cleans up folder structure

* consolidates docs
* deletes converter/
* updates .md references (most)

12 files changed, 0 insertions, 972 deletions

diff --git a/converter/ibm4704_usb/Makefile b/converter/ibm4704_usb/Makefile
deleted file mode 100644
index b5c97d2d31..0000000000
--- a/converter/ibm4704_usb/Makefile
+++ /dev/null
@@ -1,93 +0,0 @@
-# Target file name (without extension).
-TARGET = ibm4704_usb
-
-# Directory common source filess exist
-TMK_DIR = ../../tmk_core
-
-# Directory keyboard dependent files exist
-TARGET_DIR = .
-
-# project specific files
-SRC =	keymap_common.c \
-	matrix.c \
-	led.c \
-	protocol/ibm4704.c
-
-ifdef KEYMAP
-    SRC := keymap_$(KEYMAP).c $(SRC)
-else
-    SRC := keymap_plain.c $(SRC)
-endif
-
-CONFIG_H = config.h
-
-
-# MCU name
-#MCU = at90usb1287
-MCU = atmega32u4
-
-# Processor frequency.
-#     This will define a symbol, F_CPU, in all source code files equal to the
-#     processor frequency in Hz. You can then use this symbol in your source code to
-#     calculate timings. Do NOT tack on a 'UL' at the end, this will be done
-#     automatically to create a 32-bit value in your source code.
-#
-#     This will be an integer division of F_USB below, as it is sourced by
-#     F_USB after it has run through any CPU prescalers. Note that this value
-#     does not *change* the processor frequency - it should merely be updated to
-#     reflect the processor speed set externally so that the code can use accurate
-#     software delays.
-F_CPU = 16000000
-
-
-#
-# LUFA specific
-#
-# Target architecture (see library "Board Types" documentation).
-ARCH = AVR8
-
-# Input clock frequency.
-#     This will define a symbol, F_USB, in all source code files equal to the
-#     input clock frequency (before any prescaling is performed) in Hz. This value may
-#     differ from F_CPU if prescaling is used on the latter, and is required as the
-#     raw input clock is fed directly to the PLL sections of the AVR for high speed
-#     clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
-#     at the end, this will be done automatically to create a 32-bit value in your
-#     source code.
-#
-#     If no clock division is performed on the input clock inside the AVR (via the
-#     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
-F_USB = $(F_CPU)
-
-# Interrupt driven control endpoint task(+60)
-OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
-
-
-# Boot Section Size in *bytes*
-#   Teensy halfKay   512
-#   Teensy++ halfKay 1024
-#   Atmel DFU loader 4096
-#   LUFA bootloader  4096
-#   USBaspLoader     2048
-OPT_DEFS += -DBOOTLOADER_SIZE=4096
-
-
-# Build Options
-#   comment out to disable the options.
-#
-#BOOTMAGIC_ENABLE = yes	# Virtual DIP switch configuration(+1000)
-MOUSEKEY_ENABLE = yes	# Mouse keys(+4700)
-EXTRAKEY_ENABLE = yes	# Audio control and System control(+450)
-CONSOLE_ENABLE = yes	# Console for debug(+400)
-COMMAND_ENABLE = yes    # Commands for debug and configuration
-#NKRO_ENABLE = yes	# USB Nkey Rollover - not yet supported in LUFA
-
-
-# Search Path
-VPATH += $(TARGET_DIR)
-VPATH += $(TMK_DIR)
-
-include $(TMK_DIR)/protocol.mk
-include $(TMK_DIR)/protocol/lufa.mk
-include $(TMK_DIR)/common.mk
-include $(TMK_DIR)/rules.mk
diff --git a/converter/ibm4704_usb/README.md b/converter/ibm4704_usb/README.md
deleted file mode 100644
index 68db4bd050..0000000000
--- a/converter/ibm4704_usb/README.md
+++ /dev/null
@@ -1,72 +0,0 @@
-IBM 4704 to USB keyboard converter
-==================================
-This firmware converts IBM 4704 keyboard protocol to USB HID.
-
-Keyboard initialization process takes a few seconds at start up. During that you will hear buzzer from the keyboard. **You need to plug USB cable after hooking up your keyboard to the converter.**
-
-
-Update
-------
-2015/09/07  Added keymap for Alps 102-key. Thanks, tai @ geekhack!
-2015/05/05  Added keymaps for 107-key, 77-key and 50-key. Thanks, orihalcon @ geekhack!
-2015/05/19  Fixed a protocol handling bug.
-
-
-
-Supported Keyboard
-------------------
-### IBM capacitive switch models:
-- 6019273 Model 100 50-key (grid layout)      http://kishy.ca/?p=894
-- 6019284 Model 200 62-key Alpha(60% layout)  http://kishy.ca/?p=894
-- 6019303 Model 300 77-key Expanded Alpha     http://deskthority.net/photos-f62/ibm-6019303-t8502.html
-- 6020218 Model 400 107-key Full key          http://kishy.ca/?p=894
-
-### Alps switch(vintage Green) models:
-
-- 5954339 Japanese 102-key    http://deskthority.net/post87127.html#p87127
-- 6112883 Japanese 102-key    http://geekhack.org/index.php?topic=52888.msg1194489#msg1194489
-- 6112884 Japanese 102-key    http://geekhack.org/index.php?topic=50437.msg1193047#msg1193047
-- 6341739 Chinese 102-key     http://geekhack.org/index.php?topic=52888.msg1176566#msg1176566
-
-
-Connector
----------
-Keyboard Plug from front:
-
-    DSUB-9
-    -------------
-    \ N 2 3 4 5 /
-     \ N N N N /
-      ---------
-    2   GND
-    3   VCC 5V
-    4   DATA
-    5   CLOCK
-    N   No connection/No pin.
-
-
-Connection
-----------
-In case of using ATMega32U4(Teensy2.0):
-
-1. Supply power with VCC and GND.
-2. Connect CLOCK to PD1 and DATA to PD0. You can change pin with config.h.
-3. Optionally you may need pull-up register. 1KOhm probably work.
-
-
-Build Firmware
---------------
-Just run `make`:
-
-    $ make
-
-To select keymap:
-
-    $ make KEYMAP=[plain|...]
-
-
-Keymap
-------
-Several version of keymap are available in advance but you are recommended to define your favorite layout yourself. To define your own keymap create file named `keymap_<name>.c` and see keymap document(you can find in top README.md) and existent keymap files.
-
-Use `KEYMAP_ALPS102()` to define your keymap for Alps models.
diff --git a/converter/ibm4704_usb/config.h b/converter/ibm4704_usb/config.h
deleted file mode 100644
index 2fee10fd61..0000000000
--- a/converter/ibm4704_usb/config.h
+++ /dev/null
@@ -1,61 +0,0 @@
-/*
-Copyright 2014 Jun Wako <wakojun@gmail.com>
-
-This program is free software: you can redistribute it and/or modify
-it under the terms of the GNU General Public License as published by
-the Free Software Foundation, either version 2 of the License, or
-(at your option) any later version.
-
-This program is distributed in the hope that it will be useful,
-but WITHOUT ANY WARRANTY; without even the implied warranty of
-MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
-GNU General Public License for more details.
-
-You should have received a copy of the GNU General Public License
-along with this program.  If not, see <http://www.gnu.org/licenses/>.
-*/
-
-#ifndef CONFIG_H
-#define CONFIG_H
-
-#include <avr/interrupt.h>
-
-#define VENDOR_ID       0xFEED
-#define PRODUCT_ID      0x4707
-#define DEVICE_VER      0x0001
-#define MANUFACTURER    t.m.k.
-#define PRODUCT         IBM 4704 keyboard converter
-#define DESCRIPTION     convert IBM 4704 keyboard to USB
-
-
-/* matrix size */
-#define MATRIX_ROWS 16  // keycode bit3-6 
-#define MATRIX_COLS 8   // keycode bit0-2
-
-
-/* key combination for command */
-#define IS_COMMAND() ( \
-    keyboard_report->mods == (MOD_BIT(KC_LCTRL) | MOD_BIT(KC_RCTRL)) || \
-    keyboard_report->mods == (MOD_BIT(KC_LSHIFT) | MOD_BIT(KC_RSHIFT)) \
-)
-
-
-
-/* Pin configuration */
-#define IBM4704_CLOCK_PORT  PORTD
-#define IBM4704_CLOCK_PIN   PIND
-#define IBM4704_CLOCK_DDR   DDRD
-#define IBM4704_CLOCK_BIT   1
-#define IBM4704_DATA_PORT   PORTD
-#define IBM4704_DATA_PIN    PIND
-#define IBM4704_DATA_DDR    DDRD
-#define IBM4704_DATA_BIT    0
-
-/* Pin interrupt on rising edge of clock */
-#define IBM4704_INT_INIT()  do { EICRA |= ((1<<ISC11)|(1<<ISC10)); } while (0)
-#define IBM4704_INT_ON()    do { EIFR |= (1<<INTF1); EIMSK |= (1<<INT1); } while (0)
-#define IBM4704_INT_OFF()   do { EIMSK &= ~(1<<INT1); } while (0)
-#define IBM4704_INT_VECT    INT1_vect
-
-
-#endif
diff --git a/converter/ibm4704_usb/ibm4704.txt b/converter/ibm4704_usb/ibm4704.txt
deleted file mode 100644
index e2d42f08fd..0000000000
--- a/converter/ibm4704_usb/ibm4704.txt
+++ /dev/null
@@ -1,182 +0,0 @@
-IBM 4704 Keyboard
-=================
-IBM capacitive switch models:
-    6019273 Model 100 50-key (grid layout)      http://kishy.ca/?p=894
-    6019284 Model 200 62-key Alpha(60% layout)  http://kishy.ca/?p=894
-    6019303 Model 300 77-key Expanded Alpha     http://deskthority.net/photos-f62/ibm-6019303-t8502.html
-    6020218 Model 400 107-key Full key          http://kishy.ca/?p=894
-
-Alps switch(vintage Green) models:
-    5954339 Japanese 102-key    http://deskthority.net/post87127.html#p87127
-    6112883 Japanese 102-key    http://geekhack.org/index.php?topic=52888.msg1194489#msg1194489
-    6112884 Japanese 102-key    http://geekhack.org/index.php?topic=50437.msg1193047#msg1193047
-    6341739 Chinese 102-key     http://geekhack.org/index.php?topic=52888.msg1176566#msg1176566
-
-Resourse
---------
-The IBM 4704: lots of pictures and info
-http://kishy.dyndns.org/?p=648#more-648 
-
-Brochure:
-http://ed-thelen.org/comp-hist/IBM-ProdAnn/4700.pdf
-
-
-
-IBM 4704 Keyboard Protocol
-==========================
-On powering up keyboard sends keyboard ID; A3h for 6019284(62-key), for example.
-After that the keyboard enters FC command mode and waits for parameter data from host
-so that it doesn't send any scancode until you send 'FF'(End of FC command mode).
-
-    Keyboard                    ID
-    -------------------------------
-    Model 100 50-key            A2h
-    Model 200 62-key            A3h
-    Model 300 77-key            A4h
-    Model 400 107-key           A5h
-    Japanese/Chinese 102-key    A6h
-
-
-Connector
----------
-    Keyboard Plug from front
-
-    DSUB-9
-    -------------
-    \ N 2 3 4 5 /
-     \ N N N N /
-      ---------
-    2   GND
-    3   VCC 5V
-    4   DATA
-    5   CLOCK
-    N   No connection/No pin.
-
-
-Keyboard to Host
-----------------
-Data bits are LSB first and Pairty is odd. Clock has around 60us high and 30us low part.
-
-            ____       __   __   __   __   __   __   __   __   __   _______
-    Clock       \_____/  \_/  \_/  \_/  \_/  \_/  \_/  \_/  \_/  \_/
-                 ____ ____ ____ ____ ____ ____ ____ ____ ____ ____    
-    Data    ____/    X____X____X____X____X____X____X____X____X____X________
-                Start   0    1    2    3    4    5    6    7    P  Stop
-
-Start bit:  can be long as 300-350us.
-Inhibit:    Pull Data line down to inhibit keyboard to send.
-Timing:     Host reads bit while Clock is hi.(rising edge)
-Stop bit:   Keyboard pulls down Data line to lo after 9th clock.
-
-
-Host to Keyboard
-----------------
-Data bits are LSB first and Pairty is odd. Clock has around 60us high and 30us low part.
-
-            ____        __   __   __   __   __   __   __   __   __   ________
-    Clock       \______/  \_/  \_/  \_/  \_/  \_/  \_/  \_/  \_/  \_/
-                ^   ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ___
-    Data    ____|__/    X____X____X____X____X____X____X____X____X____X   \___
-                |  Start   0    1    2    3    4    5    6    7    P   Stop
-                Request by host
-
-Start bit:  can be long as 300-350us.
-Request:    Host pulls Clock line down to request to send a command.
-Timing:     After Request keyboard pull up Data and down Clock line to low for start bit.
-            After request host release Clock line once Data line becomes hi.
-            Host wirtes a bit while Clock is hi and Keyboard reads while low.
-Stop bit:   Host releases or pulls up Data line to hi after 9th clock and waits for keybaord pull down the line to lo.
-
-
-Scancodes
----------
-Keyboard doesn't send Break code for all keys except for Alt by default.
-
-    6019284 62-key:
-    ,-----------------------------------------------------------.
-    |  `|  1|  2|  3|  4|  5|  6|  7|  8|  9|  0|  -|  =|???|BS |
-    |-----------------------------------------------------------|
-    |Tab  |  Q|  W|  E|  R|  T|  Y|  U|  I|  O|  P| ￠|  \|  PD2|
-    |-----------------------------------------------------------|
-    |Ctrl  |  A|  S|  D|  F|  G|  H|  J|  K|  L|  ;|  '| {}| PD3|
-    |-----------------------------------------------------------|
-    |Shif| <>|  Z|  X|  C|  V|  B|  N|  M|  ,|  ,|  /|???|Shift |
-    |-----------------------------------------------------------|
-    |Reset|blk|Alt  |         Space             |Alt  |blk|Enter|
-    `-----------------------------------------------------------'
-    +----------+---------------------+----------+----------+
-    |`       00|PD1     04|Caps    20|LShift  30|Reset   31|
-    |1       18|q       05|a       21|<>      3E|Rblank  41|
-    |2       19|w       06|s       22|z       32|Alt     3F|
-    |3       1A|e       13|d       23|x       33|Space   40|
-    |4       10|r       14|f       24|c       34|Alt     3F|
-    |5       11|t       15|g       25|v       35|Lblank  42|
-    |6       12|y       16|h       26|b       36|Enter   2F|
-    |7       08|u       17|j       27|n       37|          |
-    |8       09|i       01|k       28|m       38|          |
-    |9       0A|o       02|l       29|,       39|          |
-    |0       0F|p       03|;       2A|.       3A|          |
-    |-       1F|￠      1B|'       2B|/       3B|          |
-    |=       0D|\       1C|{}      2C|???     3C|          |
-    |???     0C|PD2     1D|PD3     2D|RShift  3D|          |
-    |BS      0E|          |          |          |          |
-    +----------+---------------------+----------+----------+
-    Bit7 is 'press flag' which set 1 on press and 0 on release when break code is enabled.
-
-NOTE: When break code is enabled the key sends scancode with setting 7th bit on press
-and without it on release. That is, '`' sends 80h on press and 00h on release.
-
-
-Keyboard command
-----------------
-Keyboard accepts these commands from host.
-
-        Description                             Entry point
-    -----------------------------------------------------------
-    FF  Soft Reset                              0008h
-    FE  Resend                                  00e8h
-    FD  Buzzer(emits a short beep)              00edh
-    FC  Set Key Flag                            00f6h
-    FB  Soft Reset                              0008h
-    FA  Reset                                   0000h
-    
-
-Keyboard response
------------------
-Keyobard sends these bytes to host.
-
-        Description                             Entry point
-    -----------------------------------------------------------
-    FE  Overflow(key event/receive data)        00c5h, 0346h
-        Memory test error                       0224h
-    FD  Command out of bound                    00d8h
-        Key out of bound
-    7E  Read/Parity error in receive from host  00bch
-
-
-Set Key Flag command(FC)
-------------------------
-After 'Power on Reset' firmware enters this command mode and waits for data from host,
-so that you don't need to send 'FC' and it doesn't send any scancode until you send 'FF'.
-
-Data sent from host:
-
-    bit: 7   6 ... 0
-         en  |     |
-         |   `-----`--- scan code
-         `------------- enable bit(0: enable repeat, 1: enable break)
-
-    00-79   Enable repeat
-    80-F9   Enable break(FA-FF are used as other commands, see above.)
-    FE      Resend(011ah) no need to use
-    FF      End(0114h) exits FC command mode.
-
-Response from keyboard:
-    FD      Out of bound - Invalid scancode
-    --      OK - No response means that command is accepted.
-
-Examples:
-    To enable break code of all keys.
-
-    FC 80 81 ... F7 FF
-
diff --git a/converter/ibm4704_usb/keymap_50key.c b/converter/ibm4704_usb/keymap_50key.c
deleted file mode 100644
index 97294fb45d..0000000000
--- a/converter/ibm4704_usb/keymap_50key.c
+++ /dev/null
@@ -1,17 +0,0 @@
-#include "keymap_common.h"
-
-
-const uint8_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = {
-    KEYMAP_50(
-    F1,  F2,  F3,   F4,  F5,  F6,   F7,  F8,  F9,  F10,  \
-    1,   2,   3,    4,   5,   6,    7,   8,   9,   0,    \
-    Q,   W,   E,    R,   T,   Y,    U,   I,   O,   P,    \
-    A,   S,   D,    F,   G,   H,    J,   K,   L,   SCLN, \
-    Z,   X,   C,    V,   B,   N,    M,   COMM,DOT, SLSH  \
-    ),
-};
-
-const uint16_t PROGMEM fn_actions[] = {
-};
-
-
diff --git a/converter/ibm4704_usb/keymap_alps102key.c b/converter/ibm4704_usb/keymap_alps102key.c
deleted file mode 100644
index f3dda718ac..0000000000
--- a/converter/ibm4704_usb/keymap_alps102key.c
+++ /dev/null
@@ -1,50 +0,0 @@
-#include "keymap_common.h"
-
-
-const uint8_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = {
-    /* Layer 0:
-     * ,---------------------------------------------------------------.  ,-----------. ,---------------.
-     * |  `|  1|  2|  3|  4|  5|  6|  7|  8|  9|  0|  -|  =|BS |BS |F21|  |PSC|SLK|PAU| |F1 |F2 |F3 |F4 |
-     * |---------------------------------------------------------------|  |-----------| |---------------|
-     * |Tab  |  Q|  W|  E|  R|  T|  Y|  U|  I|  O|  P|  [|  ]|    \|F22|  |Ins|Hom|PgU| |F5 |F6 |F7 |F8 |
-     * |---------------------------------------------------------------|  |-----------| |---------------|
-     * |Ctrl  |  A|  S|  D|  F|  G|  H|  J|  K|  L|  ;|  '|Ret|Ret |F23|  |Del|End|PgD| |F9 |F10|F11|F12|
-     * |---------------------------------------------------------------|  |-----------| |---------------|
-     * |Shift   |  Z|  X|  C|  V|  B|  N|  M|  ,|  ,|  /|Shf|Shift |F24|  |   |Up |   | |F13|F14|F15|F16|
-     * |---------------------------------------------------------------|  |-----------| |---------------|
-     * |Fn0  |Gui|Alt  |         Space             |Alt* |Gui|Fn0      |  |Lef|Dow|Rig| |F17|F18|F19|F20|
-     * `---------------------------------------------------------------'  `-----------' `---------------'
-     */
-    KEYMAP_ALPS102(
-    ESC, 1,   2,   3,   4,   5,   6,   7,   8,   9,   0,   MINS,EQL, BSPC,BSPC,F21,      PSCR,SLCK,PAUS,     F1,  F2,  F3,  F4,  \
-    TAB, Q,   W,   E,   R,   T,   Y,   U,   I,   O,   P,   LBRC,RBRC,BSLS,     F22,      INS, HOME,PGUP,     F5,  F6,  F7,  F8,  \
-    LCTL,A,   S,   D,   F,   G,   H,   J,   K,   L,   SCLN,QUOT,GRV, ENT,      F23,      DEL, END, PGDN,     F9,  F10, F11, F12, \
-    LSFT,Z,   X,   C,   V,   B,   N,   M,   COMM,DOT, SLSH,RSFT,RSFT,          F24,      NO,  UP,  NO,       F13, F14, F15, F16, \
-    FN0, LGUI,LALT,          SPC,                     RALT,RGUI,               FN0,      LEFT,DOWN,RGHT,     F17, F18, F19, F20  \
-    ),
-
-    /* Layer 1:
-     * ,---------------------------------------------------------------.  ,-----------. ,---------------.
-     * |  `|  1|  2|  3|  4|  5|  6|  7|  8|  9|  0|  -|  =|BS |BS |F21|  |VoD|VoU|Mut| |F1 |F2 |F3 |F4 |
-     * |---------------------------------------------------------------|  |-----------| |---------------|
-     * |Tab  |  Q|  W|  E|  R|  T|  Y|  U|  I|  O|  P|  [|  ]|    \|F22|  |Ins|Hom|PgU| |F5 |F6 |F7 |F8 |
-     * |---------------------------------------------------------------|  |-----------| |---------------|
-     * |Ctrl  |  A|  S|  D|  F|  G|  H|  J|  K|  L|  ;|  '|Ret|Ret |F23|  |Del|End|PgD| |F9 |F10|F11|F12|
-     * |---------------------------------------------------------------|  |-----------| |---------------|
-     * |Shift   |  Z|  X|  C|  V|  B|  N|  M|  ,|  ,|  /|Shf|Shift |F24|  |   |PgU|   | |F13|F14|F15|F16|
-     * |---------------------------------------------------------------|  |-----------| |---------------|
-     * |Fn0  |Gui|Alt  |         Space             |Alt* |Gui|Fn0      |  |Hom|PgD|End| |F17|F18|F19|F20|
-     * `---------------------------------------------------------------'  `-----------' `---------------'
-     */
-    KEYMAP_ALPS102(
-    TRNS,TRNS,TRNS,TRNS,TRNS,TRNS,TRNS,TRNS,TRNS,TRNS,TRNS,TRNS,TRNS,TRNS,TRNS,TRNS,     VOLD,VOLU,MUTE,     TRNS,TRNS,TRNS,TRNS, \
-    TRNS,TRNS,TRNS,TRNS,TRNS,TRNS,TRNS,TRNS,TRNS,TRNS,TRNS,TRNS,TRNS,TRNS,     TRNS,     TRNS,TRNS,TRNS,     TRNS,TRNS,TRNS,TRNS, \
-    TRNS,TRNS,TRNS,TRNS,TRNS,TRNS,TRNS,TRNS,TRNS,TRNS,TRNS,TRNS,TRNS,TRNS,     TRNS,     TRNS,TRNS,TRNS,     TRNS,TRNS,TRNS,TRNS, \
-    TRNS,TRNS,TRNS,TRNS,TRNS,TRNS,TRNS,TRNS,TRNS,TRNS,TRNS,TRNS,TRNS,          TRNS,     TRNS,PGUP,TRNS,     TRNS,TRNS,TRNS,TRNS, \
-    TRNS,TRNS,TRNS,          TRNS,                    TRNS,TRNS,               TRNS,     HOME,PGDN,END,      TRNS,TRNS,TRNS,TRNS  \
-    ),
-};
-
-const uint16_t PROGMEM fn_actions[] = {
-    [0] = ACTION_LAYER_MOMENTARY(1),
-};
diff --git a/converter/ibm4704_usb/keymap_common.c b/converter/ibm4704_usb/keymap_common.c
deleted file mode 100644
index 55a13793cb..0000000000
--- a/converter/ibm4704_usb/keymap_common.c
+++ /dev/null
@@ -1,30 +0,0 @@
-/*
-Copyright 2011,2012,2013 Jun Wako <wakojun@gmail.com>
-
-This program is free software: you can redistribute it and/or modify
-it under the terms of the GNU General Public License as published by
-the Free Software Foundation, either version 2 of the License, or
-(at your option) any later version.
-
-This program is distributed in the hope that it will be useful,
-but WITHOUT ANY WARRANTY; without even the implied warranty of
-MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
-GNU General Public License for more details.
-
-You should have received a copy of the GNU General Public License
-along with this program.  If not, see <http://www.gnu.org/licenses/>.
-*/
-#include "keymap_common.h"
-
-
-/* translates key to keycode */
-uint8_t keymap_key_to_keycode(uint8_t layer, keypos_t key)
-{
-    return pgm_read_byte(&keymaps[(layer)][(key.row)][(key.col)]);
-}
-
-/* translates Fn keycode to action */
-action_t keymap_fn_to_action(uint8_t keycode)
-{
-    return (action_t){ .code = pgm_read_word(&fn_actions[FN_INDEX(keycode)]) };
-}
diff --git a/converter/ibm4704_usb/keymap_common.h b/converter/ibm4704_usb/keymap_common.h
deleted file mode 100644
index 9cb23b0b83..0000000000
--- a/converter/ibm4704_usb/keymap_common.h
+++ /dev/null
@@ -1,146 +0,0 @@
-/*
-Copyright 2011,2012,2013 Jun Wako <wakojun@gmail.com>
-
-This program is free software: you can redistribute it and/or modify
-it under the terms of the GNU General Public License as published by
-the Free Software Foundation, either version 2 of the License, or
-(at your option) any later version.
-
-This program is distributed in the hope that it will be useful,
-but WITHOUT ANY WARRANTY; without even the implied warranty of
-MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
-GNU General Public License for more details.
-
-You should have received a copy of the GNU General Public License
-along with this program.  If not, see <http://www.gnu.org/licenses/>.
-*/
-#ifndef KEYMAP_COMMON_H
-#define KEYMAP_COMMON_H
-
-#include <stdint.h>
-#include <stdbool.h>
-#include <avr/pgmspace.h>
-#include "keycode.h"
-#include "action.h"
-#include "action_macro.h"
-#include "report.h"
-#include "print.h"
-#include "debug.h"
-#include "keymap.h"
-
-
-// 32*8(256) byte array which converts PS/2 code into USB code
-extern const uint8_t keymaps[][MATRIX_ROWS][MATRIX_COLS];
-extern const uint16_t fn_actions[];
-
-
-/* 107-key */
-#define KEYMAP( \
-    K46,K64,     K00,K18,K19,K1A,K10,K11,K12,K08,K09,K0A,K0F,K1F,K0D,K0C,K0E,   K6A,K6B,K6C,    K47,K48,K49,K4A, \
-    K56,K66,     K04,K05,K06,K13,K14,K15,K16,K17,K01,K02,K03,K1B,K1C,K1D,       K6D,K6E,K6F,    K4B,K4C,K4D,K4E, \
-    K71,K77,     K20,K21,K22,K23,K24,K25,K26,K27,K28,K29,K2A,K2B,K2C,K2D,       K70,K65,K72,    K50,K51,K52,K53, \
-    K44,K45,     K30,K3E,K32,K33,K34,K35,K36,K37,K38,K39,K3A,K3B,K3C,K3D,       K74,K75,K76,    K5E,K58,K59,K5A, \
-    K54,K55,     K31,K41,K3F,        K40,                        K42,K2F,       K78,K67,K79,    K5B,K5C,K5D,K57  \
-) { \
-    { KC_##K00, KC_##K01, KC_##K02, KC_##K03, KC_##K04, KC_##K05, KC_##K06, KC_NO    }, \
-    { KC_##K08, KC_##K09, KC_##K0A, KC_NO,    KC_##K0C, KC_##K0D, KC_##K0E, KC_##K0F }, \
-    { KC_##K10, KC_##K11, KC_##K12, KC_##K13, KC_##K14, KC_##K15, KC_##K16, KC_##K17 }, \
-    { KC_##K18, KC_##K19, KC_##K1A, KC_##K1B, KC_##K1C, KC_##K1D, KC_NO,    KC_##K1F }, \
-    { KC_##K20, KC_##K21, KC_##K22, KC_##K23, KC_##K24, KC_##K25, KC_##K26, KC_##K27 }, \
-    { KC_##K28, KC_##K29, KC_##K2A, KC_##K2B, KC_##K2C, KC_##K2D, KC_NO,    KC_##K2F }, \
-    { KC_##K30, KC_##K31, KC_##K32, KC_##K33, KC_##K34, KC_##K35, KC_##K36, KC_##K37 }, \
-    { KC_##K38, KC_##K39, KC_##K3A, KC_##K3B, KC_##K3C, KC_##K3D, KC_##K3E, KC_##K3F }, \
-    { KC_##K40, KC_##K41, KC_##K42, KC_NO,    KC_##K44, KC_##K45, KC_##K46, KC_##K47 }, \
-    { KC_##K48, KC_##K49, KC_##K4A, KC_##K4B, KC_##K4C, KC_##K4D, KC_##K4E, KC_NO    }, \
-    { KC_##K50, KC_##K51, KC_##K52, KC_##K53, KC_##K54, KC_##K55, KC_##K56, KC_##K57 }, \
-    { KC_##K58, KC_##K59, KC_##K5A, KC_##K5B, KC_##K5C, KC_##K5D, KC_##K5E, KC_NO    }, \
-    { KC_NO,    KC_NO,    KC_NO,    KC_NO,    KC_##K64, KC_##K65, KC_##K66, KC_##K67 }, \
-    { KC_NO,    KC_NO,    KC_##K6A, KC_##K6B, KC_##K6C, KC_##K6D, KC_##K6E, KC_##K6F }, \
-    { KC_##K70, KC_##K71, KC_##K72, KC_NO,    KC_##K74, KC_##K75, KC_##K76, KC_##K77 }, \
-    { KC_##K78, KC_##K79, KC_NO,    KC_NO,    KC_NO,    KC_NO,    KC_NO,    KC_NO    }  \
-}
-
-/* 77-key */
-#define KEYMAP_77( \
-    K00,K18,K19,K1A,K10,K11,K12,K08,K09,K0A,K0F,K1F,K0D,K0C,K0E,   K6A,K6B,K6C, \
-    K04,K05,K06,K13,K14,K15,K16,K17,K01,K02,K03,K1B,K1C,K1D,       K6D,K6E,K6F, \
-    K20,K21,K22,K23,K24,K25,K26,K27,K28,K29,K2A,K2B,K2C,K2D,       K70,K65,K72, \
-    K30,K3E,K32,K33,K34,K35,K36,K37,K38,K39,K3A,K3B,K3C,K3D,       K74,K75,K76, \
-    K31,K41,K3F,        K40,                        K42,K2F,       K78,K67,K79  \
-) KEYMAP( \
-    F1,  F2,    K00,K18,K19,K1A,K10,K11,K12,K08,K09,K0A,K0F,K1F,K0D,K0C,K0E,    K6A,K6B,K6C,    NLCK,PSLS,PAST,PMNS, \
-    F3,  F4,    K04,K05,K06,K13,K14,K15,K16,K17,K01,K02,K03,K1B,K1C,K1D,        K6D,K6E,K6F,    P7,  P8,  P9,  PPLS, \
-    F5,  F6,    K20,K21,K22,K23,K24,K25,K26,K27,K28,K29,K2A,K2B,K2C,K2D,        K70,K65,K72,    P4,  P5,  P6,  PPLS, \
-    F7,  F8,    K30,K3E,K32,K33,K34,K35,K36,K37,K38,K39,K3A,K3B,K3C,K3D,        K74,K75,K76,    P1,  P2,  P3,  PENT, \
-    F9,  F10,   K31,K41,K3F,        K40,                        K42,K2F,        K78,K67,K79     P0,  P0,  PDOT,PENT  \
-)
-
-/* 62-key */
-#define KEYMAP_62( \
-    K00,K18,K19,K1A,K10,K11,K12,K08,K09,K0A,K0F,K1F,K0D,K0C,K0E, \
-    K04,K05,K06,K13,K14,K15,K16,K17,K01,K02,K03,K1B,K1C,K1D, \
-    K20,K21,K22,K23,K24,K25,K26,K27,K28,K29,K2A,K2B,K2C,K2D, \
-    K30,K3E,K32,K33,K34,K35,K36,K37,K38,K39,K3A,K3B,K3C,K3D, \
-    K31,K41,K3F,        K40,                        K42,K2F  \
-) KEYMAP( \
-    F1,  F2,    K00,K18,K19,K1A,K10,K11,K12,K08,K09,K0A,K0F,K1F,K0D,K0C,K0E,   INS, HOME,PGUP,     NLCK,PSLS,PAST,PMNS, \
-    F3,  F4,    K04,K05,K06,K13,K14,K15,K16,K17,K01,K02,K03,K1B,K1C,K1D,       DEL, END, PGDN,     P7,  P8,  P9,  PPLS, \
-    F5,  F6,    K20,K21,K22,K23,K24,K25,K26,K27,K28,K29,K2A,K2B,K2C,K2D,       PSCR,SLCK,PAUS,     P4,  P5,  P6,  PPLS, \
-    F7,  F8,    K30,K3E,K32,K33,K34,K35,K36,K37,K38,K39,K3A,K3B,K3C,K3D,       F11, UP,  F12,      P1,  P2,  P3,  PENT, \
-    F9,  F10,   K31,K41,K3F,        K40,                        K42,K2F,       LEFT,DOWN,RGHT,     P0,  P0,  PDOT,PENT  \
-)
-
-/* 50-key */
-#define KEYMAP_50( \
-    K00,K01,K02,    K03,K04,K05,    K20,K21,K22,K23, \
-    K08,K09,K0A,    K0B,K0C,K0D,    K28,K29,K2A,K35, \
-    K10,K11,K12,    K13,K14,K15,    K30,K31,K32,K36, \
-    K18,K19,K1A,    K1B,K1C,K1D,    K38,K39,K3A,K37, \
-    K16,K1E,K0E,    K0F,K1F,K17,    K33,K3B,K2B,K3F  \
-) { \
-    { KC_##K00, KC_##K01, KC_##K02, KC_##K03, KC_##K04, KC_##K05, KC_NO,    KC_NO,   }, \
-    { KC_##K08, KC_##K09, KC_##K0A, KC_##K0B, KC_##K0C, KC_##K0D, KC_##K0E, KC_##K0F }, \
-    { KC_##K10, KC_##K11, KC_##K12, KC_##K13, KC_##K14, KC_##K15, KC_##K16, KC_##K17 }, \
-    { KC_##K18, KC_##K19, KC_##K1A, KC_##K1B, KC_##K1C, KC_##K1D, KC_##K1E, KC_##K1F }, \
-    { KC_##K20, KC_##K21, KC_##K22, KC_##K23, KC_NO,    KC_NO,    KC_NO,    KC_NO,   }, \
-    { KC_##K28, KC_##K29, KC_##K2A, KC_##K2B, KC_NO,    KC_NO,    KC_NO,    KC_NO,   }, \
-    { KC_##K30, KC_##K31, KC_##K32, KC_##K33, KC_NO,    KC_##K35, KC_##K36, KC_##K37 }, \
-    { KC_##K38, KC_##K39, KC_##K3A, KC_##K3B, KC_NO,    KC_NO,    KC_NO,    KC_##K3F }, \
-    { KC_NO,    KC_NO,    KC_NO,    KC_NO,    KC_NO,    KC_NO,    KC_NO,    KC_NO,   }, \
-    { KC_NO,    KC_NO,    KC_NO,    KC_NO,    KC_NO,    KC_NO,    KC_NO,    KC_NO,   }, \
-    { KC_NO,    KC_NO,    KC_NO,    KC_NO,    KC_NO,    KC_NO,    KC_NO,    KC_NO,   }, \
-    { KC_NO,    KC_NO,    KC_NO,    KC_NO,    KC_NO,    KC_NO,    KC_NO,    KC_NO,   }, \
-    { KC_NO,    KC_NO,    KC_NO,    KC_NO,    KC_NO,    KC_NO,    KC_NO,    KC_NO,   }, \
-    { KC_NO,    KC_NO,    KC_NO,    KC_NO,    KC_NO,    KC_NO,    KC_NO,    KC_NO,   }, \
-    { KC_NO,    KC_NO,    KC_NO,    KC_NO,    KC_NO,    KC_NO,    KC_NO,    KC_NO,   }, \
-    { KC_NO,    KC_NO,    KC_NO,    KC_NO,    KC_NO,    KC_NO,    KC_NO,    KC_NO,   }  \
-}
-
-/* Alps 102-key */
-#define KEYMAP_ALPS102( \
-    K00, K0F, K01, K02, K03, K04, K05, K06, K07, K08, K09, K0A, K0B, K0C, K0D, K0E,   K44, K45, K46,   K43, K41, K42, K4A, \
-    K10, K11, K12, K13, K14, K15, K16, K17, K18, K19, K1A, K1B, K1C, K1D,      K1E,   K54, K55, K56,   K50, K51, K52, K5A, \
-    K20, K21, K22, K23, K24, K25, K26, K27, K28, K29, K2A, K2B, K2C, K2D,      K2E,   K64, K65, K66,   K60, K61, K62, K6B, \
-    K30, K32, K33, K34, K35, K36, K37, K38, K39, K3A, K3B, K3C, K3D,           K3E,   K74, K75, K76,   K70, K71, K72, K7B, \
-    K31, K47, K3F,                 K40,               K4F, K48,                K2F,   K77, K67, K57,   K73, K63, K53, K4E  \
-) { \
-    { KC_##K00, KC_##K01, KC_##K02, KC_##K03, KC_##K04, KC_##K05, KC_##K06, KC_##K07 }, \
-    { KC_##K08, KC_##K09, KC_##K0A, KC_##K0B, KC_##K0C, KC_##K0D, KC_##K0E, KC_##K0F }, \
-    { KC_##K10, KC_##K11, KC_##K12, KC_##K13, KC_##K14, KC_##K15, KC_##K16, KC_##K17 }, \
-    { KC_##K18, KC_##K19, KC_##K1A, KC_##K1B, KC_##K1C, KC_##K1D, KC_##K1E, KC_NO,   }, \
-    { KC_##K20, KC_##K21, KC_##K22, KC_##K23, KC_##K24, KC_##K25, KC_##K26, KC_##K27 }, \
-    { KC_##K28, KC_##K29, KC_##K2A, KC_##K2B, KC_##K2C, KC_##K2D, KC_##K2E, KC_##K2F }, \
-    { KC_##K30, KC_##K31, KC_##K32, KC_##K33, KC_##K34, KC_##K35, KC_##K36, KC_##K37 }, \
-    { KC_##K38, KC_##K39, KC_##K3A, KC_##K3B, KC_##K3C, KC_##K3D, KC_##K3E, KC_##K3F }, \
-    { KC_##K40, KC_##K41, KC_##K42, KC_##K43, KC_##K44, KC_##K45, KC_##K46, KC_##K47 }, \
-    { KC_##K48, KC_NO,    KC_##K4A, KC_NO,    KC_NO,    KC_NO,    KC_##K4E, KC_##K4F }, \
-    { KC_##K50, KC_##K51, KC_##K52, KC_##K53, KC_##K54, KC_##K55, KC_##K56, KC_##K57 }, \
-    { KC_NO,    KC_NO,    KC_##K5A, KC_NO,    KC_NO,    KC_NO,    KC_NO,    KC_NO,   }, \
-    { KC_##K60, KC_##K61, KC_##K62, KC_##K63, KC_##K64, KC_##K65, KC_##K66, KC_##K67 }, \
-    { KC_NO,    KC_NO,    KC_NO,    KC_##K6B, KC_NO,    KC_NO,    KC_NO,    KC_NO,   }, \
-    { KC_##K70, KC_##K71, KC_##K72, KC_##K73, KC_##K74, KC_##K75, KC_##K76, KC_##K77 }, \
-    { KC_NO,    KC_NO,    KC_NO,    KC_##K7B, KC_NO,    KC_NO,    KC_NO,    KC_NO,   }  \
-}
-
-
-#endif
diff --git a/converter/ibm4704_usb/keymap_hasu.c b/converter/ibm4704_usb/keymap_hasu.c
deleted file mode 100644
index 14c171179c..0000000000
--- a/converter/ibm4704_usb/keymap_hasu.c
+++ /dev/null
@@ -1,85 +0,0 @@
-#include "keymap_common.h"
-
-
-const uint8_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = {
-    /* 0: default
-     * ,-----------------------------------------------------------.
-     * |  `|  1|  2|  3|  4|  5|  6|  7|  8|  9|  0|  -|  =|???|BS |
-     * |-----------------------------------------------------------|
-     * |Tab  |  Q|  W|  E|  R|  T|  Y|  U|  I|  O|  P|  [|  ]|    \|
-     * |-----------------------------------------------------------|
-     * |Ctrl  |  A|  S|  D|  F|  G|  H|  J|  K|  L|  ;|  '|xxx|Ret |
-     * |-----------------------------------------------------------|
-     * |Shif|xxx|  Z|  X|  C|  V|  B|  N|  M|  ,|  ,|  /|xxx|Shift |
-     * |-----------------------------------------------------------|
-     * |Ctrl |Gui|Alt  |         Space             |Alt  |Gui|Ctrl |
-     * `-----------------------------------------------------------'
-     */
-    KEYMAP_62(
-    ESC, 1,   2,   3,   4,   5,   6,   7,   8,   9,   0,   MINS,EQL, BSLS,GRV, \
-    TAB, Q,   W,   E,   R,   T,   Y,   U,   I,   O,   P,   LBRC,RBRC,BSPC, \
-    LCTL,A,   S,   D,   F,   G,   H,   J,   K,   L,   FN1, QUOT,NO,  ENT, \
-    LSFT,NO,  Z,   X,   C,   V,   B,   N,   M,   COMM,DOT, FN2, NO,  FN0, \
-    LCTL,LGUI,LALT,          FN3,                               RGUI,RCTL \
-    ),
-
-    KEYMAP_62(
-    ESC, F1,  F2,  F3,  F4,  F5,  F6,  F7,  F8,  F9,  F10, F11, F12, INS, DEL, \
-    CAPS,NO,  NO,  NO,  NO,  NO,  NO,  NO,  PSCR,SLCK,PAUS, UP, NO,  BSPC, \
-    LCTL,VOLD,VOLU,MUTE,NO,  NO,  PAST,PSLS,HOME,PGUP,LEFT,RGHT,NO,  ENT, \
-    LSFT,NO,  NO,  NO,  NO,  NO,  NO,  PPLS,PMNS,END, PGDN,DOWN,NO,  TRNS, \
-    LCTL,LGUI,LALT,          SPC,                               RGUI,RCTL \
-    ),
-
-    KEYMAP_62(
-    ESC, F1,  F2,  F3,  F4,  F5,  F6,  F7,  F8,  F9,  F10, F11, F12, INS, DEL, \
-    TAB, NO,  NO,  NO,  NO,  NO,  WH_L,WH_D,WH_U,WH_R,WSTP,WBAK,WFWD,BSPC, \
-    LCTL,NO,  ACL0,ACL1,ACL2,NO,  MS_L,MS_D,MS_U,MS_R,TRNS,NO,  NO,  ENT, \
-    LSFT,NO,  NO,  NO,  NO,  NO,  BTN3,BTN2,BTN1,BTN4,BTN5,NO,  NO,  RSFT,\
-    LCTL,LGUI,LALT,          BTN1,                              RGUI,RCTL \
-    ),
-
-    KEYMAP_62(
-    ESC, F1,  F2,  F3,  F4,  F5,  F6,  F7,  F8,  F9,  F10, F11, F12, INS, DEL, \
-    TAB, HOME,PGDN,UP,  PGUP,END, HOME,PGDN,PGUP,END, NO,  NO,  NO,  BSPC, \
-    LCTL,NO,  LEFT,DOWN,RGHT,NO,  LEFT,DOWN,UP,  RGHT,NO,  NO,  NO,  ENT, \
-    LSFT,NO,  NO,  NO,  NO,  NO,  NO,  HOME,PGDN,PGUP,END, TRNS,NO,  RSFT, \
-    LCTL,LGUI,LALT,          SPC,                               RGUI,RCTL \
-    ),
-
-    KEYMAP_62(
-    ESC, F1,  F2,  F3,  F4,  F5,  F6,  F7,  F8,  F9,  F10, F11, F12, INS, DEL, \
-    TAB, NO,  NO,  NO,  NO,  NO,  WH_L,WH_D,MS_U,WH_U,WH_R,BTN4,BTN5,FN4, \
-    LCTL,VOLD,VOLU,MUTE,NO,  NO,  BTN2,MS_L,MS_D,MS_R,BTN1,NO,  NO,  ENT, \
-    LSFT,NO,  NO,  NO,  NO,  NO,  BTN3,BTN2,BTN1,BTN4,BTN5,NO,  NO,  NO, \
-    LCTL,LGUI,LALT,          TRNS,                              RGUI,RCTL \
-    ),
-};
-
-enum macro_id {
-    ALT_TAB,
-};
-
-const uint16_t PROGMEM fn_actions[] = {
-    [0] = ACTION_LAYER_MOMENTARY(1),
-    [1] = ACTION_LAYER_TAP_KEY(2, KC_SCLN),
-    [2] = ACTION_LAYER_TAP_KEY(3, KC_SLASH),
-    [3] = ACTION_LAYER_TAP_KEY(4, KC_SPC),
-    [4] = ACTION_MACRO(ALT_TAB),
-};
-
-/*
- * Macro definition
- */
-const macro_t *action_get_macro(keyrecord_t *record, uint8_t id, uint8_t opt)
-{
-    keyevent_t event = record->event;
-
-    switch (id) {
-        case ALT_TAB:
-            return (event.pressed ?
-                    MACRO( D(LALT), D(TAB), END ) :
-                    MACRO( U(TAB), END ));
-    }
-    return MACRO_NONE;
-}
diff --git a/converter/ibm4704_usb/keymap_plain.c b/converter/ibm4704_usb/keymap_plain.c
deleted file mode 100644
index 4aed684e4c..0000000000
--- a/converter/ibm4704_usb/keymap_plain.c
+++ /dev/null
@@ -1,50 +0,0 @@
-#include "keymap_common.h"
-
-
-const uint8_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = {
-    /* 0: default
-     * ,-----------------------------------------------------------.
-     * |  `|  1|  2|  3|  4|  5|  6|  7|  8|  9|  0|  -|  =|???|BS |
-     * |-----------------------------------------------------------|
-     * |Tab  |  Q|  W|  E|  R|  T|  Y|  U|  I|  O|  P|  [|  ]|    \|
-     * |-----------------------------------------------------------|
-     * |Ctrl  |  A|  S|  D|  F|  G|  H|  J|  K|  L|  ;|  '|Ret|Ret |
-     * |-----------------------------------------------------------|
-     * |Shif|Shf|  Z|  X|  C|  V|  B|  N|  M|  ,|  ,|  /|???|Shift |
-     * |-----------------------------------------------------------|
-     * |Ctrl |Gui|Alt  |         Space             |Alt* |Gui|Fn   |
-     * `------------------