From e8b65d01709c2ebdf50c0aa95963d200fa4fa4c6 Mon Sep 17 00:00:00 2001 From: fauxpark Date: Sun, 6 Oct 2019 05:09:35 +1100 Subject: Cleanup rules.mk for 32U4 keyboards, A-F (#6804) * Cleanup rules.mk for 32U4 keyboards, A-F * Put back stuff in VIA keymaps --- keyboards/converter/adb_usb/rules.mk | 59 ++++--------------------- keyboards/converter/hp_46010a/rules.mk | 47 ++++---------------- keyboards/converter/ibm_5291/rules.mk | 47 ++++---------------- keyboards/converter/ibm_terminal/rules.mk | 51 ++++----------------- keyboards/converter/m0110_usb/rules.mk | 58 ++++-------------------- keyboards/converter/numeric_keypad_IIe/rules.mk | 47 +------------------- keyboards/converter/palm_usb/rules.mk | 17 ++++--- keyboards/converter/sun_usb/rules.mk | 17 ++++--- keyboards/converter/usb_usb/rules.mk | 57 +++++------------------- keyboards/converter/xt_usb/rules.mk | 48 ++++---------------- 10 files changed, 83 insertions(+), 365 deletions(-) (limited to 'keyboards/converter') diff --git a/keyboards/converter/adb_usb/rules.mk b/keyboards/converter/adb_usb/rules.mk index 7901898c7c..66ca765266 100644 --- a/keyboards/converter/adb_usb/rules.mk +++ b/keyboards/converter/adb_usb/rules.mk @@ -1,59 +1,16 @@ # MCU name -# atmega32u4 Teensy2.0 -# atemga32u4 TMK Converter rev.1 -# atemga32u2 TMK Converter rev.2 MCU = atmega32u4 -# Processor frequency. -# This will define a symbol, F_CPU, in all source code files equal to the -# processor frequency in Hz. You can then use this symbol in your source code to -# calculate timings. Do NOT tack on a 'UL' at the end, this will be done -# automatically to create a 32-bit value in your source code. -# -# This will be an integer division of F_USB below, as it is sourced by -# F_USB after it has run through any CPU prescalers. Note that this value -# does not *change* the processor frequency - it should merely be updated to -# reflect the processor speed set externally so that the code can use accurate -# software delays. -# -F_CPU = 16000000 -# F_CPU = 8000000 - -# -# LUFA specific -# -# Target architecture (see library "Board Types" documentation). -ARCH = AVR8 - -# Input clock frequency. -# This will define a symbol, F_USB, in all source code files equal to the -# input clock frequency (before any prescaling is performed) in Hz. This value may -# differ from F_CPU if prescaling is used on the latter, and is required as the -# raw input clock is fed directly to the PLL sections of the AVR for high speed -# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' -# at the end, this will be done automatically to create a 32-bit value in your -# source code. -# -# If no clock division is performed on the input clock inside the AVR (via the -# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. -F_USB = $(F_CPU) - -# Interrupt driven control endpoint task(+60) -OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT - -# Bootloader -# This definition is optional, and if your keyboard supports multiple bootloaders of -# different sizes, comment this out, and the correct address will be loaded -# automatically (+60). See bootloader.mk for all options. +# Bootloader selection +# Teensy halfkay +# Pro Micro caterina +# Atmel DFU atmel-dfu +# LUFA DFU lufa-dfu +# QMK DFU qmk-dfu +# ATmega32A bootloadHID +# ATmega328P USBasp BOOTLOADER = caterina -# Boot Section Size in *bytes* -# Teensy halfKay 512 -# Teensy++ halfKay 1024 -# Atmel DFU loader 4096 for TMK Converter rev.1/rev.2 -# LUFA bootloader 4096 -# USBaspLoader 2048 - # Build Options # comment out to disable the options. # diff --git a/keyboards/converter/hp_46010a/rules.mk b/keyboards/converter/hp_46010a/rules.mk index 797258caf7..b23aaadeca 100644 --- a/keyboards/converter/hp_46010a/rules.mk +++ b/keyboards/converter/hp_46010a/rules.mk @@ -1,45 +1,14 @@ # MCU name MCU = atmega32u4 -# Processor frequency. -# This will define a symbol, F_CPU, in all source code files equal to the -# processor frequency in Hz. You can then use this symbol in your source code to -# calculate timings. Do NOT tack on a 'UL' at the end, this will be done -# automatically to create a 32-bit value in your source code. -# -# This will be an integer division of F_USB below, as it is sourced by -# F_USB after it has run through any CPU prescalers. Note that this value -# does not *change* the processor frequency - it should merely be updated to -# reflect the processor speed set externally so that the code can use accurate -# software delays. -F_CPU = 16000000 - -# -# LUFA specific -# -# Target architecture (see library "Board Types" documentation). -ARCH = AVR8 - -# Input clock frequency. -# This will define a symbol, F_USB, in all source code files equal to the -# input clock frequency (before any prescaling is performed) in Hz. This value may -# differ from F_CPU if prescaling is used on the latter, and is required as the -# raw input clock is fed directly to the PLL sections of the AVR for high speed -# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' -# at the end, this will be done automatically to create a 32-bit value in your -# source code. -# -# If no clock division is performed on the input clock inside the AVR (via the -# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. -F_USB = $(F_CPU) - -# Interrupt driven control endpoint task(+60) -OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT - -# Bootloader -# This definition is optional, and if your keyboard supports multiple bootloaders of -# different sizes, comment this out, and the correct address will be loaded -# automatically (+60). See bootloader.mk for all options. +# Bootloader selection +# Teensy halfkay +# Pro Micro caterina +# Atmel DFU atmel-dfu +# LUFA DFU lufa-dfu +# QMK DFU qmk-dfu +# ATmega32A bootloadHID +# ATmega328P USBasp BOOTLOADER = halfkay # Build Options diff --git a/keyboards/converter/ibm_5291/rules.mk b/keyboards/converter/ibm_5291/rules.mk index 457dad1661..edb456a7d8 100644 --- a/keyboards/converter/ibm_5291/rules.mk +++ b/keyboards/converter/ibm_5291/rules.mk @@ -1,45 +1,14 @@ # MCU name MCU = atmega32u4 -# Processor frequency. -# This will define a symbol, F_CPU, in all source code files equal to the -# processor frequency in Hz. You can then use this symbol in your source code to -# calculate timings. Do NOT tack on a 'UL' at the end, this will be done -# automatically to create a 32-bit value in your source code. -# -# This will be an integer division of F_USB below, as it is sourced by -# F_USB after it has run through any CPU prescalers. Note that this value -# does not *change* the processor frequency - it should merely be updated to -# reflect the processor speed set externally so that the code can use accurate -# software delays. -F_CPU = 16000000 - -# -# LUFA specific -# -# Target architecture (see library "Board Types" documentation). -ARCH = AVR8 - -# Input clock frequency. -# This will define a symbol, F_USB, in all source code files equal to the -# input clock frequency (before any prescaling is performed) in Hz. This value may -# differ from F_CPU if prescaling is used on the latter, and is required as the -# raw input clock is fed directly to the PLL sections of the AVR for high speed -# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' -# at the end, this will be done automatically to create a 32-bit value in your -# source code. -# -# If no clock division is performed on the input clock inside the AVR (via the -# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. -F_USB = $(F_CPU) - -# Interrupt driven control endpoint task(+60) -OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT - -# Bootloader -# This definition is optional, and if your keyboard supports multiple bootloaders of -# different sizes, comment this out, and the correct address will be loaded -# automatically (+60). See bootloader.mk for all options. +# Bootloader selection +# Teensy halfkay +# Pro Micro caterina +# Atmel DFU atmel-dfu +# LUFA DFU lufa-dfu +# QMK DFU qmk-dfu +# ATmega32A bootloadHID +# ATmega328P USBasp BOOTLOADER = halfkay # Build Options diff --git a/keyboards/converter/ibm_terminal/rules.mk b/keyboards/converter/ibm_terminal/rules.mk index a48038ccde..36913ef331 100644 --- a/keyboards/converter/ibm_terminal/rules.mk +++ b/keyboards/converter/ibm_terminal/rules.mk @@ -1,48 +1,15 @@ # MCU name MCU = atmega32u4 -# Processor frequency. -# This will define a symbol, F_CPU, in all source code files equal to the -# processor frequency in Hz. You can then use this symbol in your source code to -# calculate timings. Do NOT tack on a 'UL' at the end, this will be done -# automatically to create a 32-bit value in your source code. -# -# This will be an integer division of F_USB below, as it is sourced by -# F_USB after it has run through any CPU prescalers. Note that this value -# does not *change* the processor frequency - it should merely be updated to -# reflect the processor speed set externally so that the code can use accurate -# software delays. -F_CPU = 16000000 - -# -# LUFA specific -# -# Target architecture (see library "Board Types" documentation). -ARCH = AVR8 - -# Input clock frequency. -# This will define a symbol, F_USB, in all source code files equal to the -# input clock frequency (before any prescaling is performed) in Hz. This value may -# differ from F_CPU if prescaling is used on the latter, and is required as the -# raw input clock is fed directly to the PLL sections of the AVR for high speed -# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' -# at the end, this will be done automatically to create a 32-bit value in your -# source code. -# -# If no clock division is performed on the input clock inside the AVR (via the -# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. -F_USB = $(F_CPU) - -# Interrupt driven control endpoint task(+60) -OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT - -# Boot Section Size in *bytes* -# Teensy halfKay 512 -# Teensy++ halfKay 1024 -# Atmel DFU loader 4096 -# LUFA bootloader 4096 -# USBaspLoader 2048 -OPT_DEFS += -DBOOTLOADER_SIZE=4096 +# Bootloader selection +# Teensy halfkay +# Pro Micro caterina +# Atmel DFU atmel-dfu +# LUFA DFU lufa-dfu +# QMK DFU qmk-dfu +# ATmega32A bootloadHID +# ATmega328P USBasp +BOOTLOADER = atmel-dfu # Build Options # change to "no" to disable the options, or define them in the Makefile in diff --git a/keyboards/converter/m0110_usb/rules.mk b/keyboards/converter/m0110_usb/rules.mk index bffee05fde..36c3dfa3fd 100644 --- a/keyboards/converter/m0110_usb/rules.mk +++ b/keyboards/converter/m0110_usb/rules.mk @@ -1,59 +1,19 @@ # MCU name -# atmega32u4 Teensy2.0 -# atemga32u4 TMK Converter rev.1 -# atemga32u2 TMK Converter rev.2 MCU = atmega32u4 -# Processor frequency. -# This will define a symbol, F_CPU, in all source code files equal to the -# processor frequency in Hz. You can then use this symbol in your source code to -# calculate timings. Do NOT tack on a 'UL' at the end, this will be done -# automatically to create a 32-bit value in your source code. -# -# This will be an integer division of F_USB below, as it is sourced by -# F_USB after it has run through any CPU prescalers. Note that this value -# does not *change* the processor frequency - it should merely be updated to -# reflect the processor speed set externally so that the code can use accurate -# software delays. -# -#F_CPU = 16000000 +# Processor frequency F_CPU = 8000000 -# -# LUFA specific -# -# Target architecture (see library "Board Types" documentation). -ARCH = AVR8 - -# Input clock frequency. -# This will define a symbol, F_USB, in all source code files equal to the -# input clock frequency (before any prescaling is performed) in Hz. This value may -# differ from F_CPU if prescaling is used on the latter, and is required as the -# raw input clock is fed directly to the PLL sections of the AVR for high speed -# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' -# at the end, this will be done automatically to create a 32-bit value in your -# source code. -# -# If no clock division is performed on the input clock inside the AVR (via the -# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. -F_USB = $(F_CPU) - -# Interrupt driven control endpoint task(+60) -OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT - -# Bootloader -# This definition is optional, and if your keyboard supports multiple bootloaders of -# different sizes, comment this out, and the correct address will be loaded -# automatically (+60). See bootloader.mk for all options. +# Bootloader selection +# Teensy halfkay +# Pro Micro caterina +# Atmel DFU atmel-dfu +# LUFA DFU lufa-dfu +# QMK DFU qmk-dfu +# ATmega32A bootloadHID +# ATmega328P USBasp BOOTLOADER = caterina -# Boot Section Size in *bytes* -# Teensy halfKay 512 -# Teensy++ halfKay 1024 -# Atmel DFU loader 4096 for TMK Converter rev.1/rev.2 -# LUFA bootloader 4096 -# USBaspLoader 2048 - # Build Options # comment out to disable the options. # diff --git a/keyboards/converter/numeric_keypad_IIe/rules.mk b/keyboards/converter/numeric_keypad_IIe/rules.mk index f61a7d4501..03c1bc8f86 100644 --- a/keyboards/converter/numeric_keypad_IIe/rules.mk +++ b/keyboards/converter/numeric_keypad_IIe/rules.mk @@ -1,59 +1,16 @@ # MCU name MCU = atmega32u4 -# Processor frequency. -# This will define a symbol, F_CPU, in all source code files equal to the -# processor frequency in Hz. You can then use this symbol in your source code to -# calculate timings. Do NOT tack on a 'UL' at the end, this will be done -# automatically to create a 32-bit value in your source code. -# -# This will be an integer division of F_USB below, as it is sourced by -# F_USB after it has run through any CPU prescalers. Note that this value -# does not *change* the processor frequency - it should merely be updated to -# reflect the processor speed set externally so that the code can use accurate -# software delays. -F_CPU = 16000000 - -# -# LUFA specific -# -# Target architecture (see library "Board Types" documentation). -ARCH = AVR8 - -# Input clock frequency. -# This will define a symbol, F_USB, in all source code files equal to the -# input clock frequency (before any prescaling is performed) in Hz. This value may -# differ from F_CPU if prescaling is used on the latter, and is required as the -# raw input clock is fed directly to the PLL sections of the AVR for high speed -# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' -# at the end, this will be done automatically to create a 32-bit value in your -# source code. -# -# If no clock division is performed on the input clock inside the AVR (via the -# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. -F_USB = $(F_CPU) - -# Interrupt driven control endpoint task(+60) -OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT - # Bootloader selection # Teensy halfkay # Pro Micro caterina # Atmel DFU atmel-dfu # LUFA DFU lufa-dfu # QMK DFU qmk-dfu -# atmega32a bootloadHID +# ATmega32A bootloadHID +# ATmega328P USBasp BOOTLOADER = caterina -# If you don't know the bootloader type, then you can specify the -# Boot Section Size in *bytes* by uncommenting out the OPT_DEFS line -# Teensy halfKay 512 -# Teensy++ halfKay 1024 -# Atmel DFU loader 4096 -# LUFA bootloader 4096 -# USBaspLoader 2048 -# OPT_DEFS += -DBOOTLOADER_SIZE=4096 - # Build Options # change yes to no to disable # diff --git a/keyboards/converter/palm_usb/rules.mk b/keyboards/converter/palm_usb/rules.mk index 7374fd955f..2cd2c47e59 100644 --- a/keyboards/converter/palm_usb/rules.mk +++ b/keyboards/converter/palm_usb/rules.mk @@ -1,11 +1,14 @@ -MCU = atmega32u4 # Teensy 2.0 -F_CPU = 16000000 -ARCH = AVR8 -F_USB = $(F_CPU) - -# Interrupt driven control endpoint task -OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT +# MCU name +MCU = atmega32u4 +# Bootloader selection +# Teensy halfkay +# Pro Micro caterina +# Atmel DFU atmel-dfu +# LUFA DFU lufa-dfu +# QMK DFU qmk-dfu +# ATmega32A bootloadHID +# ATmega328P USBasp BOOTLOADER = caterina # Build Options diff --git a/keyboards/converter/sun_usb/rules.mk b/keyboards/converter/sun_usb/rules.mk index db6b5c7ee4..60beb4d9b0 100644 --- a/keyboards/converter/sun_usb/rules.mk +++ b/keyboards/converter/sun_usb/rules.mk @@ -1,11 +1,14 @@ -MCU = atmega32u4 # Teensy 2.0 -F_CPU = 16000000 -ARCH = AVR8 -F_USB = $(F_CPU) - -# Interrupt driven control endpoint task -OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT +# MCU name +MCU = atmega32u4 +# Bootloader selection +# Teensy halfkay +# Pro Micro caterina +# Atmel DFU atmel-dfu +# LUFA DFU lufa-dfu +# QMK DFU qmk-dfu +# ATmega32A bootloadHID +# ATmega328P USBasp BOOTLOADER = lufa-dfu # Build Options diff --git a/keyboards/converter/usb_usb/rules.mk b/keyboards/converter/usb_usb/rules.mk index dfe89ee7d9..b4f37d3ad8 100644 --- a/keyboards/converter/usb_usb/rules.mk +++ b/keyboards/converter/usb_usb/rules.mk @@ -1,55 +1,16 @@ # MCU name MCU = atmega32u4 -# Processor frequency. -# This will define a symbol, F_CPU, in all source code files equal to the -# processor frequency in Hz. You can then use this symbol in your source code to -# calculate timings. Do NOT tack on a 'UL' at the end, this will be done -# automatically to create a 32-bit value in your source code. -# -# This will be an integer division of F_USB below, as it is sourced by -# F_USB after it has run through any CPU prescalers. Note that this value -# does not *change* the processor frequency - it should merely be updated to -# reflect the processor speed set externally so that the code can use accurate -# software delays. - -# Since there are different hardware variations of these adapters and since these -# have different CPU clocks, the clock speed should be set in the rules.mk file of the -# respective hardware variantion (i.e. subproject). For example, in /pro_micro/rules.mk -# this is set to 8000000. -# The value here is only a fallback and is ignored if it is defined in the subproject. -F_CPU ?= 16000000 - -DEFAULT_FOLDER = converter/usb_usb/hasu - -# -# LUFA specific -# -# Target architecture (see library "Board Types" documentation). -ARCH = AVR8 - -# Input clock frequency. -# This will define a symbol, F_USB, in all source code files equal to the -# input clock frequency (before any prescaling is performed) in Hz. This value may -# differ from F_CPU if prescaling is used on the latter, and is required as the -# raw input clock is fed directly to the PLL sections of the AVR for high speed -# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' -# at the end, this will be done automatically to create a 32-bit value in your -# source code. -# -# If no clock division is performed on the input clock inside the AVR (via the -# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. -F_USB = $(F_CPU) - -# Bootloader -# This definition is optional, and if your keyboard supports multiple bootloaders of -# different sizes, comment this out, and the correct address will be loaded -# automatically (+60). See bootloader.mk for all options. +# Bootloader selection +# Teensy halfkay +# Pro Micro caterina +# Atmel DFU atmel-dfu +# LUFA DFU lufa-dfu +# QMK DFU qmk-dfu +# ATmega32A bootloadHID +# ATmega328P USBasp BOOTLOADER = caterina -# Interrupt driven control endpoint task -OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT - # Build Options # comment out to disable the options. # @@ -65,3 +26,5 @@ USB_HID_ENABLE = yes CUSTOM_MATRIX = yes SRC = custom_matrix.cpp + +DEFAULT_FOLDER = converter/usb_usb/hasu diff --git a/keyboards/converter/xt_usb/rules.mk b/keyboards/converter/xt_usb/rules.mk index 1f96251830..05b70519c7 100644 --- a/keyboards/converter/xt_usb/rules.mk +++ b/keyboards/converter/xt_usb/rules.mk @@ -1,45 +1,15 @@ # MCU name MCU = atmega32u4 -# Processor frequency. -# This will define a symbol, F_CPU, in all source code files equal to the -# processor frequency in Hz. You can then use this symbol in your source code to -# calculate timings. Do NOT tack on a 'UL' at the end, this will be done -# automatically to create a 32-bit value in your source code. -# -# This will be an integer division of F_USB below, as it is sourced by -# F_USB after it has run through any CPU prescalers. Note that this value -# does not *change* the processor frequency - it should merely be updated to -# reflect the processor speed set externally so that the code can use accurate -# software delays. -F_CPU = 16000000 - -# -# LUFA specific -# -# Target architecture (see library "Board Types" documentation). -ARCH = AVR8 - -# Input clock frequency. -# This will define a symbol, F_USB, in all source code files equal to the -# input clock frequency (before any prescaling is performed) in Hz. This value may -# differ from F_CPU if prescaling is used on the latter, and is required as the -# raw input clock is fed directly to the PLL sections of the AVR for high speed -# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' -# at the end, this will be done automatically to create a 32-bit value in your -# source code. -# -# If no clock division is performed on the input clock inside the AVR (via the -# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. -F_USB = $(F_CPU) - -# Interrupt driven control endpoint task(+60) -OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT - -# Bootloader -# This indicates which bootloader is present on the board. -# BOOTLOADER = caterina # Pro Micro -BOOTLOADER = halfkay # Teensy +# Bootloader selection +# Teensy halfkay +# Pro Micro caterina +# Atmel DFU atmel-dfu +# LUFA DFU lufa-dfu +# QMK DFU qmk-dfu +# ATmega32A bootloadHID +# ATmega328P USBasp +BOOTLOADER = halfkay # Build Options # comment out to disable the options. -- cgit v1.2.3