diff options
Diffstat (limited to 'readme.md')
| -rw-r--r-- | readme.md | 77 |
1 files changed, 67 insertions, 10 deletions
@@ -35,7 +35,7 @@ This is not a tiny project. While this is the main readme, there are many other * The list of possible keycodes you can use in your keymap is actually spread out in a few different places: * [doc/keycode.txt](doc/keycode.txt) - an explanation of those same keycodes. * [quantum/keymap.h](quantum/keymap.h) - this is where the QMK-specific aliases are all set up. Things like the Hyper and Meh key, the Leader key, and all of the other QMK innovations. These are also explained and documented below, but `keymap.h` is where they're actually defined. -* The [TMK documentation](doc/TMK_readme.md). QMK is based on TMK, and this explains how it works internally. +* The [TMK documentation](doc/TMK_README.md). QMK is based on TMK, and this explains how it works internally. # Getting started @@ -75,8 +75,23 @@ Debian/Ubuntu example: sudo apt-get update sudo apt-get install gcc-avr avr-libc dfu-programmer +### Docker + +If this is a bit complex for you, Docker might be the turn-key solution you need. After installing [Docker](https://www.docker.com/products/docker), run the following command at the root of the QMK folder to build a keyboard/keymap: + +```bash +# You'll run this every time you want to build a keymap +# modify the keymap and keyboard assigment to compile what you want +# defaults are ergodox_ez/default + +docker run -e keymap=gwen -e keyboard=ergodox_ez --rm -v $('pwd'):/qmk:rw edasque/qmk_firmware + +``` + +This will compile the targetted keyboard/keymap and leave it in your QMK directory for you to flash. + ### Vagrant -If you have any problems building the firmware, you can try using a tool called Vagrant. It will set up a virtual computer with a known configuration that's ready-to-go for firmware building. OLKB does NOT host the files for this virtual computer. Details on how to set up Vagrant are in the [VAGRANT_GUIDE file](VAGRANT_GUIDE.md). +If you have any problems building the firmware, you can try using a tool called Vagrant. It will set up a virtual computer with a known configuration that's ready-to-go for firmware building. OLKB does NOT host the files for this virtual computer. Details on how to set up Vagrant are in the [VAGRANT_GUIDE file](doc/VAGRANT_GUIDE.md). ## Verify Your Installation 1. If you haven't already, obtain this repository ([https://github.com/jackhumbert/qmk_firmware](https://github.com/jackhumbert/qmk_firmware)). You can either download it as a zip file and extract it, or clone it using the command line tool git or the Github Desktop application. @@ -97,7 +112,7 @@ In every keymap folder, the following files are recommended: The `make` command is how you compile the firmware into a .hex file, which can be loaded by a dfu programmer (like dfu-progammer via `make dfu`) or the [Teensy loader](https://www.pjrc.com/teensy/loader.html) (only used with Teensys). You can run `make` from the root (`/`), your keyboard folder (`/keyboards/<keyboard>/`), or your keymap folder (`/keyboards/<keyboard>/keymaps/<keymap>/`) if you have a `Makefile` there (see the example [here](/doc/keymap_makefile_example.mk)). -By default, this will generate a `<keyboard>_<keymap>.hex` file in whichever folder you run `make` from. These files are ignored by git, so don't worry about deleting them when committing/creating pull requests. Your .hex file will also be available on qmk.fm/keyboards/<keyboard>/keymaps/<keymap>/. +By default, this will generate a `<keyboard>_<keymap>.hex` file in whichever folder you run `make` from. These files are ignored by git, so don't worry about deleting them when committing/creating pull requests. Below are some definitions that will be useful: @@ -152,7 +167,7 @@ This allows you to use the system and audio control key codes. `CONSOLE_ENABLE` -TODO +This allows you to print messages that can be read using [`hid_listen`](https://www.pjrc.com/teensy/hid_listen.html). Add this to your `Makefile`, and set it to `yes`. Then put `println`, `printf`, etc. in your keymap or anywhere in the `qmk` source. Finally, open `hid_listen` and enjoy looking at your printed messages. `COMMAND_ENABLE` @@ -372,10 +387,11 @@ But lets start with how to use it, first! First, you will need `TAP_DANCE_ENABLE=yes` in your `Makefile`, because the feature is disabled by default. This adds a little less than 1k to the firmware size. Next, you will want to define some tap-dance keys, which is easiest to do with the `TD()` macro, that - similar to `F()`, takes a number, which will later be used as an index into the `tap_dance_actions` array. -This array specifies what actions shall be taken when a tap-dance key is in action. Currently, there are two possible options: +This array specifies what actions shall be taken when a tap-dance key is in action. Currently, there are three possible options: * `ACTION_TAP_DANCE_DOUBLE(kc1, kc2)`: Sends the `kc1` keycode when tapped once, `kc2` otherwise. -* `ACTION_TAP_DANCE_FN(fn)`: Calls the specified function - defined in the user keymap - with the current state of the tap-dance action. +* `ACTION_TAP_DANCE_FN(fn)`: Calls the specified function - defined in the user keymap - with the final tap count of the tap dance action. +* `ACTION_TAP_DANCE_FN_ADVANCED(on_each_tap_fn, on_dance_finished_fn, on_reset_fn)`: Calls the first specified function - defined in the user keymap - on every tap, the second function on when the dance action finishes (like the previous option), and the last function when the tap dance action resets. The first option is enough for a lot of cases, that just want dual roles. For example, `ACTION_TAP_DANCE(KC_SPC, KC_ENT)` will result in `Space` being sent on single-tap, `Enter` otherwise. @@ -399,7 +415,8 @@ In the end, let's see a full example! enum { CT_SE = 0, CT_CLN, - CT_EGG + CT_EGG, + CT_FLSH, }; /* Have the above three on the keymap, TD(CT_SE), etc... */ @@ -424,10 +441,50 @@ void dance_egg (qk_tap_dance_state_t *state) { } } +// on each tap, light up one led, from right to left +// on the forth tap, turn them off from right to left +void dance_flsh_each(qk_tap_dance_state_t *state) { + switch (state->count) { + case 1: + ergodox_right_led_3_on(); + break; + case 2: + ergodox_right_led_2_on(); + break; + case 3: + ergodox_right_led_1_on(); + break; + case 4: + ergodox_right_led_3_off(); + _delay_ms(50); + ergodox_right_led_2_off(); + _delay_ms(50); + ergodox_right_led_1_off(); + } +} + +// on the fourth tap, set the keyboard on flash state +void dance_flsh_finished(qk_tap_dance_state_t *state) { + if (state->count >= 4) { + reset_keyboard(); + reset_tap_dance(state); + } +} + +// if the flash state didnt happen, then turn off leds, left to right +void dance_flsh_reset(qk_tap_dance_state_t *state) { + ergodox_right_led_1_off(); + _delay_ms(50); + ergodox_right_led_2_off(); + _delay_ms(50); + ergodox_right_led_3_off(); +} + const qk_tap_dance_action_t tap_dance_actions[] = { [CT_SE] = ACTION_TAP_DANCE_DOUBLE (KC_SPC, KC_ENT) ,[CT_CLN] = ACTION_TAP_DANCE_FN (dance_cln) ,[CT_EGG] = ACTION_TAP_DANCE_FN (dance_egg) + ,[CT_FLSH] = ACTION_TAP_DANCE_FN_ADVANCED (dance_flsh_each, dance_flsh_finished, dance_flsh_reset) }; ``` @@ -732,7 +789,7 @@ float music_scale[][2] = SONG(MUSIC_SCALE_SOUND); float goodbye[][2] = SONG(GOODBYE_SOUND); ``` -Wherein we bind predefined songs (from [audio/song_list.h](/audio/song_list.h)) into named variables. This is one optimization that helps save on memory: These songs only take up memory when you reference them in your keymap, because they're essentially all preprocessor directives. +Wherein we bind predefined songs (from [quantum/audio/song_list.h](/quantum/audio/song_list.h)) into named variables. This is one optimization that helps save on memory: These songs only take up memory when you reference them in your keymap, because they're essentially all preprocessor directives. So now you have something called `tone_plover` for example. How do you make it play the Plover tune, then? If you look further down the keymap, you'll see this: @@ -774,7 +831,7 @@ AutoHotkey inserts the Text right of `Send, ` when this combination is pressed. ## RGB Under Glow Mod - + Here is a quick demo on Youtube (with NPKC KC60) (https://www.youtube.com/watch?v=VKrpPAHlisY). @@ -799,7 +856,7 @@ The firmware supports 5 different light effects, and the color (hue, saturation, ### WS2812 Wiring - + Please note the USB port can only supply a limited amount of power to the keyboard (500mA by standard, however, modern computer and most usb hubs can provide 700+mA.). According to the data of NeoPixel from Adafruit, 30 WS2812 LEDs require a 5V 1A power supply, LEDs used in this mod should not more than 20. |