From f209f91c7ce073aa0381e79c10219616cb7db523 Mon Sep 17 00:00:00 2001 From: Ryan Date: Sun, 7 Jun 2020 15:00:21 +1000 Subject: Various tidyups for USB descriptor code (#9005) --- tmk_core/protocol/lufa/lufa.c | 120 +++++++++++++++++++++--------------------- 1 file changed, 61 insertions(+), 59 deletions(-) (limited to 'tmk_core/protocol/lufa/lufa.c') diff --git a/tmk_core/protocol/lufa/lufa.c b/tmk_core/protocol/lufa/lufa.c index 374add20f9..19f417770f 100644 --- a/tmk_core/protocol/lufa/lufa.c +++ b/tmk_core/protocol/lufa/lufa.c @@ -88,7 +88,7 @@ extern keymap_config_t keymap_config; uint8_t keyboard_idle = 0; /* 0: Boot Protocol, 1: Report Protocol(default) */ uint8_t keyboard_protocol = 1; -static uint8_t keyboard_led_stats = 0; +static uint8_t keyboard_led_state = 0; static report_keyboard_t keyboard_report_sent; @@ -103,30 +103,30 @@ host_driver_t lufa_driver = { }; #ifdef VIRTSER_ENABLE +// clang-format off + USB_ClassInfo_CDC_Device_t cdc_device = { - .Config = - { - .ControlInterfaceNumber = CCI_INTERFACE, - .DataINEndpoint = - { - .Address = CDC_IN_EPADDR, - .Size = CDC_EPSIZE, - .Banks = 1, - }, - .DataOUTEndpoint = - { - .Address = CDC_OUT_EPADDR, - .Size = CDC_EPSIZE, - .Banks = 1, - }, - .NotificationEndpoint = - { - .Address = CDC_NOTIFICATION_EPADDR, - .Size = CDC_NOTIFICATION_EPSIZE, - .Banks = 1, - }, + .Config = { + .ControlInterfaceNumber = CCI_INTERFACE, + .DataINEndpoint = { + .Address = (CDC_IN_EPNUM | ENDPOINT_DIR_IN), + .Size = CDC_EPSIZE, + .Banks = 1 + }, + .DataOUTEndpoint = { + .Address = (CDC_OUT_EPNUM | ENDPOINT_DIR_OUT), + .Size = CDC_EPSIZE, + .Banks = 1 }, + .NotificationEndpoint = { + .Address = (CDC_NOTIFICATION_EPNUM | ENDPOINT_DIR_IN), + .Size = CDC_NOTIFICATION_EPSIZE, + .Banks = 1 + } + } }; + +// clang-format on #endif #ifdef RAW_ENABLE @@ -254,7 +254,7 @@ static void Console_Task(void) { // fill empty bank while (Endpoint_IsReadWriteAllowed()) Endpoint_Write_8(0); - // flash senchar packet + // flush sendchar packet if (Endpoint_IsINReady()) { Endpoint_ClearIN(); } @@ -370,45 +370,46 @@ void EVENT_USB_Device_StartOfFrame(void) { void EVENT_USB_Device_ConfigurationChanged(void) { bool ConfigSuccess = true; - /* Setup Keyboard HID Report Endpoints */ #ifndef KEYBOARD_SHARED_EP - ConfigSuccess &= ENDPOINT_CONFIG(KEYBOARD_IN_EPNUM, EP_TYPE_INTERRUPT, ENDPOINT_DIR_IN, KEYBOARD_EPSIZE, ENDPOINT_BANK_SINGLE); + /* Setup keyboard report endpoint */ + ConfigSuccess &= Endpoint_ConfigureEndpoint((KEYBOARD_IN_EPNUM | ENDPOINT_DIR_IN), EP_TYPE_INTERRUPT, KEYBOARD_EPSIZE, 1); #endif #if defined(MOUSE_ENABLE) && !defined(MOUSE_SHARED_EP) - /* Setup Mouse HID Report Endpoint */ - ConfigSuccess &= ENDPOINT_CONFIG(MOUSE_IN_EPNUM, EP_TYPE_INTERRUPT, ENDPOINT_DIR_IN, MOUSE_EPSIZE, ENDPOINT_BANK_SINGLE); + /* Setup mouse report endpoint */ + ConfigSuccess &= Endpoint_ConfigureEndpoint((MOUSE_IN_EPNUM | ENDPOINT_DIR_IN), EP_TYPE_INTERRUPT, MOUSE_EPSIZE, 1); #endif #ifdef SHARED_EP_ENABLE - /* Setup Shared HID Report Endpoint */ - ConfigSuccess &= ENDPOINT_CONFIG(SHARED_IN_EPNUM, EP_TYPE_INTERRUPT, ENDPOINT_DIR_IN, SHARED_EPSIZE, ENDPOINT_BANK_SINGLE); + /* Setup shared report endpoint */ + ConfigSuccess &= Endpoint_ConfigureEndpoint((SHARED_IN_EPNUM | ENDPOINT_DIR_IN), EP_TYPE_INTERRUPT, SHARED_EPSIZE, 1); #endif #ifdef RAW_ENABLE - /* Setup Raw HID Report Endpoints */ - ConfigSuccess &= ENDPOINT_CONFIG(RAW_IN_EPNUM, EP_TYPE_INTERRUPT, ENDPOINT_DIR_IN, RAW_EPSIZE, ENDPOINT_BANK_SINGLE); - ConfigSuccess &= ENDPOINT_CONFIG(RAW_OUT_EPNUM, EP_TYPE_INTERRUPT, ENDPOINT_DIR_OUT, RAW_EPSIZE, ENDPOINT_BANK_SINGLE); + /* Setup raw HID endpoints */ + ConfigSuccess &= Endpoint_ConfigureEndpoint((RAW_IN_EPNUM | ENDPOINT_DIR_IN), EP_TYPE_INTERRUPT, RAW_EPSIZE, 1); + ConfigSuccess &= Endpoint_ConfigureEndpoint((RAW_OUT_EPNUM | ENDPOINT_DIR_OUT), EP_TYPE_INTERRUPT, RAW_EPSIZE, 1); #endif #ifdef CONSOLE_ENABLE - /* Setup Console HID Report Endpoints */ - ConfigSuccess &= ENDPOINT_CONFIG(CONSOLE_IN_EPNUM, EP_TYPE_INTERRUPT, ENDPOINT_DIR_IN, CONSOLE_EPSIZE, ENDPOINT_BANK_SINGLE); + /* Setup console endpoint */ + ConfigSuccess &= Endpoint_ConfigureEndpoint((CONSOLE_IN_EPNUM | ENDPOINT_DIR_IN), EP_TYPE_INTERRUPT, CONSOLE_EPSIZE, 1); # if 0 - ConfigSuccess &= ENDPOINT_CONFIG(CONSOLE_OUT_EPNUM, EP_TYPE_INTERRUPT, ENDPOINT_DIR_OUT, - CONSOLE_EPSIZE, ENDPOINT_BANK_SINGLE); + ConfigSuccess &= Endpoint_ConfigureEndpoint((CONSOLE_OUT_EPNUM | ENDPOINT_DIR_OUT), EP_TYPE_INTERRUPT, CONSOLE_EPSIZE, 1); # endif #endif #ifdef MIDI_ENABLE - ConfigSuccess &= Endpoint_ConfigureEndpoint(MIDI_STREAM_IN_EPADDR, EP_TYPE_BULK, MIDI_STREAM_EPSIZE, ENDPOINT_BANK_SINGLE); - ConfigSuccess &= Endpoint_ConfigureEndpoint(MIDI_STREAM_OUT_EPADDR, EP_TYPE_BULK, MIDI_STREAM_EPSIZE, ENDPOINT_BANK_SINGLE); + /* Setup MIDI stream endpoints */ + ConfigSuccess &= Endpoint_ConfigureEndpoint((MIDI_STREAM_IN_EPNUM | ENDPOINT_DIR_IN), EP_TYPE_BULK, MIDI_STREAM_EPSIZE, 1); + ConfigSuccess &= Endpoint_ConfigureEndpoint((MIDI_STREAM_OUT_EPNUM | ENDPOINT_DIR_IN), EP_TYPE_BULK, MIDI_STREAM_EPSIZE, 1); #endif #ifdef VIRTSER_ENABLE - ConfigSuccess &= Endpoint_ConfigureEndpoint(CDC_NOTIFICATION_EPADDR, EP_TYPE_INTERRUPT, CDC_NOTIFICATION_EPSIZE, ENDPOINT_BANK_SINGLE); - ConfigSuccess &= Endpoint_ConfigureEndpoint(CDC_OUT_EPADDR, EP_TYPE_BULK, CDC_EPSIZE, ENDPOINT_BANK_SINGLE); - ConfigSuccess &= Endpoint_ConfigureEndpoint(CDC_IN_EPADDR, EP_TYPE_BULK, CDC_EPSIZE, ENDPOINT_BANK_SINGLE); + /* Setup virtual serial endpoints */ + ConfigSuccess &= Endpoint_ConfigureEndpoint((CDC_NOTIFICATION_EPNUM | ENDPOINT_DIR_IN), EP_TYPE_INTERRUPT, CDC_NOTIFICATION_EPSIZE, 1); + ConfigSuccess &= Endpoint_ConfigureEndpoint((CDC_OUT_EPNUM | ENDPOINT_DIR_OUT), EP_TYPE_BULK, CDC_EPSIZE, 1); + ConfigSuccess &= Endpoint_ConfigureEndpoint((CDC_IN_EPNUM | ENDPOINT_DIR_IN), EP_TYPE_BULK, CDC_EPSIZE, 1); #endif } @@ -472,10 +473,10 @@ void EVENT_USB_Device_ControlRequest(void) { uint8_t report_id = Endpoint_Read_8(); if (report_id == REPORT_ID_KEYBOARD || report_id == REPORT_ID_NKRO) { - keyboard_led_stats = Endpoint_Read_8(); + keyboard_led_state = Endpoint_Read_8(); } } else { - keyboard_led_stats = Endpoint_Read_8(); + keyboard_led_state = Endpoint_Read_8(); } Endpoint_ClearOUT(); @@ -545,7 +546,7 @@ void EVENT_USB_Device_ControlRequest(void) { * * FIXME: Needs doc */ -static uint8_t keyboard_leds(void) { return keyboard_led_stats; } +static uint8_t keyboard_leds(void) { return keyboard_led_state; } /** \brief Send Keyboard * @@ -808,25 +809,26 @@ ERROR_EXIT: ******************************************************************************/ #ifdef MIDI_ENABLE +// clang-format off + USB_ClassInfo_MIDI_Device_t USB_MIDI_Interface = { - .Config = - { - .StreamingInterfaceNumber = AS_INTERFACE, - .DataINEndpoint = - { - .Address = MIDI_STREAM_IN_EPADDR, - .Size = MIDI_STREAM_EPSIZE, - .Banks = 1, - }, - .DataOUTEndpoint = - { - .Address = MIDI_STREAM_OUT_EPADDR, - .Size = MIDI_STREAM_EPSIZE, - .Banks = 1, - }, + .Config = { + .StreamingInterfaceNumber = AS_INTERFACE, + .DataINEndpoint = { + .Address = (MIDI_STREAM_IN_EPNUM | ENDPOINT_DIR_IN), + .Size = MIDI_STREAM_EPSIZE, + .Banks = 1 }, + .DataOUTEndpoint = { + .Address = (MIDI_STREAM_OUT_EPNUM | ENDPOINT_DIR_OUT), + .Size = MIDI_STREAM_EPSIZE, + .Banks = 1 + } + } }; +// clang-format on + void send_midi_packet(MIDI_EventPacket_t *event) { MIDI_Device_SendEventPacket(&USB_MIDI_Interface, event); } bool recv_midi_packet(MIDI_EventPacket_t *const event) { return MIDI_Device_ReceiveEventPacket(&USB_MIDI_Interface, event); } -- cgit v1.2.3 From 1193e45bf4c8c69e33c054c6eb3d545d5d52fcb5 Mon Sep 17 00:00:00 2001 From: Ryan Date: Sun, 7 Jun 2020 15:00:59 +1000 Subject: Convert `CONSUMER2BLUEFRUIT()` and `CONSUMER2RN42()` macros to static inline functions (#9055) --- tmk_core/protocol/lufa/lufa.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'tmk_core/protocol/lufa/lufa.c') diff --git a/tmk_core/protocol/lufa/lufa.c b/tmk_core/protocol/lufa/lufa.c index 19f417770f..3ca1a809d1 100644 --- a/tmk_core/protocol/lufa/lufa.c +++ b/tmk_core/protocol/lufa/lufa.c @@ -720,8 +720,8 @@ static void send_consumer(uint16_t data) { bluefruit_serial_send(0xFD); bluefruit_serial_send(0x00); bluefruit_serial_send(0x02); - bluefruit_serial_send((bitmap >> 8) & 0xFF); bluefruit_serial_send(bitmap & 0xFF); + bluefruit_serial_send((bitmap >> 8) & 0xFF); bluefruit_serial_send(0x00); bluefruit_serial_send(0x00); bluefruit_serial_send(0x00); -- cgit v1.2.3 From 3b34858b772cda36fa9988e4d45039ff7ff9146a Mon Sep 17 00:00:00 2001 From: Ryan Date: Wed, 17 Jun 2020 21:43:20 +1000 Subject: Don't compile outputselect.c if Bluetooth is disabled (#9356) --- tmk_core/protocol/lufa/lufa.c | 16 +++++++++------- 1 file changed, 9 insertions(+), 7 deletions(-) (limited to 'tmk_core/protocol/lufa/lufa.c') diff --git a/tmk_core/protocol/lufa/lufa.c b/tmk_core/protocol/lufa/lufa.c index 3ca1a809d1..ca3384ba25 100644 --- a/tmk_core/protocol/lufa/lufa.c +++ b/tmk_core/protocol/lufa/lufa.c @@ -53,7 +53,6 @@ #include "lufa.h" #include "quantum.h" #include -#include "outputselect.h" #ifdef NKRO_ENABLE # include "keycode_config.h" @@ -66,6 +65,7 @@ extern keymap_config_t keymap_config; #endif #ifdef BLUETOOTH_ENABLE +# include "outputselect.h" # ifdef MODULE_ADAFRUIT_BLE # include "adafruit_ble.h" # else @@ -554,9 +554,10 @@ static uint8_t keyboard_leds(void) { return keyboard_led_state; } */ static void send_keyboard(report_keyboard_t *report) { uint8_t timeout = 255; - uint8_t where = where_to_send(); #ifdef BLUETOOTH_ENABLE + uint8_t where = where_to_send(); + if (where == OUTPUT_BLUETOOTH || where == OUTPUT_USB_AND_BT) { # ifdef MODULE_ADAFRUIT_BLE adafruit_ble_send_keys(report->mods, report->keys, sizeof(report->keys)); @@ -578,11 +579,11 @@ static void send_keyboard(report_keyboard_t *report) { } # endif } -#endif if (where != OUTPUT_USB && where != OUTPUT_USB_AND_BT) { return; } +#endif /* Select the Keyboard Report Endpoint */ uint8_t ep = KEYBOARD_IN_EPNUM; @@ -618,9 +619,10 @@ static void send_keyboard(report_keyboard_t *report) { static void send_mouse(report_mouse_t *report) { #ifdef MOUSE_ENABLE uint8_t timeout = 255; - uint8_t where = where_to_send(); # ifdef BLUETOOTH_ENABLE + uint8_t where = where_to_send(); + if (where == OUTPUT_BLUETOOTH || where == OUTPUT_USB_AND_BT) { # ifdef MODULE_ADAFRUIT_BLE // FIXME: mouse buttons @@ -637,11 +639,11 @@ static void send_mouse(report_mouse_t *report) { bluefruit_serial_send(0x00); # endif } -# endif if (where != OUTPUT_USB && where != OUTPUT_USB_AND_BT) { return; } +# endif /* Select the Mouse Report Endpoint */ Endpoint_SelectEndpoint(MOUSE_IN_EPNUM); @@ -696,9 +698,9 @@ static void send_system(uint16_t data) { */ static void send_consumer(uint16_t data) { #ifdef EXTRAKEY_ENABLE +# ifdef BLUETOOTH_ENABLE uint8_t where = where_to_send(); -# ifdef BLUETOOTH_ENABLE if (where == OUTPUT_BLUETOOTH || where == OUTPUT_USB_AND_BT) { # ifdef MODULE_ADAFRUIT_BLE adafruit_ble_send_consumer_key(data, 0); @@ -728,11 +730,11 @@ static void send_consumer(uint16_t data) { bluefruit_serial_send(0x00); # endif } -# endif if (where != OUTPUT_USB && where != OUTPUT_USB_AND_BT) { return; } +# endif send_extra(REPORT_ID_CONSUMER, data); #endif -- cgit v1.2.3 From 60e5733c487cc0435e7d3b913f31ce4acc405d4a Mon Sep 17 00:00:00 2001 From: Nick Brassel Date: Mon, 22 Jun 2020 11:22:00 +1000 Subject: `qmk cformat` on `develop` (#9501) --- tmk_core/protocol/lufa/lufa.c | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) (limited to 'tmk_core/protocol/lufa/lufa.c') diff --git a/tmk_core/protocol/lufa/lufa.c b/tmk_core/protocol/lufa/lufa.c index ca3384ba25..6776a964e9 100644 --- a/tmk_core/protocol/lufa/lufa.c +++ b/tmk_core/protocol/lufa/lufa.c @@ -556,7 +556,7 @@ static void send_keyboard(report_keyboard_t *report) { uint8_t timeout = 255; #ifdef BLUETOOTH_ENABLE - uint8_t where = where_to_send(); + uint8_t where = where_to_send(); if (where == OUTPUT_BLUETOOTH || where == OUTPUT_USB_AND_BT) { # ifdef MODULE_ADAFRUIT_BLE @@ -621,7 +621,7 @@ static void send_mouse(report_mouse_t *report) { uint8_t timeout = 255; # ifdef BLUETOOTH_ENABLE - uint8_t where = where_to_send(); + uint8_t where = where_to_send(); if (where == OUTPUT_BLUETOOTH || where == OUTPUT_USB_AND_BT) { # ifdef MODULE_ADAFRUIT_BLE -- cgit v1.2.3 From d4be07dad368c57669c88ead6c093c9e23086855 Mon Sep 17 00:00:00 2001 From: a-chol Date: Sat, 25 Jul 2020 14:01:15 +0200 Subject: Hid joystick interface (#4226) MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit * add support for hid gamepad interface add documentation for HID joystick Add joystick_task to read analog axes values even when no key is pressed or release. update doc Update docs/feature_joystick.md Manage pin setup and read to maintain matrix scan after analog read * Incorporates patches and changes to HID reporting There are some patches provided by @a-chol incorporated on this commit, and also some changes I made to the HID Report structure. The most interesting is the one dealing with number of buttons: Linux doesn't seem to care, but Windows requires the HID structure to be byte aligned (that's in the spec). So if one declares 8/16/32... buttons they should not have any issues, but this is what happens when you have 9 buttons: ``` bits |0|1|2|3|4|5|6|7| |*|*|*|*|*|*|*|*| axis 0 (report size 8) |*|*|*|*|*|*|*|*| ... |*|*|*|*|*|*|*|*| |*|*|*|*|*|*|*|*| |*|*|*|*|*|*|*|*| |*|*|*|*|*|*|*|*| |*|*|*|*|*|*|*|*| axis 6 |*|*|*|*|*|*|*|*| first 8 buttons (report size 1) |*| | | | | | | | last of 9 buttons, not aligned ``` So for that I added a conditonal that will add a number of reports with size 1 to make sure it aligns to the next multiple of 8. Those reports send dummy inputs that don't do anything aside from aligning the data. Tested on Linux, Windows 10 and Street Fighter (where the joystick is recognized as direct-input) * Add save and restore of each pin used in reading joystick (AVR). Allow output pin to be JS_VIRTUAL_AXIS if the axis is connected to Vcc instead of an output pin from the MCU. Fix joystick report id Fix broken v-usb hid joystick interface. Make it more resilient to unusual settings (none multiple of eight button count, 0 buttons or 0 axes) Correct adc reading for multiple axes. Piecewise range conversion for uncentered raw value range. Input, output and ground pin configuration per axis. Documentation fixes * Fix port addressing for joystick analog read * The other required set of changes As per the PR, the changes still holding it up. Add onekey for testing. Fix ARM builds. Fix device descriptor when either axes or buttons is zero. Add compile-time check for at least one axis or button. Move definition to try to fix conflict. PR review comments. qmk cformat * avoid float functions to compute range mapping for axis adc reading * Remove V-USB support for now. Updated docs accordingly. * Update tmk_core/protocol/lufa/lufa.c Co-Authored-By: Ryan * Update tmk_core/protocol/usb_descriptor.c Co-Authored-By: Ryan * Update tmk_core/protocol/usb_descriptor.c Co-Authored-By: Ryan * Update tmk_core/protocol/usb_descriptor.c Co-Authored-By: Ryan * Add support for joystick adc reading for stm32 MCUs. Fix joystick hid report sending for chibios * Fix HID joystick report sending for ChibiOS. Add one analog axis to the onekey:joystick keymap. Fix pin state save and restore during joystick analog read for STM32 MCUs. * Update tmk_core/protocol/chibios/usb_main.c Co-Authored-By: Ryan * Update tmk_core/protocol/lufa/lufa.c Co-Authored-By: Ryan * Add missing mcuconf.h and halconf.h to onekey:joystick keymap. Add suggested fixes from PR. * Switch saveState and restoreState signature to use pin_t type. onekey:joystick : add a second axis, virtual and programmatically animated. * Update docs/feature_joystick.md Co-Authored-By: Ryan * Update docs/feature_joystick.md Co-Authored-By: Ryan * Add PR corrections * Remove halconf.h and mcuconf.h from onekey keymaps * Change ADC_PIN to A0 Co-authored-by: achol Co-authored-by: José Júnior Co-authored-by: a-chol Co-authored-by: Nick Brassel Co-authored-by: Ryan --- tmk_core/protocol/lufa/lufa.c | 67 +++++++++++++++++++++++++++++++++++++++++++ 1 file changed, 67 insertions(+) (limited to 'tmk_core/protocol/lufa/lufa.c') diff --git a/tmk_core/protocol/lufa/lufa.c b/tmk_core/protocol/lufa/lufa.c index 6776a964e9..85603646db 100644 --- a/tmk_core/protocol/lufa/lufa.c +++ b/tmk_core/protocol/lufa/lufa.c @@ -85,6 +85,10 @@ extern keymap_config_t keymap_config; # include "raw_hid.h" #endif +#ifdef JOYSTICK_ENABLE +# include "joystick.h" +#endif + uint8_t keyboard_idle = 0; /* 0: Boot Protocol, 1: Report Protocol(default) */ uint8_t keyboard_protocol = 1; @@ -263,6 +267,66 @@ static void Console_Task(void) { } #endif +/******************************************************************************* + * Joystick + ******************************************************************************/ +#ifdef JOYSTICK_ENABLE +void send_joystick_packet(joystick_t *joystick) { + uint8_t timeout = 255; + + joystick_report_t r = { +# if JOYSTICK_AXES_COUNT > 0 + .axes = {joystick->axes[0], + +# if JOYSTICK_AXES_COUNT >= 2 + joystick->axes[1], +# endif +# if JOYSTICK_AXES_COUNT >= 3 + joystick->axes[2], +# endif +# if JOYSTICK_AXES_COUNT >= 4 + joystick->axes[3], +# endif +# if JOYSTICK_AXES_COUNT >= 5 + joystick->axes[4], +# endif +# if JOYSTICK_AXES_COUNT >= 6 + joystick->axes[5], +# endif + }, +# endif // JOYSTICK_AXES_COUNT>0 + +# if JOYSTICK_BUTTON_COUNT > 0 + .buttons = {joystick->buttons[0], + +# if JOYSTICK_BUTTON_COUNT > 8 + joystick->buttons[1], +# endif +# if JOYSTICK_BUTTON_COUNT > 16 + joystick->buttons[2], +# endif +# if JOYSTICK_BUTTON_COUNT > 24 + joystick->buttons[3], +# endif + } +# endif // JOYSTICK_BUTTON_COUNT>0 + }; + + /* Select the Joystick Report Endpoint */ + Endpoint_SelectEndpoint(JOYSTICK_IN_EPNUM); + + /* Check if write ready for a polling interval around 10ms */ + while (timeout-- && !Endpoint_IsReadWriteAllowed()) _delay_us(40); + if (!Endpoint_IsReadWriteAllowed()) return; + + /* Write Joystick Report Data */ + Endpoint_Write_Stream_LE(&r, sizeof(joystick_report_t), NULL); + + /* Finalize the stream transfer to send the last packet */ + Endpoint_ClearIN(); +} +#endif + /******************************************************************************* * USB Events ******************************************************************************/ @@ -411,6 +475,9 @@ void EVENT_USB_Device_ConfigurationChanged(void) { ConfigSuccess &= Endpoint_ConfigureEndpoint((CDC_OUT_EPNUM | ENDPOINT_DIR_OUT), EP_TYPE_BULK, CDC_EPSIZE, 1); ConfigSuccess &= Endpoint_ConfigureEndpoint((CDC_IN_EPNUM | ENDPOINT_DIR_IN), EP_TYPE_BULK, CDC_EPSIZE, 1); #endif +#ifdef JOYSTICK_ENABLE + ConfigSuccess &= ENDPOINT_CONFIG(JOYSTICK_IN_EPNUM, EP_TYPE_INTERRUPT, ENDPOINT_DIR_IN, JOYSTICK_EPSIZE, ENDPOINT_BANK_SINGLE); +#endif } /* FIXME: Expose this table in the docs somehow -- cgit v1.2.3 From 12333b7c5e47f935c8e11276caebae464331df8a Mon Sep 17 00:00:00 2001 From: Ryan Date: Sat, 8 Aug 2020 10:24:29 +1000 Subject: Fix joystick compile issues (#9949) --- tmk_core/protocol/lufa/lufa.c | 4 +++- 1 file changed, 3 insertions(+), 1 deletion(-) (limited to 'tmk_core/protocol/lufa/lufa.c') diff --git a/tmk_core/protocol/lufa/lufa.c b/tmk_core/protocol/lufa/lufa.c index 85603646db..8410eb483f 100644 --- a/tmk_core/protocol/lufa/lufa.c +++ b/tmk_core/protocol/lufa/lufa.c @@ -475,8 +475,10 @@ void EVENT_USB_Device_ConfigurationChanged(void) { ConfigSuccess &= Endpoint_ConfigureEndpoint((CDC_OUT_EPNUM | ENDPOINT_DIR_OUT), EP_TYPE_BULK, CDC_EPSIZE, 1); ConfigSuccess &= Endpoint_ConfigureEndpoint((CDC_IN_EPNUM | ENDPOINT_DIR_IN), EP_TYPE_BULK, CDC_EPSIZE, 1); #endif + #ifdef JOYSTICK_ENABLE - ConfigSuccess &= ENDPOINT_CONFIG(JOYSTICK_IN_EPNUM, EP_TYPE_INTERRUPT, ENDPOINT_DIR_IN, JOYSTICK_EPSIZE, ENDPOINT_BANK_SINGLE); + /* Setup joystick endpoint */ + ConfigSuccess &= Endpoint_ConfigureEndpoint((JOYSTICK_IN_EPNUM | ENDPOINT_DIR_IN), EP_TYPE_INTERRUPT, JOYSTICK_EPSIZE, 1); #endif } -- cgit v1.2.3 From 0f596881b36587a298568192078f9b467c51c109 Mon Sep 17 00:00:00 2001 From: Ryan Date: Tue, 25 Aug 2020 19:03:45 +1000 Subject: Remove support for Adafruit EZ-Key (#10103) * Remove support for Adafruit EZ-Key * Update docs/ja/feature_bluetooth.md Co-authored-by: Takeshi ISHII <2170248+mtei@users.noreply.github.com> Co-authored-by: Takeshi ISHII <2170248+mtei@users.noreply.github.com> --- tmk_core/protocol/lufa/lufa.c | 105 +++++++++++++++++++++++++----------------- 1 file changed, 62 insertions(+), 43 deletions(-) (limited to 'tmk_core/protocol/lufa/lufa.c') diff --git a/tmk_core/protocol/lufa/lufa.c b/tmk_core/protocol/lufa/lufa.c index 8410eb483f..09ba0bacf7 100644 --- a/tmk_core/protocol/lufa/lufa.c +++ b/tmk_core/protocol/lufa/lufa.c @@ -69,7 +69,7 @@ extern keymap_config_t keymap_config; # ifdef MODULE_ADAFRUIT_BLE # include "adafruit_ble.h" # else -# include "bluetooth.h" +# include "../serial.h" # endif #endif @@ -89,6 +89,46 @@ extern keymap_config_t keymap_config; # include "joystick.h" #endif +// https://cdn.sparkfun.com/datasheets/Wireless/Bluetooth/bluetooth_cr_UG-v1.0r.pdf#G7.663734 +static inline uint16_t CONSUMER2RN42(uint16_t usage) { + switch (usage) { + case AC_HOME: + return 0x0001; + case AL_EMAIL: + return 0x0002; + case AC_SEARCH: + return 0x0004; + case AL_KEYBOARD_LAYOUT: + return 0x0008; + case AUDIO_VOL_UP: + return 0x0010; + case AUDIO_VOL_DOWN: + return 0x0020; + case AUDIO_MUTE: + return 0x0040; + case TRANSPORT_PLAY_PAUSE: + return 0x0080; + case TRANSPORT_NEXT_TRACK: + return 0x0100; + case TRANSPORT_PREV_TRACK: + return 0x0200; + case TRANSPORT_STOP: + return 0x0400; + case TRANSPORT_EJECT: + return 0x0800; + case TRANSPORT_FAST_FORWARD: + return 0x1000; + case TRANSPORT_REWIND: + return 0x2000; + case TRANSPORT_STOP_EJECT: + return 0x4000; + case AL_LOCAL_BROWSER: + return 0x8000; + default: + return 0; + } +} + uint8_t keyboard_idle = 0; /* 0: Boot Protocol, 1: Report Protocol(default) */ uint8_t keyboard_protocol = 1; @@ -631,20 +671,13 @@ static void send_keyboard(report_keyboard_t *report) { # ifdef MODULE_ADAFRUIT_BLE adafruit_ble_send_keys(report->mods, report->keys, sizeof(report->keys)); # elif MODULE_RN42 - bluefruit_serial_send(0xFD); - bluefruit_serial_send(0x09); - bluefruit_serial_send(0x01); - bluefruit_serial_send(report->mods); - bluefruit_serial_send(report->reserved); - for (uint8_t i = 0; i < KEYBOARD_REPORT_KEYS; i++) { - bluefruit_serial_send(report->keys[i]); - } -# else - bluefruit_serial_send(0xFD); - bluefruit_serial_send(report->mods); - bluefruit_serial_send(report->reserved); + serial_send(0xFD); + serial_send(0x09); + serial_send(0x01); + serial_send(report->mods); + serial_send(report->reserved); for (uint8_t i = 0; i < KEYBOARD_REPORT_KEYS; i++) { - bluefruit_serial_send(report->keys[i]); + serial_send(report->keys[i]); } # endif } @@ -697,15 +730,15 @@ static void send_mouse(report_mouse_t *report) { // FIXME: mouse buttons adafruit_ble_send_mouse_move(report->x, report->y, report->v, report->h, report->buttons); # else - bluefruit_serial_send(0xFD); - bluefruit_serial_send(0x00); - bluefruit_serial_send(0x03); - bluefruit_serial_send(report->buttons); - bluefruit_serial_send(report->x); - bluefruit_serial_send(report->y); - bluefruit_serial_send(report->v); // should try sending the wheel v here - bluefruit_serial_send(report->h); // should try sending the wheel h here - bluefruit_serial_send(0x00); + serial_send(0xFD); + serial_send(0x00); + serial_send(0x03); + serial_send(report->buttons); + serial_send(report->x); + serial_send(report->y); + serial_send(report->v); // should try sending the wheel v here + serial_send(report->h); // should try sending the wheel h here + serial_send(0x00); # endif } @@ -778,25 +811,11 @@ static void send_consumer(uint16_t data) { if (data == last_data) return; last_data = data; uint16_t bitmap = CONSUMER2RN42(data); - bluefruit_serial_send(0xFD); - bluefruit_serial_send(0x03); - bluefruit_serial_send(0x03); - bluefruit_serial_send(bitmap & 0xFF); - bluefruit_serial_send((bitmap >> 8) & 0xFF); -# else - static uint16_t last_data = 0; - if (data == last_data) return; - last_data = data; - uint16_t bitmap = CONSUMER2BLUEFRUIT(data); - bluefruit_serial_send(0xFD); - bluefruit_serial_send(0x00); - bluefruit_serial_send(0x02); - bluefruit_serial_send(bitmap & 0xFF); - bluefruit_serial_send((bitmap >> 8) & 0xFF); - bluefruit_serial_send(0x00); - bluefruit_serial_send(0x00); - bluefruit_serial_send(0x00); - bluefruit_serial_send(0x00); + serial_send(0xFD); + serial_send(0x03); + serial_send(0x03); + serial_send(bitmap & 0xFF); + serial_send((bitmap >> 8) & 0xFF); # endif } @@ -1018,7 +1037,7 @@ int main(void) { setup_usb(); sei(); -#if defined(MODULE_ADAFRUIT_EZKEY) || defined(MODULE_RN42) +#if defined(MODULE_RN42) serial_init(); #endif -- cgit v1.2.3 From a3db72df7299140e52f57d082a3742a8b480a226 Mon Sep 17 00:00:00 2001 From: QMK Bot Date: Sat, 29 Aug 2020 22:57:48 +0000 Subject: format code according to conventions [skip ci] --- tmk_core/protocol/lufa/lufa.c | 28 ++++++++++++++++------------ 1 file changed, 16 insertions(+), 12 deletions(-) (limited to 'tmk_core/protocol/lufa/lufa.c') diff --git a/tmk_core/protocol/lufa/lufa.c b/tmk_core/protocol/lufa/lufa.c index 09ba0bacf7..cec0044026 100644 --- a/tmk_core/protocol/lufa/lufa.c +++ b/tmk_core/protocol/lufa/lufa.c @@ -316,39 +316,43 @@ void send_joystick_packet(joystick_t *joystick) { joystick_report_t r = { # if JOYSTICK_AXES_COUNT > 0 - .axes = {joystick->axes[0], + .axes = + { + joystick->axes[0], # if JOYSTICK_AXES_COUNT >= 2 - joystick->axes[1], + joystick->axes[1], # endif # if JOYSTICK_AXES_COUNT >= 3 - joystick->axes[2], + joystick->axes[2], # endif # if JOYSTICK_AXES_COUNT >= 4 - joystick->axes[3], + joystick->axes[3], # endif # if JOYSTICK_AXES_COUNT >= 5 - joystick->axes[4], + joystick->axes[4], # endif # if JOYSTICK_AXES_COUNT >= 6 - joystick->axes[5], + joystick->axes[5], # endif - }, + }, # endif // JOYSTICK_AXES_COUNT>0 # if JOYSTICK_BUTTON_COUNT > 0 - .buttons = {joystick->buttons[0], + .buttons = + { + joystick->buttons[0], # if JOYSTICK_BUTTON_COUNT > 8 - joystick->buttons[1], + joystick->buttons[1], # endif # if JOYSTICK_BUTTON_COUNT > 16 - joystick->buttons[2], + joystick->buttons[2], # endif # if JOYSTICK_BUTTON_COUNT > 24 - joystick->buttons[3], + joystick->buttons[3], # endif - } + } # endif // JOYSTICK_BUTTON_COUNT>0 }; -- cgit v1.2.3