[Keyboard] wilba.tech PCB refactoring (#6982)

* Cleanup

* Refactor VIA rules.mk

* WT mono backlight refactor, VIA support

* Added WT75-C

* Fixed compile error

* Cleanup rules.mk

* Review changes

* Review changes

48 files changed, 1132 insertions, 1250 deletions

diff --git a/keyboards/aeboards/aegis/config.h b/keyboards/aeboards/aegis/config.h
index d8c256c7d9..2a35897300 100644
--- a/keyboards/aeboards/aegis/config.h
+++ b/keyboards/aeboards/aegis/config.h
@@ -47,8 +47,6 @@
 /* Locking resynchronize hack */
 #define LOCKING_RESYNC_ENABLE
 
-//#define WT_MONO_BACKLIGHT
-
 #define DYNAMIC_KEYMAP_LAYER_COUNT 4
 
 // EEPROM usage
diff --git a/keyboards/aeboards/ext65/config.h b/keyboards/aeboards/ext65/config.h
index b3e1b8c2f0..7255b463fc 100644
--- a/keyboards/aeboards/ext65/config.h
+++ b/keyboards/aeboards/ext65/config.h
@@ -47,8 +47,6 @@
 /* Locking resynchronize hack */
 #define LOCKING_RESYNC_ENABLE
 
-//#define WT_MONO_BACKLIGHT
-
 #define DYNAMIC_KEYMAP_LAYER_COUNT 4
 
 // EEPROM usage
diff --git a/keyboards/snagpad/config.h b/keyboards/snagpad/config.h
index cd32a3d8c2..a4ab9d5e26 100644
--- a/keyboards/snagpad/config.h
+++ b/keyboards/snagpad/config.h
@@ -48,9 +48,6 @@
 #define RGBLIGHT_VAL_STEP 8
 #endif
 
-// Does not use WT_MONO_BACKLIGHT
-// #define WT_MONO_BACKLIGHT
-
 #define DYNAMIC_KEYMAP_LAYER_COUNT 4
 
 // EEPROM usage
diff --git a/keyboards/wilba_tech/rama_works_koyu/rules.mk b/keyboards/wilba_tech/rama_works_koyu/rules.mk
index 9839602247..ebcb6a455f 100644
--- a/keyboards/wilba_tech/rama_works_koyu/rules.mk
+++ b/keyboards/wilba_tech/rama_works_koyu/rules.mk
@@ -1,5 +1,3 @@
-
-
 # project specific files
 SRC =	keyboards/wilba_tech/wt_main.c \
 		keyboards/wilba_tech/wt_rgb_backlight.c \
@@ -10,42 +8,14 @@ SRC =	keyboards/wilba_tech/wt_main.c \
 # MCU name
 MCU = atmega32u4
 
-# Processor frequency.
-#     This will define a symbol, F_CPU, in all source code files equal to the
-#     processor frequency in Hz. You can then use this symbol in your source code to
-#     calculate timings. Do NOT tack on a 'UL' at the end, this will be done
-#     automatically to create a 32-bit value in your source code.
-#
-#     This will be an integer division of F_USB below, as it is sourced by
-#     F_USB after it has run through any CPU prescalers. Note that this value
-#     does not *change* the processor frequency - it should merely be updated to
-#     reflect the processor speed set externally so that the code can use accurate
-#     software delays.
-F_CPU = 16000000
-
-#
-# LUFA specific
-#
-# Target architecture (see library "Board Types" documentation).
-ARCH = AVR8
-
-# Input clock frequency.
-#     This will define a symbol, F_USB, in all source code files equal to the
-#     input clock frequency (before any prescaling is performed) in Hz. This value may
-#     differ from F_CPU if prescaling is used on the latter, and is required as the
-#     raw input clock is fed directly to the PLL sections of the AVR for high speed
-#     clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
-#     at the end, this will be done automatically to create a 32-bit value in your
-#     source code.
-#
-#     If no clock division is performed on the input clock inside the AVR (via the
-#     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
-F_USB = $(F_CPU)
-
-# Interrupt driven control endpoint task(+60)
-OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
-
-# Boot Section
+# Bootloader selection
+#   Teensy       halfkay
+#   Pro Micro    caterina
+#   Atmel DFU    atmel-dfu
+#   LUFA DFU     lufa-dfu
+#   QMK DFU      qmk-dfu
+#   ATmega32A    bootloadHID
+#   ATmega328P   USBasp
 BOOTLOADER = atmel-dfu
 
 # Do not put the microcontroller into power saving mode
diff --git a/keyboards/wilba_tech/rama_works_m10_b/config.h b/keyboards/wilba_tech/rama_works_m10_b/config.h
index 6901309a08..f72ecae85c 100644
--- a/keyboards/wilba_tech/rama_works_m10_b/config.h
+++ b/keyboards/wilba_tech/rama_works_m10_b/config.h
@@ -181,8 +181,6 @@ along with this program.  If not, see <http://www.gnu.org/licenses/>.
 /* override number of MIDI tone keycodes (each octave adds 12 keycodes and allocates 12 bytes) */
 //#define MIDI_TONE_KEYCODE_OCTAVES 1
 
-//#define WT_MONO_BACKLIGHT
-
 #define DYNAMIC_KEYMAP_LAYER_COUNT 4
 
 // EEPROM usage
diff --git a/keyboards/wilba_tech/rama_works_m10_b/rules.mk b/keyboards/wilba_tech/rama_works_m10_b/rules.mk
index 70258b9ead..99330021f2 100644
--- a/keyboards/wilba_tech/rama_works_m10_b/rules.mk
+++ b/keyboards/wilba_tech/rama_works_m10_b/rules.mk
@@ -4,44 +4,14 @@ SRC =	keyboards/wilba_tech/wt_main.c
 # MCU name
 MCU = atmega32u4
 
-# Processor frequency.
-#     This will define a symbol, F_CPU, in all source code files equal to the
-#     processor frequency in Hz. You can then use this symbol in your source code to
-#     calculate timings. Do NOT tack on a 'UL' at the end, this will be done
-#     automatically to create a 32-bit value in your source code.
-#
-#     This will be an integer division of F_USB below, as it is sourced by
-#     F_USB after it has run through any CPU prescalers. Note that this value
-#     does not *change* the processor frequency - it should merely be updated to
-#     reflect the processor speed set externally so that the code can use accurate
-#     software delays.
-F_CPU = 16000000
-
-
-#
-# LUFA specific
-#
-# Target architecture (see library "Board Types" documentation).
-ARCH = AVR8
-
-# Input clock frequency.
-#     This will define a symbol, F_USB, in all source code files equal to the
-#     input clock frequency (before any prescaling is performed) in Hz. This value may
-#     differ from F_CPU if prescaling is used on the latter, and is required as the
-#     raw input clock is fed directly to the PLL sections of the AVR for high speed
-#     clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
-#     at the end, this will be done automatically to create a 32-bit value in your
-#     source code.
-#
-#     If no clock division is performed on the input clock inside the AVR (via the
-#     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
-F_USB = $(F_CPU)
-
-# Interrupt driven control endpoint task(+60)
-OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
-
-
-# Boot Section
+# Bootloader selection
+#   Teensy       halfkay
+#   Pro Micro    caterina
+#   Atmel DFU    atmel-dfu
+#   LUFA DFU     lufa-dfu
+#   QMK DFU      qmk-dfu
+#   ATmega32A    bootloadHID
+#   ATmega328P   USBasp
 BOOTLOADER = atmel-dfu
 
 
diff --git a/keyboards/wilba_tech/rama_works_m60_a/rules.mk b/keyboards/wilba_tech/rama_works_m60_a/rules.mk
index 3b2287333c..4ce5dc54cb 100644
--- a/keyboards/wilba_tech/rama_works_m60_a/rules.mk
+++ b/keyboards/wilba_tech/rama_works_m60_a/rules.mk
@@ -10,42 +10,14 @@ SRC =	keyboards/wilba_tech/wt_main.c \
 # MCU name
 MCU = atmega32u4
 
-# Processor frequency.
-#     This will define a symbol, F_CPU, in all source code files equal to the
-#     processor frequency in Hz. You can then use this symbol in your source code to
-#     calculate timings. Do NOT tack on a 'UL' at the end, this will be done
-#     automatically to create a 32-bit value in your source code.
-#
-#     This will be an integer division of F_USB below, as it is sourced by
-#     F_USB after it has run through any CPU prescalers. Note that this value
-#     does not *change* the processor frequency - it should merely be updated to
-#     reflect the processor speed set externally so that the code can use accurate
-#     software delays.
-F_CPU = 16000000
-
-#
-# LUFA specific
-#
-# Target architecture (see library "Board Types" documentation).
-ARCH = AVR8
-
-# Input clock frequency.
-#     This will define a symbol, F_USB, in all source code files equal to the
-#     input clock frequency (before any prescaling is performed) in Hz. This value may
-#     differ from F_CPU if prescaling is used on the latter, and is required as the
-#     raw input clock is fed directly to the PLL sections of the AVR for high speed
-#     clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
-#     at the end, this will be done automatically to create a 32-bit value in your
-#     source code.
-#
-#     If no clock division is performed on the input clock inside the AVR (via the
-#     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
-F_USB = $(F_CPU)
-
-# Interrupt driven control endpoint task(+60)
-OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
-
-# Boot Section
+# Bootloader selection
+#   Teensy       halfkay
+#   Pro Micro    caterina
+#   Atmel DFU    atmel-dfu
+#   LUFA DFU     lufa-dfu
+#   QMK DFU      qmk-dfu
+#   ATmega32A    bootloadHID
+#   ATmega328P   USBasp
 BOOTLOADER = atmel-dfu
 
 # Do not put the microcontroller into power saving mode
diff --git a/keyboards/wilba_tech/rama_works_m6_a/rules.mk b/keyboards/wilba_tech/rama_works_m6_a/rules.mk
index 4270e7090c..32f0e25de8 100644
--- a/keyboards/wilba_tech/rama_works_m6_a/rules.mk
+++ b/keyboards/wilba_tech/rama_works_m6_a/rules.mk
@@ -4,43 +4,14 @@ SRC =	keyboards/wilba_tech/wt_main.c
 # MCU name
 MCU = atmega32u4
 
-# Processor frequency.
-#     This will define a symbol, F_CPU, in all source code files equal to the
-#     processor frequency in Hz. You can then use this symbol in your source code to
-#     calculate timings. Do NOT tack on a 'UL' at the end, this will be done
-#     automatically to create a 32-bit value in your source code.
-#
-#     This will be an integer division of F_USB below, as it is sourced by
-#     F_USB after it has run through any CPU prescalers. Note that this value
-#     does not *change* the processor frequency - it should merely be updated to
-#     reflect the processor speed set externally so that the code can use accurate
-#     software delays.
-F_CPU = 16000000
-
-
-#
-# LUFA specific
-#
-# Target architecture (see library "Board Types" documentation).
-ARCH = AVR8
-
-# Input clock frequency.
-#     This will define a symbol, F_USB, in all source code files equal to the
-#     input clock frequency (before any prescaling is performed) in Hz. This value may
-#     differ from F_CPU if prescaling is used on the latter, and is required as the
-#     raw input clock is fed directly to the PLL sections of the AVR for high speed
-#     clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
-#     at the end, this will be done automatically to create a 32-bit value in your
-#     source code.
-#
-#     If no clock division is performed on the input clock inside the AVR (via the
-#     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
-F_USB = $(F_CPU)
-
-# Interrupt driven control endpoint task(+60)
-OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
-
-# Boot Section
+# Bootloader selection
+#   Teensy       halfkay
+#   Pro Micro    caterina
+#   Atmel DFU    atmel-dfu
+#   LUFA DFU     lufa-dfu
+#   QMK DFU      qmk-dfu
+#   ATmega32A    bootloadHID
+#   ATmega328P   USBasp
 BOOTLOADER = atmel-dfu
 
 # Do not put the microcontroller into power saving mode
diff --git a/keyboards/wilba_tech/rama_works_m6_b/rules.mk b/keyboards/wilba_tech/rama_works_m6_b/rules.mk
index 6b7b3a63d8..c016fa344f 100644
--- a/keyboards/wilba_tech/rama_works_m6_b/rules.mk
+++ b/keyboards/wilba_tech/rama_works_m6_b/rules.mk
@@ -5,47 +5,17 @@ SRC =	keyboards/wilba_tech/wt_main.c \
 		drivers/issi/is31fl3218.c \
 		drivers/avr/i2c_master.c
 
-
 # MCU name
 MCU = atmega32u4
 
-# Processor frequency.
-#     This will define a symbol, F_CPU, in all source code files equal to the
-#     processor frequency in Hz. You can then use this symbol in your source code to
-#     calculate timings. Do NOT tack on a 'UL' at the end, this will be done
-#     automatically to create a 32-bit value in your source code.
-#
-#     This will be an integer division of F_USB below, as it is sourced by
-#     F_USB after it has run through any CPU prescalers. Note that this value
-#     does not *change* the processor frequency - it should merely be updated to
-#     reflect the processor speed set externally so that the code can use accurate
-#     software delays.
-F_CPU = 16000000
-
-
-#
-# LUFA specific
-#
-# Target architecture (see library "Board Types" documentation).
-ARCH = AVR8
-
-# Input clock frequency.
-#     This will define a symbol, F_USB, in all source code files equal to the
-#     input clock frequency (before any prescaling is performed) in Hz. This value may
-#     differ from F_CPU if prescaling is used on the latter, and is required as the
-#     raw input clock is fed directly to the PLL sections of the AVR for high speed
-#     clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
-#     at the end, this will be done automatically to create a 32-bit value in your
-#     source code.
-#
-#     If no clock division is performed on the input clock inside the AVR (via the
-#     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
-F_USB = $(F_CPU)
-
-# Interrupt driven control endpoint task(+60)
-OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
-
-# Boot Section
+# Bootloader selection
+#   Teensy       halfkay
+#   Pro Micro    caterina
+#   Atmel DFU    atmel-dfu
+#   LUFA DFU     lufa-dfu
+#   QMK DFU      qmk-dfu
+#   ATmega32A    bootloadHID
+#   ATmega328P   USBasp
 BOOTLOADER = atmel-dfu
 
 # Do not put the microcontroller into power saving mode
diff --git a/keyboards/wilba_tech/rama_works_u80_a/config.h b/keyboards/wilba_tech/rama_works_u80_a/config.h
index 348b124b90..d0bf0ed1e3 100644
--- a/keyboards/wilba_tech/rama_works_u80_a/config.h
+++ b/keyboards/wilba_tech/rama_works_u80_a/config.h
@@ -179,8 +179,6 @@
 /* override number of MIDI tone keycodes (each octave adds 12 keycodes and allocates 12 bytes) */
 //#define MIDI_TONE_KEYCODE_OCTAVES 1
 
-//#define WT_MONO_BACKLIGHT
-
 // IS31FL3731 driver
 #define DRIVER_COUNT 3
 #define DRIVER_LED_TOTAL 108
diff --git a/keyboards/wilba_tech/rama_works_u80_a/rules.mk b/keyboards/wilba_tech/rama_works_u80_a/rules.mk
index 6079ad8932..caecaecbb7 100644
--- a/keyboards/wilba_tech/rama_works_u80_a/rules.mk
+++ b/keyboards/wilba_tech/rama_works_u80_a/rules.mk
@@ -8,44 +8,14 @@ SRC =	keyboards/wilba_tech/wt_main.c \
 # MCU name
 MCU = atmega32u4
 
-# Processor frequency.
-#     This will define a symbol, F_CPU, in all source code files equal to the
-#     processor frequency in Hz. You can then use this symbol in your source code to
-#     calculate timings. Do NOT tack on a 'UL' at the end, this will be done
-#     automatically to create a 32-bit value in your source code.
-#
-#     This will be an integer division of F_USB below, as it is sourced by
-#     F_USB after it has run through any CPU prescalers. Note that this value
-#     does not *change* the processor frequency - it should merely be updated to
-#     reflect the processor speed set externally so that the code can use accurate
-#     software delays.
-F_CPU = 16000000
-
-
-#
-# LUFA specific
-#
-# Target architecture (see library "Board Types" documentation).
-ARCH = AVR8
-
-# Input clock frequency.
-#     This will define a symbol, F_USB, in all source code files equal to the
-#     input clock frequency (before any prescaling is performed) in Hz. This value may
-#     differ from F_CPU if prescaling is used on the latter, and is required as the
-#     raw input clock is fed directly to the PLL sections of the AVR for high speed
-#     clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
-#     at the end, this will be done automatically to create a 32-bit value in your
-#     source code.
-#
-#     If no clock division is performed on the input clock inside the AVR (via the
-#     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
-F_USB = $(F_CPU)
-
-# Interrupt driven control endpoint task(+60)
-OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
-
-
-# Boot Section
+# Bootloader selection
+#   Teensy       halfkay
+#   Pro Micro    caterina
+#   Atmel DFU    atmel-dfu
+#   LUFA DFU     lufa-dfu
+#   QMK DFU      qmk-dfu
+#   ATmega32A    bootloadHID
+#   ATmega328P   USBasp
 BOOTLOADER = atmel-dfu
 
 
diff --git a/keyboards/wilba_tech/wt60_a/config.h b/keyboards/wilba_tech/wt60_a/config.h
index 3ac8ea6fc0..6e1e0e81cc 100644
--- a/keyboards/wilba_tech/wt60_a/config.h
+++ b/keyboards/wilba_tech/wt60_a/config.h
@@ -179,14 +179,33 @@
 /* override number of MIDI tone keycodes (each octave adds 12 keycodes and allocates 12 bytes) */
 //#define MIDI_TONE_KEYCODE_OCTAVES 1
 
-#define WT_MONO_BACKLIGHT
+// enable the mono backlight
+#define MONO_BACKLIGHT_ENABLED 1
+
+// enable the RGB indicator for WT75-A
+#define MONO_BACKLIGHT_WT75_A
+
+// disable backlight when USB suspended (PC sleep/hibernate/shutdown)
+#define MONO_BACKLIGHT_DISABLE_WHEN_USB_SUSPENDED 0
+
+// disable backlight after timeout in minutes, 0 = no timeout
+#define MONO_BACKLIGHT_DISABLE_AFTER_TIMEOUT 0
+
+// the default brightness
+#define MONO_BACKLIGHT_BRIGHTNESS 255
+
+// the default effect
+#define MONO_BACKLIGHT_EFFECT 1
+
+// the default effect speed (0-3)
+#define MONO_BACKLIGHT_EFFECT_SPEED 0
 
 #define DYNAMIC_KEYMAP_LAYER_COUNT 4
 
 // EEPROM usage
 
 // TODO: refactor with new user EEPROM code (coming soon)
-#define EEPROM_MAGIC 0x451F
+#define EEPROM_MAGIC 0x4520
 #define EEPROM_MAGIC_ADDR 34
 // Bump this every time we change what we store
 // This will automatically reset the EEPROM with defaults
@@ -194,9 +213,11 @@
 #define EEPROM_VERSION 0x08
 #define EEPROM_VERSION_ADDR 36
 
-// Dynamic keymap starts after EEPROM version
-#define DYNAMIC_KEYMAP_EEPROM_ADDR 37
-// Dynamic macro starts after dynamic keymaps (37+(4*5*14*2)) = (37+560)
-#define DYNAMIC_KEYMAP_MACRO_EEPROM_ADDR 597
-#define DYNAMIC_KEYMAP_MACRO_EEPROM_SIZE 427
+// Backlight config starts after EEPROM version
+#define MONO_BACKLIGHT_CONFIG_EEPROM_ADDR 37
+// Dynamic keymap starts after backlight config (37+7)
+#define DYNAMIC_KEYMAP_EEPROM_ADDR 44
+// Dynamic macro starts after dynamic keymaps (44+(4*5*14*2)) = (44+560)
+#define DYNAMIC_KEYMAP_MACRO_EEPROM_ADDR 604
+#define DYNAMIC_KEYMAP_MACRO_EEPROM_SIZE 420
 #define DYNAMIC_KEYMAP_MACRO_COUNT 16
diff --git a/keyboards/wilba_tech/wt60_a/keymaps/via/rules.mk b/keyboards/wilba_tech/wt60_a/keymaps/via/rules.mk
index 76a07d7a44..8834bf0c8e 100644
--- a/keyboards/wilba_tech/wt60_a/keymaps/via/rules.mk
+++ b/keyboards/wilba_tech/wt60_a/keymaps/via/rules.mk
@@ -1,71 +1,2 @@
-# project specific files
-SRC =	drivers/issi/is31fl3736.c \
-		drivers/avr/i2c_master.c \
-		keyboards/wilba_tech/wt_mono_backlight.c \
-		keyboards/wilba_tech/wt_main.c
-		
-# MCU name
-MCU = atmega32u4
-
-# Processor frequency.
-#     This will define a symbol, F_CPU, in all source code files equal to the
-#     processor frequency in Hz. You can then use this symbol in your source code to
-#     calculate timings. Do NOT tack on a 'UL' at the end, this will be done
-#     automatically to create a 32-bit value in your source code.
-#
-#     This will be an integer division of F_USB below, as it is sourced by
-#     F_USB after it has run through any CPU prescalers. Note that this value
-#     does not *change* the processor frequency - it should merely be updated to
-#     reflect the processor speed set externally so that the code can use accurate
-#     software delays.
-F_CPU = 16000000
-
-
-#
-# LUFA specific
-#
-# Target architecture (see library "Board Types" documentation).
-ARCH = AVR8
-
-# Input clock frequency.
-#     This will define a symbol, F_USB, in all source code files equal to the
-#     input clock frequency (before any prescaling is performed) in Hz. This value may
-#     differ from F_CPU if prescaling is used on the latter, and is required as the
-#     raw input clock is fed directly to the PLL sections of the AVR for high speed
-#     clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
-#     at the end, this will be done automatically to create a 32-bit value in your
-#     source code.
-#
-#     If no clock division is performed on the input clock inside the AVR (via the
-#     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
-F_USB = $(F_CPU)
-
-# Interrupt driven control endpoint task(+60)
-OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
-
-
-# Boot Section
-BOOTLOADER = atmel-dfu
-
-
-# Build Options
-#   change yes to no to disable
-#
-BOOTMAGIC_ENABLE = no      # Virtual DIP switch configuration(+1000)
-MOUSEKEY_ENABLE = no       # Mouse keys(+4700)
-EXTRAKEY_ENABLE = yes       # Audio control and System control(+450)
-CONSOLE_ENABLE = no        # Console for debug(+400)
-COMMAND_ENABLE = no        # Commands for debug and configuration
-# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE
-SLEEP_LED_ENABLE = no       # Breathing sleep LED during USB suspend
-# if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
-NKRO_ENABLE = yes            # USB Nkey Rollover
-BACKLIGHT_ENABLE = no       # Enable keyboard backlight functionality on B7 by default
-MIDI_ENABLE = no            # MIDI support (+2400 to 4200, depending on config)
-UNICODE_ENABLE = no         # Unicode
-BLUETOOTH_ENABLE = no       # Enable Bluetooth with the Adafruit EZ-Key HID
-AUDIO_ENABLE = no           # Audio output on port C6
-FAUXCLICKY_ENABLE = no      # Use buzzer to emulate clicky switches
-
 RAW_ENABLE = yes
 DYNAMIC_KEYMAP_ENABLE = yes
\ No newline at end of file
diff --git a/keyboards/wilba_tech/wt60_a/rules.mk b/keyboards/wilba_tech/wt60_a/rules.mk
index e41f2186b3..4f702fab49 100644
--- a/keyboards/wilba_tech/wt60_a/rules.mk
+++ b/keyboards/wilba_tech/wt60_a/rules.mk
@@ -1,6 +1,7 @@
 # project specific files
 SRC =	drivers/issi/is31fl3736.c \
 		drivers/avr/i2c_master.c \
+		quantum/color.c \
 		keyboards/wilba_tech/wt_mono_backlight.c \
 		keyboards/wilba_tech/wt_main.c
 		
diff --git a/keyboards/wilba_tech/wt60_d/keymaps/via/rules.mk b/keyboards/wilba_tech/wt60_d/keymaps/via/rules.mk
index f072c67198..8834bf0c8e 100644
--- a/keyboards/wilba_tech/wt60_d/keymaps/via/rules.mk
+++ b/keyboards/wilba_tech/wt60_d/keymaps/via/rules.mk
@@ -1,68 +1,2 @@
-# project specific files
-SRC =	keyboards/wilba_tech/wt_main.c
-		
-# MCU name
-MCU = atmega32u4
-
-# Processor frequency.
-#     This will define a symbol, F_CPU, in all source code files equal to the
-#     processor frequency in Hz. You can then use this symbol in your source code to
-#     calculate timings. Do NOT tack on a 'UL' at the end, this will be done
-#     automatically to create a 32-bit value in your source code.
-#
-#     This will be an integer division of F_USB below, as it is sourced by
-#     F_USB after it has run through any CPU prescalers. Note that this value
-#     does not *change* the processor frequency - it should merely be updated to
-#     reflect the processor speed set externally so that the code can use accurate
-#     software delays.
-F_CPU = 16000000
-
-
-#
-# LUFA specific
-#
-# Target architecture (see library "Board Types" documentation).
-ARCH = AVR8
-
-# Input clock frequency.