1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
224
225
226
227
228
229
230
231
232
233
234
235
236
237
238
239
240
241
242
243
244
245
246
247
248
249
250
251
252
253
254
255
256
257
258
259
260
261
262
263
264
265
266
267
268
269
270
271
272
273
274
275
276
277
278
279
280
281
282
283
284
285
286
287
288
289
290
291
292
293
294
295
296
297
298
299
300
301
302
303
304
305
306
307
308
309
310
311
312
313
314
315
316
317
318
319
320
321
322
323
324
325
326
327
328
329
330
331
332
333
334
335
336
337
338
339
340
341
342
343
344
345
346
347
348
349
350
351
352
353
354
355
356
357
358
359
360
361
362
363
364
365
366
367
368
369
370
371
372
373
374
375
376
377
378
379
380
381
382
383
384
385
386
387
388
389
390
391
392
393
394
395
396
397
398
399
400
401
402
403
404
405
406
407
408
409
410
411
412
413
414
415
416
417
418
419
420
421
422
423
424
425
426
427
428
429
430
431
432
433
434
435
436
437
438
439
440
441
442
443
444
445
446
447
448
449
450
451
452
453
454
455
456
457
458
459
460
461
462
463
464
465
466
467
468
469
470
471
472
473
474
475
476
477
478
479
480
481
482
483
484
485
486
487
488
489
490
491
492
493
494
495
496
497
498
499
500
501
502
503
504
505
506
507
508
509
510
511
512
513
514
515
516
517
518
519
520
521
522
523
524
525
526
527
528
529
530
531
532
533
534
535
536
537
538
539
540
541
542
543
544
545
546
547
548
549
550
551
552
553
554
555
556
557
558
559
560
561
562
563
564
565
566
567
568
569
570
571
572
573
574
575
576
577
578
579
580
581
582
583
584
585
586
587
588
589
590
591
592
593
594
595
596
597
598
599
600
601
602
603
604
605
606
607
608
609
610
611
612
613
614
615
616
617
618
619
620
621
622
623
624
625
626
627
628
629
630
631
632
633
634
635
636
637
638
639
640
641
642
643
644
645
646
647
648
649
650
651
652
653
654
655
656
657
658
659
660
661
662
663
664
665
666
667
668
669
670
671
672
673
674
675
676
677
678
679
680
681
682
683
684
685
686
687
688
689
690
691
692
693
694
695
696
697
698
699
700
701
702
703
704
705
706
707
708
709
710
711
712
713
714
715
716
717
718
719
720
721
722
723
724
725
726
727
728
729
730
731
732
733
734
735
736
737
738
739
740
741
742
743
744
745
746
747
748
749
750
751
752
753
754
755
756
757
758
759
760
761
762
763
764
765
766
767
768
769
770
771
772
773
774
775
776
777
778
779
780
781
782
783
784
785
786
787
788
789
790
791
792
793
794
795
796
797
798
799
800
801
802
803
804
805
806
807
808
809
810
811
812
813
814
815
816
817
818
819
820
821
822
823
824
825
826
827
828
829
830
831
832
833
834
835
836
837
838
839
840
841
842
843
844
845
846
847
848
849
850
851
852
853
854
855
856
857
858
859
860
861
862
863
864
865
|
# RGB Matrix Lighting :id=rgb-matrix-lighting
This feature allows you to use RGB LED matrices driven by external drivers. It hooks into the RGBLIGHT system so you can use the same keycodes as RGBLIGHT to control it.
If you want to use single color LED's you should use the [LED Matrix Subsystem](feature_led_matrix.md) instead.
## Driver configuration :id=driver-configuration
---
### IS31FL3731 :id=is31fl3731
There is basic support for addressable RGB matrix lighting with the I2C IS31FL3731 RGB controller. To enable it, add this to your `rules.mk`:
```make
RGB_MATRIX_ENABLE = yes
RGB_MATRIX_DRIVER = IS31FL3731
```
You can use between 1 and 4 IS31FL3731 IC's. Do not specify `DRIVER_ADDR_<N>` defines for IC's that are not present on your keyboard. You can define the following items in `config.h`:
| Variable | Description | Default |
|----------|-------------|---------|
| `ISSI_TIMEOUT` | (Optional) How long to wait for i2c messages, in milliseconds | 100 |
| `ISSI_PERSISTENCE` | (Optional) Retry failed messages this many times | 0 |
| `ISSI_3731_DEGHOST` | (Optional) Set this define to enable de-ghosting by halving Vcc during blanking time | |
| `DRIVER_COUNT` | (Required) How many RGB driver IC's are present | |
| `DRIVER_LED_TOTAL` | (Required) How many RGB lights are present across all drivers | |
| `DRIVER_ADDR_1` | (Required) Address for the first RGB driver | |
| `DRIVER_ADDR_2` | (Optional) Address for the second RGB driver | |
| `DRIVER_ADDR_3` | (Optional) Address for the third RGB driver | |
| `DRIVER_ADDR_4` | (Optional) Address for the fourth RGB driver | |
Here is an example using 2 drivers.
```c
// This is a 7-bit address, that gets left-shifted and bit 0
// set to 0 for write, 1 for read (as per I2C protocol)
// The address will vary depending on your wiring:
// 0b1110100 AD <-> GND
// 0b1110111 AD <-> VCC
// 0b1110101 AD <-> SCL
// 0b1110110 AD <-> SDA
#define DRIVER_ADDR_1 0b1110100
#define DRIVER_ADDR_2 0b1110110
#define DRIVER_COUNT 2
#define DRIVER_1_LED_TOTAL 25
#define DRIVER_2_LED_TOTAL 24
#define DRIVER_LED_TOTAL (DRIVER_1_LED_TOTAL + DRIVER_2_LED_TOTAL)
```
!> Note the parentheses, this is so when `DRIVER_LED_TOTAL` is used in code and expanded, the values are added together before any additional math is applied to them. As an example, `rand() % (DRIVER_1_LED_TOTAL + DRIVER_2_LED_TOTAL)` will give very different results than `rand() % DRIVER_1_LED_TOTAL + DRIVER_2_LED_TOTAL`.
For split keyboards using `RGB_MATRIX_SPLIT` with an LED driver, you can either have the same driver address or different driver addresses. If using different addresses, use `DRIVER_ADDR_1` for one and `DRIVER_ADDR_2` for the other one. Then, in `g_is31_leds`, fill out the correct driver index (0 or 1). If using one address, use `DRIVER_ADDR_1` for both, and use index 0 for `g_is31_leds`.
Define these arrays listing all the LEDs in your `<keyboard>.c`:
```c
const is31_led PROGMEM g_is31_leds[DRIVER_LED_TOTAL] = {
/* Refer to IS31 manual for these locations
* driver
* | R location
* | | G location
* | | | B location
* | | | | */
{0, C1_3, C2_3, C3_3},
....
}
```
Where `Cx_y` is the location of the LED in the matrix defined by [the datasheet](https://www.issi.com/WW/pdf/31FL3731.pdf) and the header file `drivers/led/issi/is31fl3731.h`. The `driver` is the index of the driver you defined in your `config.h` (`0`, `1`, `2`, or `3`).
---
### IS31FL3733 :id=is31fl3733
There is basic support for addressable RGB matrix lighting with the I2C IS31FL3733 RGB controller. To enable it, add this to your `rules.mk`:
```make
RGB_MATRIX_ENABLE = yes
RGB_MATRIX_DRIVER = IS31FL3733
```
You can use between 1 and 4 IS31FL3733 IC's. Do not specify `DRIVER_ADDR_<N>` defines for IC's that are not present on your keyboard. You can define the following items in `config.h`:
| Variable | Description | Default |
|----------|-------------|---------|
| `ISSI_TIMEOUT` | (Optional) How long to wait for i2c messages, in milliseconds | 100 |
| `ISSI_PERSISTENCE` | (Optional) Retry failed messages this many times | 0 |
| `ISSI_PWM_FREQUENCY` | (Optional) PWM Frequency Setting - IS31FL3733B only | 0 |
| `ISSI_SWPULLUP` | (Optional) Set the value of the SWx lines on-chip de-ghosting resistors | PUR_0R (Disabled) |
| `ISSI_CSPULLUP` | (Optional) Set the value of the CSx lines on-chip de-ghosting resistors | PUR_0R (Disabled) |
| `DRIVER_COUNT` | (Required) How many RGB driver IC's are present | |
| `DRIVER_LED_TOTAL` | (Required) How many RGB lights are present across all drivers | |
| `DRIVER_ADDR_1` | (Required) Address for the first RGB driver | |
| `DRIVER_ADDR_2` | (Optional) Address for the second RGB driver | |
| `DRIVER_ADDR_3` | (Optional) Address for the third RGB driver | |
| `DRIVER_ADDR_4` | (Optional) Address for the fourth RGB driver | |
| `DRIVER_SYNC_1` | (Optional) Sync configuration for the first RGB driver | 0 |
| `DRIVER_SYNC_2` | (Optional) Sync configuration for the second RGB driver | 0 |
| `DRIVER_SYNC_3` | (Optional) Sync configuration for the third RGB driver | 0 |
| `DRIVER_SYNC_4` | (Optional) Sync configuration for the fourth RGB driver | 0 |
The IS31FL3733 IC's have on-chip resistors that can be enabled to allow for de-ghosting of the RGB matrix. By default these resistors are not enabled (`ISSI_SWPULLUP`/`ISSI_CSPULLUP` are given the value of`PUR_0R`), the values that can be set to enable de-ghosting are as follows:
| `ISSI_SWPULLUP/ISSI_CSPULLUP` | Description |
|----------------------|-------------|
| `PUR_0R` | (default) Do not use the on-chip resistors/enable de-ghosting |
| `PUR_05KR` | The 0.5k Ohm resistor used during blanking period (t_NOL) |
| `PUR_3KR` | The 3k Ohm resistor used at all times |
| `PUR_4KR` | The 4k Ohm resistor used at all times |
| `PUR_8KR` | The 8k Ohm resistor used at all times |
| `PUR_16KR` | The 16k Ohm resistor used at all times |
| `PUR_32KR` | The 32k Ohm resistor used during blanking period (t_NOL) |
Here is an example using 2 drivers.
```c
// This is a 7-bit address, that gets left-shifted and bit 0
// set to 0 for write, 1 for read (as per I2C protocol)
// The address will vary depending on your wiring:
// 00 <-> GND
// 01 <-> SCL
// 10 <-> SDA
// 11 <-> VCC
// ADDR1 represents A1:A0 of the 7-bit address.
// ADDR2 represents A3:A2 of the 7-bit address.
// The result is: 0b101(ADDR2)(ADDR1)
#define DRIVER_ADDR_1 0b1010000
#define DRIVER_ADDR_2 0b1010011
#define DRIVER_COUNT 2
#define DRIVER_1_LED_TOTAL 58
#define DRIVER_2_LED_TOTAL 10
#define DRIVER_LED_TOTAL (DRIVER_1_LED_TOTAL + DRIVER_2_LED_TOTAL)
```
!> Note the parentheses, this is so when `DRIVER_LED_TOTAL` is used in code and expanded, the values are added together before any additional math is applied to them. As an example, `rand() % (DRIVER_1_LED_TOTAL + DRIVER_2_LED_TOTAL)` will give very different results than `rand() % DRIVER_1_LED_TOTAL + DRIVER_2_LED_TOTAL`.
Currently only 4 drivers are supported, but it would be trivial to support all 8 combinations.
Define these arrays listing all the LEDs in your `<keyboard>.c`:
```c
const is31_led PROGMEM g_is31_leds[DRIVER_LED_TOTAL] = {
/* Refer to IS31 manual for these locations
* driver
* | R location
* | | G location
* | | | B location
* | | | | */
{0, B_1, A_1, C_1},
....
}
```
Where `X_Y` is the location of the LED in the matrix defined by [the datasheet](https://www.issi.com/WW/pdf/31FL3733.pdf) and the header file `drivers/led/issi/is31fl3733.h`. The `driver` is the index of the driver you defined in your `config.h` (`0`, `1`, `2`, or `3` for now).
---
### IS31FL3737 :id=is31fl3737
There is basic support for addressable RGB matrix lighting with the I2C IS31FL3737 RGB controller. To enable it, add this to your `rules.mk`:
```make
RGB_MATRIX_ENABLE = yes
RGB_MATRIX_DRIVER = IS31FL3737
```
You can use between 1 and 2 IS31FL3737 IC's. Do not specify `DRIVER_ADDR_2` define for second IC if not present on your keyboard.
Configure the hardware via your `config.h`:
| Variable | Description | Default |
|----------|-------------|---------|
| `ISSI_TIMEOUT` | (Optional) How long to wait for i2c messages, in milliseconds | 100 |
| `ISSI_PERSISTENCE` | (Optional) Retry failed messages this many times | 0 |
| `ISSI_SWPULLUP` | (Optional) Set the value of the SWx lines on-chip de-ghosting resistors | PUR_0R (Disabled) |
| `ISSI_CSPULLUP` | (Optional) Set the value of the CSx lines on-chip de-ghosting resistors | PUR_0R (Disabled) |
| `DRIVER_COUNT` | (Required) How many RGB driver IC's are present | |
| `DRIVER_LED_TOTAL` | (Required) How many RGB lights are present across all drivers | |
| `DRIVER_ADDR_1` | (Required) Address for the first RGB driver | |
| `DRIVER_ADDR_2` | (Optional) Address for the second RGB driver | |
The IS31FL3737 IC's have on-chip resistors that can be enabled to allow for de-ghosting of the RGB matrix. By default these resistors are not enabled (`ISSI_SWPULLUP`/`ISSI_CSPULLUP` are given the value of`PUR_0R`), the values that can be set to enable de-ghosting are as follows:
| `ISSI_SWPULLUP/ISSI_CSPULLUP` | Description |
|----------------------|-------------|
| `PUR_0R` | (default) Do not use the on-chip resistors/enable de-ghosting |
| `PUR_05KR` | The 0.5k Ohm resistor used during blanking period (t_NOL) |
| `PUR_1KR` | The 1k Ohm resistor used during blanking period (t_NOL) |
| `PUR_2KR` | The 2k Ohm resistor used during blanking period (t_NOL) |
| `PUR_4KR` | The 4k Ohm resistor used during blanking period (t_NOL) |
| `PUR_8KR` | The 8k Ohm resistor during blanking period (t_NOL) |
| `PUR_16KR` | The 16k Ohm resistor during blanking period (t_NOL) |
| `PUR_32KR` | The 32k Ohm resistor used during blanking period (t_NOL) |
Here is an example using 2 drivers.
```c
// This is a 7-bit address, that gets left-shifted and bit 0
// set to 0 for write, 1 for read (as per I2C protocol)
// The address will vary depending on your wiring:
// 0000 <-> GND
// 0101 <-> SCL
// 1010 <-> SDA
// 1111 <-> VCC
// ADDR represents A3:A0 of the 7-bit address.
// The result is: 0b101(ADDR)
#define DRIVER_ADDR_1 0b1010000
#define DRIVER_ADDR_2 0b1010001
#define DRIVER_COUNT 2
#define DRIVER_1_LED_TOTAL 30
#define DRIVER_2_LED_TOTAL 36
#define DRIVER_LED_TOTAL (DRIVER_1_LED_TOTAL + DRIVER_2_LED_TOTAL)
```
!> Note the parentheses, this is so when `DRIVER_LED_TOTAL` is used in code and expanded, the values are added together before any additional math is applied to them. As an example, `rand() % (DRIVER_1_LED_TOTAL + DRIVER_2_LED_TOTAL)` will give very different results than `rand() % DRIVER_1_LED_TOTAL + DRIVER_2_LED_TOTAL`.
Currently only 2 drivers are supported, but it would be trivial to support all 4 combinations.
Define these arrays listing all the LEDs in your `<keyboard>.c`:
```c
const is31_led PROGMEM g_is31_leds[DRIVER_LED_TOTAL] = {
/* Refer to IS31 manual for these locations
* driver
* | R location
* | | G location
* | | | B location
* | | | | */
{0, B_1, A_1, C_1},
....
}
```
Where `X_Y` is the location of the LED in the matrix defined by [the datasheet](https://www.issi.com/WW/pdf/31FL3737.pdf) and the header file `drivers/led/issi/is31fl3737.h`. The `driver` is the index of the driver you defined in your `config.h` (Only `0`, `1` for now).
---
### WS2812 :id=ws2812
There is basic support for addressable RGB matrix lighting with a WS2811/WS2812{a,b,c} addressable LED strand. To enable it, add this to your `rules.mk`:
```make
RGB_MATRIX_ENABLE = yes
RGB_MATRIX_DRIVER = WS2812
```
Configure the hardware via your `config.h`:
```c
// The pin connected to the data pin of the LEDs
#define RGB_DI_PIN D7
// The number of LEDs connected
#define DRIVER_LED_TOTAL 70
```
---
### APA102 :id=apa102
There is basic support for APA102 based addressable LED strands. To enable it, add this to your `rules.mk`:
```make
RGB_MATRIX_ENABLE = yes
RGB_MATRIX_DRIVER = APA102
```
Configure the hardware via your `config.h`:
```c
// The pin connected to the data pin of the LEDs
#define RGB_DI_PIN D7
// The pin connected to the clock pin of the LEDs
#define RGB_CI_PIN D6
// The number of LEDs connected
#define DRIVER_LED_TOTAL 70
```
---
### AW20216 :id=aw20216
There is basic support for addressable RGB matrix lighting with the SPI AW20216 RGB controller. To enable it, add this to your `rules.mk`:
```make
RGB_MATRIX_ENABLE = yes
RGB_MATRIX_DRIVER = AW20216
```
You can use up to 2 AW20216 IC's. Do not specify `DRIVER_<N>_xxx` defines for IC's that are not present on your keyboard. You can define the following items in `config.h`:
| Variable | Description | Default |
|----------|-------------|---------|
| `DRIVER_1_CS` | (Required) MCU pin connected to first RGB driver chip select line | B13 |
| `DRIVER_2_CS` | (Optional) MCU pin connected to second RGB driver chip select line | |
| `DRIVER_1_EN` | (Required) MCU pin connected to first RGB driver hardware enable line | C13 |
| `DRIVER_2_EN` | (Optional) MCU pin connected to second RGB driver hardware enable line | |
| `DRIVER_1_LED_TOTAL` | (Required) How many RGB lights are connected to first RGB driver | |
| `DRIVER_2_LED_TOTAL` | (Optional) How many RGB lights are connected to second RGB driver | |
| `DRIVER_COUNT` | (Required) How many RGB driver IC's are present | |
| `DRIVER_LED_TOTAL` | (Required) How many RGB lights are present across all drivers | |
| `AW_SCALING_MAX` | (Optional) LED current scaling value (0-255, higher values mean LED is brighter at full PWM) | 150 |
| `AW_GLOBAL_CURRENT_MAX` | (Optional) Driver global current limit (0-255, higher values means the driver may consume more power) | 150 |
| `AW_SPI_DIVISOR` | (Optional) Clock divisor for SPI communication (powers of 2, smaller numbers means faster communication, should not be less than 4) | 4 |
Here is an example using 2 drivers.
```c
#define DRIVER_1_CS B13
#define DRIVER_2_CS B14
// Hardware enable lines may be connected to the same pin
#define DRIVER_1_EN C13
#define DRIVER_2_EN C13
#define DRIVER_COUNT 2
#define DRIVER_1_LED_TOTAL 66
#define DRIVER_2_LED_TOTAL 32
#define DRIVER_LED_TOTAL (DRIVER_1_LED_TOTAL + DRIVER_2_LED_TOTAL)
```
!> Note the parentheses, this is so when `DRIVER_LED_TOTAL` is used in code and expanded, the values are added together before any additional math is applied to them. As an example, `rand() % (DRIVER_1_LED_TOTAL + DRIVER_2_LED_TOTAL)` will give very different results than `rand() % DRIVER_1_LED_TOTAL + DRIVER_2_LED_TOTAL`.
Define these arrays listing all the LEDs in your `<keyboard>.c`:
```c
const aw_led PROGMEM g_aw_leds[DRIVER_LED_TOTAL] = {
/* Each AW20216 channel is controlled by a register at some offset between 0x00
* and 0xD7 inclusive.
* See drivers/awinic/aw20216.h for the mapping between register offsets and
* driver pin locations.
* driver
* | R location
* | | G location
* | | | B location
* | | | | */
{ 0, CS1_SW1, CS2_SW1, CS3_SW1 },
{ 0, CS4_SW1, CS5_SW1, CS6_SW1 },
{ 0, CS7_SW1, CS8_SW1, CS9_SW1 },
{ 0, CS10_SW1, CS11_SW1, CS12_SW1 },
{ 0, CS13_SW1, CS14_SW1, CS15_SW1 },
...
{ 1, CS1_SW1, CS2_SW1, CS3_SW1 },
{ 1, CS13_SW1, CS14_SW1, CS15_SW1 },
{ 1, CS16_SW1, CS17_SW1, CS18_SW1 },
{ 1, CS4_SW2, CS5_SW2, CS6_SW2 },
...
};
```
---
## Common Configuration :id=common-configuration
From this point forward the configuration is the same for all the drivers. The `led_config_t` struct provides a key electrical matrix to led index lookup table, what the physical position of each LED is on the board, and what type of key or usage the LED if the LED represents. Here is a brief example:
```c
led_config_t g_led_config = { {
// Key Matrix to LED Index
{ 5, NO_LED, NO_LED, 0 },
{ NO_LED, NO_LED, NO_LED, NO_LED },
{ 4, NO_LED, NO_LED, 1 },
{ 3, NO_LED, NO_LED, 2 }
}, {
// LED Index to Physical Position
{ 188, 16 }, { 187, 48 }, { 149, 64 }, { 112, 64 }, { 37, 48 }, { 38, 16 }
}, {
// LED Index to Flag
1, 4, 4, 4, 4, 1
} };
```
The first part, `// Key Matrix to LED Index`, tells the system what key this LED represents by using the key's electrical matrix row & col. The second part, `// LED Index to Physical Position` represents the LED's physical `{ x, y }` position on the keyboard. The default expected range of values for `{ x, y }` is the inclusive range `{ 0..224, 0..64 }`. This default expected range is due to effects that calculate the center of the keyboard for their animations. The easiest way to calculate these positions is imagine your keyboard is a grid, and the top left of the keyboard represents `{ x, y }` coordinate `{ 0, 0 }` and the bottom right of your keyboard represents `{ 224, 64 }`. Using this as a basis, you can use the following formula to calculate the physical position:
```c
x = 224 / (NUMBER_OF_COLS - 1) * COL_POSITION
y = 64 / (NUMBER_OF_ROWS - 1) * ROW_POSITION
```
Where NUMBER_OF_COLS, NUMBER_OF_ROWS, COL_POSITION, & ROW_POSITION are all based on the physical layout of your keyboard, not the electrical layout.
As mentioned earlier, the center of the keyboard by default is expected to be `{ 112, 32 }`, but this can be changed if you want to more accurately calculate the LED's physical `{ x, y }` positions. Keyboard designers can implement `#define RGB_MATRIX_CENTER { 112, 32 }` in their config.h file with the new center point of the keyboard, or where they want it to be allowing more possibilities for the `{ x, y }` values. Do note that the maximum value for x or y is 255, and the recommended maximum is 224 as this gives animations runoff room before they reset.
`// LED Index to Flag` is a bitmask, whether or not a certain LEDs is of a certain type. It is recommended that LEDs are set to only 1 type.
## Flags :id=flags
|Define |Value |Description |
|----------------------------|------|-------------------------------------------------|
|`HAS_FLAGS(bits, flags)` |*n/a* |Evaluates to `true` if `bits` has all `flags` set|
|`HAS_ANY_FLAGS(bits, flags)`|*n/a* |Evaluates to `true` if `bits` has any `flags` set|
|`LED_FLAG_NONE` |`0x00`|If this LED has no flags |
|`LED_FLAG_ALL` |`0xFF`|If this LED has all flags |
|`LED_FLAG_MODIFIER` |`0x01`|If the LED is on a modifier key |
|`LED_FLAG_UNDERGLOW` |`0x02`|If the LED is for underglow |
|`LED_FLAG_KEYLIGHT` |`0x04`|If the LED is for key backlight |
|`LED_FLAG_INDICATOR` |`0x08`|If the LED is for keyboard state indication |
## Keycodes :id=keycodes
All RGB keycodes are currently shared with the RGBLIGHT system:
|Key |Aliases |Description |
|-------------------|----------|--------------------------------------------------------------------------------------|
|`RGB_TOG` | |Toggle RGB lighting on or off |
|`RGB_MODE_FORWARD` |`RGB_MOD` |Cycle through modes, reverse direction when Shift is held |
|`RGB_MODE_REVERSE` |`RGB_RMOD`|Cycle through modes in reverse, forward direction when Shift is held |
|`RGB_HUI` | |Increase hue, decrease hue when Shift is held |
|`RGB_HUD` | |Decrease hue, increase hue when Shift is held |
|`RGB_SAI` | |Increase saturation, decrease saturation when Shift is held |
|`RGB_SAD` | |Decrease saturation, increase saturation when Shift is held |
|`RGB_VAI` | |Increase value (brightness), decrease value when Shift is held |
|`RGB_VAD` | |Decrease value (brightness), increase value when Shift is held |
|`RGB_SPI` | |Increase effect speed (does not support eeprom yet), decrease speed when Shift is held|
|`RGB_SPD` | |Decrease effect speed (does not support eeprom yet), increase speed when Shift is held|
|`RGB_MODE_PLAIN` |`RGB_M_P `|Static (no animation) mode |
|`RGB_MODE_BREATHE` |`RGB_M_B` |Breathing animation mode |
|`RGB_MODE_RAINBOW` |`RGB_M_R` |Full gradient scrolling left to right (uses the `RGB_MATRIX_CYCLE_LEFT_RIGHT` mode) |
|`RGB_MODE_SWIRL` |`RGB_M_SW`|Full gradient spinning pinwheel around center of keyboard (uses `RGB_MATRIX_CYCLE_PINWHEEL` mode) |
* `RGB_MODE_*` keycodes will generally work, but not all of the modes are currently mapped to the correct effects for the RGB Matrix system.
`RGB_MODE_PLAIN`, `RGB_MODE_BREATHE`, `RGB_MODE_RAINBOW`, and `RGB_MODE_SWIRL` are the only ones that are mapped properly. The rest don't have a direct equivalent, and are not mapped.
?> `RGB_*` keycodes cannot be used with functions like `tap_code16(RGB_HUD)` as they're not USB HID keycodes. If you wish to replicate similar behaviour in custom code within your firmware (e.g. inside `encoder_update_user()` or `process_record_user()`), the equivalent [RGB functions](#functions-idfunctions) should be used instead.
!> By default, if you have both the [RGB Light](feature_rgblight.md) and the RGB Matrix feature enabled, these keycodes will work for both features, at the same time. You can disable the keycode functionality by defining the `*_DISABLE_KEYCODES` option for the specific feature.
## RGB Matrix Effects :id=rgb-matrix-effects
All effects have been configured to support current configuration values (Hue, Saturation, Value, & Speed) unless otherwise noted below. These are the effects that are currently available:
```c
enum rgb_matrix_effects {
RGB_MATRIX_NONE = 0,
RGB_MATRIX_SOLID_COLOR = 1, // Static single hue, no speed support
RGB_MATRIX_ALPHAS_MODS, // Static dual hue, speed is hue for secondary hue
RGB_MATRIX_GRADIENT_UP_DOWN, // Static gradient top to bottom, speed controls how much gradient changes
RGB_MATRIX_GRADIENT_LEFT_RIGHT, // Static gradient left to right, speed controls how much gradient changes
RGB_MATRIX_BREATHING, // Single hue brightness cycling animation
RGB_MATRIX_BAND_SAT, // Single hue band fading saturation scrolling left to right
RGB_MATRIX_BAND_VAL, // Single hue band fading brightness scrolling left to right
RGB_MATRIX_BAND_PINWHEEL_SAT, // Single hue 3 blade spinning pinwheel fades saturation
RGB_MATRIX_BAND_PINWHEEL_VAL, // Single hue 3 blade spinning pinwheel fades brightness
RGB_MATRIX_BAND_SPIRAL_SAT, // Single hue spinning spiral fades saturation
RGB_MATRIX_BAND_SPIRAL_VAL, // Single hue spinning spiral fades brightness
RGB_MATRIX_CYCLE_ALL, // Full keyboard solid hue cycling through full gradient
RGB_MATRIX_CYCLE_LEFT_RIGHT, // Full gradient scrolling left to right
RGB_MATRIX_CYCLE_UP_DOWN, // Full gradient scrolling top to bottom
RGB_MATRIX_CYCLE_OUT_IN, // Full gradient scrolling out to in
RGB_MATRIX_CYCLE_OUT_IN_DUAL, // Full dual gradients scrolling out to in
RGB_MATRIX_RAINBOW_MOVING_CHEVRON, // Full gradent Chevron shapped scrolling left to right
RGB_MATRIX_CYCLE_PINWHEEL, // Full gradient spinning pinwheel around center of keyboard
RGB_MATRIX_CYCLE_SPIRAL, // Full gradient spinning spiral around center of keyboard
RGB_MATRIX_DUAL_BEACON, // Full gradient spinning around center of keyboard
RGB_MATRIX_RAINBOW_BEACON, // Full tighter gradient spinning around center of keyboard
RGB_MATRIX_RAINBOW_PINWHEELS, // Full dual gradients spinning two halfs of keyboard
RGB_MATRIX_RAINDROPS, // Randomly changes a single key's hue
RGB_MATRIX_JELLYBEAN_RAINDROPS, // Randomly changes a single key's hue and saturation
RGB_MATRIX_HUE_BREATHING, // Hue shifts up a slight ammount at the same time, then shifts back
RGB_MATRIX_HUE_PENDULUM, // Hue shifts up a slight ammount in a wave to the right, then back to the left
RGB_MATRIX_HUE_WAVE, // Hue shifts up a slight ammount and then back down in a wave to the right
RGB_MATRIX_PIXEL_FRACTAL, // Single hue fractal filled keys pulsing horizontally out to edges
RGB_MATRIX_PIXEL_FLOW, // Pulsing RGB flow along LED wiring with random hues
RGB_MATRIX_PIXEL_RAIN, // Randomly light keys with random hues
#if define(RGB_MATRIX_FRAMEBUFFER_EFFECTS)
RGB_MATRIX_TYPING_HEATMAP, // How hot is your WPM!
RGB_MATRIX_DIGITAL_RAIN, // That famous computer simulation
#endif
#if defined(RGB_MATRIX_KEYPRESSES) || defined(RGB_MATRIX_KEYRELEASES)
RGB_MATRIX_SOLID_REACTIVE_SIMPLE, // Pulses keys hit to hue & value then fades value out
RGB_MATRIX_SOLID_REACTIVE, // Static single hue, pulses keys hit to shifted hue then fades to current hue
RGB_MATRIX_SOLID_REACTIVE_WIDE // Hue & value pulse near a single key hit then fades value out
RGB_MATRIX_SOLID_REACTIVE_MULTIWIDE // Hue & value pulse near multiple key hits then fades value out
RGB_MATRIX_SOLID_REACTIVE_CROSS // Hue & value pulse the same column and row of a single key hit then fades value out
RGB_MATRIX_SOLID_REACTIVE_MULTICROSS // Hue & value pulse the same column and row of multiple key hits then fades value out
RGB_MATRIX_SOLID_REACTIVE_NEXUS // Hue & value pulse away on the same column and row of a single key hit then fades value out
RGB_MATRIX_SOLID_REACTIVE_MULTINEXUS // Hue & value pulse away on the same column and row of multiple key hits then fades value out
RGB_MATRIX_SPLASH, // Full gradient & value pulse away from a single key hit then fades value out
RGB_MATRIX_MULTISPLASH, // Full gradient & value pulse away from multiple key hits then fades value out
RGB_MATRIX_SOLID_SPLASH, // Hue & value pulse away from a single key hit then fades value out
RGB_MATRIX_SOLID_MULTISPLASH, // Hue & value pulse away from multiple key hits then fades value out
#endif
RGB_MATRIX_EFFECT_MAX
};
```
You can enable a single effect by defining `ENABLE_[EFFECT_NAME]` in your `config.h`:
|Define |Description |
|------------------------------------------------------|----------------------------------------------|
|`#define ENABLE_RGB_MATRIX_ALPHAS_MODS` |Enables `RGB_MATRIX_ALPHAS_MODS` |
|`#define ENABLE_RGB_MATRIX_GRADIENT_UP_DOWN` |Enables `RGB_MATRIX_GRADIENT_UP_DOWN` |
|`#define ENABLE_RGB_MATRIX_GRADIENT_LEFT_RIGHT` |Enables `RGB_MATRIX_GRADIENT_LEFT_RIGHT` |
|`#define ENABLE_RGB_MATRIX_BREATHING` |Enables `RGB_MATRIX_BREATHING` |
|`#define ENABLE_RGB_MATRIX_BAND_SAT` |Enables `RGB_MATRIX_BAND_SAT` |
|`#define ENABLE_RGB_MATRIX_BAND_VAL` |Enables `RGB_MATRIX_BAND_VAL` |
|`#define ENABLE_RGB_MATRIX_BAND_PINWHEEL_SAT` |Enables `RGB_MATRIX_BAND_PINWHEEL_SAT` |
|`#define ENABLE_RGB_MATRIX_BAND_PINWHEEL_VAL` |Enables `RGB_MATRIX_BAND_PINWHEEL_VAL` |
|`#define ENABLE_RGB_MATRIX_BAND_SPIRAL_SAT` |Enables `RGB_MATRIX_BAND_SPIRAL_SAT` |
|`#define ENABLE_RGB_MATRIX_BAND_SPIRAL_VAL` |Enables `RGB_MATRIX_BAND_SPIRAL_VAL` |
|`#define ENABLE_RGB_MATRIX_CYCLE_ALL` |Enables `RGB_MATRIX_CYCLE_ALL` |
|`#define ENABLE_RGB_MATRIX_CYCLE_LEFT_RIGHT` |Enables `RGB_MATRIX_CYCLE_LEFT_RIGHT` |
|`#define ENABLE_RGB_MATRIX_CYCLE_UP_DOWN` |Enables `RGB_MATRIX_CYCLE_UP_DOWN` |
|`#define ENABLE_RGB_MATRIX_RAINBOW_MOVING_CHEVRON` |Enables `RGB_MATRIX_RAINBOW_MOVING_CHEVRON` |
|`#define ENABLE_RGB_MATRIX_CYCLE_OUT_IN` |Enables `RGB_MATRIX_CYCLE_OUT_IN` |
|`#define ENABLE_RGB_MATRIX_CYCLE_OUT_IN_DUAL` |Enables `RGB_MATRIX_CYCLE_OUT_IN_DUAL` |
|`#define ENABLE_RGB_MATRIX_CYCLE_PINWHEEL` |Enables `RGB_MATRIX_CYCLE_PINWHEEL` |
|`#define ENABLE_RGB_MATRIX_CYCLE_SPIRAL` |Enables `RGB_MATRIX_CYCLE_SPIRAL` |
|`#define ENABLE_RGB_MATRIX_DUAL_BEACON` |Enables `RGB_MATRIX_DUAL_BEACON` |
|`#define ENABLE_RGB_MATRIX_RAINBOW_BEACON` |Enables `RGB_MATRIX_RAINBOW_BEACON` |
|`#define ENABLE_RGB_MATRIX_RAINBOW_PINWHEELS` |Enables `RGB_MATRIX_RAINBOW_PINWHEELS` |
|`#define ENABLE_RGB_MATRIX_RAINDROPS` |Enables `RGB_MATRIX_RAINDROPS` |
|`#define ENABLE_RGB_MATRIX_JELLYBEAN_RAINDROPS` |Enables `RGB_MATRIX_JELLYBEAN_RAINDROPS` |
|`#define ENABLE_RGB_MATRIX_HUE_BREATHING` |Enables `RGB_MATRIX_HUE_BREATHING` |
|`#define ENABLE_RGB_MATRIX_HUE_PENDULUM` |Enables `RGB_MATRIX_HUE_PENDULUM` |
|`#define ENABLE_RGB_MATRIX_HUE_WAVE` |Enables `RGB_MATRIX_HUE_WAVE ` |
|`#define ENABLE_RGB_MATRIX_PIXEL_FRACTAL` |Enables `RGB_MATRIX_PIXEL_FRACTAL` |
|`#define ENABLE_RGB_MATRIX_PIXEL_FLOW` |Enables `RGB_MATRIX_PIXEL_FLOW` |
|`#define ENABLE_RGB_MATRIX_PIXEL_RAIN` |Enables `RGB_MATRIX_PIXEL_RAIN` |
?> These modes don't require any additional defines.
|Framebuffer Defines |Description |
|------------------------------------------------------|----------------------------------------------|
|`#define ENABLE_RGB_MATRIX_TYPING_HEATMAP` |Enables `RGB_MATRIX_TYPING_HEATMAP` |
|`#define ENABLE_RGB_MATRIX_DIGITAL_RAIN` |Enables `RGB_MATRIX_DIGITAL_RAIN` |
?> These modes also require the `RGB_MATRIX_FRAMEBUFFER_EFFECTS` define to be available.
|Reactive Defines |Description |
|------------------------------------------------------|----------------------------------------------|
|`#define ENABLE_RGB_MATRIX_SOLID_REACTIVE_SIMPLE` |Enables `RGB_MATRIX_SOLID_REACTIVE_SIMPLE` |
|`#define ENABLE_RGB_MATRIX_SOLID_REACTIVE` |Enables `RGB_MATRIX_SOLID_REACTIVE` |
|`#define ENABLE_RGB_MATRIX_SOLID_REACTIVE_WIDE` |Enables `RGB_MATRIX_SOLID_REACTIVE_WIDE` |
|`#define ENABLE_RGB_MATRIX_SOLID_REACTIVE_MULTIWIDE` |Enables `RGB_MATRIX_SOLID_REACTIVE_MULTIWIDE` |
|`#define ENABLE_RGB_MATRIX_SOLID_REACTIVE_CROSS` |Enables `RGB_MATRIX_SOLID_REACTIVE_CROSS` |
|`#define ENABLE_RGB_MATRIX_SOLID_REACTIVE_MULTICROSS` |Enables `RGB_MATRIX_SOLID_REACTIVE_MULTICROSS`|
|`#define ENABLE_RGB_MATRIX_SOLID_REACTIVE_NEXUS` |Enables `RGB_MATRIX_SOLID_REACTIVE_NEXUS` |
|`#define ENABLE_RGB_MATRIX_SOLID_REACTIVE_MULTINEXUS` |Enables `RGB_MATRIX_SOLID_REACTIVE_MULTINEXUS`|
|`#define ENABLE_RGB_MATRIX_SPLASH` |Enables `RGB_MATRIX_SPLASH` |
|`#define ENABLE_RGB_MATRIX_MULTISPLASH` |Enables `RGB_MATRIX_MULTISPLASH` |
|`#define ENABLE_RGB_MATRIX_SOLID_SPLASH` |Enables `RGB_MATRIX_SOLID_SPLASH` |
|`#define ENABLE_RGB_MATRIX_SOLID_MULTISPLASH` |Enables `RGB_MATRIX_SOLID_MULTISPLASH` |
?> These modes also require the `RGB_MATRIX_KEYPRESSES` or `RGB_MATRIX_KEYRELEASES` define to be available.
### RGB Matrix Effect Typing Heatmap :id=rgb-matrix-effect-typing-heatmap
This effect will color the RGB matrix according to a heatmap of recently pressed
keys. Whenever a key is pressed its "temperature" increases as well as that of
its neighboring keys. The temperature of each key is then decreased
automatically every 25 milliseconds by default.
In order to change the delay of temperature decrease define
`RGB_MATRIX_TYPING_HEATMAP_DECREASE_DELAY_MS`:
```c
#define RGB_MATRIX_TYPING_HEATMAP_DECREASE_DELAY_MS 50
```
## Custom RGB Matrix Effects :id=custom-rgb-matrix-effects
By setting `RGB_MATRIX_CUSTOM_USER = yes` in `rules.mk`, new effects can be defined directly from your keymap or userspace, without having to edit any QMK core files.
To declare new effects, create a `rgb_matrix_user.inc` file in the user keymap directory or userspace folder.
?> Hardware maintainers who want to limit custom effects to a specific
|