Merge branch 'master' of http://github.com/jackhumbert/qmk_firmware

3 files changed, 107 insertions, 108 deletions

diff --git a/keyboards/lets_split/Makefile b/keyboards/lets_split/Makefile
index b9f07636be..4e2a6f00fd 100644
--- a/keyboards/lets_split/Makefile
+++ b/keyboards/lets_split/Makefile
@@ -1,78 +1,3 @@
-SRC += matrix.c \
-	   i2c.c \
-	   split_util.c \
-	   serial.c
-
-# MCU name
-#MCU = at90usb1287
-MCU = atmega32u4
-
-# Processor frequency.
-#     This will define a symbol, F_CPU, in all source code files equal to the
-#     processor frequency in Hz. You can then use this symbol in your source code to
-#     calculate timings. Do NOT tack on a 'UL' at the end, this will be done
-#     automatically to create a 32-bit value in your source code.
-#
-#     This will be an integer division of F_USB below, as it is sourced by
-#     F_USB after it has run through any CPU prescalers. Note that this value
-#     does not *change* the processor frequency - it should merely be updated to
-#     reflect the processor speed set externally so that the code can use accurate
-#     software delays.
-F_CPU = 16000000
-
-#
-# LUFA specific
-#
-# Target architecture (see library "Board Types" documentation).
-ARCH = AVR8
-
-# Input clock frequency.
-#     This will define a symbol, F_USB, in all source code files equal to the
-#     input clock frequency (before any prescaling is performed) in Hz. This value may
-#     differ from F_CPU if prescaling is used on the latter, and is required as the
-#     raw input clock is fed directly to the PLL sections of the AVR for high speed
-#     clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
-#     at the end, this will be done automatically to create a 32-bit value in your
-#     source code.
-#
-#     If no clock division is performed on the input clock inside the AVR (via the
-#     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
-F_USB = $(F_CPU)
-
-# Interrupt driven control endpoint task(+60)
-OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
-
-
-# Boot Section Size in *bytes*
-#   Teensy halfKay   512
-#   Teensy++ halfKay 1024
-#   Atmel DFU loader 4096
-#   LUFA bootloader  4096
-#   USBaspLoader     2048
-OPT_DEFS += -DBOOTLOADER_SIZE=4096
-
-# Build Options
-#   change to "no" to disable the options, or define them in the Makefile in 
-#   the appropriate keymap folder that will get included automatically
-#
-BOOTMAGIC_ENABLE ?= no       # Virtual DIP switch configuration(+1000)
-MOUSEKEY_ENABLE ?= yes       # Mouse keys(+4700)
-EXTRAKEY_ENABLE ?= yes       # Audio control and System control(+450)
-CONSOLE_ENABLE ?= no         # Console for debug(+400)
-COMMAND_ENABLE ?= yes        # Commands for debug and configuration
-NKRO_ENABLE ?= no            # Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
-BACKLIGHT_ENABLE ?= no      # Enable keyboard backlight functionality
-MIDI_ENABLE ?= no            # MIDI controls
-AUDIO_ENABLE ?= yes           # Audio output on port C6
-UNICODE_ENABLE ?= no         # Unicode
-BLUETOOTH_ENABLE ?= no       # Enable Bluetooth with the Adafruit EZ-Key HID
-RGBLIGHT_ENABLE ?= no        # Enable WS2812 RGB underlight.  Do not enable this with audio at the same time.
-
-# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE
-SLEEP_LED_ENABLE ?= no    # Breathing sleep LED during USB suspend
-
-CUSTOM_MATRIX = yes
-
-ifndef QUANTUM_DIR
+ifndef MAKEFILE_INCLUDED
 	include ../../Makefile
 endif
\ No newline at end of file
diff --git a/keyboards/lets_split/pro_micro.h b/keyboards/lets_split/pro_micro.h
index 09e219b7b1..f9e7ed75d9 100644
--- a/keyboards/lets_split/pro_micro.h
+++ b/keyboards/lets_split/pro_micro.h
@@ -111,18 +111,18 @@ static const uint8_t SCK  = 15;
 
 // Mapping of analog pins as digital I/O
 // A6-A11 share with digital pins
-static const uint8_t A0 = 18;
-static const uint8_t A1 = 19;
-static const uint8_t A2 = 20;
-static const uint8_t A3 = 21;
-static const uint8_t A4 = 22;
-static const uint8_t A5 = 23;
-static const uint8_t A6 = 24;   // D4
-static const uint8_t A7 = 25;   // D6
-static const uint8_t A8 = 26;   // D8
-static const uint8_t A9 = 27;   // D9
-static const uint8_t A10 = 28;  // D10
-static const uint8_t A11 = 29;  // D12
+static const uint8_t ADC0 = 18;
+static const uint8_t ADC1 = 19;
+static const uint8_t ADC2 = 20;
+static const uint8_t ADC3 = 21;
+static const uint8_t ADC4 = 22;
+static const uint8_t ADC5 = 23;
+static const uint8_t ADC6 = 24;   // D4
+static const uint8_t ADC7 = 25;   // D6
+static const uint8_t ADC8 = 26;   // D8
+static const uint8_t ADC9 = 27;   // D9
+static const uint8_t ADC10 = 28;  // D10
+static const uint8_t ADC11 = 29;  // D12
 
 #define digitalPinToPCICR(p)    ((((p) >= 8 && (p) <= 11) || ((p) >= 14 && (p) <= 17) || ((p) >= A8 && (p) <= A10)) ? (&PCICR) : ((uint8_t *)0))
 #define digitalPinToPCICRbit(p) 0
@@ -220,26 +220,26 @@ const uint8_t PROGMEM digital_pin_to_port_PGM[] = {
     PC, // D5 - PC6
     PD, // D6 - PD7
     PE, // D7 - PE6
-    
+
     PB, // D8 - PB4
     PB, // D9 - PB5
     PB, // D10 - PB6
     PB, // D11 - PB7
     PD, // D12 - PD6
     PC, // D13 - PC7
-    
+
     PB, // D14 - MISO - PB3
     PB, // D15 - SCK - PB1
     PB, // D16 - MOSI - PB2
     PB, // D17 - SS - PB0
-    
+
     PF, // D18 - A0 - PF7
     PF, // D19 - A1 - PF6
     PF, // D20 - A2 - PF5
     PF, // D21 - A3 - PF4
     PF, // D22 - A4 - PF1
     PF, // D23 - A5 - PF0
-    
+
     PD, // D24 - PD5
     PD, // D25 / D6 - A7 - PD7
     PB, // D26 / D8 - A8 - PB4
@@ -257,26 +257,26 @@ const uint8_t PROGMEM digital_pin_to_bit_mask_PGM[] = {
     _BV(6), // D5 - PC6
     _BV(7), // D6 - PD7
     _BV(6), // D7 - PE6
-    
+
     _BV(4), // D8 - PB4
     _BV(5), // D9 - PB5
     _BV(6), // D10 - PB6
     _BV(7), // D11 - PB7
     _BV(6), // D12 - PD6
     _BV(7), // D13 - PC7
-    
+
     _BV(3), // D14 - MISO - PB3
     _BV(1), // D15 - SCK - PB1
     _BV(2), // D16 - MOSI - PB2
     _BV(0), // D17 - SS - PB0
-    
+
     _BV(7), // D18 - A0 - PF7
     _BV(6), // D19 - A1 - PF6
     _BV(5), // D20 - A2 - PF5
     _BV(4), // D21 - A3 - PF4
     _BV(1), // D22 - A4 - PF1
     _BV(0), // D23 - A5 - PF0
-    
+
     _BV(5), // D24 - PD5
     _BV(7), // D25 / D6 - A7 - PD7
     _BV(4), // D26 / D8 - A8 - PB4
@@ -286,24 +286,24 @@ const uint8_t PROGMEM digital_pin_to_bit_mask_PGM[] = {
 };
 
 const uint8_t PROGMEM digital_pin_to_timer_PGM[] = {
-    NOT_ON_TIMER,   
+    NOT_ON_TIMER,
     NOT_ON_TIMER,
     NOT_ON_TIMER,
     TIMER0B,        /* 3 */
     NOT_ON_TIMER,
     TIMER3A,        /* 5 */
     TIMER4D,        /* 6 */
-    NOT_ON_TIMER,   
-    
-    NOT_ON_TIMER,   
+    NOT_ON_TIMER,
+
+    NOT_ON_TIMER,
     TIMER1A,        /* 9 */
     TIMER1B,        /* 10 */
     TIMER0A,        /* 11 */
-    
-    NOT_ON_TIMER,   
+
+    NOT_ON_TIMER,
     TIMER4A,        /* 13 */
-    
-    NOT_ON_TIMER,   
+
+    NOT_ON_TIMER,
     NOT_ON_TIMER,
     NOT_ON_TIMER,
     NOT_ON_TIMER,
@@ -324,11 +324,11 @@ const uint8_t PROGMEM digital_pin_to_timer_PGM[] = {
 
 const uint8_t PROGMEM analog_pin_to_channel_PGM[] = {
     7,  // A0               PF7                 ADC7
-    6,  // A1               PF6                 ADC6    
-    5,  // A2               PF5                 ADC5    
+    6,  // A1               PF6                 ADC6
+    5,  // A2               PF5                 ADC5
     4,  // A3               PF4                 ADC4
-    1,  // A4               PF1                 ADC1    
-    0,  // A5               PF0                 ADC0    
+    1,  // A4               PF1                 ADC1
+    0,  // A5               PF0                 ADC0
     8,  // A6       D4      PD4                 ADC8
     10, // A7       D6      PD7                 ADC10
     11, // A8       D8      PB4                 ADC11
diff --git a/keyboards/lets_split/rules.mk b/keyboards/lets_split/rules.mk
new file mode 100644
index 0000000000..6961fbd556
--- /dev/null
+++ b/keyboards/lets_split/rules.mk
@@ -0,0 +1,74 @@
+SRC += matrix.c \
+	   i2c.c \
+	   split_util.c \
+	   serial.c
+
+# MCU name
+#MCU = at90usb1287
+MCU = atmega32u4
+
+# Processor frequency.
+#     This will define a symbol, F_CPU, in all source code files equal to the
+#     processor frequency in Hz. You can then use this symbol in your source code to
+#     calculate timings. Do NOT tack on a 'UL' at the end, this will be done
+#     automatically to create a 32-bit value in your source code.
+#
+#     This will be an integer division of F_USB below, as it is sourced by
+#     F_USB after it has run through any CPU prescalers. Note that this value
+#     does not *change* the processor frequency - it should merely be updated to
+#     reflect the processor speed set externally so that the code can use accurate
+#     software delays.
+F_CPU = 16000000
+
+#
+# LUFA specific
+#
+# Target architecture (see library "Board Types" documentation).
+ARCH = AVR8
+
+# Input clock frequency.
+#     This will define a symbol, F_USB, in all source code files equal to the
+#     input clock frequency (before any prescaling is performed) in Hz. This value may
+#     differ from F_CPU if prescaling is used on the latter, and is required as the
+#     raw input clock is fed directly to the PLL sections of the AVR for high speed
+#     clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
+#     at the end, this will be done automatically to create a 32-bit value in your
+#     source code.
+#
+#     If no clock division is performed on the input clock inside the AVR (via the
+#     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
+F_USB = $(F_CPU)
+
+# Interrupt driven control endpoint task(+60)
+OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
+
+
+# Boot Section Size in *bytes*
+#   Teensy halfKay   512
+#   Teensy++ halfKay 1024
+#   Atmel DFU loader 4096
+#   LUFA bootloader  4096
+#   USBaspLoader     2048
+OPT_DEFS += -DBOOTLOADER_SIZE=4096
+
+# Build Options
+#   change to "no" to disable the options, or define them in the Makefile in 
+#   the appropriate keymap folder that will get included automatically
+#
+BOOTMAGIC_ENABLE ?= no       # Virtual DIP switch configuration(+1000)
+MOUSEKEY_ENABLE ?= yes       # Mouse keys(+4700)
+EXTRAKEY_ENABLE ?= yes       # Audio control and System control(+450)
+CONSOLE_ENABLE ?= no         # Console for debug(+400)
+COMMAND_ENABLE ?= yes        # Commands for debug and configuration
+NKRO_ENABLE ?= no            # Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
+BACKLIGHT_ENABLE ?= no      # Enable keyboard backlight functionality
+MIDI_ENABLE ?= no            # MIDI controls
+AUDIO_ENABLE ?= yes           # Audio output on port C6
+UNICODE_ENABLE ?= no         # Unicode
+BLUETOOTH_ENABLE ?= no       # Enable Bluetooth with the Adafruit EZ-Key HID
+RGBLIGHT_ENABLE ?= no        # Enable WS2812 RGB underlight.  Do not enable this with audio at the same time.
+
+# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE
+SLEEP_LED_ENABLE ?= no    # Breathing sleep LED during USB suspend
+
+CUSTOM_MATRIX = yes
\ No newline at end of file