Move ChibiOS test board and ld

Move the ChibiOS test subproject board and ld files to the kebyoard
folder, so that the build system can find them

4 files changed, 220 insertions, 0 deletions

diff --git a/keyboards/chibios_test/boards/GENERIC_STM32_F103/board.c b/keyboards/chibios_test/boards/GENERIC_STM32_F103/board.c
new file mode 100644
index 0000000000..31319ef575
--- /dev/null
+++ b/keyboards/chibios_test/boards/GENERIC_STM32_F103/board.c
@@ -0,0 +1,49 @@
+/*

+    ChibiOS - Copyright (C) 2006..2015 Giovanni Di Sirio

+

+    Licensed under the Apache License, Version 2.0 (the "License");

+    you may not use this file except in compliance with the License.

+    You may obtain a copy of the License at

+

+        http://www.apache.org/licenses/LICENSE-2.0

+

+    Unless required by applicable law or agreed to in writing, software

+    distributed under the License is distributed on an "AS IS" BASIS,

+    WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.

+    See the License for the specific language governing permissions and

+    limitations under the License.

+*/

+

+#include "hal.h"

+

+/**

+ * @brief   PAL setup.

+ * @details Digital I/O ports static configuration as defined in @p board.h.

+ *          This variable is used by the HAL when initializing the PAL driver.

+ */

+#if HAL_USE_PAL || defined(__DOXYGEN__)

+const PALConfig pal_default_config =

+{

+  {VAL_GPIOAODR, VAL_GPIOACRL, VAL_GPIOACRH},

+  {VAL_GPIOBODR, VAL_GPIOBCRL, VAL_GPIOBCRH},

+  {VAL_GPIOCODR, VAL_GPIOCCRL, VAL_GPIOCCRH},

+  {VAL_GPIODODR, VAL_GPIODCRL, VAL_GPIODCRH},

+  {VAL_GPIOEODR, VAL_GPIOECRL, VAL_GPIOECRH},

+};

+#endif

+

+/*

+ * Early initialization code.

+ * This initialization must be performed just after stack setup and before

+ * any other initialization.

+ */

+void __early_init(void) {

+

+  stm32_clock_init();

+}

+

+/*

+ * Board-specific initialization code.

+ */

+void boardInit(void) {

+}

diff --git a/keyboards/chibios_test/boards/GENERIC_STM32_F103/board.h b/keyboards/chibios_test/boards/GENERIC_STM32_F103/board.h
new file mode 100644
index 0000000000..7253e77826
--- /dev/null
+++ b/keyboards/chibios_test/boards/GENERIC_STM32_F103/board.h
@@ -0,0 +1,166 @@
+/*

+    ChibiOS - Copyright (C) 2006..2015 Giovanni Di Sirio

+

+    Licensed under the Apache License, Version 2.0 (the "License");

+    you may not use this file except in compliance with the License.

+    You may obtain a copy of the License at

+

+        http://www.apache.org/licenses/LICENSE-2.0

+

+    Unless required by applicable law or agreed to in writing, software

+    distributed under the License is distributed on an "AS IS" BASIS,

+    WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.

+    See the License for the specific language governing permissions and

+    limitations under the License.

+*/

+

+#ifndef _BOARD_H_

+#define _BOARD_H_

+

+/*

+ * Setup for a Generic STM32F103 board.

+ */

+

+/*

+ * Board identifier.

+ */

+#define BOARD_GENERIC_STM32_F103

+#define BOARD_NAME              "Generic STM32F103x board"

+

+/*

+ * Board frequencies.

+ */

+#define STM32_LSECLK            32768

+#define STM32_HSECLK            8000000

+

+/*

+ * MCU type, supported types are defined in ./os/hal/platforms/hal_lld.h.

+ */

+#define STM32F103xB

+

+/*

+ * IO pins assignments

+ */

+

+/* on-board */

+

+#define GPIOC_LED               13

+#define GPIOD_OSC_IN            0

+#define GPIOD_OSC_OUT           1

+

+/* In case your board has a "USB enable" hardware

+   controlled by a pin, define it here. (It could be just

+   a 1.5k resistor connected to D+ line.)

+*/

+/*

+#define GPIOB_USB_DISC          10

+*/

+

+/*

+ * I/O ports initial setup, this configuration is established soon after reset

+ * in the initialization code.

+ *

+ * The digits have the following meaning:

+ *   0 - Analog input.

+ *   1 - Push Pull output 10MHz.

+ *   2 - Push Pull output 2MHz.

+ *   3 - Push Pull output 50MHz.

+ *   4 - Digital input.

+ *   5 - Open Drain output 10MHz.

+ *   6 - Open Drain output 2MHz.

+ *   7 - Open Drain output 50MHz.

+ *   8 - Digital input with PullUp or PullDown resistor depending on ODR.

+ *   9 - Alternate Push Pull output 10MHz.

+ *   A - Alternate Push Pull output 2MHz.

+ *   B - Alternate Push Pull output 50MHz.

+ *   C - Reserved.

+ *   D - Alternate Open Drain output 10MHz.

+ *   E - Alternate Open Drain output 2MHz.

+ *   F - Alternate Open Drain output 50MHz.

+ * Please refer to the STM32 Reference Manual for details.

+ */

+

+/*

+ * Port A setup.

+ * Everything input with pull-up except:

+ * PA2  - Alternate output  (USART2 TX).

+ * PA3  - Normal input      (USART2 RX).

+ * PA9  - Alternate output  (USART1 TX).

+ * PA10 - Normal input      (USART1 RX).

+ */

+#define VAL_GPIOACRL            0x88884B88      /*  PA7...PA0 */

+#define VAL_GPIOACRH            0x888884B8      /* PA15...PA8 */

+#define VAL_GPIOAODR            0xFFFFFFFF

+

+/*

+ * Port B setup.

+ * Everything input with pull-up except:

+ * PB10    - Push Pull output  (USB switch).

+ */

+#define VAL_GPIOBCRL            0x88888888      /*  PB7...PB0 */

+#define VAL_GPIOBCRH            0x88888388      /* PB15...PB8 */

+#define VAL_GPIOBODR            0xFFFFFFFF

+

+/*

+ * Port C setup.

+ * Everything input with pull-up except:

+ * PC13    - Push Pull output  (LED).

+ */

+#define VAL_GPIOCCRL            0x88888888      /*  PC7...PC0 */

+#define VAL_GPIOCCRH            0x88388888      /* PC15...PC8 */

+#define VAL_GPIOCODR            0xFFFFFFFF

+

+/*

+ * Port D setup.

+ * Everything input with pull-up except:

+ * PD0  - Normal input (XTAL).

+ * PD1  - Normal input (XTAL).

+ */

+#define VAL_GPIODCRL            0x88888844      /*  PD7...PD0 */

+#define VAL_GPIODCRH            0x88888888      /* PD15...PD8 */

+#define VAL_GPIODODR            0xFFFFFFFF

+

+/*

+ * Port E setup.

+ * Everything input with pull-up except:

+ */

+#define VAL_GPIOECRL            0x88888888      /*  PE7...PE0 */

+#define VAL_GPIOECRH            0x88888888      /* PE15...PE8 */

+#define VAL_GPIOEODR            0xFFFFFFFF

+

+/*

+ * USB bus activation macro, required by the USB driver.

+ */

+/* The point is that most of the generic STM32F103* boards

+   have a 1.5k resistor connected on one end to the D+ line

+   and on the other end to some pin. Or even a slightly more

+   complicated "USB enable" circuit, controlled by a pin.

+   That should go here.

+

+   However on some boards (e.g. one that I have), there's no

+   such hardware. In which case it's better to not do anything.

+*/

+/*

+#define usb_lld_connect_bus(usbp) palClearPad(GPIOB, GPIOB_USB_DISC)

+*/

+#define usb_lld_connect_bus(usbp) palSetPadMode(GPIOA, 12, PAL_MODE_INPUT);

+

+/*

+ * USB bus de-activation macro, required by the USB driver.

+ */

+/*

+#define usb_lld_disconnect_bus(usbp) palSetPad(GPIOB, GPIOB_USB_DISC)

+*/

+#define usb_lld_disconnect_bus(usbp) palSetPadMode(GPIOA, 12, PAL_MODE_OUTPUT_PUSHPULL); palClearPad(GPIOA, 12);

+

+#if !defined(_FROM_ASM_)

+#ifdef __cplusplus

+extern "C" {

+#endif

+  void boardInit(void);

+#ifdef __cplusplus

+}

+#endif

+#endif /* _FROM_ASM_ */

+

+#endif /* _BOARD_H_ */

diff --git a/keyboards/chibios_test/boards/GENERIC_STM32_F103/board.mk b/keyboards/chibios_test/boards/GENERIC_STM32_F103/board.mk
new file mode 100644
index 0000000000..d692c0ee46
--- /dev/null
+++ b/keyboards/chibios_test/boards/GENERIC_STM32_F103/board.mk
@@ -0,0 +1,5 @@
+# List of all the board related files.

+BOARDSRC = $(KEYBOARD_PATH)/boards/GENERIC_STM32_F103/board.c

+

+# Required include directories

+BOARDINC = $(KEYBOARD_PATH)/boards/GENERIC_STM32_F103

diff --git a/keyboards/chibios_test/boards/GENERIC_STM32_F103/mini_stm32_mapping.png b/keyboards/chibios_test/boards/GENERIC_STM32_F103/mini_stm32_mapping.png
new file mode 100644
index 0000000000..c44a7d9ebc
--- /dev/null
+++ b/keyboards/chibios_test/boards/GENERIC_STM32_F103/mini_stm32_mapping.png