Merge pull request #1263 from Dbroqua/master

Fixed bugs for S60-X RGB version

2 files changed, 16 insertions, 56 deletions

diff --git a/keyboards/s60-x/rgb/config.h b/keyboards/s60-x/rgb/config.h
index 26b246e573..fbc143487e 100644
--- a/keyboards/s60-x/rgb/config.h
+++ b/keyboards/s60-x/rgb/config.h
@@ -9,6 +9,7 @@
 /* key matrix pins */
 #define MATRIX_ROW_PINS { B5, B4, D7, D6, D4 }
 #define MATRIX_COL_PINS { D0, D1, D2, D3, D5, B6, C6, C7, F1, F0, E6, B3, B2, B1, B0 }
+#define UNUSED_PINS
 
 /* number of backlight levels */
 #define BACKLIGHT_PIN B7
@@ -16,6 +17,12 @@
 #define BACKLIGHT_LEVELS 3
 #endif
 
+/* Mechanical locking support. Use KC_LCAP, KC_LNUM or KC_LSCR instead in keymap */
+#define LOCKING_SUPPORT_ENABLE
+
+/* Locking resynchronize hack */
+#define LOCKING_RESYNC_ENABLE
+
 /* prevent stuck modifiers */
 #define PREVENT_STUCK_MODIFIERS
 
diff --git a/keyboards/s60-x/rgb/rules.mk b/keyboards/s60-x/rgb/rules.mk
index c303af4bcc..6953cc6d6d 100644
--- a/keyboards/s60-x/rgb/rules.mk
+++ b/keyboards/s60-x/rgb/rules.mk
@@ -1,56 +1,9 @@
-# MCU name
-MCU = atmega32u4
-
-# Processor frequency.
-#     This will define a symbol, F_CPU, in all source code files equal to the
-#     processor frequency in Hz. You can then use this symbol in your source code to
-#     calculate timings. Do NOT tack on a 'UL' at the end, this will be done
-#     automatically to create a 32-bit value in your source code.
-#
-#     This will be an integer division of F_USB below, as it is sourced by
-#     F_USB after it has run through any CPU prescalers. Note that this value
-#     does not *change* the processor frequency - it should merely be updated to
-#     reflect the processor speed set externally so that the code can use accurate
-#     software delays.
-F_CPU = 16000000
-
-#
-# LUFA specific
-#
-# Target architecture (see library "Board Types" documentation).
-ARCH = AVR8
-
-# Input clock frequency.
-#     This will define a symbol, F_USB, in all source code files equal to the
-#     input clock frequency (before any prescaling is performed) in Hz. This value may
-#     differ from F_CPU if prescaling is used on the latter, and is required as the
-#     raw input clock is fed directly to the PLL sections of the AVR for high speed
-#     clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
-#     at the end, this will be done automatically to create a 32-bit value in your
-#     source code.
-#
-#     If no clock division is performed on the input clock inside the AVR (via the
-#     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
-F_USB = $(F_CPU)
-
-# Interrupt driven control endpoint task(+60)
-OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
-
-
-# Boot Section Size in *bytes*
-OPT_DEFS += -DBOOTLOADER_SIZE=4096
-
-
-# Build Options
-#   comment out to disable the options.
-#
-BOOTMAGIC_ENABLE ?= yes	# Virtual DIP switch configuration(+1000)
-MOUSEKEY_ENABLE ?= yes	# Mouse keys(+4700)
-EXTRAKEY_ENABLE ?= yes	# Audio control and System control(+450)
-CONSOLE_ENABLE ?= no	# Console for debug(+400)
-COMMAND_ENABLE ?= no    # Commands for debug and configuration
-SLEEP_LED_ENABLE ?= no  # Breathing sleep LED during USB suspend
-NKRO_ENABLE ?= yes		# USB Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
-BACKLIGHT_ENABLE ?= yes  # Enable keyboard backlight functionality
-AUDIO_ENABLE ?= no
-RGBLIGHT_ENABLE ?= yes
\ No newline at end of file
+CONSOLE_ENABLE ?= no        # Console for debug(+400)
+COMMAND_ENABLE ?= no        # Commands for debug and configuration
+NKRO_ENABLE ?= yes          # USB Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
+BACKLIGHT_ENABLE ?= yes     # Enable keyboard backlight functionality
+RGBLIGHT_ENABLE ?= yes      # Enable RGB light
+
+ifndef QUANTUM_DIR
+	include ../../../Makefile
+endif
\ No newline at end of file