| Commit message (Collapse) | Author | Age | Files | Lines |
|---|
| | |
|
| | |
|
| | |
|
| | |
|
| | |
|
| | |
|
| |
|
| |
Co-authored-by: Nick Brassel <nick@tzarc.org>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
* Draft implementation
* formatting
* fix combined buttons
* remove pimoroni throttle
* sync pointing on a throttle loop with checksum
* no longer used
* doh
Co-authored-by: Drashna Jaelre <drashna@live.com>
* switch pimoroni to a cpi equivalent
* add cpi support
* allow user modification of seperate mouse reports
* a little tidy up
* add *_RIGHT defines.
* docs
* doxygen comments
* basic changelog
* clean up pimoroni
* small doc fixes
* Update docs/feature_pointing_device.md
Co-authored-by: Drashna Jaelre <drashna@live.com>
* performance tweak if side has usb
* Don't run init funtions on wrong side
* renamed some variables for consistency
* fix pimoroni typos
* Clamp instead of OR
* Promote combined values to uint16_t
* Update pointing_device.c
Co-authored-by: Drashna Jaelre <drashna@live.com>
Co-authored-by: Nick Brassel <nick@tzarc.org>
|
| | |
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
* add docs
* core changes
* update keyboards to new OLED
* updated users to new OLED
* update layouts to new OLED
* fixup docs
* drashna's suggestion
* fix up docs
* new keyboards with oled
* core split changes
* remaining keyboard files
* Fix The Helix keyboards oled options
* reflect develop
Co-authored-by: Drashna Jaelre <drashna@live.com>
Co-authored-by: mtei <2170248+mtei@users.noreply.github.com>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
* Make solo half of split keyboards (more) usable.
Using only one half of a split keyboard (that's using the split_common
framework to communicate) is not a great experience, since several read
timeouts per scan cycle cause an unusably slow scan rate.
This change blocks all split communication attempts for 500 ms
(configurable) after an error occurs, causing the scan rate to become at
least _more_ usable, but might need some tweaking to work fully on most
keyboards. One read timeout still needs to occur after the 500 ms has
passed, and if that timeout isn't low enough, some scan cycles may still
be too slow.
* Fix lint complaint.
* Require 25 consecutive comm errors to see comms as disconnected.
The number of max errors can be overridden by defining
`SPLIT_MAX_CONNECTION_ERRORS`.
* Add comments to new defines, and ability to disable disconnection check.
Also increase `SPLIT_MAX_CONNECTION_ERRORS` to 40, since it's divisible
by most relevant numbers for the description.
* Make lint happy ...again
* Only update `connection_check_timer` when needed.
* Add new defines to split keyboard documentation.
* Move connection timeout logic to transport.c, add `is_transport_connected`.
* Use split_common disconnection logic in matrix.c.
Instead of doing more or less the same thing twice.
* Move disconnection logic to `transport_master`.
Is a cleaner implementation, and causes the scan rate while disconnected
to increase instead of decrease.
* Lint fixes.
* Lower default `SERIAL_USART_TIMEOUT` to 20 ms.
The read timeout must be low enough to not cause exessively long scan
cycles when using a solo split half. 10 ms was determined from testing
to work fine even with the slowest defined baudrate of 19200 (5 ms was
too low for that case), so 20 ms should be fine for most cases.
* Remove `SERIAL_USART_TIMEOUT` from ergodox_infinity/config.h
Was somewhat mistakenly included in an earlier PR.
* Fix building with `USE_I2C`.
* Reduce built firmware size.
Not really sure why this works, the idea was taken from tzarc's work on
split disconnection.
* Tweak and improve opt-out for split disconnection logic.
There are now two ways to opt out from this feature:
* Set `SPLIT_MAX_CONNECTION_ERRORS` to 0. This will completely disable
the connection status checks (also affects the slave matrix reset logic in
matrix.c, though).
* Set `SPLIT_CONNECTION_CHECK_TIMEOUT` to 0. This will only disable the
communication throttling while disconnected. Will make the firmware
smaller.
* Make split disconnection logic work with custom transports.
Includes a fallback implementation for keyboards using a custom
split_util.c but not a custom matrix.c (currently no such keyboard seems
to be merged, though).
* Remove unnecessary include of timer.h
Co-authored-by: Joel Challis <git@zvecr.com>
Co-authored-by: Joel Challis <git@zvecr.com>
|
| | |
|
| |
|
|
|
|
|
|
|
| |
* Enable sync of OLED/ST7565 display on/off state on Splits
* Only send if states are not matched
Co-authored-by: Nick Brassel <nick@tzarc.org>
Co-authored-by: Nick Brassel <nick@tzarc.org>
|
| | |
|
|
|
* Extensible split data sync capability through transactions.
- Split common transport has been split up between the transport layer
and data layer.
- Split "transactions" model used, with convergence between I2C and
serial data definitions.
- Slave matrix "generation count" is used to determine if the full slave
matrix needs to be retrieved.
- Encoders get the same "generation count" treatment.
- All other blocks of data are synchronised when a change is detected.
- All transmissions have a globally-configurable deadline before a
transmission is forced (`FORCED_SYNC_THROTTLE_MS`, default 100ms).
- Added atomicity for all core-synced data, preventing partial updates
- Added retries to AVR i2c_master's i2c_start, to minimise the number of
failed transactions when interrupts are disabled on the slave due to
atomicity checks.
- Some keyboards have had slight modifications made in order to ensure
that they still build due to firmware size restrictions.
* Fixup LED_MATRIX compile.
* Parameterise ERROR_DISCONNECT_COUNT.
|
