blob: 537e92e64fcc4092d9128ee24a02c0b97194c721 (
plain)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
|
PS/2 to USB keyboard converter
==============================
This firmware converts PS/2 keyboard protocol to USB.(It supports Scan Code Set 2.)
Connect Wires
-------------
In case of Teensy2.0(ATMega32U4):
1. Connect **Vcc** and **GND**.
2. Connect **Clock** and **Data** line.
- **Interrupt**: **Clock** is on `PD1` and **Data** on `PD0`.(Recommended. Soarer's converter compatible)
- **Busywait**: **Clock** is on `PD1` and **Data** on `PD0`.
- **USART**: **Clock** is on `PD5` and **Data** on `PD2`.
3. Optionally you need pull-up register. 1K-10K Ohm is OK.
To change pin configuration edit config.h.
Build Firmware
--------------
For **PJRC Teensy** just run `make`:
$ make clean
$ make
To select keymap:
$ make clean
$ make KEYMAP=[plain|jis|spacefn|...]
After that you will find HEX file `ps2_usb_lufa.hex` in current directory.
- For **TMK converter Rev.1** use `make -f Makefile.tmk_rev1` instead of `make` and HEX file is `ps2_usb_tmk_rev1.hex`.
- For **TMK converter Rev.2** use `make -f Makefile.tmk_rev2` instead of `make` and HEX file is `ps2_usb_tmk_rev2.hex`.
Keymap
------
Several version of keymap are available in advance but you are recommended to define your favorite layout yourself. To define your own keymap create file named `keymap_<name>.c` and see keymap document(you can find in README.md of top directory) and existent keymap files.
PS/2 signal handling implementations
------------------------------------
Following three methods can be used to implement PS/2 signal handling.
### Simple and stupid busy-wait(ps2_busywait.c)
This is expected to implemented with portable C code for reference.
### Interrupt driven(ps2_interrupt.c)
Uses pin interrupt to detect falling edge of clock line.
### USART hardware module(ps2_usart.c)
Uses AVR USART engine to receive PS/2 signal.
To select method edit Makefile.
V-USB Support
-------------
You can also use this converter on ATmega(168/328) with V-USB instead of Teensy.
The converter on V-USB lacks some features for now: USB NKRO and System/Media control.
Circuit:
+---+ +---------------+
USB GND | | ATmega168 |
=== C3 | |
5V <-------+--------+---|Vcc,AVCC | PS/2
R1 | | ====
D- <----+--+-----R2-----|INT1 RXD|------->DATA
D+ <----|---+----R3-----|INT0 XCK|------->CLOCK
Z1 Z2 | | ->5V
GND<----+---+--+--+-----|GND | ->GND
| | | |
| C2-+--|XTAL1 |
| X1 | |
+--C3-+--|XTAL2 |
+---------------+
R1: 1.5K Ohm
R2,R3: 68 Ohm
Z1,Z2: Zenner 3.6V
C1,C2: 22pF
C3: 0.1uF
X1: Crystal 20MHz(16MHz/12MHz)
|
