From bd8e257f842e40f01041706a217be2cf85ae7f92 Mon Sep 17 00:00:00 2001 From: =?UTF-8?q?=C3=81lvaro=20A=2E=20Volpato?= Date: Fri, 28 Jan 2022 21:19:11 -0300 Subject: [Keyboard] Adds Elongate Revision Delta PCB support (#15498) Co-authored-by: Drashna Jaelre Co-authored-by: James Young <18669334+noroadsleft@users.noreply.github.com> Co-authored-by: Ryan --- keyboards/acheron/elongate/beta/readme.md | 43 +++++++++++++++++++++++++++++++ 1 file changed, 43 insertions(+) create mode 100755 keyboards/acheron/elongate/beta/readme.md (limited to 'keyboards/acheron/elongate/beta/readme.md') diff --git a/keyboards/acheron/elongate/beta/readme.md b/keyboards/acheron/elongate/beta/readme.md new file mode 100755 index 0000000000..8a8949fdfe --- /dev/null +++ b/keyboards/acheron/elongate/beta/readme.md @@ -0,0 +1,43 @@ +# Acheron Elongate rev. Beta QMK firmware repository + +![](https://i.imgur.com/G9LESkUh.jpg) + +* Keyboard Maintainer: [Gondolindrim](https://github.com/Gondolindrim) +* Hardware Supported: [open-source PCB](https://github.com/AcheronProject/Elongate) powered by STM32F072 microcontroller +* Hardware Availability: the revision beta of Elongate was never publicly sold. + +## Introduction + +This is the QMK firmware repository for the Elongate PCB revision Beta and pre-revision Beta versions, which was the initial revision PCB for this keyboard; hence it was never sold publicly. + +The Elongate PCB is an Open-Hardware-guideline-compliant PCB which files can be found at [this repository](https://github.com/AcheronProject/Elongate). Its designer and maintainer is [Gondolindrim](https://github.com/Gondolindrim). + +## How to flash + +### Enter bootloader + +The DFU state in the bootloader can be accessed in 3 ways: + +* **Bootmagic reset**: Hold down the key at (0,0) in the matrix (usually the top left key or Escape) and plug in the keyboard +* **Physical reset button**: press the button on the front of the PCB. +* **Keycode in layout**: Press the key mapped to `RESET` if it is available. + +## Compile firmware + +You can build the default layout firwmare for Elongate after setting up your build environment by using: + + make acheron/elongate/beta:default + +After entering DFU state in your PCB, you can download the binary file generated through `dfu-util` or a GUI like QMK Toolbox. + +To directly flash the PCB after it is put into a DFU state, use + + make acheron/elongate/beta:default:flash + +See the [build environment setup](https://docs.qmk.fm/#/getting_started_build_tools) and the [make instructions](https://docs.qmk.fm/#/getting_started_make_guide) for more information. Brand new to QMK? Start with our [Complete Newbs Guide](https://docs.qmk.fm/#/newbs). + +## PCB Documentation + +See the [AcheronDocs](https://acheronproject.com/pcbs/elongate/) page for the ElongatePCB full documentation. You can also check the KiCad PCB files at the [Elongate GitHub repository](https://github.com/AcheronProject/Elongate). + +Before using the files for personal or commercial use, please read the [Acheron Open-Hardware License V1.4](https://acheronproject.com/AOHL14/) under which the Elongate PCB is published. -- cgit v1.2.3