Merge remote-tracking branch 'upstream/master'

39 files changed, 735 insertions, 882 deletions

diff --git a/keyboards/40percentclub/25/rules.mk b/keyboards/40percentclub/25/rules.mk
index bfcdce7c99..3321a84025 100644
--- a/keyboards/40percentclub/25/rules.mk
+++ b/keyboards/40percentclub/25/rules.mk
@@ -1,63 +1,16 @@
 # MCU name
 MCU = atmega32u4
 
-# Processor frequency.
-#     This will define a symbol, F_CPU, in all source code files equal to the
-#     processor frequency in Hz. You can then use this symbol in your source code to
-#     calculate timings. Do NOT tack on a 'UL' at the end, this will be done
-#     automatically to create a 32-bit value in your source code.
-#
-#     This will be an integer division of F_USB below, as it is sourced by
-#     F_USB after it has run through any CPU prescalers. Note that this value
-#     does not *change* the processor frequency - it should merely be updated to
-#     reflect the processor speed set externally so that the code can use accurate
-#     software delays.
-F_CPU = 16000000
-
-
-#
-# LUFA specific
-#
-# Target architecture (see library "Board Types" documentation).
-ARCH = AVR8
-
-# Input clock frequency.
-#     This will define a symbol, F_USB, in all source code files equal to the
-#     input clock frequency (before any prescaling is performed) in Hz. This value may
-#     differ from F_CPU if prescaling is used on the latter, and is required as the
-#     raw input clock is fed directly to the PLL sections of the AVR for high speed
-#     clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
-#     at the end, this will be done automatically to create a 32-bit value in your
-#     source code.
-#
-#     If no clock division is performed on the input clock inside the AVR (via the
-#     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
-F_USB = $(F_CPU)
-
-# Interrupt driven control endpoint task(+60)
-OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
-
-
 # Bootloader selection
 #   Teensy       halfkay
 #   Pro Micro    caterina
 #   Atmel DFU    atmel-dfu
 #   LUFA DFU     lufa-dfu
 #   QMK DFU      qmk-dfu
-#   atmega32a    bootloadHID
+#   ATmega32A    bootloadHID
+#   ATmega328P   USBasp
 BOOTLOADER = caterina
 
-
-# If you don't know the bootloader type, then you can specify the
-# Boot Section Size in *bytes* by uncommenting out the OPT_DEFS line
-#   Teensy halfKay      512
-#   Teensy++ halfKay    1024
-#   Atmel DFU loader    4096
-#   LUFA bootloader     4096
-#   USBaspLoader        2048
-# OPT_DEFS += -DBOOTLOADER_SIZE=4096
-
-
 # Build Options
 #   change yes to no to disable
 #
diff --git a/keyboards/40percentclub/4pack/4pack.c b/keyboards/40percentclub/4pack/4pack.c
new file mode 100644
index 0000000000..98f22a65a5
--- /dev/null
+++ b/keyboards/40percentclub/4pack/4pack.c
@@ -0,0 +1,54 @@
+/* Copyright 2019 Arda Kilicdagi
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+#include "4pack.h"
+
+// Optional override functions below.
+// You can leave any or all of these undefined.
+// These are only required if you want to perform custom actions.
+
+void matrix_init_kb(void) {
+  // put your keyboard start-up code here
+  // runs once when the firmware starts up
+
+  setPinOutput(F4); // cathodes
+  setPinOutput(F5); // cathodes
+
+  // Do the rest
+  matrix_init_user();
+}
+
+/*
+void matrix_scan_kb(void) {
+  // put your looping keyboard code here
+  // runs every cycle (a lot)
+
+  matrix_scan_user();
+}
+
+bool process_record_kb(uint16_t keycode, keyrecord_t *record) {
+  // put your per-action keyboard code here
+  // runs for every action, just before processing by the firmware
+
+  return process_record_user(keycode, record);
+}
+
+void led_set_kb(uint8_t usb_led) {
+  // put your keyboard LED indicator (ex: Caps Lock LED) toggling code here
+
+  led_set_user(usb_led);
+}
+
+*/
diff --git a/keyboards/40percentclub/4pack/4pack.h b/keyboards/40percentclub/4pack/4pack.h
new file mode 100644
index 0000000000..1340300ace
--- /dev/null
+++ b/keyboards/40percentclub/4pack/4pack.h
@@ -0,0 +1,33 @@
+/* Copyright 2019 Arda Kilicdagi
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+#pragma once
+
+#include "quantum.h"
+
+/* This a shortcut to help you visually see your layout.
+ *
+ * The first section contains all of the arguments representing the physical
+ * layout of the board and position of the keys.
+ *
+ * The second converts the arguments into a two-dimensional array which
+ * represents the switch matrix.
+ */
+#define LAYOUT( \
+    k00, k01, k02, k03 \
+) \
+{ \
+    { k00, k01, k02, k03 }, \
+}
diff --git a/keyboards/40percentclub/4pack/config.h b/keyboards/40percentclub/4pack/config.h
new file mode 100644
index 0000000000..33b5df6d58
--- /dev/null
+++ b/keyboards/40percentclub/4pack/config.h
@@ -0,0 +1,257 @@
+/*
+Copyright 2019 Arda Kilicdagi
+
+This program is free software: you can redistribute it and/or modify
+it under the terms of the GNU General Public License as published by
+the Free Software Foundation, either version 2 of the License, or
+(at your option) any later version.
+
+This program is distributed in the hope that it will be useful,
+but WITHOUT ANY WARRANTY; without even the implied warranty of
+MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+GNU General Public License for more details.
+
+You should have received a copy of the GNU General Public License
+along with this program.  If not, see <http://www.gnu.org/licenses/>.
+*/
+
+#pragma once
+
+#include "config_common.h"
+
+/* USB Device descriptor parameter */
+#define VENDOR_ID 0xFEED
+#define PRODUCT_ID 0x0000
+#define DEVICE_VER 0x0001
+#define MANUFACTURER 40percentclub
+#define PRODUCT 4pack
+#define DESCRIPTION A 1x4 custom macropad
+
+/* key matrix size */
+#define MATRIX_ROWS 1
+#define MATRIX_COLS 4
+
+/*
+ * Keyboard Matrix Assignments
+ *
+ * Change this to how you wired your keyboard
+ * COLS: AVR pins used for columns, left to right
+ * ROWS: AVR pins used for rows, top to bottom
+ * DIODE_DIRECTION: COL2ROW = COL = Anode (+), ROW = Cathode (-, marked on diode)
+ *                  ROW2COL = ROW = Anode (+), COL = Cathode (-, marked on diode)
+ *
+ */
+// #define MATRIX_ROW_PINS { B0 } // B0 equivalents the ground pin
+// #define MATRIX_COL_PINS { E6, D7, C6, D4 }
+#define DIRECT_PINS { \
+    { E6, D7, C6, D4 } \
+}
+#define UNUSED_PINS
+
+/* COL2ROW, ROW2COL*/
+#define DIODE_DIRECTION COL2ROW
+
+
+/*
+ * Split Keyboard specific options, make sure you have 'SPLIT_KEYBOARD = yes' in your rules.mk, and define SOFT_SERIAL_PIN.
+ */
+// #define SOFT_SERIAL_PIN D0  // or D1, D2, D3, E6
+
+// #define BACKLIGHT_PIN B7
+// #define BACKLIGHT_BREATHING
+// #define BACKLIGHT_LEVELS 3
+#define BACKLIGHT_LED_COUNT 2
+#undef BACKLIGHT_PIN
+#define BACKLIGHT_PINS { F6, F7 }
+
+
+// #define RGB_DI_PIN E2
+// #ifdef RGB_DI_PIN
+//   #define RGBLED_NUM 16
+//   #define RGBLIGHT_HUE_STEP 8
+//   #define RGBLIGHT_SAT_STEP 8
+//   #define RGBLIGHT_VAL_STEP 8
+//   #define RGBLIGHT_LIMIT_VAL 255 /* The maximum brightness level */
+//   #define RGBLIGHT_SLEEP  /* If defined, the RGB lighting will be switched off when the host goes to sleep */
+// /*== all animations enable ==*/
+//   #define RGBLIGHT_ANIMATIONS
+// /*== or choose animations ==*/
+//   #define RGBLIGHT_EFFECT_BREATHING
+//   #define RGBLIGHT_EFFECT_RAINBOW_MOOD
+//   #define RGBLIGHT_EFFECT_RAINBOW_SWIRL
+//   #define RGBLIGHT_EFFECT_SNAKE
+//   #define RGBLIGHT_EFFECT_KNIGHT
+//   #define RGBLIGHT_EFFECT_CHRISTMAS
+//   #define RGBLIGHT_EFFECT_STATIC_GRADIENT
+//   #define RGBLIGHT_EFFECT_RGB_TEST
+//   #define RGBLIGHT_EFFECT_ALTERNATING
+// /*== customize breathing effect ==*/
+//   /*==== (DEFAULT) use fixed table instead of exp() and sin() ====*/
+//   #define RGBLIGHT_BREATHE_TABLE_SIZE 256      // 256(default) or 128 or 64
+//   /*==== use exp() and sin() ====*/
+//   #define RGBLIGHT_EFFECT_BREATHE_CENTER 1.85  // 1 to 2.7
+//   #define RGBLIGHT_EFFECT_BREATHE_MAX    255   // 0 to 255
+// #endif
+
+/* Debounce reduces chatter (unintended double-presses) - set 0 if debouncing is not needed */
+#define DEBOUNCE 5
+
+/* define if matrix has ghost (lacks anti-ghosting diodes) */
+//#define MATRIX_HAS_GHOST
+
+/* Mechanical locking support. Use KC_LCAP, KC_LNUM or KC_LSCR instead in keymap */
+#define LOCKING_SUPPORT_ENABLE
+/* Locking resynchronize hack */
+#define LOCKING_RESYNC_ENABLE
+
+/* If defined, GRAVE_ESC will always act as ESC when CTRL is held.
+ * This is userful for the Windows task manager shortcut (ctrl+shift+esc).
+ */
+// #define GRAVE_ESC_CTRL_OVERRIDE
+
+/*
+ * Force NKRO
+ *
+ * Force NKRO (nKey Rollover) to be enabled by default, regardless of the saved
+ * state in the bootmagic EEPROM settings. (Note that NKRO must be enabled in the
+ * makefile for this to work.)
+ *
+ * If forced on, NKRO can be disabled via magic key (default = LShift+RShift+N)
+ * until the next keyboard reset.
+ *
+ * NKRO may prevent your keystrokes from being detected in the BIOS, but it is
+ * fully operational during normal computer usage.
+ *
+ * For a less heavy-handed approach, enable NKRO via magic key (LShift+RShift+N)
+ * or via bootmagic (hold SPACE+N while plugging in the keyboard). Once set by
+ * bootmagic, NKRO mode will always be enabled until it is toggled again during a
+ * power-up.
+ *
+ */
+//#define FORCE_NKRO
+
+/*
+ * Magic Key Options
+ *
+ * Magic keys are hotkey commands that allow control over firmware functions of
+ * the keyboard. They are best used in combination with the HID Listen program,
+ * found here: https://www.pjrc.com/teensy/hid_listen.html
+ *
+ * The options below allow the magic key functionality to be changed. This is
+ * useful if your keyboard/keypad is missing keys and you want magic key support.
+ *
+ */
+
+/* key combination for magic key command */
+/* defined by default; to change, uncomment and set to the combination you want */
+// #define IS_COMMAND() (get_mods() == MOD_MASK_SHIFT)
+
+/* control how magic key switches layers */
+//#define MAGIC_KEY_SWITCH_LAYER_WITH_FKEYS  true
+//#define MAGIC_KEY_SWITCH_LAYER_WITH_NKEYS  true
+//#define MAGIC_KEY_SWITCH_LAYER_WITH_CUSTOM false
+
+/* override magic key keymap */
+//#define MAGIC_KEY_SWITCH_LAYER_WITH_FKEYS
+//#define MAGIC_KEY_SWITCH_LAYER_WITH_NKEYS
+//#define MAGIC_KEY_SWITCH_LAYER_WITH_CUSTOM
+//#define MAGIC_KEY_HELP           H
+//#define MAGIC_KEY_HELP_ALT       SLASH
+//#define MAGIC_KEY_DEBUG          D
+//#define MAGIC_KEY_DEBUG_MATRIX   X
+//#define MAGIC_KEY_DEBUG_KBD      K
+//#define MAGIC_KEY_DEBUG_MOUSE    M
+//#define MAGIC_KEY_VERSION        V
+//#define MAGIC_KEY_STATUS         S
+//#define MAGIC_KEY_CONSOLE        C
+//#define MAGIC_KEY_LAYER0         0
+//#define MAGIC_KEY_LAYER0_ALT     GRAVE
+//#define MAGIC_KEY_LAYER1         1
+//#define MAGIC_KEY_LAYER2         2
+//#define MAGIC_KEY_LAYER3         3
+//#define MAGIC_KEY_LAYER4         4
+//#define MAGIC_KEY_LAYER5         5
+//#define MAGIC_KEY_LAYER6         6
+//#define MAGIC_KEY_LAYER7         7
+//#define MAGIC_KEY_LAYER8         8
+//#define MAGIC_KEY_LAYER9         9
+//#define MAGIC_KEY_BOOTLOADER     B
+//#define MAGIC_KEY_BOOTLOADER_ALT ESC
+//#define MAGIC_KEY_LOCK           CAPS
+//#define MAGIC_KEY_EEPROM         E
+//#define MAGIC_KEY_EEPROM_CLEAR   BSPACE
+//#define MAGIC_KEY_NKRO           N
+//#define MAGIC_KEY_SLEEP_LED      Z
+
+/*
+ * Feature disable options
+ *  These options are also useful to firmware size reduction.
+ */
+
+/* disable debug print */
+//#define NO_DEBUG
+
+/* disable print */
+//#define NO_PRINT
+
+/* disable action features */
+//#define NO_ACTION_LAYER
+//#define NO_ACTION_TAPPING
+//#define NO_ACTION_ONESHOT
+//#define NO_ACTION_MACRO
+//#define NO_ACTION_FUNCTION
+
+/*
+ * MIDI options
+ */
+
+/* Prevent use of disabled MIDI features in the keymap */
+//#define MIDI_ENABLE_STRICT 1
+
+/* enable basic MIDI features:
+   - MIDI notes can be sent when in Music mode is on
+*/
+//#define MIDI_BASIC
+
+/* enable advanced MIDI features:
+   - MIDI notes can be added to the keymap
+   - Octave shift and transpose
+   - Virtual sustain, portamento, and modulation wheel
+   - etc.
+*/
+//#define MIDI_ADVANCED
+
+/* override number of MIDI tone keycodes (each octave adds 12 keycodes and allocates 12 bytes) */
+//#define MIDI_TONE_KEYCODE_OCTAVES 1
+
+/*
+ * HD44780 LCD Display Configuration
+ */
+/*
+#define LCD_LINES           2     //< number of visible lines of the display
+#define LCD_DISP_LENGTH    16     //< visibles characters per line of the display
+
+#define LCD_IO_MODE      1            //< 0: memory mapped mode, 1: IO port mode
+
+#if LCD_IO_MODE
+#define LCD_PORT         PORTB        //< port for the LCD lines
+#define LCD_DATA0_PORT   LCD_PORT     //< port for 4bit data bit 0
+#define LCD_DATA1_PORT   LCD_PORT     //< port for 4bit data bit 1
+#define LCD_DATA2_PORT   LCD_PORT     //< port for 4bit data bit 2
+#define LCD_DATA3_PORT   LCD_PORT     //< port for 4bit data bit 3
+#define LCD_DATA0_PIN    4            //< pin for 4bit data bit 0
+#define LCD_DATA1_PIN    5            //< pin for 4bit data bit 1
+#define LCD_DATA2_PIN    6            //< pin for 4bit data bit 2
+#define LCD_DATA3_PIN    7            //< pin for 4bit data bit 3
+#define LCD_RS_PORT      LCD_PORT     //< port for RS line
+#define LCD_RS_PIN       3            //< pin  for RS line
+#define LCD_RW_PORT      LCD_PORT     //< port for RW line
+#define LCD_RW_PIN       2            //< pin  for RW line
+#define LCD_E_PORT       LCD_PORT     //< port for Enable line
+#define LCD_E_PIN        1            //< pin  for Enable line
+#endif
+*/
+
+/* Bootmagic Lite key configuration */
+// #define BOOTMAGIC_LITE_ROW 0
+// #define BOOTMAGIC_LITE_COLUMN 0
diff --git a/keyboards/40percentclub/4pack/info.json b/keyboards/40percentclub/4pack/info.json
new file mode 100644
index 0000000000..8dd164e4b2
--- /dev/null
+++ b/keyboards/40percentclub/4pack/info.json
@@ -0,0 +1,12 @@
+{
+    "keyboard_name": "4pack", 
+    "url": "", 
+    "maintainer": "qmk", 
+    "width": 4, 
+    "height": 1, 
+    "layouts": {
+        "LAYOUT": {
+            "layout": [{"x":0, "y":0}, {"x":1, "y":0}, {"x":2, "y":0}, {"x":3, "y":0}]
+        }
+    }
+}
\ No newline at end of file
diff --git a/keyboards/40percentclub/4pack/keymaps/default/config.h b/keyboards/40percentclub/4pack/keymaps/default/config.h
new file mode 100644
index 0000000000..c76819ce5e
--- /dev/null
+++ b/keyboards/40percentclub/4pack/keymaps/default/config.h
@@ -0,0 +1,19 @@
+/* Copyright 2019 Arda Kilicdagi
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+
+#pragma once
+
+// place overrides here
diff --git a/keyboards/40percentclub/4pack/keymaps/default/keymap.c b/keyboards/40percentclub/4pack/keymaps/default/keymap.c
new file mode 100644
index 0000000000..19264651b6
--- /dev/null
+++ b/keyboards/40percentclub/4pack/keymaps/default/keymap.c
@@ -0,0 +1,26 @@
+/* Copyright 2019 Arda Kilicdagi
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+#include QMK_KEYBOARD_H
+
+
+const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = {
+    [0] = LAYOUT( /* Base */
+        KC_A, KC_S, KC_D, KC_F
+    ),
+};
+
+
+void matrix_init_user(void) { }
diff --git a/keyboards/40percentclub/4pack/keymaps/default/readme.md b/keyboards/40percentclub/4pack/keymaps/default/readme.md
new file mode 100644
index 0000000000..00bf43cb99
--- /dev/null
+++ b/keyboards/40percentclub/4pack/keymaps/default/readme.md
@@ -0,0 +1 @@
+# The default keymap for 4pack
diff --git a/keyboards/40percentclub/4pack/readme.md b/keyboards/40percentclub/4pack/readme.md
new file mode 100644
index 0000000000..5fcfbf892d
--- /dev/null
+++ b/keyboards/40percentclub/4pack/readme.md
@@ -0,0 +1,17 @@
+# 4 Pack
+
+![4pack](https://i.imgur.com/rioXXq5l.jpg)
+
+A 4-key macropad PCB with its switch and LED pins wired directly to microcontroller IO pins.
+
+You can find the main blog post about this macropad [here](http://www.40percent.club/2017/07/4-pack.html), also the Gerber files and other documentation is located [here](https://git.40percent.club/di0ib/Misc/src/branch/master/4pack).
+
+Keyboard Maintainer: [Arda Kilicdagi](http://github.com/ardakilic), [The QMK Community](https://github.com/qmk)  
+Hardware Supported: 4 Pack PCB, Pro Micro  
+Hardware Availability: [40percent.club](https://git.40percent.club/di0ib/Misc/src/branch/master/4pack)
+
+Make example for this macropad (after setting up your build environment):
+
+    make 40percentclub/4pack:default:flash
+
+See the [build environment setup](https://docs.qmk.fm/#/getting_started_build_tools) and the [make instructions](https://docs.qmk.fm/#/getting_started_make_guide) for more information. Brand new to QMK? Start with our [Complete Newbs Guide](https://docs.qmk.fm/#/newbs).
diff --git a/keyboards/40percentclub/4pack/rules.mk b/keyboards/40percentclub/4pack/rules.mk
new file mode 100644
index 0000000000..a0c9d34f54
--- /dev/null
+++ b/keyboards/40percentclub/4pack/rules.mk
@@ -0,0 +1,33 @@
+# MCU name
+MCU = atmega32u4
+
+# Bootloader selection
+#   Teensy       halfkay
+#   Pro Micro    caterina
+#   Atmel DFU    atmel-dfu
+#   LUFA DFU     lufa-dfu
+#   QMK DFU      qmk-dfu
+#   ATmega32A    bootloadHID
+#   ATmega328P   USBasp
+BOOTLOADER = caterina
+
+# Build Options
+#   change yes to no to disable
+#
+BOOTMAGIC_ENABLE = no       # Virtual DIP switch configuration
+MOUSEKEY_ENABLE = no        # Mouse keys
+EXTRAKEY_ENABLE = yes       # Audio control and System control
+CONSOLE_ENABLE = no         # Console for debug
+COMMAND_ENABLE = no         # Commands for debug and configuration
+# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE
+SLEEP_LED_ENABLE = no       # Breathing sleep LED during USB suspend
+# if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
+NKRO_ENABLE = no            # USB Nkey Rollover
+BACKLIGHT_ENABLE = yes      # Enable keyboard backlight functionality
+RGBLIGHT_ENABLE = no        # Enable keyboard RGB underglow
+MIDI_ENABLE = no            # MIDI support
+UNICODE_ENABLE = no         # Unicode
+BLUETOOTH_ENABLE = no       # Enable Bluetooth with the Adafruit EZ-Key HID
+AUDIO_ENABLE = no           # Audio output on port C6
+FAUXCLICKY_ENABLE = no      # Use buzzer to emulate clicky switches
+HD44780_ENABLE = no         # Enable support for HD44780 based LCDs
diff --git a/keyboards/40percentclub/4x4/rules.mk b/keyboards/40percentclub/4x4/rules.mk
index 4ab5e7431c..c653c6753d 100644
--- a/keyboards/40percentclub/4x4/rules.mk
+++ b/keyboards/40percentclub/4x4/rules.mk
@@ -1,61 +1,16 @@
 # MCU name
 MCU = atmega32u4
 
-# Processor frequency.
-#     This will define a symbol, F_CPU, in all source code files equal to the
-#     processor frequency in Hz. You can then use this symbol in your source code to
-#     calculate timings. Do NOT tack on a 'UL' at the end, this will be done
-#     automatically to create a 32-bit value in your source code.
-#
-#     This will be an integer division of F_USB below, as it is sourced by
-#     F_USB after it has run through any CPU prescalers. Note that this value
-#     does not *change* the processor frequency - it should merely be updated to
-#     reflect the processor speed set externally so that the code can use accurate
-#     software delays.
-F_CPU = 16000000
-
-#
-# LUFA specific
-#
-# Target architecture (see library "Board Types" documentation).
-ARCH = AVR8
-
-# Input clock frequency.
-#     This will define a symbol, F_USB, in all source code files equal to the
-#     input clock frequency (before any prescaling is performed) in Hz. This value may
-#     differ from F_CPU if prescaling is used on the latter, and is required as the
-#     raw input clock is fed directly to the PLL sections of the AVR for high speed
-#     clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
-#     at the end, this will be done automatically to create a 32-bit value in your
-#     source code.
-#
-#     If no clock division is performed on the input clock inside the AVR (via the
-#     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
-F_USB = $(F_CPU)
-
-# Interrupt driven control endpoint task(+60)
-OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
-
-
 # Bootloader selection
 #   Teensy       halfkay
 #   Pro Micro    caterina
 #   Atmel DFU    atmel-dfu
 #   LUFA DFU     lufa-dfu
 #   QMK DFU      qmk-dfu
-#   atmega32a    bootloadHID
+#   ATmega32A    bootloadHID
+#   ATmega328P   USBasp
 BOOTLOADER = caterina
 
-
-# If you don't know the bootloader type, then you can specify the
-# Boot Section Size in *bytes* by uncommenting out the OPT_DEFS line
-#   Teensy halfKay      512
-#   Teensy++ halfKay    1024
-#   Atmel DFU loader    4096
-#   LUFA bootloader     4096
-#   USBaspLoader        2048
-# OPT_DEFS += -DBOOTLOADER_SIZE=4096
-
 # Build Options
 #   change yes to no to disable
 #
diff --git a/keyboards/40percentclub/5x5/rules.mk b/keyboards/40percentclub/5x5/rules.mk
index 237de64977..d8b82248c6 100644
--- a/keyboards/40percentclub/5x5/rules.mk
+++ b/keyboards/40percentclub/5x5/rules.mk
@@ -1,62 +1,16 @@
 # MCU name
 MCU = atmega32u4
 
-# Processor frequency.
-#     This will define a symbol, F_CPU, in all source code files equal to the
-#     processor frequency in Hz. You can then use this symbol in your source code to
-#     calculate timings. Do NOT tack on a 'UL' at the end, this will be done
-#     automatically to create a 32-bit value in your source code.
-#
-#     This will be an integer division of F_USB below, as it is sourced by
-#     F_USB after it has run through any CPU prescalers. Note that this value
-#     does not *change* the processor frequency - it should merely be updated to
-#     reflect the processor speed set externally so that the code can use accurate
-#     software delays.
-F_CPU = 16000000
-
-#
-# LUFA specific
-#
-# Target architecture (see library "Board Types" documentation).
-ARCH = AVR8
-
-# Input clock frequency.
-#     This will define a symbol, F_USB, in all source code files equal to the
-#     input clock frequency (before any prescaling is performed) in Hz. This value may
-#     differ from F_CPU if prescaling is used on the latter, and is required as the
-#     raw input clock is fed directly to the PLL sections of the AVR for high speed
-#     clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
-#     at the end, this will be done automatically to create a 32-bit value in your
-#     source code.
-#
-#     If no clock division is performed on the input clock inside the AVR (via the
-#     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
-F_USB = $(F_CPU)
-
-# Interrupt driven control endpoint task(+60)
-OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
-
-