/* Converter for 70% IBM Terminal Keyboard Author: Benjamin Gould, 2013 Based on code Copyright 2011 Jun Wako <wakojun@gmail.com> This program is free software: you can redistribute it and/or modify it under the terms of the GNU General Public License as published by the Free Software Foundation, either version 2 of the License, or (at your option) any later version. This program is distributed in the hope that it will be useful, but WITHOUT ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for more details. You should have received a copy of the GNU General Public License along with this program. If not, see <http://www.gnu.org/licenses/>. */ #ifndef CONFIG_H #define CONFIG_H #define VENDOR_ID 0xFEED #define PRODUCT_ID 0x6535 #define DEVICE_VER 0x0100 #define MANUFACTURER t.m.k. #define PRODUCT 70% IBM Terminal Keyboard Converter w/ Bluetooth #define DESCRIPTION USB converter for IBM Terminal Keyboard w/ Bluetooth /* matrix size */ #define MATRIX_ROWS 17 // keycode bit: 3-0 #define MATRIX_COLS 8 // keycode bit: 6-4 /* legacy keymap support */ // #define USE_LEGACY_KEYMAP /* key combination for command */ #define IS_COMMAND() ( \ (keyboard_report->mods == (MOD_BIT(KC_LSHIFT) | MOD_BIT(KC_RSHIFT))) || \ (keyboard_report->mods == (MOD_BIT(KC_RALT) | MOD_BIT(KC_RCTL))) \ ) /* USART configuration * asynchronous, 9600baud, 8-data bit, non parity, 1-stop bit, no flow control */ #ifdef __AVR_ATmega32U4__ #define SERIAL_UART_BAUD 9600 #define SERIAL_UART_DATA UDR1 #define SERIAL_UART_UBRR ((F_CPU/(16UL*SERIAL_UART_BAUD))-1) #define SERIAL_UART_RXD_VECT USART1_RX_vect #define SERIAL_UART_TXD_READY (UCSR1A&(1<<UDRE1)) #define SERIAL_UART_INIT() do { \ UBRR1L = (uint8_t) SERIAL_UART_UBRR; /* baud rate */ \ UBRR1H = (uint8_t) (SERIAL_UART_UBRR>>8); /* baud rate */ \ UCSR1B = (1<<TXEN1); /* TX: enable */ \ UCSR1C = (0<<UPM11) | (0<<UPM10) | /* parity: none(00), even(01), odd(11) */ \ (0<<UCSZ12) | (1<<UCSZ11) | (1<<UCSZ10); /* data-8bit(011) */ \ sei(); \ } while(0) #else # error "USART configuration is needed." #endif /* * PS/2 Interrupt configuration */ #ifdef PS2_USE_INT /* uses INT1 for clock line(ATMega32U4) */ #define PS2_CLOCK_PORT PORTD #define PS2_CLOCK_PIN PIND #define PS2_CLOCK_DDR DDRD #define PS2_CLOCK_BIT 1 #define PS2_DATA_PORT PORTD #define PS2_DATA_PIN PIND #define PS2_DATA_DDR DDRD #define PS2_DATA_BIT 0 #define PS2_INT_INIT() do { \ EICRA |= ((1<<ISC11) | \ (0<<ISC10)); \ } while (0) #define PS2_INT_ON() do { \ EIMSK |= (1<<INT1); \ } while (0) #define PS2_INT_OFF() do { \ EIMSK &= ~(1<<INT1); \ } while (0) #define PS2_INT_VECT INT1_vect #endif /* * PS/2 Busywait configuration */ #ifdef PS2_USE_BUSYWAIT #define PS2_CLOCK_PORT PORTD #define PS2_CLOCK_PIN PIND #define PS2_CLOCK_DDR DDRD #define PS2_CLOCK_BIT 1 #define PS2_DATA_PORT PORTD #define PS2_DATA_PIN PIND #define PS2_DATA_DDR DDRD #define PS2_DATA_BIT 0 #endif #endif