Add support for the KC60 v2.0 2015-09-12 (#360)

* Don't save the ctags file in the repo.

* Initial support for the KC60 board. Only 5x5 working so far.

* Rename because this isn't the same KC60 as others.

* Add in some generic layout.
Pins seem to be in the right order except the 6th column spews
gibberish.

* Don't need this for now.

* Move this to some other folder.

* Trying again to start over.

* Don't need to start over because I figured out why the 'broken' stuff wasn't working.

* Attempt to enable backlighting. It's on on pin B7 like other boards.

* Fix last port changes and fix LED control in keymap.

* Trying some other LED code.

* Bootloader needs to be bigger. Disabling backlight for now.

* Simplify LED code while I try to figure it out.

* Turn back on backlighting.

* Backlighting works now. Just need to get levels or breathing working.

* Trying to allow for turning off the LEDs before I get to brightness levels.

* The missing link: need to run the init_ports function for LEDs to work properly.

* Removing breathing stuff since it bricks the board.

* Clean up default layer.

* Cleanup keymap, KC60 doesn't support a 5th right bottom-row button.

1 files changed, 158 insertions, 0 deletions

diff --git a/keyboard/kc60_v2/Makefile b/keyboard/kc60_v2/Makefile
new file mode 100644
index 0000000000..33ece31647
--- /dev/null
+++ b/keyboard/kc60_v2/Makefile
@@ -0,0 +1,158 @@
+#----------------------------------------------------------------------------
+# On command line:
+#
+# make all = Make software.
+#
+# make clean = Clean out built project files.
+#
+# make coff = Convert ELF to AVR COFF.
+#
+# make extcoff = Convert ELF to AVR Extended COFF.
+#
+# make program = Download the hex file to the device.
+#                Please customize your programmer settings(PROGRAM_CMD)
+#
+# make teensy = Download the hex file to the device, using teensy_loader_cli.
+#               (must have teensy_loader_cli installed).
+#
+# make dfu = Download the hex file to the device, using dfu-programmer (must
+#            have dfu-programmer installed).
+#
+# make flip = Download the hex file to the device, using Atmel FLIP (must
+#             have Atmel FLIP installed).
+#
+# make dfu-ee = Download the eeprom file to the device, using dfu-programmer
+#               (must have dfu-programmer installed).
+#
+# make flip-ee = Download the eeprom file to the device, using Atmel FLIP
+#                (must have Atmel FLIP installed).
+#
+# make debug = Start either simulavr or avarice as specified for debugging, 
+#              with avr-gdb or avr-insight as the front end for debugging.
+#
+# make filename.s = Just compile filename.c into the assembler code only.
+#
+# make filename.i = Create a preprocessed source file for use in submitting
+#                   bug reports to the GCC project.
+#
+# To rebuild project do "make clean" then "make all".
+#----------------------------------------------------------------------------
+
+# Target file name (without extension).
+TARGET = kc60
+
+
+# Directory common source filess exist
+TOP_DIR = ../..
+TMK_DIR = ../../tmk_core
+
+# Directory keyboard dependent files exist
+TARGET_DIR = .
+
+# # project specific files
+SRC = kc60.c
+
+ifdef KEYMAP
+    SRC := keymaps/$(KEYMAP).c $(SRC)
+else
+    SRC := keymaps/default.c $(SRC)
+endif
+
+CONFIG_H = config.h
+
+# MCU name
+#MCU = at90usb1287
+MCU = atmega32u4
+
+# Processor frequency.
+#     This will define a symbol, F_CPU, in all source code files equal to the
+#     processor frequency in Hz. You can then use this symbol in your source code to
+#     calculate timings. Do NOT tack on a 'UL' at the end, this will be done
+#     automatically to create a 32-bit value in your source code.
+#
+#     This will be an integer division of F_USB below, as it is sourced by
+#     F_USB after it has run through any CPU prescalers. Note that this value
+#     does not *change* the processor frequency - it should merely be updated to
+#     reflect the processor speed set externally so that the code can use accurate
+#     software delays.
+F_CPU = 16000000
+
+
+#
+# LUFA specific
+#
+# Target architecture (see library "Board Types" documentation).
+ARCH = AVR8
+
+# Input clock frequency.
+#     This will define a symbol, F_USB, in all source code files equal to the
+#     input clock frequency (before any prescaling is performed) in Hz. This value may
+#     differ from F_CPU if prescaling is used on the latter, and is required as the
+#     raw input clock is fed directly to the PLL sections of the AVR for high speed
+#     clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
+#     at the end, this will be done automatically to create a 32-bit value in your
+#     source code.
+#
+#     If no clock division is performed on the input clock inside the AVR (via the
+#     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
+F_USB = $(F_CPU)
+
+# Interrupt driven control endpoint task(+60)
+OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
+
+
+# Boot Section Size in *bytes*
+#   Teensy halfKay   512
+#   Teensy++ halfKay 1024
+#   Atmel DFU loader 4096
+#   LUFA bootloader  4096
+#   USBaspLoader     2048
+OPT_DEFS += -DBOOTLOADER_SIZE=4096
+
+
+# Build Options
+#   change yes to no to disable
+#
+BOOTMAGIC_ENABLE = yes      # Virtual DIP switch configuration(+1000)
+MOUSEKEY_ENABLE = yes       # Mouse keys(+4700)
+EXTRAKEY_ENABLE = yes       # Audio control and System control(+450)
+CONSOLE_ENABLE = yes        # Console for debug(+400)
+COMMAND_ENABLE = yes        # Commands for debug and configuration
+KEYBOARD_LOCK_ENABLE = yes  # Allow locking of keyboard via magic key
+# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE
+SLEEP_LED_ENABLE = no       # Breathing sleep LED during USB suspend
+# if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
+NKRO_ENABLE = no            # USB Nkey Rollover
+BACKLIGHT_ENABLE = yes      # Enable keyboard backlight functionality
+MIDI_ENABLE = no            # MIDI controls
+UNICODE_ENABLE = no         # Unicode
+BLUETOOTH_ENABLE = no       # Enable Bluetooth with the Adafruit EZ-Key HID
+AUDIO_ENABLE = no           # Audio output on port C6
+
+
+ifdef KEYMAP
+
+ifeq ("$(wildcard keymaps/$(KEYMAP).c)","")
+ifneq ("$(wildcard keymaps/$(KEYMAP)/makefile.mk)","")
+    include keymaps/$(KEYMAP)/makefile.mk
+endif 
+endif
+
+else
+
+ifneq ("$(wildcard keymaps/default/makefile.mk)","")
+    include keymaps/default/makefile.mk
+endif
+
+endif
+
+# Optimize size but this may cause error "relocation truncated to fit"
+#EXTRALDFLAGS = -Wl,--relax
+
+# Search Path
+VPATH += $(TARGET_DIR)
+VPATH += $(TOP_DIR)
+VPATH += $(TMK_DIR)
+
+include $(TOP_DIR)/quantum/quantum.mk
+