1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
|
/**
* Copyright 2021 Charly Delay <charly@codesink.dev> (@0xcharly)
*
* This program is free software: you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation, either version 2 of the License, or
* (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program. If not, see <http://www.gnu.org/licenses/>.
*/
#pragma once
#undef MATRIX_COL_PINS
#define MATRIX_COL_PINS \
{ B0, B1, B10, B3, B4, B5 }
#undef MATRIX_COL_PINS_RIGHT
#define MATRIX_COL_PINS_RIGHT \
{ B0, B1, B10, B3, B4, B5 }
#undef MATRIX_ROW_PINS
#define MATRIX_ROW_PINS \
{ B15, A2, B8, A8, B9 }
#undef MATRIX_ROW_PINS_RIGHT
#define MATRIX_ROW_PINS_RIGHT \
{ B15, A2, B8, A8, B9 }
#define DIODE_DIRECTION ROW2COL
#define SPLIT_HAND_PIN A3
#undef RGB_DI_PIN
#define RGB_DI_PIN A1
#define WS2812_EXTERNAL_PULLUP
#define WS2812_PWM_DRIVER PWMD2
#define WS2812_PWM_CHANNEL 2
#define WS2812_PWM_PAL_MODE 1
#define WS2812_EXTERNAL_PULLUP
#define WS2812_DMA_STREAM STM32_DMA1_STREAM1
#define WS2812_DMA_CHANNEL 3
#define WS2812_PWM_TARGET_PERIOD 800000
#define DEBUG_LED_PIN C13
#undef SOFT_SERIAL_PIN
// #define SERIAL_USART_FULL_DUPLEX // Enable full duplex operation mode.
#define SERIAL_USART_TX_PIN A9
// #define SERIAL_USART_RX_PIN A3
// #define SERIAL_USART_DRIVER SD2
// #define SERIAL_USART_TX_PAL_MODE 7 // Pin "alternate function", see the respective datasheet for the appropriate values for your MCU. default: 7
// #define SERIAL_USART_RX_PAL_MODE 7 // Pin "alternate function", see the respective datasheet for the appropriate values for your MCU. default: 7
// #define SERIAL_USART_TIMEOUT 100 // USART driver timeout. default 100
// // #define SERIAL_USART_PIN_SWAP // swap RX and TX pins on master
// // To use the highest possible baudrate (3.75Mbit/s) uncomment the following
// // line, this can result in dropped communications so lower the speed if there
// // are many timeouts.
// // #define SERIAL_USART_SPEED (STM32_PCLK2 >> 4)
#define SERIAL_USART_SPEED 921600
#define CRC8_USE_TABLE
#define CRC8_OPTIMIZE_SPEED
/* spi config for eeprom and pmw3360 sensor */
#define SPI_DRIVER SPID1
#define SPI_SCK_PIN A5
#define SPI_SCK_PAL_MODE 5
#define SPI_MOSI_PIN A7
#define SPI_MOSI_PAL_MODE 5
#define SPI_MISO_PIN A6
#define SPI_MISO_PAL_MODE 5
#define EXTERNAL_EEPROM_SPI_SLAVE_SELECT_PIN A4
#define EXTERNAL_EEPROM_SPI_CLOCK_DIVISOR 64
#undef PMW3360_CS_PIN
#define PMW3360_CS_PIN B14
#define PMW3360_CS_MODE 3
#define PMW3360_CS_DIVISOR 64
#define CHARYBDIS_MINIMUM_DEFAULT_DPI 1200
#define CHARYBDIS_DEFAULT_DPI_CONFIG_STEP 400
#define CHARYBDIS_MINIMUM_SNIPING_DPI 200
#define CHARYBDIS_SNIPING_DPI_CONFIG_STEP 100
/* RGB Matrix. */
#undef RGB_MATRIX_MAXIMUM_BRIGHTNESS
#define RGB_MATRIX_MAXIMUM_BRIGHTNESS 150
|
