCR |= (1<<TWIE) | (1<<TWINT) | (ack<<TWEA) | (1<<TWEN);
-}
diff --git a/keyboards/helix/local_drivers/i2c.h b/keyboards/helix/local_drivers/i2c.h
deleted file mode 100644
index 710662c7ab..0000000000
--- a/keyboards/helix/local_drivers/i2c.h
+++ /dev/null
@@ -1,46 +0,0 @@
-#pragma once
-
-#include <stdint.h>
-
-#ifndef F_CPU
-#define F_CPU 16000000UL
-#endif
-
-#define I2C_READ 1
-#define I2C_WRITE 0
-
-#define I2C_ACK 1
-#define I2C_NACK 0
-
-#define SLAVE_BUFFER_SIZE 0x10
-
-// i2c SCL clock frequency 400kHz
-#define SCL_CLOCK  400000L
-
-extern volatile uint8_t i2c_slave_buffer[SLAVE_BUFFER_SIZE];
-
-void i2c_master_init(void);
-uint8_t i2c_master_start(uint8_t address);
-void i2c_master_stop(void);
-uint8_t i2c_master_write(uint8_t data);
-uint8_t i2c_master_read(int);
-void i2c_reset_state(void);
-void i2c_slave_init(uint8_t address);
-
-
-static inline unsigned char i2c_start_read(unsigned char addr) {
-  return i2c_master_start((addr << 1) | I2C_READ);
-}
-
-static inline unsigned char i2c_start_write(unsigned char addr) {
-  return i2c_master_start((addr << 1) | I2C_WRITE);
-}
-
-// from SSD1306 scrips
-extern unsigned char i2c_rep_start(unsigned char addr);
-extern void i2c_start_wait(unsigned char addr);
-extern unsigned char i2c_readAck(void);
-extern unsigned char i2c_readNak(void);
-extern unsigned char i2c_read(unsigned char ack);
-
-#define i2c_read(ack)  (ack) ? i2c_readAck() : i2c_readNak();
diff --git a/keyboards/helix/local_drivers/serial.c b/keyboards/helix/local_drivers/serial.c
deleted file mode 100644
index 674c42d593..0000000000
--- a/keyboards/helix/local_drivers/serial.c
+++ /dev/null
@@ -1,589 +0,0 @@
-/*
- * WARNING: be careful changing this code, it is very timing dependent
- *
- * 2018-10-28 checked
- *  avr-gcc 4.9.2
- *  avr-gcc 5.4.0
- *  avr-gcc 7.3.0
- */
-
-#ifndef F_CPU
-#define F_CPU 16000000
-#endif
-
-#include <avr/io.h>
-#include <avr/interrupt.h>
-#include <util/delay.h>
-#include <stddef.h>
-#include <stdbool.h>
-#include "serial.h"
-
-#ifdef SOFT_SERIAL_PIN
-
-#ifdef __AVR_ATmega32U4__
-  // if using ATmega32U4 I2C, can not use PD0 and PD1 in soft serial.
-  #ifdef USE_I2C
-    #if SOFT_SERIAL_PIN == D0 || SOFT_SERIAL_PIN == D1
-      #error Using ATmega32U4 I2C, so can not use PD0, PD1
-    #endif
-  #endif
-
-  #if SOFT_SERIAL_PIN >= D0 && SOFT_SERIAL_PIN <= D3
-    #define SERIAL_PIN_DDR   DDRD
-    #define SERIAL_PIN_PORT  PORTD
-    #define SERIAL_PIN_INPUT PIND
-    #if SOFT_SERIAL_PIN == D0
-      #define SERIAL_PIN_MASK _BV(PD0)
-      #define EIMSK_BIT       _BV(INT0)
-      #define EICRx_BIT       (~(_BV(ISC00) | _BV(ISC01)))
-      #define SERIAL_PIN_INTERRUPT INT0_vect
-    #elif  SOFT_SERIAL_PIN == D1
-      #define SERIAL_PIN_MASK _BV(PD1)
-      #define EIMSK_BIT       _BV(INT1)
-      #define EICRx_BIT       (~(_BV(ISC10) | _BV(ISC11)))
-      #define SERIAL_PIN_INTERRUPT INT1_vect
-    #elif  SOFT_SERIAL_PIN == D2
-      #define SERIAL_PIN_MASK _BV(PD2)
-      #define EIMSK_BIT       _BV(INT2)
-      #define EICRx_BIT       (~(_BV(ISC20) | _BV(ISC21)))
-      #define SERIAL_PIN_INTERRUPT INT2_vect
-    #elif  SOFT_SERIAL_PIN == D3
-      #define SERIAL_PIN_MASK _BV(PD3)
-      #define EIMSK_BIT       _BV(INT3)
-      #define EICRx_BIT       (~(_BV(ISC30) | _BV(ISC31)))
-      #define SERIAL_PIN_INTERRUPT INT3_vect
-    #endif
-  #elif  SOFT_SERIAL_PIN == E6
-    #define SERIAL_PIN_DDR   DDRE
-    #define SERIAL_PIN_PORT  PORTE
-    #define SERIAL_PIN_INPUT PINE
-    #define SERIAL_PIN_MASK  _BV(PE6)
-    #define EIMSK_BIT        _BV(INT6)
-    #define EICRx_BIT        (~(_BV(ISC60) | _BV(ISC61)))
-    #define SERIAL_PIN_INTERRUPT INT6_vect
-  #else
-  #error invalid SOFT_SERIAL_PIN value
-  #endif
-
-#else
- #error serial.c now support ATmega32U4 only
-#endif
-
-//////////////// for backward compatibility ////////////////////////////////
-#if !defined(SERIAL_USE_SINGLE_TRANSACTION) && !defined(SERIAL_USE_MULTI_TRANSACTION)
-/* --- USE OLD API (compatible with let's split serial.c) */
-  #if SERIAL_SLAVE_BUFFER_LENGTH > 0
-  uint8_t volatile serial_slave_buffer[SERIAL_SLAVE_BUFFER_LENGTH] = {0};
-  #endif
-  #if SERIAL_MASTER_BUFFER_LENGTH > 0
-  uint8_t volatile serial_master_buffer[SERIAL_MASTER_BUFFER_LENGTH] = {0};
-  #endif
-  uint8_t volatile status0 = 0;
-
-SSTD_t transactions[] = {
-    { (uint8_t *)&status0,
-  #if SERIAL_MASTER_BUFFER_LENGTH > 0
-      sizeof(serial_master_buffer), (uint8_t *)serial_master_buffer,
-  #else
-      0, (uint8_t *)NULL,
-  #endif
-  #if SERIAL_SLAVE_BUFFER_LENGTH > 0
-      sizeof(serial_slave_buffer), (uint8_t *)serial_slave_buffer
-  #else
-      0, (uint8_t *)NULL,
-  #endif
-  }
-};
-
-void serial_master_init(void)
-{ soft_serial_initiator_init(transactions, TID_LIMIT(transactions)); }
-
-void serial_slave_init(void)
-{ soft_serial_target_init(transactions, TID_LIMIT(transactions)); }
-
-// 0 => no error
-// 1 => slave did not respond
-// 2 => checksum error
-int serial_update_buffers()
-{
-    int result;
-    result = soft_serial_transaction();
-    return result;
-}
-
-#endif // end of OLD API (compatible with let's split serial.c)
-////////////////////////////////////////////////////////////////////////////
-
-#define ALWAYS_INLINE __attribute__((always_inline))
-#define NO_INLINE __attribute__((noinline))
-#define _delay_sub_us(x)    __builtin_avr_delay_cycles(x)
-
-// parity check
-#define ODD_PARITY 1
-#define EVEN_PARITY 0
-#define PARITY EVEN_PARITY
-
-#ifdef SERIAL_DELAY
-  // custom setup in config.h
-  // #define TID_SEND_ADJUST 2
-  // #define SERIAL_DELAY 6             // micro sec
-  // #define READ_WRITE_START_ADJUST 30 // cycles
-  // #define READ_WRITE_WIDTH_ADJUST 8 // cycles
-#else
-// ============ Standard setups ============
-
-#ifndef SELECT_SOFT_SERIAL_SPEED
-#define SELECT_SOFT_SERIAL_SPEED 1
-//  0: about 189kbps
-//  1: about 137kbps (default)
-//  2: about 75kbps
-//  3: about 39kbps
-//  4: about 26kbps
-//  5: about 20kbps
-#endif
-
-#if __GNUC__ < 6
-  #define TID_SEND_ADJUST 14
-#else
-  #define TID_SEND_ADJUST 2
-#endif
-
-#if SELECT_SOFT_SERIAL_SPEED == 0
-  // Very High speed
-  #define SERIAL_DELAY 4             // micro sec
-  #if __GNUC__ < 6
-    #define READ_WRITE_START_ADJUST 33 // cycles
-    #define READ_WRITE_WIDTH_ADJUST 3 // cycles
-  #else
-    #define READ_WRITE_START_ADJUST 34 // cycles
-    #define READ_WRITE_WIDTH_ADJUST 7 // cycles
-  #endif
-#elif SELECT_SOFT_SERIAL_SPEED == 1
-  // High speed
-  #define SERIAL_DELAY 6             // micro sec
-  #if __GNUC__ < 6
-    #define READ_WRITE_START_ADJUST 30 // cycles
-    #define READ_WRITE_WIDTH_ADJUST 3 // cycles
-  #else
-    #define READ_WRITE_START_ADJUST 33 // cycles
-    #define READ_WRITE_WIDTH_ADJUST 7 // cycles
-  #endif
-#elif SELECT_SOFT_SERIAL_SPEED == 2
-  // Middle speed
-  #define SERIAL_DELAY 12            // micro sec
-  #define READ_WRITE_START_ADJUST 30 // cycles
-  #if __GNUC__ < 6
-    #define READ_WRITE_WIDTH_ADJUST 3 // cycles
-  #else
-    #define READ_WRITE_WIDTH_ADJUST 7 // cycles
-  #endif
-#elif SELECT_SOFT_SERIAL_SPEED == 3
-  // Low speed
-  #define SERIAL_DELAY 24            // micro sec
-  #define READ_WRITE_START_ADJUST 30 // cycles
-  #if __GNUC__ < 6
-    #define READ_WRITE_WIDTH_ADJUST 3 // cycles
-  #else
-    #define READ_WRITE_WIDTH_ADJUST 7 // cycles
-  #endif
-#elif SELECT_SOFT_SERIAL_SPEED == 4
-  // Very Low speed
-  #define SERIAL_DELAY 36            // micro sec
-  #define READ_WRITE_START_ADJUST 30 // cycles
-  #if __GNUC__ < 6
-    #define READ_WRITE_WIDTH_ADJUST 3 // cycles
-  #else
-    #define READ_WRITE_WIDTH_ADJUST 7 // cycles
-  #endif
-#elif SELECT_SOFT_SERIAL_SPEED == 5
-  // Ultra Low speed
-  #define SERIAL_DELAY 48            // micro sec
-  #define READ_WRITE_START_ADJUST 30 // cycles
-  #if __GNUC__ < 6
-    #define READ_WRITE_WIDTH_ADJUST 3 // cycles
-  #else
-    #define READ_WRITE_WIDTH_ADJUST 7 // cycles
-  #endif
-#else
-#error invalid SELECT_SOFT_SERIAL_SPEED value
-#endif /* SELECT_SOFT_SERIAL_SPEED */
-#endif /* SERIAL_DELAY */
-
-#define SERIAL_DELAY_HALF1 (SERIAL_DELAY/2)
-#define SERIAL_DELAY_HALF2 (SERIAL_DELAY - SERIAL_DELAY/2)
-
-#define SLAVE_INT_WIDTH_US 1
-#ifndef SERIAL_USE_MULTI_TRANSACTION
-  #define SLAVE_INT_RESPONSE_TIME SERIAL_DELAY
-#else
-  #define SLAVE_INT_ACK_WIDTH_UNIT 2
-  #define SLAVE_INT_ACK_WIDTH 4
-#endif
-
-static SSTD_t *Transaction_table = NULL;
-static uint8_t Transaction_table_size = 0;
-
-inline static void serial_delay(void) ALWAYS_INLINE;
-inline static
-void serial_delay(void) {
-  _delay_us(SERIAL_DELAY);
-}
-
-inline static void serial_delay_half1(void) ALWAYS_INLINE;
-inline static
-void serial_delay_half1(void) {
-  _delay_us(SERIAL_DELAY_HALF1);
-}
-
-inline static void serial_delay_half2(void) ALWAYS_INLINE;
-inline static
-void serial_delay_half2(void) {
-  _delay_us(SERIAL_DELAY_HALF2);
-}
-
-inline static void serial_output(void) ALWAYS_INLINE;
-inline static
-void serial_output(void) {
-  SERIAL_PIN_DDR |= SERIAL_PIN_MASK;
-}
-
-// make the serial pin an input with pull-up resistor
-inline static void serial_input_with_pullup(void) ALWAYS_INLINE;
-inline static
-void serial_input_with_pullup(void) {
-  SERIAL_PIN_DDR  &= ~SERIAL_PIN_MASK;
-  SERIAL_PIN_PORT |= SERIAL_PIN_MASK;
-}
-
-inline static uint8_t serial_read_pin(void) ALWAYS_INLINE;
-inline static
-uint8_t serial_read_pin(void) {
-  return !!(SERIAL_PIN_INPUT & SERIAL_PIN_MASK);
-}
-
-inline static void serial_low(void) ALWAYS_INLINE;
-inline static
-void serial_low(void) {
-  SERIAL_PIN_PORT &= ~SERIAL_PIN_MASK;
-}
-
-inline static void serial_high(void) ALWAYS_INLINE;
-inline static
-void serial_high(void) {
-  SERIAL_PIN_PORT |= SERIAL_PIN_MASK;
-}
-
-void soft_serial_initiator_init(SSTD_t *sstd_table, int sstd_table_size)
-{
-    Transaction_table = sstd_table;
-    Transaction_table_size = (uint8_t)sstd_table_size;
-    serial_output();
-    serial_high();
-}
-
-void soft_serial_target_init(SSTD_t *sstd_table, int sstd_table_size)
-{
-    Transaction_table = sstd_table;
-    Transaction_table_size = (uint8_t)sstd_table_size;
-    serial_input_with_pullup();
-
-    // Enable INT0-INT3,INT6
-    EIMSK |= EIMSK_BIT;
-#if SERIAL_PIN_MASK == _BV(PE6)
-    // Trigger on falling edge of INT6
-    EICRB &= EICRx_BIT;
-#else
-    // Trigger on falling edge of INT0-INT3
-    EICRA &= EICRx_BIT;
-#endif
-}
-
-// Used by the sender to synchronize timing with the reciver.
-static void sync_recv(void) NO_INLINE;
-static
-void sync_recv(void) {
-  for (uint8_t i = 0; i < SERIAL_DELAY*5 && serial_read_pin(); i++ ) {
-  }
-  // This shouldn't hang if the target disconnects because the
-  // serial line will float to high if the target does disconnect.
-  while (!serial_read_pin());
-}
-
-// Used by the reciver to send a synchronization signal to the sender.
-static void sync_send(void) NO_INLINE;
-static
-void sync_send(void) {
-  serial_low();
-  serial_delay();
-  serial_high();
-}
-
-// Reads a byte from the serial line
-static uint8_t serial_read_chunk(uint8_t *pterrcount, uint8_t bit) NO_INLINE;
-static uint8_t serial_read_chunk(uint8_t *pterrcount, uint8_t bit) {
-    uint8_t byte, i, p, pb;
-
-  _delay_sub_us(READ_WRITE_START_ADJUST);
-  for( i = 0, byte = 0, p = PARITY; i < bit; i++ ) {
-      serial_delay_half1();   // read the middle of pulses
-      if( serial_read_pin() ) {
-          byte = (byte << 1) | 1; p ^= 1;
-      } else {
-          byte = (byte << 1) | 0; p ^= 0;
-      }
-      _delay_sub_us(READ_WRITE_WIDTH_ADJUST);
-      serial_delay_half2();
-  }
-  /* recive parity bit */
-  serial_delay_half1();   // read the middle of pulses
-  pb = serial_read_pin();
-  _delay_sub_us(READ_WRITE_WIDTH_ADJUST);
-  serial_delay_half2();
-
-  *pterrcount += (p != pb)? 1 : 0;
-
-  return byte;
-}
-
-// Sends a byte with MSB ordering
-void serial_write_chunk(uint8_t data, uint8_t bit) NO_INLINE;
-void serial_write_chunk(uint8_t data, uint8_t bit) {
-    uint8_t b, p;
-    for( p = PARITY, b = 1<<(bit-1); b ; b >>= 1) {
-        if(data & b) {
-            serial_high(); p ^= 1;
-        } else {
-            serial_low();  p ^= 0;
-        }
-        serial_delay();
-    }
-    /* send parity bit */
-    if(p & 1) { serial_high(); }
-    else      { serial_low(); }
-    serial_delay();
-
-    serial_low(); // sync_send() / senc_recv() need raise edge
-}
-
-static void serial_send_packet(uint8_t *buffer, uint8_t size) NO_INLINE;
-static
-void serial_send_packet(uint8_t *buffer, uint8_t size) {
-  for (uint8_t i = 0; i < size; ++i) {
-    uint8_t data;
-    data = buffer[i];
-    sync_send();
-    serial_write_chunk(data,8);
-  }
-}
-
-static uint8_t serial_recive_packet(uint8_t *buffer, uint8_t size) NO_INLINE;
-static
-uint8_t serial_recive_packet(uint8_t *buffer, uint8_t size) {
-  uint8_t pecount = 0;
-  for (uint8_t i = 0; i < size; ++i) {
-    uint8_t data;
-    sync_recv();
-    data = serial_read_chunk(&pecount, 8);
-    buffer[i] = data;
-  }
-  return pecount == 0;
-}
-
-inline static
-void change_sender2reciver(void) {
-    sync_send();          //0
-    serial_delay_half1(); //1
-    serial_low();         //2
-    serial_input_with_pullup(); //2
-    serial_delay_half1(); //3
-}
-
-inline static
-void change_reciver2sender(void) {
-    sync_recv();     //0
-    serial_delay();  //1
-    serial_low();    //3
-    serial_output(); //3
-    serial_delay_half1(); //4
-}
-
-static inline uint8_t nibble_bits_count(uint8_t bits)
-{
-    bits = (bits & 0x5) + (bits >> 1 & 0x5);
-    bits = (bits & 0x3) + (bits >> 2 & 0x3);
-    return bits;
-}
-
-// interrupt handle to be used by the target device
-ISR(SERIAL_PIN_INTERRUPT) {
-
-#ifndef SERIAL_USE_MULTI_TRANSACTION
-  serial_low();
-  serial_output();
-  SSTD_t *trans = Transaction_table;
-#else
-  // recive transaction table index
-  uint8_t tid, bits;
-  uint8_t pecount = 0;
-  sync_recv();
-  bits = serial_read_chunk(&pecount,7);
-  tid = bits>>3;
-  bits = (bits&7) != nibble_bits_count(tid);
-  if( bits || pecount> 0 || tid > Transaction_table_size ) {
-      return;
-  }
-  serial_delay_half1();
-
-  serial_high(); // response step1 low->high
-  serial_output();
-  _delay_sub_us(SLAVE_INT_ACK_WIDTH_UNIT*SLAVE_INT_ACK_WIDTH);
-  SSTD_t *trans = &Transaction_table[tid];
-  serial_low(); // response step2 ack high->low
-#endif
-
-  // target send phase
-  if( trans->target2initiator_buffer_size > 0 )
-      serial_send_packet((uint8_t *)trans->target2initiator_buffer,
-                         trans->target2initiator_buffer_size);
-  // target switch to input
-  change_sender2reciver();
-
-  // target recive phase
-  if( trans->initiator2target_buffer_size > 0 ) {
-      if (serial_recive_packet((uint8_t *)trans->initiator2target_buffer,
-                               trans->initiator2target_buffer_size) ) {
-          *trans->status = TRANSACTION_ACCEPTED;
-      } else {
-          *trans->status = TRANSACTION_DATA_ERROR;
-      }
-  } else {
-      *trans->status = TRANSACTION_ACCEPTED;
-  }
-
-  sync_recv(); //weit initiator output to high
-}
-
-/////////
-//  start transaction by initiator
-//
-// int  soft_serial_transaction(int sstd_index)
-//
-// Returns:
-//    TRANSACTION_END
-//    TRANSACTION_NO_RESPONSE
-//    TRANSACTION_DATA_ERROR
-// this code is very time dependent, so we need to disable interrupts
-#ifndef SERIAL_USE_MULTI_TRANSACTION
-int  soft_serial_transaction(void) {
-  SSTD_t *trans = Transaction_table;
-#else
-int  soft_serial_transaction(int sstd_index) {
-  if( sstd_index > Transaction_table_size )
-      return TRANSACTION_TYPE_ERROR;
-  SSTD_t *trans = &Transaction_table[sstd_index];
-#endif
-  cli();
-
-  // signal to the target that we want to start a transaction
-  serial_output();
-  serial_low();
-  _delay_us(SLAVE_INT_WIDTH_US);
-
-#ifndef SERIAL_USE_MULTI_TRANSACTION
-  // wait for the target response
-  serial_input_with_pullup();
-  _delay_us(SLAVE_INT_RESPONSE_TIME);
-
-  // check if the target is present
-  if (serial_read_pin()) {
-    // target failed to pull the line low, assume not present
-    serial_output();
-    serial_high();
-    *trans->status = TRANSACTION_NO_RESPONSE;
-    sei();
-    return TRANSACTION_NO_RESPONSE;
-  }
-
-#else
-  // send transaction table index
-  int tid = (sstd_index<<3) | (7 & nibble_bits_count(sstd_index));
-  sync_send();
-  _delay_sub_us(TID_SEND_ADJUST);
-  serial_write_chunk(tid, 7);
-  serial_delay_half1();
-
-  // wait for the target response (step1 low->high)
-  serial_input_with_pullup();
-  while( !serial_read_pin() ) {
-      _delay_sub_us(2);
-  }
-
-  // check if the target is present (step2 high->low)
-  for( int i = 0; serial_read_pin(); i++ ) {
-      if (i > SLAVE_INT_ACK_WIDTH + 1) {
-          // slave failed to pull the line low, assume not present
-          serial_output();
-          serial_high();
-          *trans->status = TRANSACTION_NO_RESPONSE;
-          sei();
-          return TRANSACTION_NO_RESPONSE;
-      }
-      _delay_sub_us(SLAVE_INT_ACK_WIDTH_UNIT);
-  }
-#endif
-
-  // initiator recive phase
-  // if the target is present syncronize with it
-  if( trans->target2initiator_buffer_size > 0 ) {
-      if (!serial_recive_packet((uint8_t *)trans->target2initiator_buffer,
-                                trans->target2initiator_buffer_size) ) {
-          serial_output();
-          serial_high();
-          *trans->status = TRANSACTION_DATA_ERROR;
-          sei();
-          return TRANSACTION_DATA_ERROR;
-      }
-   }
-
-  // initiator switch to output
-  change_reciver2sender();
-
-  // initiator send phase
-  if( trans->initiator2target_buffer_size > 0 ) {
-      serial_send_packet((uint8_t *)trans->initiator2target_buffer,
-                         trans->initiator2target_buffer_size);
-  }
-
-  // always, release the line when not in use
-  sync_send();
-
-  *trans->status = TRANSACTION_END;
-  sei();
-  return TRANSACTION_END;
-}
-
-#ifdef SERIAL_USE_MULTI_TRANSACTION
-int soft_serial_get_and_clean_status(int sstd_index) {
-    SSTD_t *trans = &Transaction_table[sstd_index];
-    cli();
-    int retval = *trans->status;
-    *trans->status = 0;;
-    sei();
-    return retval;
-}
-#endif
-
-#endif
-
-// Helix serial.c history
-//   2018-1-29 fork from let's split and add PD2, modify sync_recv() (#2308, bceffdefc)
-//   2018-6-28 bug fix master to slave comm and speed up (#3255, 1038bbef4)
-//             (adjusted with avr-gcc 4.9.2)
-//   2018-7-13 remove USE_SERIAL_PD2 macro (#3374, f30d6dd78)
-//             (adjusted with avr-gcc 4.9.2)
-//   2018-8-11 add support multi-type transaction (#3608, feb5e4aae)
-//             (adjusted with avr-gcc 4.9.2)
-//   2018-10-21 fix serial and RGB animation conflict (#4191, 4665e4fff)
-//             (adjusted with avr-gcc 7.3.0)
-//   2018-10-28 re-adjust compiler depend value of delay (#4269, 8517f8a66)
-//             (adjusted with avr-gcc 5.4.0, 7.3.0)
diff --git a/keyboards/helix/local_drivers/serial.h b/keyboards/helix/local_drivers/serial.h
deleted file mode 100644
index b4dcdafe57..0000000000
--- a/keyboards/helix/local_drivers/serial.h
+++ /dev/null
@@ -1,86 +0,0 @@
-#pragma once
-
-#include <stdbool.h>
-
-// /////////////////////////////////////////////////////////////////
-// Need Soft Serial defines in config.h
-// /////////////////////////////////////////////////////////////////
-// ex.
-//  #define SOFT_SERIAL_PIN ??   // ?? = D0,D1,D2,D3,E6
-//  OPTIONAL: #define SELECT_SOFT_SERIAL_SPEED ? // ? = 1,2,3,4,5
-//                                               //  1: about 137kbps (default)
-//                                               //  2: about 75kbps
-//                                               //  3: about 39kbps
-//                                               //  4: about 26kbps
-//                                               //  5: about 20kbps
-//
-// //// USE OLD API (compatible with let's split serial.c)
-// ex.
-//  #define SERIAL_SLAVE_BUFFER_LENGTH MATRIX_ROWS/2
-//  #define SERIAL_MASTER_BUFFER_LENGTH 1
-//
-// //// USE NEW API
-//    //// USE simple API (using signle-type transaction function)
-//      #define SERIAL_USE_SINGLE_TRANSACTION
-//    //// USE flexible API (using multi-type transaction function)
-//      #define SERIAL_USE_MULTI_TRANSACTION
-//
-// /////////////////////////////////////////////////////////////////
-
-
-//////////////// for backward compatibility ////////////////////////////////
-#if !defined(SERIAL_USE_SINGLE_TRANSACTION) && !defined(SERIAL_USE_MULTI_TRANSACTION)
-/* --- USE OLD API (compatible with let's split serial.c) */
- #if SERIAL_SLAVE_BUFFER_LENGTH > 0
- extern volatile uint8_t serial_slave_buffer[SERIAL_SLAVE_BUFFER_LENGTH];
- #endif
- #if SERIAL_MASTER_BUFFER_LENGTH > 0
- extern volatile uint8_t serial_master_buffer[SERIAL_MASTER_BUFFER_LENGTH];
- #endif
-
- void serial_master_init(void);
- void serial_slave_init(void);
- int serial_update_buffers(void);
-
-#endif // end of USE OLD API
-////////////////////////////////////////////////////////////////////////////
-
-// Soft Serial Transaction Descriptor
-typedef struct _SSTD_t  {
-    uint8_t *status;
-    uint8_t initiator2target_buffer_size;
-    uint8_t *initiator2target_buffer;
-    uint8_t target2initiator_buffer_size;
-    uint8_t *target2initiator_buffer;
-} SSTD_t;
-#define TID_LIMIT( table ) (sizeof(table) / sizeof(SSTD_t))
-
-// initiator is transaction start side
-void soft_serial_initiator_init(SSTD_t *sstd_table, int sstd_table_size);
-// target is interrupt accept side
-void soft_serial_target_init(SSTD_t *sstd_table, int sstd_table_size);
-
-// initiator resullt
-#define TRANSACTION_END 0
-#define TRANSACTION_NO_RESPONSE 0x1
-#define TRANSACTION_DATA_ERROR  0x2
-#define TRANSACTION_TYPE_ERROR  0x4
-#ifndef SERIAL_USE_MULTI_TRANSACTION
-int  soft_serial_transaction(void);
-#else
-int  soft_serial_transaction(int sstd_index);
-#endif
-
-// target status
-// *SSTD_t.status has
-//   initiator:
-//       TRANSACTION_END
-//    or TRANSACTION_NO_RESPONSE
-//    or TRANSACTION_DATA_ERROR
-//   target:
-//       TRANSACTION_DATA_ERROR
-//    or TRANSACTION_ACCEPTED
-#define TRANSACTION_ACCEPTED 0x8
-#ifdef SERIAL_USE_MULTI_TRANSACTION
-int  soft_serial_get_and_clean_status(int sstd_index);
-#endif
diff --git a/keyboards/helix/local_drivers/ssd1306.c b/keyboards/helix/local_drivers/ssd1306.c
deleted file mode 100644
index 1cfb38037c..0000000000
--- a/keyboards/helix/local_drivers/ssd1306.c
+++ /dev/null
@@ -1,341 +0,0 @@
-
-#ifdef SSD1306OLED
-
-#include "ssd1306.h"
-#include "i2c.h"
-#include <string.h>
-#include "print.h"
-#ifndef LOCAL_GLCDFONT
-#include "common/glcdfont.c"
-#else
-#include "helixfont.h"
-#endif
-#ifdef PROTOCOL_LUFA
-#include "lufa.h"
-#endif
-#include "sendchar.h"
-#include "timer.h"
-
-struct CharacterMatrix display;
-
-// Set this to 1 to help diagnose early startup problems
-// when testing power-on with ble.  Turn it off otherwise,
-// as the latency of printing most of the debug info messes
-// with the matrix scan, causing keys to drop.
-#define DEBUG_TO_SCREEN 0
-
-//static uint16_t last_battery_update;
-//static uint32_t vbat;
-//#define BatteryUpdateInterval 10000 /* milliseconds */
-
-// 'last_flush' is declared as uint16_t,
-// so this must be less than 65535 
-#define ScreenOffInterval 60000 /* milliseconds */
-#if DEBUG_TO_SCREEN
-static uint8_t displaying;
-#endif
-static uint16_t last_flush;
-
-static bool force_dirty = true;
-
-// Write command sequence.
-// Returns true on success.
-static inline bool _send_cmd1(uint8_t cmd) {
-  bool res = false;
-
-  if (i2c_start_write(SSD1306_ADDRESS)) {
-    xprintf("failed to start write to %d\n", SSD1306_ADDRESS);
-    goto done;
-  }
-
-  if (i2c_master_write(0x0 /* command byte follows */)) {
-    print("failed to write control byte\n");
-
-    goto done;
-  }
-
-  if (i2c_master_write(cmd)) {
-    xprintf("failed to write command %d\n", cmd);
-    goto done;
-  }
-  res = true;
-done:
-  i2c_master_stop();
-  return res;
-}
-
-// Write 2-byte command sequence.
-// Returns true on success
-static inline bool _send_cmd2(uint8_t cmd, uint8_t opr) {
-  if (!_send_cmd1(cmd)) {
-    return false;
-  }
-  return _send_cmd1(opr);
-}
-
-// Write 3-byte command sequence.
-// Returns true on success
-static inline bool _send_cmd3(uint8_t cmd, uint8_t opr1, uint8_t opr2) {
-  if (!_send_cmd1(cmd)) {
-    return false;
-  }
-  if (!_send_cmd1(opr1)) {
-    return false;
-  }
-  return _send_cmd1(opr2);
-}
-
-#define send_cmd1(c) if (!_send_cmd1(c)) {goto done;}
-#define send_cmd2(c,o) if (!_send_cmd2(c,o)) {goto done;}
-#define send_cmd3(c,o1,o2) if (!_send_cmd3(c,o1,o2)) {goto done;}
-
-static void clear_display(void) {
-  matrix_clear(&display);
-