From bf324c38e3a8929999e459b947b5551bc216cc88 Mon Sep 17 00:00:00 2001 From: Dmitry Nosachev Date: Tue, 22 Dec 2020 21:10:56 +0300 Subject: [Keyboard] add ASkeyboard Sono1 (#11114) * handwired/sono1 * readme: addition * Apply suggestions from code review Co-authored-by: Ryan Co-authored-by: Ryan --- keyboards/handwired/sono1/readme.md | 57 +++++++++++++++++++++++++++++++++++++ 1 file changed, 57 insertions(+) create mode 100644 keyboards/handwired/sono1/readme.md (limited to 'keyboards/handwired/sono1/readme.md') diff --git a/keyboards/handwired/sono1/readme.md b/keyboards/handwired/sono1/readme.md new file mode 100644 index 0000000000..e21d06e2d9 --- /dev/null +++ b/keyboards/handwired/sono1/readme.md @@ -0,0 +1,57 @@ +# QMK-based firmware for ASkeyboard Sono1 keyboard with additional Sono2 numpad + +![Sono1](https://i.imgur.com/eb046DOh.jpeg) + +ASkeyboard Sono1 keyboard conversion project: direct connection of Black Pill to the matrix. + +* Keyboard Maintainer: [DmNosachev](https://github.com/DmNosachev) +* Hardware Supported: [ASkeyboard Sono1](http://www5f.biglobe.ne.jp/~silencium/keyboard/html/alps.html), Black Pill STM32F103C8T6 MCU board. Alternatively you can use any MCU which is supported by QMK and has 28 IO pins or more (15x8 matrix and 5 LEDs): Teensy 2.0++, Blue Pill, etc. + +Make example for this keyboard (after setting up your build environment): + + make handwired/sono1:default + +See the [build environment setup](https://docs.qmk.fm/#/getting_started_build_tools) and the [make instructions](https://docs.qmk.fm/#/getting_started_make_guide) for more information. Brand new to QMK? Start with our [Complete Newbs Guide](https://docs.qmk.fm/#/newbs). + +# Modding + +## Matrix + +ASkeyboard Sono1 has 15x8 matrix. Sono2 numpad connects directly to the main matrix. + +Rows (R0-RE) and columns (R0-C7): +![Sono1 rows and columns](https://i.imgur.com/5Owazg6h.jpeg) + +## LEDs +Keyboard has 5 LEDs with common anode. Their cathodes are connected to R10–R14 resistors (you may want to replace them to adjust LED brightness for 3.3V voltage). Add 5 wire jumpers to connect them to the corresponding traces. + +![Sono1 LEDs](https://i.imgur.com/opxc2A3h.jpeg) + +## Black Pill +Suggested mount position for the Black Pill (view from the bottom side of the PCB): + +``` + R8 R9 RA RB RC RD RE L0 Vcc C7 C6 C5 C4 C3 C2 C1 C0 Vcc + * | | | * | | | | | | | | | * * * + ,------------------------------------------------------------------------, +,---|GND B8 B9 C13 RST A0 A1 A2 A3 A4 A5 A6 A7 B0 B1 B10 B11 3V3| A3 A4 3V3 +| | B7 A15 A13| +|USB| A14| +| | B12 A10 GND| +'---|GND 3V3 B7 B6 B5 B4 B3 A15 A12 A11 A10 A9 A8 B15 B14 B13 B12 | + '------------------------------------------------------------------------' A9 B3 A5 + | | | | * | | | | * * * * + GND L2 L1 L3 L4 R7 R6 R5 R4 R3 R2 R1 R0 +``` +Asterisk sign designates pins of the Black Pill that don't align properly with PCB and need to be rewired. + +![Black Pill](https://i.imgur.com/KQjTWVbh.jpeg) + +1. Desolder all ICs, capacitors and resistors except R10–R14. +1. Solder 4-pin SWD header to Black Pill. +2. Burn [STM32duino bootloader](https://github.com/rogerclarkmelbourne/STM32duino-bootloader/blob/master/bootloader_only_binaries/generic_boot20_pb12.bin) to Black Pill. +3. Compile and flash the firmware: `make handwired/sono1:default:flash` +4. Connect rows, columns and LED pads to the corresponding pins of the Black Pill. + +## Keymap +'CUR LOCK' key on Sono2 numpad has locking switch by default (Alps SKCL lock). QMK [supports mechanical locking switches](https://docs.qmk.fm/#/faq_keymap?id=mechanical-lock-switch-support) for CapsLock, NumLock and ScrollLock keycodes. -- cgit v1.2.3