From feb5e4aaebb78842c090230f68ea9de80a5c17e6 Mon Sep 17 00:00:00 2001 From: MakotoKurauchi Date: Sat, 11 Aug 2018 00:22:09 +0900 Subject: Keyboard: Helix serial improvements (#3608) * add change_reciver2sender()/change_sender2reciver() This is a change to improve readability. * txled, rxled off in matrix_init() * add serial_send_packet() / serial_recive_packet() This is a change to reduce object size. * add serial_low() at ISR() top * add __attribute__((always_inline)) to some functions * modify serial_send_packet()/serial_recive_packet() A little, object size reduction. A little, speedup. * add debug code to helix/serial.c * Adjust sampling timing of serial signal being received * add split_scomm.c/split_scomm.h and change serial.c/serial.h serial.c was divided into 2 layers, split_scom.c and serial.c. The upper layer split_scomm.c is called from matrix.c. The lower layer serial.c accesses the hardware. * add split_scomm.c/split_scomm.h into helix/rev1 * reduce object size helix/rev2/matrix.c * remove checksum check, add parity check * force occur parity error for test * parity test ok. remove test code * change some comment & add skip code when buffer_size == 0 * serial.c: multiple types of transaction support Add 4 bits transaction-type field at packet top. Select Transaction Descriptor Table entry by transaction-type. * helix serial master-slave transaction optimize Using multi-type transaction feature of serial.c, communication contents between master slaves were optimized. * add debug code for retry * add comment into each config.h * fix ISR status drop * add a debug macro 'debug_retry_chg()' * reduce led_test size * remove debug code from helix/serial.c and etc. * helix:five_rows change TAPPING_TERM value 140 * Improved compatibility with let's split of serial.c. Finish helix/serial.c improvement. - The difference with the original let's split's serial.c - It's high-speed about 4 times. - Stable bi-directional data transfer. (Helix need master to slave transfer) - serial.h was divided 2 files, serial_config.h and sereial.h - With multiple types of transaction support, communication contents can be optimized. (NEW flexible API) - USE OLD Simple APIs (compatible with let's split serial.c) - files : - serial_config.h -- hardware configuration (need include by config.h) - serial.c/serial.h -- serial communication - USE NEW flexible APIs. (Support multi-type transaction function.) serial.c was divided into 2 layers, split_scom.c and serial.c. The upper layer split_scomm.c is called from matrix.c. The lower layer serial.c accesses the hardware. - files - split_scomm.c -- communication buffer is defined in here. call by matrix.c. - split_scomm.h -- buffer size is defined in here. include by matrix.c, split_util.c - serial_config.h -- hardware configuration (need include by config.h) To use the NEW API, specify #define SERIAL_USE_MULTI_TRANSACTION - serial.c/serial.h -- serial communication lower layer - NEW APIs for serial.c / serial.h (The lower layer) // Soft Serial Transaction Descriptor typedef struct _SSTD_t { uint8_t *status; uint8_t initiator2target_buffer_size; uint8_t *initiator2target_buffer; uint8_t target2initiator_buffer_size; uint8_t *target2initiator_buffer; } SSTD_t; // initiator is transaction start side void soft_serial_initiator_init(SSTD_t *sstd_table); // target is interrupt accept side void soft_serial_target_init(SSTD_t *sstd_table); int soft_serial_transaction(int sstd_index); int soft_serial_get_and_clean_target_status(int sstd_index); - NEW APIs for split_scomm.c / split_scomm.h (The upper layer) move from old serial.c the following buffer and functions serial_slave_buffer[] serial_master_buffer[] void serial_master_init(void) void serial_slave_init(void) int serial_update_buffers(void) define SERIAL_xxxxx_BUFFER_LENGTH move from serial_config.h to split_scomm.h --- .../helix/rev1/keymaps/OLED_sample/serial_config.h | 2 +- keyboards/helix/rev1/rules.mk | 4 +- keyboards/helix/rev1/serial_config.h | 2 +- keyboards/helix/rev2/keymaps/default/config.h | 3 + keyboards/helix/rev2/keymaps/edvorakjp/config.h | 3 + keyboards/helix/rev2/keymaps/five_rows/config.h | 6 + .../helix/rev2/keymaps/five_rows_jis/config.h | 3 + keyboards/helix/rev2/keymaps/froggy/config.h | 3 + keyboards/helix/rev2/keymaps/led_test/config.h | 3 + keyboards/helix/rev2/matrix.c | 58 +-- keyboards/helix/rev2/rules.mk | 7 +- keyboards/helix/rev2/serial_config.h | 3 +- keyboards/helix/rev2/serial_config_simpleapi.h | 8 + keyboards/helix/rev2/split_scomm.c | 73 ++++ keyboards/helix/rev2/split_scomm.h | 24 ++ keyboards/helix/rev2/split_util.c | 2 +- keyboards/helix/rules.mk | 9 +- keyboards/helix/serial.c | 411 ++++++++++++++------- keyboards/helix/serial.h | 63 +++- 19 files changed, 514 insertions(+), 173 deletions(-) create mode 100644 keyboards/helix/rev2/serial_config_simpleapi.h create mode 100644 keyboards/helix/rev2/split_scomm.c create mode 100644 keyboards/helix/rev2/split_scomm.h (limited to 'keyboards/helix') diff --git a/keyboards/helix/rev1/keymaps/OLED_sample/serial_config.h b/keyboards/helix/rev1/keymaps/OLED_sample/serial_config.h index be2e7cb8b1..b991b874b7 100644 --- a/keyboards/helix/rev1/keymaps/OLED_sample/serial_config.h +++ b/keyboards/helix/rev1/keymaps/OLED_sample/serial_config.h @@ -9,7 +9,7 @@ #define SERIAL_PIN_INTERRUPT INT2_vect #define SERIAL_SLAVE_BUFFER_LENGTH MATRIX_ROWS/2 -#define SERIAL_MASTER_BUFFER_LENGTH 1 +#define SERIAL_MASTER_BUFFER_LENGTH 0 //// #error rev1/keymaps/OLED_sample serial config diff --git a/keyboards/helix/rev1/rules.mk b/keyboards/helix/rev1/rules.mk index daba80eaea..13834f5da1 100644 --- a/keyboards/helix/rev1/rules.mk +++ b/keyboards/helix/rev1/rules.mk @@ -1,4 +1,4 @@ -SRC += rev1/matrix.c \ - rev1/split_util.c +SRC += rev1/matrix.c +SRC += rev1/split_util.c BACKLIGHT_ENABLE = no diff --git a/keyboards/helix/rev1/serial_config.h b/keyboards/helix/rev1/serial_config.h index 2b668a6afc..51c6aa3750 100644 --- a/keyboards/helix/rev1/serial_config.h +++ b/keyboards/helix/rev1/serial_config.h @@ -9,7 +9,7 @@ #define SERIAL_PIN_INTERRUPT INT0_vect #define SERIAL_SLAVE_BUFFER_LENGTH MATRIX_ROWS/2 -#define SERIAL_MASTER_BUFFER_LENGTH 1 +#define SERIAL_MASTER_BUFFER_LENGTH 0 /// #error rev1 serial config diff --git a/keyboards/helix/rev2/keymaps/default/config.h b/keyboards/helix/rev2/keymaps/default/config.h index 6da6849a1d..185e678385 100644 --- a/keyboards/helix/rev2/keymaps/default/config.h +++ b/keyboards/helix/rev2/keymaps/default/config.h @@ -21,6 +21,9 @@ along with this program. If not, see . #ifndef CONFIG_USER_H #define CONFIG_USER_H +// if you need more program area, try uncomment follow line +//#include "serial_config_simpleapi.h" + // place overrides here #endif /* CONFIG_USER_H */ diff --git a/keyboards/helix/rev2/keymaps/edvorakjp/config.h b/keyboards/helix/rev2/keymaps/edvorakjp/config.h index a7a5f83600..ead31605b2 100644 --- a/keyboards/helix/rev2/keymaps/edvorakjp/config.h +++ b/keyboards/helix/rev2/keymaps/edvorakjp/config.h @@ -1,6 +1,9 @@ #ifndef CONFIG_USER_H #define CONFIG_USER_H +// if you need more program area, try uncomment follow line +//#include "serial_config_simpleapi.h" + #undef TAPPING_FORCE_HOLD #undef TAPPING_TERM #define TAPPING_TERM 120 diff --git a/keyboards/helix/rev2/keymaps/five_rows/config.h b/keyboards/helix/rev2/keymaps/five_rows/config.h index 6da6849a1d..8372194604 100644 --- a/keyboards/helix/rev2/keymaps/five_rows/config.h +++ b/keyboards/helix/rev2/keymaps/five_rows/config.h @@ -21,6 +21,12 @@ along with this program. If not, see . #ifndef CONFIG_USER_H #define CONFIG_USER_H +// if you need more program area, try uncomment follow line +//#include "serial_config_simpleapi.h" + +#undef TAPPING_TERM +#define TAPPING_TERM 140 + // place overrides here #endif /* CONFIG_USER_H */ diff --git a/keyboards/helix/rev2/keymaps/five_rows_jis/config.h b/keyboards/helix/rev2/keymaps/five_rows_jis/config.h index 34650b99a6..c380b7db4e 100644 --- a/keyboards/helix/rev2/keymaps/five_rows_jis/config.h +++ b/keyboards/helix/rev2/keymaps/five_rows_jis/config.h @@ -23,6 +23,9 @@ along with this program. If not, see . // place overrides here +// if you need more program area, try uncomment follow line +//#include "serial_config_simpleapi.h" + #ifdef MOUSEKEY_ENABLE #undef MOUSEKEY_INTERVAL #define MOUSEKEY_INTERVAL 0 diff --git a/keyboards/helix/rev2/keymaps/froggy/config.h b/keyboards/helix/rev2/keymaps/froggy/config.h index df72aef123..dad2483034 100644 --- a/keyboards/helix/rev2/keymaps/froggy/config.h +++ b/keyboards/helix/rev2/keymaps/froggy/config.h @@ -21,6 +21,9 @@ along with this program. If not, see . #ifndef CONFIG_USER_H #define CONFIG_USER_H +// if you need more program area, try uncomment follow line +//#include "serial_config_simpleapi.h" + #undef TAPPING_TERM #define TAPPING_TERM 200 #define ONESHOT_TAP_TOGGLE 5 /* Tapping this number of times holds the key until tapped this number of times again. */ diff --git a/keyboards/helix/rev2/keymaps/led_test/config.h b/keyboards/helix/rev2/keymaps/led_test/config.h index 6da6849a1d..0438254528 100644 --- a/keyboards/helix/rev2/keymaps/led_test/config.h +++ b/keyboards/helix/rev2/keymaps/led_test/config.h @@ -21,6 +21,9 @@ along with this program. If not, see . #ifndef CONFIG_USER_H #define CONFIG_USER_H +// if you need more program area, try uncomment follow line +#include "serial_config_simpleapi.h" + // place overrides here #endif /* CONFIG_USER_H */ diff --git a/keyboards/helix/rev2/matrix.c b/keyboards/helix/rev2/matrix.c index 8a1ce3af1e..322959dbbb 100644 --- a/keyboards/helix/rev2/matrix.c +++ b/keyboards/helix/rev2/matrix.c @@ -20,6 +20,7 @@ along with this program. If not, see . */ #include #include +#include #include #include #include @@ -34,7 +35,7 @@ along with this program. If not, see . #ifdef USE_MATRIX_I2C # include "i2c.h" #else // USE_SERIAL -# include "serial.h" +# include "split_scomm.h" #endif #ifndef DEBOUNCE @@ -102,6 +103,8 @@ void matrix_init(void) init_cols(); TX_RX_LED_INIT; + TXLED0; + RXLED0; // initialize matrix state: all keys off for (uint8_t i=0; i < MATRIX_ROWS; i++) { @@ -178,17 +181,20 @@ i2c_error: // the cable is disconnceted, or something else went wrong #else // USE_SERIAL -int serial_transaction(void) { +int serial_transaction(int master_changed) { int slaveOffset = (isLeftHand) ? (ROWS_PER_HAND) : 0; +#ifdef SERIAL_USE_MULTI_TRANSACTION + int ret=serial_update_buffers(master_changed); +#else int ret=serial_update_buffers(); +#endif if (ret ) { - if(ret==2)RXLED1; + if(ret==2) RXLED1; return 1; } -RXLED0; - for (int i = 0; i < ROWS_PER_HAND; ++i) { - matrix[slaveOffset+i] = serial_slave_buffer[i]; - } + RXLED0; + memcpy(&matrix[slaveOffset], + (void *)serial_slave_buffer, sizeof(serial_slave_buffer)); return 0; } #endif @@ -199,19 +205,9 @@ uint8_t matrix_scan(void) matrix_master_scan(); }else{ matrix_slave_scan(); - -// if(serial_slave_DATA_CORRUPT()){ -// TXLED0; - int offset = (isLeftHand) ? ROWS_PER_HAND : 0; - - for (int i = 0; i < ROWS_PER_HAND; ++i) { - matrix[offset+i] = serial_master_buffer[i]; - } - -// }else{ -// TXLED1; -// } - + int offset = (isLeftHand) ? ROWS_PER_HAND : 0; + memcpy(&matrix[offset], + (void *)serial_master_buffer, sizeof(serial_master_buffer)); matrix_scan_quantum(); } return 1; @@ -221,6 +217,7 @@ uint8_t matrix_scan(void) uint8_t matrix_master_scan(void) { int ret = _matrix_scan(); + int mchanged = 1; #ifndef KEYBOARD_helix_rev1 int offset = (isLeftHand) ? 0 : ROWS_PER_HAND; @@ -231,16 +228,19 @@ uint8_t matrix_master_scan(void) { // i2c_slave_buffer[i] = matrix[offset+i]; // } #else // USE_SERIAL - for (int i = 0; i < ROWS_PER_HAND; ++i) { - serial_master_buffer[i] = matrix[offset+i]; - } + #ifdef SERIAL_USE_MULTI_TRANSACTION + mchanged = memcmp((void *)serial_master_buffer, + &matrix[offset], sizeof(serial_master_buffer)); + #endif + memcpy((void *)serial_master_buffer, + &matrix[offset], sizeof(serial_master_buffer)); #endif #endif #ifdef USE_MATRIX_I2C if( i2c_transaction() ) { #else // USE_SERIAL - if( serial_transaction() ) { + if( serial_transaction(mchanged) ) { #endif // turn on the indicator led when halves are disconnected TXLED1; @@ -274,9 +274,19 @@ void matrix_slave_scan(void) { i2c_slave_buffer[i] = matrix[offset+i]; } #else // USE_SERIAL + #ifdef SERIAL_USE_MULTI_TRANSACTION + int change = 0; + #endif for (int i = 0; i < ROWS_PER_HAND; ++i) { + #ifdef SERIAL_USE_MULTI_TRANSACTION + if( serial_slave_buffer[i] != matrix[offset+i] ) + change = 1; + #endif serial_slave_buffer[i] = matrix[offset+i]; } + #ifdef SERIAL_USE_MULTI_TRANSACTION + slave_buffer_change_count += change; + #endif #endif } diff --git a/keyboards/helix/rev2/rules.mk b/keyboards/helix/rev2/rules.mk index 6ab01f44b4..4ea623c436 100644 --- a/keyboards/helix/rev2/rules.mk +++ b/keyboards/helix/rev2/rules.mk @@ -1,3 +1,4 @@ -SRC += rev2/matrix.c \ - rev2/split_util.c \ - ws2812.c +SRC += rev2/matrix.c +SRC += rev2/split_util.c +SRC += rev2/split_scomm.c +SRC += ws2812.c diff --git a/keyboards/helix/rev2/serial_config.h b/keyboards/helix/rev2/serial_config.h index 82c6e4e836..8d7e628378 100644 --- a/keyboards/helix/rev2/serial_config.h +++ b/keyboards/helix/rev2/serial_config.h @@ -8,8 +8,7 @@ #define SERIAL_PIN_MASK _BV(PD2) #define SERIAL_PIN_INTERRUPT INT2_vect -#define SERIAL_SLAVE_BUFFER_LENGTH MATRIX_ROWS/2 -#define SERIAL_MASTER_BUFFER_LENGTH MATRIX_ROWS/2 +#define SERIAL_USE_MULTI_TRANSACTION //// #error rev2 serial config diff --git a/keyboards/helix/rev2/serial_config_simpleapi.h b/keyboards/helix/rev2/serial_config_simpleapi.h new file mode 100644 index 0000000000..e2d22a41e7 --- /dev/null +++ b/keyboards/helix/rev2/serial_config_simpleapi.h @@ -0,0 +1,8 @@ +#ifndef SERIAL_CONFIG_SIMPLEAPI_H +#define SERIAL_CONFIG_SIMPLEAPI_H + +#undef SERIAL_USE_MULTI_TRANSACTION +#define SERIAL_SLAVE_BUFFER_LENGTH MATRIX_ROWS/2 +#define SERIAL_MASTER_BUFFER_LENGTH MATRIX_ROWS/2 + +#endif // SERIAL_CONFIG_SIMPLEAPI_H diff --git a/keyboards/helix/rev2/split_scomm.c b/keyboards/helix/rev2/split_scomm.c new file mode 100644 index 0000000000..9719eb22ea --- /dev/null +++ b/keyboards/helix/rev2/split_scomm.c @@ -0,0 +1,73 @@ +#ifdef USE_SERIAL +#ifdef SERIAL_USE_MULTI_TRANSACTION +/* --- USE flexible API (using multi-type transaction function) --- */ + +#include +#include +#include +#include +#include "serial.h" +#ifdef SERIAL_DEBUG_MODE +#include +#endif + +uint8_t volatile serial_slave_buffer[SERIAL_SLAVE_BUFFER_LENGTH] = {0}; +uint8_t volatile serial_master_buffer[SERIAL_MASTER_BUFFER_LENGTH] = {0}; +uint8_t volatile status_com = 0; +uint8_t volatile status1 = 0; +uint8_t slave_buffer_change_count = 0; +uint8_t s_change_old = 0xff; + +SSTD_t transactions[] = { +#define GET_SLAVE_STATUS 0 + /* master buffer not changed, only recive slave_buffer_change_count */ + { (uint8_t *)&status_com, + 0, NULL, + sizeof(slave_buffer_change_count), &slave_buffer_change_count, + }, +#define PUT_MASTER_GET_SLAVE_STATUS 1 + /* master buffer changed need send, and recive slave_buffer_change_count */ + { (uint8_t *)&status_com, + sizeof(serial_master_buffer), (uint8_t *)serial_master_buffer, + sizeof(slave_buffer_change_count), &slave_buffer_change_count, + }, +#define GET_SLAVE_BUFFER 2 + /* recive serial_slave_buffer */ + { (uint8_t *)&status1, + 0, NULL, + sizeof(serial_slave_buffer), (uint8_t *)serial_slave_buffer + } +}; + +void serial_master_init(void) +{ + soft_serial_initiator_init(transactions); +} + +void serial_slave_init(void) +{ + soft_serial_target_init(transactions); +} + +// 0 => no error +// 1 => slave did not respond +// 2 => checksum error +int serial_update_buffers(int master_update) +{ + int status; + static int need_retry = 0; + if( s_change_old != slave_buffer_change_count ) { + status = soft_serial_transaction(GET_SLAVE_BUFFER); + if( status == TRANSACTION_END ) + s_change_old = slave_buffer_change_count; + } + if( !master_update && !need_retry) + status = soft_serial_transaction(GET_SLAVE_STATUS); + else + status = soft_serial_transaction(PUT_MASTER_GET_SLAVE_STATUS); + need_retry = ( status == TRANSACTION_END ) ? 0 : 1; + return status; +} + +#endif // SERIAL_USE_MULTI_TRANSACTION +#endif /* USE_SERIAL */ diff --git a/keyboards/helix/rev2/split_scomm.h b/keyboards/helix/rev2/split_scomm.h new file mode 100644 index 0000000000..873d8939d8 --- /dev/null +++ b/keyboards/helix/rev2/split_scomm.h @@ -0,0 +1,24 @@ +#ifndef SPLIT_COMM_H +#define SPLIT_COMM_H + +#ifndef SERIAL_USE_MULTI_TRANSACTION +/* --- USE Simple API (OLD API, compatible with let's split serial.c) --- */ +#include "serial.h" + +#else +/* --- USE flexible API (using multi-type transaction function) --- */ +// Buffers for master - slave communication +#define SERIAL_SLAVE_BUFFER_LENGTH MATRIX_ROWS/2 +#define SERIAL_MASTER_BUFFER_LENGTH MATRIX_ROWS/2 + +extern volatile uint8_t serial_slave_buffer[SERIAL_SLAVE_BUFFER_LENGTH]; +extern volatile uint8_t serial_master_buffer[SERIAL_MASTER_BUFFER_LENGTH]; +extern uint8_t slave_buffer_change_count; + +void serial_master_init(void); +void serial_slave_init(void); +int serial_update_buffers(int master_changed); + +#endif + +#endif /* SPLIT_COMM_H */ diff --git a/keyboards/helix/rev2/split_util.c b/keyboards/helix/rev2/split_util.c index beb39fa005..e1ff8b4379 100644 --- a/keyboards/helix/rev2/split_util.c +++ b/keyboards/helix/rev2/split_util.c @@ -11,7 +11,7 @@ #ifdef USE_MATRIX_I2C # include "i2c.h" #else -# include "serial.h" +# include "split_scomm.h" #endif volatile bool isLeftHand = true; diff --git a/keyboards/helix/rules.mk b/keyboards/helix/rules.mk index c35f93fb07..e42f92cf8a 100644 --- a/keyboards/helix/rules.mk +++ b/keyboards/helix/rules.mk @@ -1,6 +1,9 @@ -SRC += i2c.c \ - serial.c \ - ssd1306.c +SRC += i2c.c +SRC += serial.c +SRC += ssd1306.c + +# if firmware size over limit, try this option +# CFLAGS += -flto # MCU name #MCU = at90usb1287 diff --git a/keyboards/helix/serial.c b/keyboards/helix/serial.c index 5919415877..11ceff0b37 100644 --- a/keyboards/helix/serial.c +++ b/keyboards/helix/serial.c @@ -9,40 +9,85 @@ #include #include #include +#include #include #include "serial.h" +//#include #ifdef USE_SERIAL +#ifndef SERIAL_USE_MULTI_TRANSACTION +/* --- USE Simple API (OLD API, compatible with let's split serial.c) */ + #if SERIAL_SLAVE_BUFFER_LENGTH > 0 + uint8_t volatile serial_slave_buffer[SERIAL_SLAVE_BUFFER_LENGTH] = {0}; + #endif + #if SERIAL_MASTER_BUFFER_LENGTH > 0 + uint8_t volatile serial_master_buffer[SERIAL_MASTER_BUFFER_LENGTH] = {0}; + #endif + uint8_t volatile status0 = 0; + +SSTD_t transactions[] = { + { (uint8_t *)&status0, + #if SERIAL_MASTER_BUFFER_LENGTH > 0 + sizeof(serial_master_buffer), (uint8_t *)serial_master_buffer, + #else + 0, (uint8_t *)NULL, + #endif + #if SERIAL_SLAVE_BUFFER_LENGTH > 0 + sizeof(serial_slave_buffer), (uint8_t *)serial_slave_buffer + #else + 0, (uint8_t *)NULL, + #endif + } +}; + +void serial_master_init(void) +{ soft_serial_initiator_init(transactions); } + +void serial_slave_init(void) +{ soft_serial_target_init(transactions); } + +// 0 => no error +// 1 => slave did not respond +// 2 => checksum error +int serial_update_buffers() +{ return soft_serial_transaction(); } + +#endif // Simple API (OLD API, compatible with let's split serial.c) + +#define ALWAYS_INLINE __attribute__((always_inline)) +#define NO_INLINE __attribute__((noinline)) #define _delay_sub_us(x) __builtin_avr_delay_cycles(x) // Serial pulse period in microseconds. +#define TID_SEND_ADJUST 14 + #define SELECT_SERIAL_SPEED 1 #if SELECT_SERIAL_SPEED == 0 // Very High speed #define SERIAL_DELAY 4 // micro sec - #define READ_WRITE_START_ADJUST 30 // cycles - #define READ_WRITE_WIDTH_ADJUST 10 // cycles + #define READ_WRITE_START_ADJUST 33 // cycles + #define READ_WRITE_WIDTH_ADJUST 3 // cycles #elif SELECT_SERIAL_SPEED == 1 // High speed #define SERIAL_DELAY 6 // micro sec - #define READ_WRITE_START_ADJUST 23 // cycles - #define READ_WRITE_WIDTH_ADJUST 10 // cycles + #define READ_WRITE_START_ADJUST 30 // cycles + #define READ_WRITE_WIDTH_ADJUST 3 // cycles #elif SELECT_SERIAL_SPEED == 2 // Middle speed #define SERIAL_DELAY 12 // micro sec - #define READ_WRITE_START_ADJUST 25 // cycles - #define READ_WRITE_WIDTH_ADJUST 10 // cycles + #define READ_WRITE_START_ADJUST 30 // cycles + #define READ_WRITE_WIDTH_ADJUST 3 // cycles #elif SELECT_SERIAL_SPEED == 3 // Low speed #define SERIAL_DELAY 24 // micro sec - #define READ_WRITE_START_ADJUST 25 // cycles - #define READ_WRITE_WIDTH_ADJUST 10 // cycles + #define READ_WRITE_START_ADJUST 30 // cycles + #define READ_WRITE_WIDTH_ADJUST 3 // cycles #elif SELECT_SERIAL_SPEED == 4 // Very Low speed #define SERIAL_DELAY 50 // micro sec - #define READ_WRITE_START_ADJUST 25 // cycles - #define READ_WRITE_WIDTH_ADJUST 10 // cycles + #define READ_WRITE_START_ADJUST 30 // cycles + #define READ_WRITE_WIDTH_ADJUST 3 // cycles #else #error Illegal Serial Speed #endif @@ -51,14 +96,15 @@ #define SERIAL_DELAY_HALF1 (SERIAL_DELAY/2) #define SERIAL_DELAY_HALF2 (SERIAL_DELAY - SERIAL_DELAY/2) -#define SLAVE_INT_WIDTH 1 -#define SLAVE_INT_RESPONSE_TIME SERIAL_DELAY - -uint8_t volatile serial_slave_buffer[SERIAL_SLAVE_BUFFER_LENGTH] = {0}; -uint8_t volatile serial_master_buffer[SERIAL_MASTER_BUFFER_LENGTH] = {0}; +#define SLAVE_INT_WIDTH_US 1 +#ifndef SERIAL_USE_MULTI_TRANSACTION + #define SLAVE_INT_RESPONSE_TIME SERIAL_DELAY +#else + #define SLAVE_INT_ACK_WIDTH_UNIT 2 + #define SLAVE_INT_ACK_WIDTH 4 +#endif -#define SLAVE_DATA_CORRUPT (1<<0) -volatile uint8_t status = 0; +static SSTD_t *Transaction_table = NULL; inline static void serial_delay(void) { @@ -75,12 +121,14 @@ void serial_delay_half2(void) { _delay_us(SERIAL_DELAY_HALF2); } +inline static void serial_output(void) ALWAYS_INLINE; inline static void serial_output(void) { SERIAL_PIN_DDR |= SERIAL_PIN_MASK; } // make the serial pin an input with pull-up resistor +inline static void serial_input_with_pullup(void) ALWAYS_INLINE; inline static void serial_input_with_pullup(void) { SERIAL_PIN_DDR &= ~SERIAL_PIN_MASK; @@ -92,50 +140,58 @@ uint8_t serial_read_pin(void) { return !!(SERIAL_PIN_INPUT & SERIAL_PIN_MASK); } +inline static void serial_low(void) ALWAYS_INLINE; inline static void serial_low(void) { SERIAL_PIN_PORT &= ~SERIAL_PIN_MASK; } +inline static void serial_high(void) ALWAYS_INLINE; inline static void serial_high(void) { SERIAL_PIN_PORT |= SERIAL_PIN_MASK; } -void serial_master_init(void) { - serial_output(); - serial_high(); +void soft_serial_initiator_init(SSTD_t *sstd_table) +{ + Transaction_table = sstd_table; + serial_output(); + serial_high(); } -void serial_slave_init(void) { - serial_input_with_pullup(); +void soft_serial_target_init(SSTD_t *sstd_table) +{ + Transaction_table = sstd_table; + serial_input_with_pullup(); #if SERIAL_PIN_MASK == _BV(PD0) - // Enable INT0 - EIMSK |= _BV(INT0); - // Trigger on falling edge of INT0 - EICRA &= ~(_BV(ISC00) | _BV(ISC01)); + // Enable INT0 + EIMSK |= _BV(INT0); + // Trigger on falling edge of INT0 + EICRA &= ~(_BV(ISC00) | _BV(ISC01)); #elif SERIAL_PIN_MASK == _BV(PD2) - // Enable INT2 - EIMSK |= _BV(INT2); - // Trigger on falling edge of INT2 - EICRA &= ~(_BV(ISC20) | _BV(ISC21)); + // Enable INT2 + EIMSK |= _BV(INT2); + // Trigger on falling edge of INT2 + EICRA &= ~(_BV(ISC20) | _BV(ISC21)); #else #error unknown SERIAL_PIN_MASK value #endif } // Used by the sender to synchronize timing with the reciver. +static void sync_recv(void) NO_INLINE; static void sync_recv(void) { - for (int i = 0; i < SERIAL_DELAY*5 && serial_read_pin(); i++ ) { + for (uint8_t i = 0; i < SERIAL_DELAY*5 && serial_read_pin(); i++ ) { } - // This shouldn't hang if the slave disconnects because the - // serial line will float to high if the slave does disconnect. + // This shouldn't hang if the target disconnects because the + // serial line will float to high if the target does disconnect. while (!serial_read_pin()); } // Used by the reciver to send a synchronization signal to the sender. +static void sync_send(void)NO_INLINE; static void sync_send(void) { serial_low(); @@ -144,152 +200,245 @@ void sync_send(void) { } // Reads a byte from the serial line -static -uint8_t serial_read_byte(void) { - uint8_t byte = 0; +static uint8_t serial_read_chunk(uint8_t *pterrcount, uint8_t bit) NO_INLINE; +static uint8_t serial_read_chunk(uint8_t *pterrcount, uint8_t bit) { + uint8_t byte, i, p, pb; + _delay_sub_us(READ_WRITE_START_ADJUST); - for ( uint8_t i = 0; i < 8; ++i) { - serial_delay_half1(); // read the middle of pulses - byte = (byte << 1) | serial_read_pin(); - _delay_sub_us(READ_WRITE_WIDTH_ADJUST); - serial_delay_half2(); + for( i = 0, byte = 0, p = 0; i < bit; i++ ) { + serial_delay_half1(); // read the middle of pulses + if( serial_read_pin() ) { + byte = (byte << 1) | 1; p ^= 1; + } else { + byte = (byte << 1) | 0; p ^= 0; + } + _delay_sub_us(READ_WRITE_WIDTH_ADJUST); + serial_delay_half2(); } + /* recive parity bit */ + serial_delay_half1(); // read the middle of pulses + pb = serial_read_pin(); + _delay_sub_us(READ_WRITE_WIDTH_ADJUST); + serial_delay_half2(); + + *pterrcount += (p != pb)? 1 : 0; + return byte; } // Sends a byte with MSB ordering -static -void serial_write_byte(uint8_t data) { - uint8_t b = 1<<7; - while( b ) { - if(data & b) { - serial_high(); - } else { - serial_low(); +void serial_write_chunk(uint8_t data, uint8_t bit) NO_INLINE; +void serial_write_chunk(uint8_t data, uint8_t bit) { + uint8_t b, p; + for( p = 0, b = 1<<(bit-1); b ; b >>= 1) { + if(data & b) { + serial_high(); p ^= 1; + } else { + serial_low(); p ^= 0; + } + serial_delay(); } - b >>= 1; + /* send parity bit */ + if(p & 1) { serial_high(); } + else { serial_low(); } serial_delay(); - } - serial_low(); // sync_send() / senc_recv() need raise edge -} -// interrupt handle to be used by the slave device -ISR(SERIAL_PIN_INTERRUPT) { - serial_output(); + serial_low(); // sync_send() / senc_recv() need raise edge +} - // slave send phase - uint8_t checksum = 0; - for (int i = 0; i < SERIAL_SLAVE_BUFFER_LENGTH; ++i) { +static void serial_send_packet(uint8_t *buffer, uint8_t size) NO_INLINE; +static +void serial_send_packet(uint8_t *buffer, uint8_t size) { + for (uint8_t i = 0; i < size; ++i) { + uint8_t data; + data = buffer[i]; sync_send(); - serial_write_byte(serial_slave_buffer[i]); - checksum += serial_slave_buffer[i]; + serial_write_chunk(data,8); } - sync_send(); - serial_write_byte(checksum); - - // slave switch to input - sync_send(); //0 - serial_delay_half1(); //1 - serial_low(); //2 - serial_input_with_pullup(); //2 - serial_delay_half1(); //3 - - // slave recive phase - uint8_t checksum_computed = 0; - for (int i = 0; i < SERIAL_MASTER_BUFFER_LENGTH; ++i) { +} + +static uint8_t serial_recive_packet(uint8_t *buffer, uint8_t size) NO_INLINE; +static +uint8_t serial_recive_packet(uint8_t *buffer, uint8_t size) { + uint8_t pecount = 0; + for (uint8_t i = 0; i < size; ++i) { + uint8_t data; sync_recv(); - serial_master_buffer[i] = serial_read_byte(); - checksum_computed += serial_master_buffer[i]; + data = serial_read_chunk(&pecount, 8); + buffer[i] = data; } + return pecount == 0; +} + +inline static +void change_sender2reciver(void) { + sync_send(); //0 + serial_delay_half1(); //1 + serial_low(); //2 + serial_input_with_pullup(); //2 + serial_delay_half1(); //3 +} + +inline static +void change_reciver2sender(void) { + sync_recv(); //0 + serial_delay(); //1 + serial_low(); //3 + serial_output(); //3 + serial_delay_half1(); //4 +} + +// interrupt handle to be used by the target device +ISR(SERIAL_PIN_INTERRUPT) { + +#ifndef SERIAL_USE_MULTI_TRANSACTION + serial_low(); + serial_output(); + SSTD_t *trans = Transaction_table; +#else + // recive transaction table index + uint8_t tid; + uint8_t pecount = 0; sync_recv(); - uint8_t checksum_received = serial_read_byte(); + tid = serial_read_chunk(&pecount,4); + if(pecount> 0) + return; + serial_delay_half1(); - if ( checksum_computed != checksum_received ) { - status |= SLAVE_DATA_CORRUPT; + serial_high(); // response step1 low->high + serial_output(); + _delay_sub_us(SLAVE_INT_ACK_WIDTH_UNIT*SLAVE_INT_ACK_WIDTH); + SSTD_t *trans = &Transaction_table[tid]; + serial_low(); // response step2 ack high->low +#endif + + // target send phase + if( trans->target2initiator_buffer_size > 0 ) + serial_send_packet((uint8_t *)trans->target2initiator_buffer, + trans->target2initiator_buffer_size); + // target switch to input + change_sender2reciver(); + + // target recive phase + if( trans->initiator2target_buffer_size > 0 ) { + if (serial_recive_packet((uint8_t *)trans->initiator2target_buffer, + trans->initiator2target_buffer_size) ) { + *trans->status = TRANSACTION_ACCEPTED; + } else { + *trans->status = TRANSACTION_DATA_ERROR; + } } else { - status &= ~SLAVE_DATA_CORRUPT; + *trans->status = TRANSACTION_ACCEPTED; } - sync_recv(); //weit master output to high -} - -inline -bool serial_slave_DATA_CORRUPT(void) { - return status & SLAVE_DATA_CORRUPT; + sync_recv(); //weit initiator output to high } -// Copies the serial_slave_buffer to the master and sends the -// serial_master_buffer to the slave. +///////// +// start transaction by initiator +// +// int soft_serial_transaction(int sstd_index) // // Returns: -// 0 => no error -// 1 => slave did not respond -// 2 => checksum error -int serial_update_buffers(void) { - // this code is very time dependent, so we need to disable interrupts +// TRANSACTION_END +// TRANSACTION_NO_RESPONSE +// TRANSACTION_DATA_ERROR +// this code is very time dependent, so we need to disable interrupts +#ifndef SERIAL_USE_MULTI_TRANSACTION +int soft_serial_transaction(void) { + SSTD_t *trans = Transaction_table; +#else +int soft_serial_transaction(int sstd_index) { + SSTD_t *trans = &Transaction_table[sstd_index]; +#endif cli(); - // signal to the slave that we want to start a transaction + // signal to the target that we want to start a transaction serial_output(); serial_low(); - _delay_us(SLAVE_INT_WIDTH); + _delay_us(SLAVE_INT_WIDTH_US); - // wait for the slaves response +#ifndef SERIAL_USE_MULTI_TRANSACTION + // wait for the target response serial_input_with_pullup(); _delay_us(SLAVE_INT_RESPONSE_TIME); - // check if the slave is present + // check if the target is present if (serial_read_pin()) { - // slave failed to pull the line low, assume not present + // target failed to pull the line low, assume not present serial_output(); serial_high(); + *trans->status = TRANSACTION_NO_RESPONSE; sei(); - return 1; + return TRANSACTION_NO_RESPONSE; } - // master recive phase - // if the slave is present syncronize with it +#else + // send transaction table index + sync_send(); + _delay_sub_us(TID_SEND_ADJUST); + serial_write_chunk(sstd_index, 4); + serial_delay_half1(); - uint8_t checksum_computed = 0; - // receive data from the slave - for (int i = 0; i < SERIAL_SLAVE_BUFFER_LENGTH; ++i) { - sync_recv(); - serial_slave_buffer[i] = serial_read_byte(); - checksum_computed += serial_slave_buffer[i]; + // wait for the target response (step1 low->high) + serial_input_with_pullup(); + while( !serial_read_pin() ) { + _delay_sub_us(2); } - sync_recv(); - uint8_t checksum_received = serial_read_byte(); - if (checksum_computed != checksum_received) { - serial_output(); - serial_high(); - sei(); - return 2; + // check if the target is present (step2 high->low) + for( int i = 0; serial_read_pin(); i++ ) { + if (i > SLAVE_INT_ACK_WIDTH + 1) { + // slave failed to pull the line low, assume not present + serial_output(); + serial_high(); + *trans->status = TRANSACTION_NO_RESPONSE; + sei(); + return TRANSACTION_NO_RESPONSE; + } + _delay_sub_us(SLAVE_INT_ACK_WIDTH_UNIT); } +#endif - // master switch to output - sync_recv(); //0 - serial_delay(); //1 - serial_low(); //3 - serial_output(); // 3 - serial_delay_half1(); //4 - - // master send phase - uint8_t checksum = 0; - - for (int i = 0; i < SERIAL_MASTER_BUFFER_LENGTH; ++i) { - sync_send(); - serial_write_byte(serial_master_buffer[i]); - checksum += serial_master_buffer[i]; + // initiator recive phase + // if the target is present syncronize with it + if( trans->target2initiator_buffer_size > 0 ) { + if (!serial_recive_packet((uint8_t *)trans->target2initiator_buffer, + trans->target2initiator_buffer_size) ) { + serial_output(); + serial_high(); + *trans->status = TRANSACTION_DATA_ERROR; + sei(); + return TRANSACTION_DATA_ERROR; + } + } + + // initiator switch to output + change_reciver2sender(); + + // initiator send phase + if( trans->initiator2target_buffer_size > 0 ) { + serial_send_packet((uint8_t *)trans->initiator2target_buffer, + trans->initiator2target_buffer_size); } - sync_send(); - serial_write_byte(checksum); // always, release the line when not in use sync_send(); + *trans->status = TRANSACTION_END; sei(); - return 0; + return TRANSACTION_END; } +#ifdef SERIAL_USE_MULTI_TRANSACTION +int soft_serial_get_and_clean_status(int sstd_index) { + SSTD_t *trans = &Transaction_table[sstd_index]; + cli(); + int retval = *trans->status; + *trans->status = 0;; + sei(); + return retval; +} +#endif + #endif diff --git a/keyboards/helix/serial.h b/keyboards/helix/serial.h index c3c9569b2c..d2b7fd8e60 100644 --- a/keyboards/helix/serial.h +++ b/keyboards/helix/serial.h @@ -3,25 +3,78 @@ #include -// //////////////////////////////////////////// +// ///////////////////////////////////////////////////////////////// // Need Soft Serial defines in serial_config.h -// //////////////////////////////////////////// +// ///////////////////////////////////////////////////////////////// // ex. // #define SERIAL_PIN_DDR DDRD // #define SERIAL_PIN_PORT PORTD // #define SERIAL_PIN_INPUT PIND // #define SERIAL_PIN_MASK _BV(PD?) ?=0,2 // #define SERIAL_PIN_INTERRUPT INT?_vect ?=0,2 +// +// //// USE Simple API (OLD API, compatible with let's split serial.c) +// ex. // #define SERIAL_SLAVE_BUFFER_LENGTH MATRIX_ROWS/2 -// #define SERIAL_MASTER_BUFFER_LENGTH MATRIX_ROWS/2 +// #define SERIAL_MASTER_BUFFER_LENGTH 1 +// +// //// USE flexible API (using multi-type transaction function) +// #define SERIAL_USE_MULTI_TRANSACTION +// +// ///////////////////////////////////////////////////////////////// + -// Buffers for master - slave communication +#ifndef SERIAL_USE_MULTI_TRANSACTION +/* --- USE Simple API (OLD API, compatible with let's split serial.c) */ +#if SERIAL_SLAVE_BUFFER_LENGTH > 0 extern volatile uint8_t serial_slave_buffer[SERIAL_SLAVE_BUFFER_LENGTH]; +#endif +#if SERIAL_MASTER_BUFFER_LENGTH > 0 extern volatile uint8_t serial_master_buffer[SERIAL_MASTER_BUFFER_LENGTH]; +#endif void serial_master_init(void); void serial_slave_init(void); int serial_update_buffers(void); -bool serial_slave_data_corrupt(void); + +#endif // USE Simple API + +// Soft Serial Transaction Descriptor +typedef struct _SSTD_t { + uint8_t *status; + uint8_t initiator2target_buffer_size; + uint8_t *initiator2target_buffer; + uint8_t target2initiator_buffer_size; + uint8_t *target2initiator_buffer; +} SSTD_t; + +// initiator is transaction start side +void soft_serial_initiator_init(SSTD_t *sstd_table); +// target is interrupt accept side +void soft_serial_target_init(SSTD_t *sstd_table); + +// initiator resullt +#define TRANSACTION_END 0 +#define TRANSACTION_NO_RESPONSE 0x1 +#define TRANSACTION_DATA_ERROR 0x2 +#ifndef SERIAL_USE_MULTI_TRANSACTION +int soft_serial_transaction(void); +#else +int soft_serial_transaction(int sstd_index); +#endif + +// target status +// *SSTD_t.status has +// initiator: +// TRANSACTION_END +// or TRANSACTION_NO_RESPONSE +// or TRANSACTION_DATA_ERROR +// target: +// TRANSACTION_DATA_ERROR +// or TRANSACTION_ACCEPTED +#define TRANSACTION_ACCEPTED 0x4 +#ifdef SERIAL_USE_MULTI_TRANSACTION +int soft_serial_get_and_clean_status(int sstd_index); +#endif #endif /* SOFT_SERIAL_H */ -- cgit v1.2.3 From e5f201edb426b01537abd659e1ca317260d87654 Mon Sep 17 00:00:00 2001 From: Biacco42 Date: Sun, 12 Aug 2018 05:22:32 +0900 Subject: Keymap: Port ergo42/biacco keymap to Helix pico (#3585) * Port ergo42/biacco keymap to Helix pico * Fix for review --- keyboards/helix/pico/keymaps/biacco/config.h | 29 +++++++ keyboards/helix/pico/keymaps/biacco/keymap.c | 118 +++++++++++++++++++++++++ keyboards/helix/pico/keymaps/biacco/rules.mk | 125 +++++++++++++++++++++++++++ 3 files changed, 272 insertions(+) create mode 100644 keyboards/helix/pico/keymaps/biacco/config.h create mode 100644 keyboards/helix/pico/keymaps/biacco/keymap.c create mode 100644 keyboards/helix/pico/keymaps/biacco/rules.mk (limited to 'keyboards/helix') diff --git a/keyboards/helix/pico/keymaps/biacco/config.h b/keyboards/helix/pico/keymaps/biacco/config.h new file mode 100644 index 0000000000..776eecfb64 --- /dev/null +++ b/keyboards/helix/pico/keymaps/biacco/config.h @@ -0,0 +1,29 @@ +/* +This is the c configuration file for the keymap + +Copyright 2012 Jun Wako +Copyright 2015 Jack Humbert + +This program is free software: you can redistribute it and/or modify +it under the terms of the GNU General Public License as published by +the Free Software Foundation, either version 2 of the License, or +(at your option) any later version. + +This program is distributed in the hope that it will be useful, +but WITHOUT ANY WARRANTY; without even the implied warranty of +MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +GNU General Public License for more details. + +You should have received a copy of the GNU General Public License +along with this program. If not, see . +*/ + +#pragma once + +// place overrides here + +#ifdef AUDIO_ENABLE + #define STARTUP_SONG SONG(STARTUP_SOUND) + #define AUDIO_CLICKY +#endif + diff --git a/keyboards/helix/pico/keymaps/biacco/keymap.c b/keyboards/helix/pico/keymaps/biacco/keymap.c new file mode 100644 index 0000000000..b4ee4fcaa9 --- /dev/null +++ b/keyboards/helix/pico/keymaps/biacco/keymap.c @@ -0,0 +1,118 @@ +#include QMK_KEYBOARD_H +#include "bootloader.h" +#ifdef PROTOCOL_LUFA +#include "lufa.h" +#include "split_util.h" +#endif +#ifdef AUDIO_ENABLE + #include "audio.h" +#endif +#ifdef SSD1306OLED + #include "ssd1306.h" +#endif + +extern keymap_config_t keymap_config; + +#ifdef RGBLIGHT_ENABLE +//Following line allows macro to read current RGB settings +extern rgblight_config_t rgblight_config; +#endif + +extern uint8_t is_master; + +// Each layer gets a name for readability, which is then used in the keymap matrix below. +// The underscores don't mean anything - you can have a layer called STUFF or any other name. +// Layer names don't all need to be of the same length, obviously, and you can also skip them +// entirely and just use numbers. +enum layer_number { + BASE = 0, + META, + SYMB, + GAME +}; + +// Fillers to make layering more clear +#define _______ KC_TRNS +#define XXXXXXX KC_NO +//Macros + +const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = { + + /* Qwerty + * ,-----------------------------------------. ,-----------------------------------------. + * | Tab | Q | W | E | R | T | | Y | U | I | O | P | @ | + * |------+------+------+------+------+------| |------+------+------+------+------+------| + * | Alt | A | S | D | F | G | | H | J | K | L | ; | : | + * |------+------+------+------+------+------| |------+------+------+------+------+------| + * | Shift| Z | X | C | V | B | | N | M | , | . | / |\/Sft | + * |------+------+------+------+------+------+-------------+------+------+------+------+------+------| + * | Ctrl | GUI | App | PrtSc| ESC/ |Space/|Tab/ |Back |Enter/| Del |PrtSc |=>GAME|=>SYMB| \ | + * | | | | | ~SYMB|RCtrl |Shift |Space |~META | | | | | | + * `-------------------------------------------------------------------------------------------------' + */ + +[BASE] = LAYOUT( \ + KC_TAB, KC_Q, KC_W, KC_E, KC_R, KC_T, KC_Y, KC_U, KC_I, KC_O, KC_P, KC_LBRC, \ + KC_LALT, KC_A, KC_S, KC_D, KC_F, KC_G, KC_H, KC_J, KC_K, KC_L, KC_SCLN, KC_QUOT, \ + KC_LSFT, KC_Z, KC_X, KC_C, KC_V, KC_B, KC_N, KC_M, KC_COMM, KC_DOT, KC_SLSH, SFT_T(KC_RO) , \ + KC_LCTL, KC_LGUI, KC_APP, KC_PSCR, LT(SYMB, KC_ESC), RCTL_T(KC_SPC), SFT_T(KC_TAB), KC_BSPC, LT(META, KC_ENT), KC_DELT, KC_PSCR, TG(GAME), TG(SYMB), KC_JYEN \ + ), + + /* META + * ,-----------------------------------------. ,-----------------------------------------. + * | 1 | 2 | 3 | 4 | 5 | 6 | | 7 | 8 | 9 | 0 | - | ^ | + * |------+------+------+------+------+------| |------+------+------+------+------+------| + * | Alt | F1 | |Muhen | Henk | | | Left | Down | Up |Right | | | + * |------+------+------+------+------+------| |------+------+------+------+------+------| + * | Sft | F2 | F3 | F4 | F5 | F6 | | F7 | F8 | F9 | F10 | F11 |\/Sft | + * |------+------+------+------+------+------+-------------+------+------+------+------+------+------| + * | Ctrl | GUI | App |PrtSc |ESC/ |Space/|Tab/ |Back |Enter/| Del |Reset |=>GAME|=>SYMB| \ | + * | | | | |~SYMB |RCtrl |Shift |Space |~META | | | | | | + * `-------------------------------------------------------------------------------------------------' + */ + [META] = LAYOUT( \ + KC_1, KC_2, KC_3, KC_4, KC_5, KC_6, KC_7, KC_8, KC_9, KC_0, KC_MINS, KC_EQL, \ + _______, KC_F1, XXXXXXX, KC_MHEN, KC_HENK, XXXXXXX, KC_LEFT, KC_DOWN, KC_UP, KC_RGHT, XXXXXXX, XXXXXXX, \ + _______, KC_F2, KC_F3, KC_F4, KC_F5, KC_F6, KC_F7, KC_F8, KC_F9, KC_F10, KC_F11, SFT_T(KC_RO), \ + _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, RESET, _______, _______, _______ \ + ), + + /* SYMB + * ,-----------------------------------------. ,-----------------------------------------. + * | ! | " | # | $ | % | & | | ' | ( | ) | ~ | = | ~ | + * |------+------+------+------+------+------| |------+------+------+------+------+------| + * | Alt | | | | | | | ( | ) | { | } | + | * | + * |------+------+------+------+------+------| |------+------+------+------+------+------| + * | Sft | | | | | | | [ | ] | < | > | ? | \ | + * |------+------+------+------+------+------+-------------+------+------+------+------+------+------| + * | Ctrl | GUI | App |PrtSc |ESC/ |Space/|Tab/ |Back |Enter/| Del |PrtSc |=>GAME|=>SYMB| \ | + * | | | | |~SYMB |RCtrl |Shift |Space |~META | | | | | | + * `-------------------------------------------------------------------------------------------------' + */ + [SYMB] = LAYOUT( \ + S(KC_1), S(KC_2), S(KC_3), S(KC_4), S(KC_5), S(KC_6), S(KC_7), S(KC_8), S(KC_9), S(KC_0), S(KC_MINS), S(KC_EQL), \ + _______, XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, S(KC_8), S(KC_9), S(KC_RBRC), S(KC_BSLS), S(KC_SCLN), S(KC_QUOT), \ + _______, XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, KC_RBRC, KC_BSLS, S(KC_COMM), S(KC_DOT), S(KC_SLSH), S(KC_RO), \ + _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______ \ + ), + + /* GAME + * ,-----------------------------------------. ,-----------------------------------------. + * | Tab | Q | W | E | R | T | | Y | U | I | O | P | @ | + * |------+------+------+------+------+------| |------+------+------+------+------+------| + * | Alt | A | S | D | F | G | | H | J | K | L | ; | : | + * |------+------+------+------+------+------| |------+------+------+------+------+------| + * | Sft | Z | X | C | V | B | | N | M | , | . | / |\/Sft | + * |------+------+------+------+------+------+-------------+------+------+------+------+------+------| + * | Ctrl | GUI | App |PrtSc | ESC |Space |Tab |Back |Enter | Del |PrtSc |=>GAME|=>SYMB| \ | + * | | | | | | | |Space | | | | | | | + * `-------------------------------------------------------------------------------------------------' + */ + [GAME] = LAYOUT( \ + KC_TAB, KC_Q, KC_W, KC_E, KC_R, KC_T, KC_Y, KC_U, KC_I, KC_O, KC_P, KC_LBRC, \ + KC_LALT, KC_A, KC_S, KC_D, KC_F, KC_G, KC_H, KC_J, KC_K, KC_L, KC_SCLN, KC_QUOT, \ + KC_LSFT, KC_Z, KC_X, KC_C, KC_V, KC_B, KC_N, KC_M, KC_COMM, KC_DOT, KC_SLSH, SFT_T(KC_RO), \ + KC_LCTRL, KC_LGUI, KC_APP, KC_PSCR, KC_ESC, KC_SPC, KC_TAB, KC_BSPC, KC_ENT, KC_DELT, KC_PSCR, _______, _______, KC_JYEN \ + ) + +}; diff --git a/keyboards/helix/pico/keymaps/biacco/rules.mk b/keyboards/helix/pico/keymaps/biacco/rules.mk new file mode 100644 index 0000000000..0a720002d7 --- /dev/null +++ b/keyboards/helix/pico/keymaps/biacco/rules.mk @@ -0,0 +1,125 @@ + +# Build Options +# change to "no" to disable the options, or define them in the Makefile in +# the appropriate keymap folder that will get included automatically +# +BOOTMAGIC_ENABLE = no # Virtual DIP switch configuration(+1000) +MOUSEKEY_ENABLE = no # Mouse keys(+4700) +EXTRAKEY_ENABLE = yes # Audio control and System control(+450) +CONSOLE_ENABLE = no # Console for debug(+400) +COMMAND_ENABLE = no # Commands for debug and configuration +NKRO_ENABLE = no # Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work +BACKLIGHT_ENABLE = no # Enable keyboard backlight functionality +MIDI_ENABLE = no # MIDI controls +AUDIO_ENABLE = yes # Audio output on port B5 +UNICODE_ENABLE = no # Unicode +BLUETOOTH_ENABLE = no # Enable Bluetooth with the Adafruit EZ-Key HID +RGBLIGHT_ENABLE = no # Enable WS2812 RGB underlight. Do not enable this with audio at the same time. +SWAP_HANDS_ENABLE = no # Enable one-hand typing + +define HELIX_CUSTOMISE_MSG + $(info Helix customize) + $(info - OLED_ENABLE=$(OLED_ENABLE)) + $(info - LED_BACK_ENABLE=$(LED_BACK_ENABLE)) + $(info - LED_UNDERGLOW_ENABLE=$(LED_UNDERGLOW_ENABLE)) + $(info - LED_ANIMATION=$(LED_ANIMATIONS)) + $(info - IOS_DEVICE_ENABLE=$(IOS_DEVICE_ENABLE)) +endef + +# Helix keyboard customize +# you can edit follows 6 Variables +# jp: 以下の6つの変数を必要に応じて編集します。 +OLED_ENABLE = no # OLED_ENABLE +LOCAL_GLCDFONT = no # use each keymaps "helixfont.h" insted of "common/glcdfont.c" +LED_BACK_ENABLE = no # LED backlight (Enable WS2812 RGB underlight.) +LED_UNDERGLOW_ENABLE = no # LED underglow (Enable WS2812 RGB underlight.) +LED_ANIMATIONS = no # LED animations +IOS_DEVICE_ENABLE = no # connect to IOS device (iPad,iPhone) +Link_Time_Optimization = no # if firmware size over limit, try this option + +#### LED_BACK_ENABLE and LED_UNDERGLOW_ENABLE. +#### Do not enable these with audio at the same time. + +### Helix keyboard 'default' keymap: convenient command line option +## make HELIX= helix:defualt +## option= oled | back | under | na | ios +## ex. +## make HELIX=oled helix:defualt +## make HELIX=oled,back helix:defualt +## make HELIX=oled,under helix:defualt +## make HELIX=oled,back,na helix:defualt +## make HELIX=oled,back,ios helix:defualt +## +ifneq ($(strip $(HELIX)),) + ifeq ($(findstring oled,$(HELIX)), oled) + OLED_ENABLE = yes + endif + ifeq ($(findstring back,$(HELIX)), back) + LED_BACK_ENABLE = yes + else ifeq ($(findstring under,$(HELIX)), under) + LED_UNDERGLOW_ENABLE = yes + endif + ifeq ($(findstring na,$(HELIX)), na) + LED_ANIMATIONS = no + endif + ifeq ($(findstring ios,$(HELIX)), ios) + IOS_DEVICE_ENABLE = yes + endif + $(eval $(call HELIX_CUSTOMISE_MSG)) + $(info ) +endif + +# Uncomment these for checking +# jp: コンパイル時にカスタマイズの状態を表示したい時はコメントをはずします。 +# $(eval $(call HELIX_CUSTOMISE_MSG)) +# $(info ) + +ifeq ($(strip $(LED_BACK_ENABLE)), yes) + RGBLIGHT_ENABLE = yes + OPT_DEFS += -DRGBLED_BACK + ifeq ($(strip $(LED_UNDERGLOW_ENABLE)), yes) + $(eval $(call HELIX_CUSTOMISE_MSG)) + $(error LED_BACK_ENABLE and LED_UNDERGLOW_ENABLE both 'yes') + endif +else ifeq ($(strip $(LED_UNDERGLOW_ENABLE)), yes) + RGBLIGHT_ENABLE = yes +else + RGBLIGHT_ENABLE = no +endif + +ifeq ($(strip $(IOS_DEVICE_ENABLE)), yes) + OPT_DEFS += -DIOS_DEVICE_ENABLE +endif + +ifeq ($(strip $(LED_ANIMATIONS)), yes) + OPT_DEFS += -DRGBLIGHT_ANIMATIONS +endif + +ifeq ($(strip $(OLED_ENABLE)), yes) + OPT_DEFS += -DOLED_ENABLE +endif + +ifeq ($(strip $(LOCAL_GLCDFONT)), yes) + OPT_DEFS += -DLOCAL_GLCDFONT +endif + +ifeq ($(strip $(AUDIO_ENABLE)),yes) + ifeq ($(strip $(RGBLIGHT_ENABLE)),yes) + Link_Time_Optimization = yes + endif + ifeq ($(strip $(OLED_ENABLE)),yes) + Link_Time_Optimization = yes + endif +endif + +ifeq ($(strip $(Link_Time_Optimization)),yes) + EXTRAFLAGS += -flto -DUSE_Link_Time_Optimization +endif + +# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE +SLEEP_LED_ENABLE = no # Breathing sleep LED during USB suspend + +# Uncomment these for debugging +# $(info -- RGBLIGHT_ENABLE=$(RGBLIGHT_ENABLE)) +# $(info -- OPT_DEFS=$(OPT_DEFS)) +# $(info ) -- cgit v1.2.3 From b3d80d4af011be30e6cdf55230d27e20a34b31a1 Mon Sep 17 00:00:00 2001 From: MakotoKurauchi Date: Thu, 16 Aug 2018 01:30:34 +0900 Subject: Keymap: Helix : Update froggy keymap (#3652) * led ripple effect * fix key name --- keyboards/helix/rev2/keymaps/froggy/keymap.c | 122 ++++++++++++++++++++++----- 1 file changed, 101 insertions(+), 21 deletions(-) (limited to 'keyboards/helix') diff --git a/keyboards/helix/rev2/keymaps/froggy/keymap.c b/keyboards/helix/rev2/keymaps/froggy/keymap.c index 5ac927af3e..81a28dfa5d 100644 --- a/keyboards/helix/rev2/keymaps/froggy/keymap.c +++ b/keyboards/helix/rev2/keymaps/froggy/keymap.c @@ -81,7 +81,7 @@ const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = { * |------+------+------+------+------+------+------+------+------+------+------+------+------+------| * | Shift| Y | S | N | I | U |Space | | | | | | | | * |------+------+------+------+------+------+------+------+------+------+------+------+------+------| - * | Ctrl | Alt | win | Sym | Num | OPT | Ent | | | | | | | | + * | Ctrl | Alt | Gui | Sym | Num | OPT | Ent | | | | | | | | * `-------------------------------------------------------------------------------------------------' */ [_BASE] = LAYOUT( \ @@ -256,8 +256,31 @@ void register_delay_code(uint8_t layer){ } } +#ifdef RGBLIGHT_ENABLE +struct keybuf { + char col, row; + char frame; +}; +struct keybuf keybufs[256]; +unsigned char keybuf_begin, keybuf_end; + +int col, row; +#endif + bool process_record_user(uint16_t keycode, keyrecord_t *record) { + #ifdef RGBLIGHT_ENABLE + col = record->event.key.col; + row = record->event.key.row; + if (record->event.pressed && ((row < 5 && is_master) || (row >= 5 && !is_master))) { + int end = keybuf_end; + keybufs[end].col = col; + keybufs[end].row = row % 5; + keybufs[end].frame = 0; + keybuf_end ++; + } + #endif + if(tap_timer&&keycode!=OPT_TAP_SP){ tapping_key = true; } @@ -475,6 +498,61 @@ void music_scale_user(void) #define L_NFNLAYER 192 #define L_MOUSECURSOR 256 +// LED Effect +#ifdef RGBLIGHT_ENABLE +unsigned char rgb[7][5][3]; +void led_ripple_effect(char r, char g, char b) { + static int scan_count = -10; + static int keys[] = { 6, 6, 6, 7, 7 }; + static int keys_sum[] = { 0, 6, 12, 18, 25 }; + + if (scan_count == -1) { + rgblight_enable_noeeprom(); + rgblight_mode(0); + } else if (scan_count >= 0 && scan_count < 5) { + for (unsigned char c=keybuf_begin; c!=keybuf_end; c++) { + int i = c; + // FIXME: + + int y = scan_count; + int dist_y = abs(y - keybufs[i].row); + for (int x=0; x= 6 && scan_count <= 10) { + int y = scan_count - 6; + for (int x=0; x= 12) { scan_count = 0; } +} +#endif uint8_t layer_state_old; @@ -494,42 +572,44 @@ void matrix_scan_user(void) { if(layer_state_old != layer_state){ switch (layer_state) { case L_BASE: - #ifdef RGBLIGHT_ENABLE - if (!RGBAnimation){ - rgblight_sethsv(187,255,255); - rgblight_mode(1); - }else{ - rgblight_mode(RGB_current_mode); - } - #endif break; case L_OPT: register_delay_code(_OPT); break; case L_NUM: register_delay_code(_NUM); - #ifdef RGBLIGHT_ENABLE - rgblight_sethsv(25,255,255); - rgblight_mode(1); - #endif break; case L_SYM: register_delay_code(_SYM); - #ifdef RGBLIGHT_ENABLE - rgblight_sethsv(96,255,255); - rgblight_mode(1); - #endif break; case L_FUNC: register_delay_code(_FUNC); - #ifdef RGBLIGHT_ENABLE - rgblight_sethsv(331,255,255); - rgblight_mode(1); - #endif break; } layer_state_old = layer_state; } + + #ifdef RGBLIGHT_ENABLE + if(!RGBAnimation){ + switch (layer_state) { + case L_BASE: + led_ripple_effect(0,112,127); + break; + case L_OPT: + led_ripple_effect(127,0,100); + break; + case L_NUM: + led_ripple_effect(127,23,0); + break; + case L_SYM: + led_ripple_effect(0,127,0); + break; + case L_FUNC: + led_ripple_effect(127,0,61); + break; + } + } + #endif } //SSD1306 OLED update loop, make sure to add #define SSD1306OLED in config.h -- cgit v1.2.3 From 97d09ef8fabed45fb409b0b620f3ae3867d5ed50 Mon Sep 17 00:00:00 2001 From: Takeshi ISHII <2170248+mtei@users.noreply.github.com> Date: Thu, 30 Aug 2018 10:12:09 +0900 Subject: Keyboard: remove old comment from keyboards/helix/rules.mk (#3795) remove 2 lines from keyboards/helix/rules.mk | -# if firmware size over limit, try this option | -# CFLAGS += -flto | - see keyboards/helix/[rev2|pico]/keymaps/EACH_MAP/rules.mk: | Link_Time_Optimization = no # if firmware size over limit, try this option : : : | ifeq ($(strip $(Link_Time_Optimization)),yes) | EXTRAFLAGS += -flto -DUSE_Link_Time_Optimization | endif --- keyboards/helix/rules.mk | 3 --- 1 file changed, 3 deletions(-) (limited to 'keyboards/helix') diff --git a/keyboards/helix/rules.mk b/keyboards/helix/rules.mk index e42f92cf8a..7c1d56527a 100644 --- a/keyboards/helix/rules.mk +++ b/keyboards/helix/rules.mk @@ -2,9 +2,6 @@ SRC += i2c.c SRC += serial.c SRC += ssd1306.c -# if firmware size over limit, try this option -# CFLAGS += -flto - # MCU name #MCU = at90usb1287 MCU = atmega32u4 -- cgit v1.2.3 From ffc2dc0359ee3eee4eea8605082cfc210b1bc53d Mon Sep 17 00:00:00 2001 From: Yasuhiro Shimizu Date: Sun, 2 Sep 2018 01:38:29 +0900 Subject: Keymap: add yshrsmz keymaps (#3770) * add ergo42 keymap * add helix keymap * add keymap for lets_split * Add keymap for nyquist * update keymaps to address review comments - remove unneeded include - use `#pragma once` --- keyboards/helix/rev2/keymaps/yshrsmz/config.h | 23 + keyboards/helix/rev2/keymaps/yshrsmz/keymap.c | 558 +++++++++++++++++++++++++ keyboards/helix/rev2/keymaps/yshrsmz/readme.md | 25 ++ keyboards/helix/rev2/keymaps/yshrsmz/rules.mk | 121 ++++++ 4 files changed, 727 insertions(+) create mode 100644 keyboards/helix/rev2/keymaps/yshrsmz/config.h create mode 100644 keyboards/helix/rev2/keymaps/yshrsmz/keymap.c create mode 100644 keyboards/helix/rev2/keymaps/yshrsmz/readme.md create mode 100644 keyboards/helix/rev2/keymaps/yshrsmz/rules.mk (limited to 'keyboards/helix') diff --git a/keyboards/helix/rev2/keymaps/yshrsmz/config.h b/keyboards/helix/rev2/keymaps/yshrsmz/config.h new file mode 100644 index 0000000000..a1cd126eef --- /dev/null +++ b/keyboards/helix/rev2/keymaps/yshrsmz/config.h @@ -0,0 +1,23 @@ +/* +This is the c configuration file for the keymap + +Copyright 2012 Jun Wako +Copyright 2015 Jack Humbert + +This program is free software: you can redistribute it and/or modify +it under the terms of the GNU General Public License as published by +the Free Software Foundation, either version 2 of the License, or +(at your option) any later version. + +This program is distributed in the hope that it will be useful, +but WITHOUT ANY WARRANTY; without even the implied warranty of +MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +GNU General Public License for more details. + +You should have received a copy of the GNU General Public License +along with this program. If not, see . +*/ +#pragma once + +/* auto shift config */ +#define AUTO_SHIFT_TIMEOUT 150 diff --git a/keyboards/helix/rev2/keymaps/yshrsmz/keymap.c b/keyboards/helix/rev2/keymaps/yshrsmz/keymap.c new file mode 100644 index 0000000000..cce28796e6 --- /dev/null +++ b/keyboards/helix/rev2/keymaps/yshrsmz/keymap.c @@ -0,0 +1,558 @@ +#include QMK_KEYBOARD_H +#include "bootloader.h" +#ifdef PROTOCOL_LUFA +#include "lufa.h" +#include "split_util.h" +#endif +#ifdef AUDIO_ENABLE + #include "audio.h" +#endif +#ifdef SSD1306OLED + #include "ssd1306.h" +#endif + +extern keymap_config_t keymap_config; + +#ifdef RGBLIGHT_ENABLE +//Following line allows macro to read current RGB settings +extern rgblight_config_t rgblight_config; +#endif + +extern uint8_t is_master; + +// Each layer gets a name for readability, which is then used in the keymap matrix below. +// The underscores don't mean anything - you can have a layer called STUFF or any other name. +// Layer names don't all need to be of the same length, obviously, and you can also skip them +// entirely and just use numbers. +enum layer_number { + _QWERTY = 0, + _LOWER, + _RAISE, + _FUNC, + _ADJUST +}; + +enum custom_keycodes { + QWERTY = SAFE_RANGE, + LOWER, + RAISE, + FUNC, + ADJUST, + EISU, + KANA +}; + +enum macro_keycodes { + KC_SAMPLEMACRO, +}; + + +// Fillers to make layering more clear +#define _______ KC_TRNS +#define XXXXXXX KC_NO +//Macros +#define M_SAMPLE M(KC_SAMPLEMACRO) + +#if HELIX_ROWS == 5 +const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = { + + /* Qwerty + * ,-----------------------------------------. ,-----------------------------------------. + * | ` | 1 | 2 | 3 | 4 | 5 | | 6 | 7 | 8 | 9 | 0 | = | + * |------+------+------+------+------+------| |------+------+------+------+------+------| + * | Tab | Q | W | E | R | T | | Y | U | I | O | P | - | + * |------+------+------+------+------+------| |------+------+------+------+------+------| + * | ESC | A | S | D | F | G | | H | J | K | L | ; | ' | + * |------+------+------+------+------+------+------+------+------+------+------+------+------+------| + * |Shift | Z | X | C | V | B | Fn | Fn | N | M | , | . | / |Shift | + * |------+------+------+------+------+------+------+------+------+------+------+------+------+------| + * | EISU | Ctrl | Alt | GUI |Lower |Space | Bksp |Enter |Space |Raise | GUI | Alt | Ctrl | KANA | + * `-------------------------------------------------------------------------------------------------' + */ + [_QWERTY] = LAYOUT( \ + KC_GRV, KC_1, KC_2, KC_3, KC_4, KC_5, KC_6, KC_7, KC_8, KC_9, KC_0, KC_EQL, \ + KC_TAB, KC_Q, KC_W, KC_E, KC_R, KC_T, KC_Y, KC_U, KC_I, KC_O, KC_P, KC_MINS, \ + KC_ESC, KC_A, KC_S, KC_D, KC_F, KC_G, KC_H, KC_J, KC_K, KC_L, KC_SCLN, KC_QUOT, \ + KC_LSFT, KC_Z, KC_X, KC_C, KC