Merge branch 'master' of https://github.com/jackhumbert/qmk_firmware

1 files changed, 86 insertions, 0 deletions

diff --git a/keyboards/ergodox_ez/Makefile b/keyboards/ergodox_ez/Makefile
new file mode 100644
index 0000000000..54edaed6d1
--- /dev/null
+++ b/keyboards/ergodox_ez/Makefile
@@ -0,0 +1,86 @@
+#----------------------------------------------------------------------------
+# On command line:
+#
+# make = Make software.
+#
+# make clean = Clean out built project files.
+#
+# That's pretty much all you need. To compile, always go make clean, 
+# followed by make.
+#
+# For advanced users only:
+# make teensy = Download the hex file to the device, using teensy_loader_cli.
+#               (must have teensy_loader_cli installed).
+#
+#----------------------------------------------------------------------------
+
+# # project specific files
+SRC = twimaster.c \
+	  matrix.c
+
+# MCU name
+MCU = atmega32u4
+
+# Processor frequency.
+#     This will define a symbol, F_CPU, in all source code files equal to the
+#     processor frequency in Hz. You can then use this symbol in your source code to
+#     calculate timings. Do NOT tack on a 'UL' at the end, this will be done
+#     automatically to create a 32-bit value in your source code.
+#
+#     This will be an integer division of F_USB below, as it is sourced by
+#     F_USB after it has run through any CPU prescalers. Note that this value
+#     does not *change* the processor frequency - it should merely be updated to
+#     reflect the processor speed set externally so that the code can use accurate
+#     software delays.
+F_CPU = 16000000
+
+
+#
+# LUFA specific
+#
+# Target architecture (see library "Board Types" documentation).
+ARCH = AVR8
+
+# Input clock frequency.
+#     This will define a symbol, F_USB, in all source code files equal to the
+#     input clock frequency (before any prescaling is performed) in Hz. This value may
+#     differ from F_CPU if prescaling is used on the latter, and is required as the
+#     raw input clock is fed directly to the PLL sections of the AVR for high speed
+#     clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
+#     at the end, this will be done automatically to create a 32-bit value in your
+#     source code.
+#
+#     If no clock division is performed on the input clock inside the AVR (via the
+#     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
+F_USB = $(F_CPU)
+
+# Interrupt driven control endpoint task(+60)
+OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
+
+
+# Boot Section Size in *bytes*
+#   Teensy halfKay   512
+#   Teensy++ halfKay 1024
+#   Atmel DFU loader 4096
+#   LUFA bootloader  4096
+#   USBaspLoader     2048
+OPT_DEFS += -DBOOTLOADER_SIZE=512
+
+
+# Build Options
+#   comment out to disable the options.
+#
+BOOTMAGIC_ENABLE ?= no  # Virtual DIP switch configuration(+1000)
+MOUSEKEY_ENABLE  ?= yes # Mouse keys(+4700)
+EXTRAKEY_ENABLE  ?= yes # Audio control and System control(+450)
+CONSOLE_ENABLE   ?= no  # Console for debug(+400)
+COMMAND_ENABLE   ?= yes # Commands for debug and configuration
+CUSTOM_MATRIX    ?= yes # Custom matrix file for the ErgoDox EZ
+SLEEP_LED_ENABLE ?= yes # Breathing sleep LED during USB suspend
+NKRO_ENABLE      ?= yes # USB Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
+MIDI_ENABLE      ?= no  # MIDI controls
+UNICODE_ENABLE   ?= yes # Unicode
+
+ifndef QUANTUM_DIR
+	include ../../Makefile
+endif