cleans up folder structure

* consolidates docs
* deletes converter/
* updates .md references (most)

20 files changed, 0 insertions, 2351 deletions

diff --git a/converter/ps2_usb/Makefile b/converter/ps2_usb/Makefile
deleted file mode 100644
index 51b2225661..0000000000
--- a/converter/ps2_usb/Makefile
+++ /dev/null
@@ -1,105 +0,0 @@
-# 
-# Makefile for Teensy
-#
-# Target file name (without extension).
-TARGET = ps2_usb_lufa
-
-# Directory common source filess exist
-TMK_DIR = ../../tmk_core
-
-# Directory keyboard dependent files exist
-TARGET_DIR = .
-
-# project specific files
-SRC =	keymap_common.c \
-	matrix.c \
-	led.c
-
-ifdef KEYMAP
-    SRC := keymap_$(KEYMAP).c $(SRC)
-else
-    SRC := keymap_plain.c $(SRC)
-endif
-
-CONFIG_H = config.h
-
-
-# MCU name
-#MCU = at90usb1287
-MCU = atmega32u4
-
-# Processor frequency.
-#     This will define a symbol, F_CPU, in all source code files equal to the
-#     processor frequency in Hz. You can then use this symbol in your source code to
-#     calculate timings. Do NOT tack on a 'UL' at the end, this will be done
-#     automatically to create a 32-bit value in your source code.
-#
-#     This will be an integer division of F_USB below, as it is sourced by
-#     F_USB after it has run through any CPU prescalers. Note that this value
-#     does not *change* the processor frequency - it should merely be updated to
-#     reflect the processor speed set externally so that the code can use accurate
-#     software delays.
-F_CPU = 16000000
-
-
-#
-# LUFA specific
-#
-# Target architecture (see library "Board Types" documentation).
-ARCH = AVR8
-
-# Input clock frequency.
-#     This will define a symbol, F_USB, in all source code files equal to the
-#     input clock frequency (before any prescaling is performed) in Hz. This value may
-#     differ from F_CPU if prescaling is used on the latter, and is required as the
-#     raw input clock is fed directly to the PLL sections of the AVR for high speed
-#     clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
-#     at the end, this will be done automatically to create a 32-bit value in your
-#     source code.
-#
-#     If no clock division is performed on the input clock inside the AVR (via the
-#     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
-F_USB = $(F_CPU)
-
-# Interrupt driven control endpoint task(+60)
-#OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
-
-
-# Boot Section Size in *bytes*
-#   Teensy halfKay   512
-#   Teensy++ halfKay 1024
-#   Atmel DFU loader 4096
-#   LUFA bootloader  4096
-#   USBaspLoader     2048
-OPT_DEFS += -DBOOTLOADER_SIZE=512
-
-
-# Build Options
-#   comment out to disable the options.
-#
-#BOOTMAGIC_ENABLE = yes	# Virtual DIP switch configuration(+1000)
-MOUSEKEY_ENABLE = yes	# Mouse keys(+4700)
-EXTRAKEY_ENABLE = yes	# Audio control and System control(+450)
-CONSOLE_ENABLE = yes	# Console for debug(+400)
-COMMAND_ENABLE = yes    # Commands for debug and configuration
-NKRO_ENABLE = yes	# USB Nkey Rollover - not yet supported in LUFA
-
-
-# PS/2 Options
-#
-#PS2_USE_USART = yes	# uses hardware USART engine for PS/2 signal receive(recomened)
-PS2_USE_INT = yes	# uses external interrupt for falling edge of PS/2 clock pin
-#PS2_USE_BUSYWAIT = yes	# uses primitive reference code
-
-
-# Optimize size but this may cause error "relocation truncated to fit"
-#EXTRALDFLAGS = -Wl,--relax
-
-# Search Path
-VPATH += $(TARGET_DIR)
-VPATH += $(TMK_DIR)
-
-include $(TMK_DIR)/protocol.mk
-include $(TMK_DIR)/protocol/lufa.mk
-include $(TMK_DIR)/common.mk
-include $(TMK_DIR)/rules.mk
diff --git a/converter/ps2_usb/Makefile.mbed b/converter/ps2_usb/Makefile.mbed
deleted file mode 100644
index a7ea5bcf24..0000000000
--- a/converter/ps2_usb/Makefile.mbed
+++ /dev/null
@@ -1,46 +0,0 @@
-PROJECT = ps2_usb
-
-TMK_DIR = ../../tmk_core
-MBED_DIR = $(TMK_DIR)/tool/mbed/mbed-sdk
-
-#VPATH += $(MBED_DIR):$(TMK_DIR)
-vpath %.s .:$(MBED_DIR):$(TMK_DIR)
-vpath %.c .:$(MBED_DIR):$(TMK_DIR)
-vpath %.cpp .:$(MBED_DIR):$(TMK_DIR)
-
-OBJDIR = ./build
-
-OBJECTS = \
-	$(OBJDIR)/protocol/ps2_busywait.o \
-	$(OBJDIR)/protocol/ps2_io_mbed.o \
-	$(OBJDIR)/./keymap_common.o \
-	$(OBJDIR)/./matrix.o \
-	$(OBJDIR)/./led.o \
-	$(OBJDIR)/./main.o
-
-ifdef KEYMAP
-    OBJECTS := $(OBJDIR)/keymap_$(KEYMAP).o $(OBJECTS)
-else
-    OBJECTS := $(OBJDIR)/keymap_plain.o $(OBJECTS)
-endif
-
-CONFIG_H = config_mbed.h
-
-SYS_OBJECTS = 
-
-INCLUDE_PATHS = -I.
-
-LIBRARY_PATHS = 
-LIBRARIES = 
-
-# Build Options
-#   Comment out to disable
-#BOOTMAGIC_ENABLE = yes
-MOUSEKEY_ENABLE = yes
-
-
-#include $(TMK_DIR)/tool/mbed/mk20d50m.mk
-include $(TMK_DIR)/tool/mbed/lpc11u35_501.mk
-include $(TMK_DIR)/tool/mbed/mbed.mk
-include $(TMK_DIR)/tool/mbed/common.mk
-include $(TMK_DIR)/tool/mbed/gcc.mk
diff --git a/converter/ps2_usb/Makefile.pjrc b/converter/ps2_usb/Makefile.pjrc
deleted file mode 100644
index 64319aca88..0000000000
--- a/converter/ps2_usb/Makefile.pjrc
+++ /dev/null
@@ -1,75 +0,0 @@
-# Target file name (without extension).
-TARGET = ps2_usb_pjrc
-
-# Directory common source filess exist
-TMK_DIR = ../../tmk_core
-
-# Directory keyboard dependent files exist
-TARGET_DIR = .
-
-# keyboard dependent files
-SRC =   keymap_common.c \
-	matrix.c \
-	led.c
-
-ifdef KEYMAP
-    SRC := keymap_$(KEYMAP).c $(SRC)
-else
-    SRC := keymap_plain.c $(SRC)
-endif
-
-CONFIG_H = config.h
-
-
-# MCU name, you MUST set this to match the board you are using
-# type "make clean" after changing this, so all files will be rebuilt
-#MCU = at90usb162       # Teensy 1.0
-MCU = atmega32u4       # Teensy 2.0
-#MCU = at90usb646       # Teensy++ 1.0
-#MCU = at90usb1286      # Teensy++ 2.0
-
-
-# Processor frequency.
-#   Normally the first thing your program should do is set the clock prescaler,
-#   so your program will run at the correct speed.  You should also set this
-#   variable to same clock speed.  The _delay_ms() macro uses this, and many
-#   examples use this variable to calculate timings.  Do not add a "UL" here.
-F_CPU = 16000000
-
-
-# Boot Section Size in *bytes*
-#   Teensy halfKay   512
-#   Teensy++ halfKay 1024
-#   Atmel DFU loader 4096
-#   LUFA bootloader  4096
-#   USBaspLoader     2048
-OPT_DEFS += -DBOOTLOADER_SIZE=4096
-
-
-# Build Options
-#   *Comment out* to disable the options.
-#
-#BOOTMAGIC_ENABLE = yes	# Virtual DIP switch configuration(+1000)
-MOUSEKEY_ENABLE = yes	# Mouse keys
-EXTRAKEY_ENABLE = yes	# Audio control and System control
-CONSOLE_ENABLE = yes	# Console for debug(+400)
-COMMAND_ENABLE = yes    # Commands for debug and configuration
-NKRO_ENABLE = yes	# USB Nkey Rollover
-
-
-# PS/2 Options
-#
-#PS2_USE_USART = yes	# uses hardware USART engine for PS/2 signal receive(recomened)
-#PS2_USE_INT = yes	# uses external interrupt for falling edge of PS/2 clock pin
-PS2_USE_BUSYWAIT = yes	# uses primitive reference code
-
-
-# Search Path
-VPATH += $(TARGET_DIR)
-VPATH += $(TMK_DIR)
-
-
-include $(TMK_DIR)/protocol.mk
-include $(TMK_DIR)/protocol/pjrc.mk
-include $(TMK_DIR)/common.mk
-include $(TMK_DIR)/rules.mk
diff --git a/converter/ps2_usb/Makefile.tmk_rev1 b/converter/ps2_usb/Makefile.tmk_rev1
deleted file mode 100644
index 6aaef49969..0000000000
--- a/converter/ps2_usb/Makefile.tmk_rev1
+++ /dev/null
@@ -1,98 +0,0 @@
-# 
-# Makefile for TMK keyboard converter rev2
-#     https://github.com/tmk/keyboard_converter#pcb-rev1
-#
-# Target file name (without extension).
-TARGET = ps2_usb_tmk_rev1
-
-# Directory common source filess exist
-TMK_DIR = ../../tmk_core
-
-# Directory keyboard dependent files exist
-TARGET_DIR = .
-
-# project specific files
-SRC =	keymap_common.c \
-	matrix.c \
-	led.c
-
-ifdef KEYMAP
-    SRC := keymap_$(KEYMAP).c $(SRC)
-else
-    SRC := keymap_plain.c $(SRC)
-endif
-
-CONFIG_H = config_tmk_rev1.h
-
-
-# MCU name
-MCU = atmega32u4
-
-# Processor frequency.
-#     This will define a symbol, F_CPU, in all source code files equal to the
-#     processor frequency in Hz. You can then use this symbol in your source code to
-#     calculate timings. Do NOT tack on a 'UL' at the end, this will be done
-#     automatically to create a 32-bit value in your source code.
-#
-#     This will be an integer division of F_USB below, as it is sourced by
-#     F_USB after it has run through any CPU prescalers. Note that this value
-#     does not *change* the processor frequency - it should merely be updated to
-#     reflect the processor speed set externally so that the code can use accurate
-#     software delays.
-F_CPU = 16000000
-
-
-#
-# LUFA specific
-#
-# Target architecture (see library "Board Types" documentation).
-ARCH = AVR8
-
-# Input clock frequency.
-#     This will define a symbol, F_USB, in all source code files equal to the
-#     input clock frequency (before any prescaling is performed) in Hz. This value may
-#     differ from F_CPU if prescaling is used on the latter, and is required as the
-#     raw input clock is fed directly to the PLL sections of the AVR for high speed
-#     clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
-#     at the end, this will be done automatically to create a 32-bit value in your
-#     source code.
-#
-#     If no clock division is performed on the input clock inside the AVR (via the
-#     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
-F_USB = $(F_CPU)
-
-
-# Boot Section Size in *bytes*
-#   Teensy halfKay   512
-#   Teensy++ halfKay 1024
-#   Atmel DFU loader 4096
-#   LUFA bootloader  4096
-#   USBaspLoader     2048
-OPT_DEFS += -DBOOTLOADER_SIZE=4096
-
-
-# Build Options
-#   comment out to disable the options.
-#
-#BOOTMAGIC_ENABLE = yes	# Virtual DIP switch configuration(+1000)
-MOUSEKEY_ENABLE = yes	# Mouse keys(+4700)
-EXTRAKEY_ENABLE = yes	# Audio control and System control(+450)
-CONSOLE_ENABLE = yes	# Console for debug(+400)
-COMMAND_ENABLE = yes    # Commands for debug and configuration
-#NKRO_ENABLE = yes	# USB Nkey Rollover - not yet supported in LUFA
-
-
-# PS/2 Options
-#
-PS2_USE_USART = yes	# uses hardware USART engine for PS/2 signal receive(recomened)
-#PS2_USE_BUSYWAIT = yes	# uses primitive reference code
-
-
-# Search Path
-VPATH += $(TARGET_DIR)
-VPATH += $(TMK_DIR)
-
-include $(TMK_DIR)/protocol.mk
-include $(TMK_DIR)/protocol/lufa.mk
-include $(TMK_DIR)/common.mk
-include $(TMK_DIR)/rules.mk
diff --git a/converter/ps2_usb/Makefile.tmk_rev2 b/converter/ps2_usb/Makefile.tmk_rev2
deleted file mode 100644
index 5049a22703..0000000000
--- a/converter/ps2_usb/Makefile.tmk_rev2
+++ /dev/null
@@ -1,98 +0,0 @@
-# 
-# Makefile for TMK keyboard converter rev2
-#     https://github.com/tmk/keyboard_converter#pcb-rev2
-#
-# Target file name (without extension).
-TARGET = ps2_usb_tmk_rev2
-
-# Directory common source filess exist
-TMK_DIR = ../../tmk_core
-
-# Directory keyboard dependent files exist
-TARGET_DIR = .
-
-# project specific files
-SRC =	keymap_common.c \
-	matrix.c \
-	led.c
-
-ifdef KEYMAP
-    SRC := keymap_$(KEYMAP).c $(SRC)
-else
-    SRC := keymap_plain.c $(SRC)
-endif
-
-CONFIG_H = config_tmk_rev2.h
-
-
-# MCU name
-MCU = atmega32u2
-
-# Processor frequency.
-#     This will define a symbol, F_CPU, in all source code files equal to the
-#     processor frequency in Hz. You can then use this symbol in your source code to
-#     calculate timings. Do NOT tack on a 'UL' at the end, this will be done
-#     automatically to create a 32-bit value in your source code.
-#
-#     This will be an integer division of F_USB below, as it is sourced by
-#     F_USB after it has run through any CPU prescalers. Note that this value
-#     does not *change* the processor frequency - it should merely be updated to
-#     reflect the processor speed set externally so that the code can use accurate
-#     software delays.
-F_CPU = 16000000
-
-
-#
-# LUFA specific
-#
-# Target architecture (see library "Board Types" documentation).
-ARCH = AVR8
-
-# Input clock frequency.
-#     This will define a symbol, F_USB, in all source code files equal to the
-#     input clock frequency (before any prescaling is performed) in Hz. This value may
-#     differ from F_CPU if prescaling is used on the latter, and is required as the
-#     raw input clock is fed directly to the PLL sections of the AVR for high speed
-#     clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
-#     at the end, this will be done automatically to create a 32-bit value in your
-#     source code.
-#
-#     If no clock division is performed on the input clock inside the AVR (via the
-#     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
-F_USB = $(F_CPU)
-
-
-# Boot Section Size in *bytes*
-#   Teensy halfKay   512
-#   Teensy++ halfKay 1024
-#   Atmel DFU loader 4096
-#   LUFA bootloader  4096
-#   USBaspLoader     2048
-OPT_DEFS += -DBOOTLOADER_SIZE=4096
-
-
-# Build Options
-#   comment out to disable the options.
-#
-#BOOTMAGIC_ENABLE = yes	# Virtual DIP switch configuration(+1000)
-MOUSEKEY_ENABLE = yes	# Mouse keys(+4700)
-EXTRAKEY_ENABLE = yes	# Audio control and System control(+450)
-CONSOLE_ENABLE = yes	# Console for debug(+400)
-COMMAND_ENABLE = yes    # Commands for debug and configuration
-#NKRO_ENABLE = yes	# USB Nkey Rollover - not yet supported in LUFA
-
-
-# PS/2 Options
-#
-PS2_USE_INT = yes	# uses external interrupt for falling edge of PS/2 clock pin
-#PS2_USE_BUSYWAIT = yes	# uses primitive reference code
-
-
-# Search Path
-VPATH += $(TARGET_DIR)
-VPATH += $(TMK_DIR)
-
-include $(TMK_DIR)/protocol.mk
-include $(TMK_DIR)/protocol/lufa.mk
-include $(TMK_DIR)/common.mk
-include $(TMK_DIR)/rules.mk
diff --git a/converter/ps2_usb/Makefile.vusb b/converter/ps2_usb/Makefile.vusb
deleted file mode 100644
index d9fa12bcda..0000000000
--- a/converter/ps2_usb/Makefile.vusb
+++ /dev/null
@@ -1,107 +0,0 @@
-# Target file name (without extension).
-TARGET = ps2_usb_vusb
-
-# Directory common source filess exist
-TMK_DIR = ../../tmk_core
-
-# Directory keyboard dependent files exist
-TARGET_DIR = .
-
-# keyboard dependent files
-SRC = keymap_common.c \
-	matrix.c \
-	led.c
-
-ifdef KEYMAP
-    SRC := keymap_$(KEYMAP).c $(SRC)
-else
-    SRC := keymap_plain.c $(SRC)
-endif
-
-CONFIG_H = config.h
-
-
-# Use USART for PS/2. With V-USB INT and BUSYWAIT code is not useful.
-PS2_USE_USART = yes
-
-
-# V-USB debug level: To use ps2_usart.c level must be 0
-# ps2_usart.c requires USART to receive PS/2 signal.
-OPT_DEFS += -DDEBUG_LEVEL=0
-
-
-# MCU name, you MUST set this to match the board you are using
-# type "make clean" after changing this, so all files will be rebuilt
-#MCU = at90usb162       # Teensy 1.0
-#MCU = atmega32u4       # Teensy 2.0
-#MCU = at90usb646       # Teensy++ 1.0
-#MCU = at90usb1286      # Teensy++ 2.0
-MCU = atmega168
-
-
-# Processor frequency.
-#   Normally the first thing your program should do is set the clock prescaler,
-#   so your program will run at the correct speed.  You should also set this
-#   variable to same clock speed.  The _delay_ms() macro uses this, and many
-#   examples use this variable to calculate timings.  Do not add a "UL" here.
-F_CPU = 20000000
-
-
-# Build Options
-#   comment out to disable the options.
-#
-MOUSEKEY_ENABLE = yes	# Mouse keys
-EXTRAKEY_ENABLE = yes	# Audio control and System control
-#NKRO_ENABLE = yes	# USB Nkey Rollover
-NO_UART = yes		# UART is unavailable
-
-
-
-#---------------- Programming Options --------------------------
-AVRDUDE = avrdude
-# Type: avrdude -c ? to get a full listing.
-AVRDUDE_PROGRAMMER = usbasp
-AVRDUDE_PORT =
-AVRDUDE_WRITE_FLASH = -U flash:w:$(TARGET).hex
-#AVRDUDE_WRITE_EEPROM = -U eeprom:w:$(TARGET).eep
-
-# Uncomment the following if you want avrdude's erase cycle counter.
-# Note that this counter needs to be initialized first using -Yn,
-# see avrdude manual.
-#AVRDUDE_ERASE_COUNTER = -y
-
-# Uncomment the following if you do /not/ wish a verification to be
-# performed after programming the device.
-#AVRDUDE_NO_VERIFY = -V
-
-# Increase verbosity level.  Please use this when submitting bug
-# reports about avrdude. See <http://savannah.nongnu.org/projects/avrdude> 
-# to submit bug reports.
-#AVRDUDE_VERBOSE = -v -v
-
-#AVRDUDE_FLAGS = -p $(MCU) -P $(AVRDUDE_PORT) -c $(AVRDUDE_PROGRAMMER)
-AVRDUDE_FLAGS = -p $(MCU) -c $(AVRDUDE_PROGRAMMER)
-AVRDUDE_FLAGS += $(AVRDUDE_NO_VERIFY)
-AVRDUDE_FLAGS += $(AVRDUDE_VERBOSE)
-AVRDUDE_FLAGS += $(AVRDUDE_ERASE_COUNTER)
-
-PROGRAM_CMD = $(AVRDUDE) $(AVRDUDE_FLAGS) $(AVRDUDE_WRITE_FLASH) $(AVRDUDE_WRITE_EEPROM)
-
-
-# Boot Section Size in bytes
-#   Teensy halfKay   512
-#   Atmel DFU loader 4096
-#   LUFA bootloader  4096
-#   USBasp           2048
-OPT_DEFS += -DBOOTLOADER_SIZE=2048
-
-
-# Search Path
-VPATH += $(TARGET_DIR)
-VPATH += $(TMK_DIR)
-
-
-include $(TMK_DIR)/protocol.mk
-include $(TMK_DIR)/common.mk
-include $(TMK_DIR)/protocol/vusb.mk
-include $(TMK_DIR)/rules.mk
diff --git a/converter/ps2_usb/README.md b/converter/ps2_usb/README.md
deleted file mode 100644
index 74464e2640..0000000000
--- a/converter/ps2_usb/README.md
+++ /dev/null
@@ -1,84 +0,0 @@
-PS/2 to USB keyboard converter
-==============================
-This firmware converts PS/2 keyboard protocol to USB.(It supports Scan Code Set 2.)
-
-
-Connect Wires
--------------
-In case of Teensy2.0(ATMega32U4):
-
-1. Connect **Vcc** and **GND**.
-2. Connect **Clock** and **Data** line. 
-    - **Interrupt**:   **Clock** is on `PD1` and **Data** on `PD0`.(Recommended. Soarer's converter compatible)
-    - **Busywait**:    **Clock** is on `PD1` and **Data** on `PD0`.
-    - **USART**:       **Clock** is on `PD5` and **Data** on `PD2`.
-3. Optionally you need pull-up resistor. 1K-10K Ohm is OK.
-
-To change pin configuration edit **config.h** and **Makefile**.
-
-
-Build Firmware
---------------
-For **PJRC Teensy** just run `make`:
-
-    $ make clean
-    $ make
-
-To select keymap:
-
-    $ make clean
-    $ make KEYMAP=[plain|jis|spacefn|...]
-
-After that you will find HEX file `ps2_usb_lufa.hex` in current directory.
-
-
-- For **TMK converter Rev.1** use `make -f Makefile.tmk_rev1` instead of `make` and HEX file is `ps2_usb_tmk_rev1.hex`.
-
-- For **TMK converter Rev.2** use `make -f Makefile.tmk_rev2` instead of `make` and HEX file is `ps2_usb_tmk_rev2.hex`.
-
-
-Keymap
-------
-Several version of keymap are available in advance but you are recommended to define your favorite layout yourself. To define your own keymap create file named `keymap_<name>.c` and see keymap document(you can find in README.md of top directory) and existent keymap files.
-
-
-PS/2 signal handling implementations
-------------------------------------
-Following three methods can be used to implement PS/2 signal handling.
-
-### Simple and stupid busy-wait(ps2_busywait.c)
-    This is expected to implemented with portable C code for reference.
-### Interrupt driven(ps2_interrupt.c)
-    Uses pin interrupt to detect falling edge of clock line.
-### USART hardware module(ps2_usart.c)
-    Uses AVR USART engine to receive PS/2 signal.
-
-To select method edit Makefile.
-
-
-V-USB Support
--------------
-With V-USB you can use this converter on ATmega(168/328) but it doesn't support NKRO at this time.
-
-Circuit:
-
-                    +---+   +---------------+
-    USB            GND  |   |   ATmega168   |
-    ===                 C3  |               |
-    5V <-------+--------+---|Vcc,AVCC       |        PS/2
-               R1           |               |        ====
-    D- <----+--+-----R2-----|INT1        RXD|------->DATA
-    D+ <----|---+----R3-----|INT0        XCK|------->CLOCK
-            Z1  Z2          |               |      ->5V
-    GND<----+---+--+--+-----|GND            |      ->GND
-                   |  |     |               |
-                   |  C2-+--|XTAL1          |
-                   |     X1 |               |
-                   +--C3-+--|XTAL2          |
-                            +---------------+
-    R1:     1.5K Ohm
-    R2,R3:  68 Ohm
-    Z1,Z2:  Zenner 3.6V
-    C1,C2:  22pF
-    C3:     0.1uF
-    X1:     Crystal 20MHz(16MHz/12MHz)
diff --git a/converter/ps2_usb/config.h b/converter/ps2_usb/config.h
deleted file mode 100644
index c0a4fab13b..0000000000
--- a/converter/ps2_usb/config.h
+++ /dev/null
@@ -1,173 +0,0 @@
-/*
-Copyright 2012 Jun Wako <wakojun@gmail.com>
-
-This program is free software: you can redistribute it and/or modify
-it under the terms of the GNU General Public License as published by
-the Free Software Foundation, either version 2 of the License, or
-(at your option) any later version.
-
-This program is distributed in the hope that it will be useful,
-but WITHOUT ANY WARRANTY; without even the implied warranty of
-MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
-GNU General Public License for more details.
-
-You should have received a copy of the GNU General Public License
-along with this program.  If not, see <http://www.gnu.org/licenses/>.
-*/
-
-#ifndef CONFIG_H
-#define CONFIG_H
-
-#include <avr/interrupt.h>
-
-#define VENDOR_ID       0xFEED
-#define PRODUCT_ID      0x6512
-#define DEVICE_VER      0x0001
-#define MANUFACTURER    t.m.k.
-#define PRODUCT         PS/2 keyboard converter
-#define DESCRIPTION     convert PS/2 keyboard to USB
-
-
-/* matrix size */
-#define MATRIX_ROWS 32  // keycode bit: 3-0
-#define MATRIX_COLS 8   // keycode bit: 6-4
-
-
-/* key combination for command */
-#define IS_COMMAND() ( \
-    keyboard_report->mods == (MOD_BIT(KC_LSHIFT) | MOD_BIT(KC_RSHIFT)) || \
-    keyboard_report->mods == (MOD_BIT(KC_LCTRL) | MOD_BIT(KC_RSHIFT)) \
-)
-
-
-//#define NO_SUSPEND_POWER_DOWN
-
-
-/*
- * PS/2 Busywait
- */
-#ifdef PS2_USE_BUSYWAIT
-#define PS2_CLOCK_PORT  PORTD
-#define PS2_CLOCK_PIN   PIND
-#define PS2_CLOCK_DDR   DDRD
-#define PS2_CLOCK_BIT   1
-#define PS2_DATA_PORT   PORTD
-#define PS2_DATA_PIN    PIND
-#define PS2_DATA_DDR    DDRD
-#define PS2_DATA_BIT    0
-#endif
-
-/*
- * PS/2 Pin interrupt
- */
-#ifdef PS2_USE_INT
-/* uses INT1 for clock line(ATMega32U4) */
-#define PS2_CLOCK_PORT  PORTD
-#define PS2_CLOCK_PIN   PIND
-#define PS2_CLOCK_DDR   DDRD
-#define PS2_CLOCK_BIT   1
-#define PS2_DATA_PORT   PORTD
-#define PS2_DATA_PIN    PIND
-#define PS2_DATA_DDR    DDRD
-#define PS2_DATA_BIT    0
-#define PS2_INT_INIT()  do {    \
-    EICRA |= ((1<<ISC11) |      \
-              (0<<ISC10));      \
-} while (0)
-#define PS2_INT_ON()  do {      \
-    EIMSK |= (1<<INT1);         \
-} while (0)
-#define PS2_INT_OFF() do {      \
-    EIMSK &= ~(1<<INT1);        \
-} while (0)
-#define PS2_INT_VECT    INT1_vect
-#endif
-
-/*
- * PS/2 USART
- */
-#ifdef PS2_USE_USART
-#if defined(__AVR_ATmega16U4__) || defined(__AVR_ATmega32U4__)
-/* XCK for clock line and RXD for data line */
-#define PS2_CLOCK_PORT  PORTD
-#define PS2_CLOCK_PIN   PIND
-#define PS2_CLOCK_DDR   DDRD
-#define PS2_CLOCK_BIT   5
-#define PS2_DATA_PORT   PORTD
-#define PS2_DATA_PIN    PIND
-#define PS2_DATA_DDR    DDRD
-#define PS2_DATA_BIT    2
-/* synchronous, odd parity, 1-bit stop, 8-bit data, sample at falling edge */
-/* set DDR of CLOCK as input to be slave */
-#define PS2_USART_INIT() do {   \
-    PS2_CLOCK_DDR &= ~(1<<PS2_CLOCK_BIT);   \
-    PS2_DATA_DDR &= ~(1<<PS2_DATA_BIT);     \
-    UCSR1C = ((1 << UMSEL10) |  \
-              (3 << UPM10)   |  \
-              (0 << USBS1)   |  \
-              (3 << UCSZ10)  |  \
-              (0 << UCPOL1));   \
-    UCSR1A = 0;                 \
-    UBRR1H = 0;                 \
-    UBRR1L = 0;                 \
-} while (0)
-#define PS2_USART_RX_INT_ON() do {  \
-    UCSR1B = ((1 << RXCIE1) |       \
-              (1 << RXEN1));        \
-} while (0)
-#define PS2_USART_RX_POLL_ON() do { \
-    UCSR1B = (1 << RXEN1);          \
-} while (0)
-#define PS2_USART_OFF() do {    \
-    UCSR1C = 0;                 \
-    UCSR1B &= ~((1 << RXEN1) |  \
-                (1 << TXEN1));  \
-} while (0)
-#define PS2_USART_RX_READY      (UCSR1A & (1<<RXC1))
-#define PS2_USART_RX_DATA       UDR1
-#define PS2_USART_ERROR         (UCSR1A & ((1<<FE1) | (1<<DOR1) | (1<<UPE1)))
-#define PS2_USART_RX_VECT       USART1_RX_vect
-#elif defined(__AVR_ATmega168__) || defined(__AVR_ATmega168P__) || defined(__AVR_ATmega328P__)
-/* XCK for clock line and RXD for data line */
-#define PS2_CLOCK_PORT  PORTD
-#define PS2_CLOCK_PIN   PIND
-#define PS2_CLOCK_DDR   DDRD
-#define PS2_CLOCK_BIT   4
-#define PS2_DATA_PORT   PORTD
-#define PS2_DATA_PIN    PIND
-#define PS2_DATA_DDR    DDRD
-#define PS2_DATA_BIT    0
-/* synchronous, odd parity, 1-bit stop, 8-bit data, sample at falling edge */
-/* set DDR of CLOCK as input to be slave */
-#define PS2_USART_INIT() do {   \
-    PS2_CLOCK_DDR &= ~(1<<PS2_CLOCK_BIT);   \
-    PS2_DATA_DDR &= ~(1<<PS2_DATA_BIT);     \
-    UCSR0C = ((1 << UMSEL00) |  \
-              (3 << UPM00)   |  \
-              (0 << USBS0)   |  \
-              (3 << UCSZ00)  |  \
-              (0 << UCPOL0));   \
-    UCSR0A = 0;                 \
-    UBRR0H = 0;                 \
-    UBRR0L = 0;                 \
-} while (0)
-#define PS2_USART_RX_INT_ON() do {  \
-    UCSR0B = ((1 << RXCIE0) |       \
-              (1 << RXEN0));        \
-} while (0)
-#define PS2_USART_RX_POLL_ON() do { \
-    UCSR0B = (1 << RXEN0);          \
-} while (0)
-#define PS2_USART_OFF() do {    \
-    UCSR0C = 0;                 \
-    UCSR0B &= ~((1 << RXEN0) |  \
-                (1 << TXEN0));  \
-} while (0)
-#define PS2_USART_RX_READY      (UCSR0A & (1<<RXC0))
-#define PS2_USART_RX_DATA       UDR0
-#define PS2_USART_ERROR         (UCSR0A & ((1<<FE0) | (1<<DOR0) | (1<<UPE0)))
-#define PS2_USART_RX_VECT       USART_RX_vect
-#endif
-#endif
-
-#endif
diff --git a/converter/ps2_usb/config_mbed.h b/converter/ps2_usb/config_mbed.h
deleted file mode 100644
index 5819763e65..0000000000
--- a/converter/ps2_usb/config_mbed.h
+++ /dev/null
@@ -1,60 +0,0 @@
-/*
-Copyright 2012 Jun Wako <wakojun@gmail.com>
-
-This program is free software: you can redistribute it and/or modify
-it under the terms of the GNU General Public License as published by
-the Free Software Foundation, either version 2 of the License, or
-(at your option) any later version.
-
-This program is distributed in the hope that it will be useful,
-but WITHOUT ANY WARRANTY; without even the implied warranty of
-MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
-GNU General Public License for more details.
-
-You should have received a copy of the GNU General Public License
-along with this program.  If not, see <http://www.gnu.org/licenses/>.
-*/
-
-#ifndef CONFIG_MBED_H
-#define CONFIG_MBED_H
-
-
-#if 0
-// duplicated name against mbed USBDeivce
-#define VENDOR_ID       0xFEED
-#define PRODUCT_ID      0x6512
-#endif
-#define DEVICE_VER      0x0001
-#define MANUFACTURER    t.m.k.
-#define PRODUCT         PS/2 keyboard converter
-#define DESCRIPTION     convert PS/2 keyboard to USB
-
-
-/* matrix size */
-#define MATRIX_ROWS 32  // keycode bit: 3-0
-#define MATRIX_COLS 8   // keycode bit: 6-4
-
-
-/* key combination for command */
-#define IS_COMMAND() ( \
-    keyboard_report->mods == (MOD_BIT(KC_LSHIFT) | MOD_BIT(KC_RSHIFT)) || \
-    keyboard_report->mods == (MOD_BIT(KC_LCTRL) | MOD_BIT(KC_RSHIFT)) \
-)
-
-
-/*
- * PS/2 Busywait
- */
-#ifdef PS2_USE_BUSYWAIT
-#   define PS2_CLOCK_PORT  PORTD
-#   define PS2_CLOCK_PIN   PIND
-#   define PS2_CLOCK_DDR   DDRD
-#   define PS2_CLOCK_BIT   5
-#   define PS2_DATA_PORT   PORTD
-#   define PS2_DATA_PIN    PIND
-#   define PS2_DATA_DDR    DDRD
-#   define PS2_DATA_BIT    2
-#endif
-
-
-#endif
diff --git a/converter/ps2_usb/config_tmk_rev1.h b/converter/ps2_usb/config_tmk_rev1.h
deleted file mode 100644
index 75dc97df38..0000000000
--- a/converter/ps2_usb/config_tmk_rev1.h
+++ /dev/null
@@ -1,147 +0,0 @@
-/*
-Copyright 2012 Jun Wako <wakojun@gmail.com>
-
-This program is free software: you can redistribute it and/or modify
-it under the terms of the GNU General Public License as published by
-the Free Software Foundation, either version 2 of the License, or
-(at your option) any later version.
-
-This program is distributed in the hope that it will be useful,
-but WITHOUT ANY WARRANTY; without even the implied warranty of
-MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
-GNU General Public License for more details.
-
-You should have received a copy of the GNU General Public License
-along with this program.  If not, see <http://www.gnu.org/licenses/>.
-*/
-
-#ifndef CONFIG_H
-#define CONFIG_H
-
-#include <avr/interrupt.h>
-
-#define VENDOR_ID       0xFEED
-#define PRODUCT_ID      0x6512
-#define DEVICE_VER      0x0001
-#define MANUFACTURER    t.m.k.
-#define PRODUCT         PS/2 keyboard converter
-#define DESCRIPTION     convert PS/2 keyboard to USB
-
-
-/* matrix size */
-#define MATRIX_ROWS 32  // keycode bit: 3-0
-#define MATRIX_COLS 8   // keycode bit: 6-4
-
-
-/* key combination for command */
-#define IS_COMMAND() ( \
-    keyboard_report->mods == (MOD_BIT(KC_LSHIFT) | MOD_BIT(KC_RSHIFT)) || \
-    keyboard_report->mods == (MOD_BIT(KC_LCTRL) | MOD_BIT(KC_RSHIFT)) \
-)
-
-
-//#define NO_SUSPEND_POWER_DOWN
-
-
-/*
- * PS/2 Busywait
- */
-#ifdef PS2_USE_BUSYWAIT
-#define PS2_CLOCK_PORT  PORTD
-#define PS2_CLOCK_PIN   PIND
-#define PS2_CLOCK_DDR   DDRD
-#define PS2_CLOCK_BIT   5
-#define PS2_DATA_PORT   PORTD
-#define PS2_DATA_PIN    PIND