diff options
Diffstat (limited to 'protocol/iwrap/suart.S')
| -rw-r--r-- | protocol/iwrap/suart.S | 156 |
1 files changed, 0 insertions, 156 deletions
diff --git a/protocol/iwrap/suart.S b/protocol/iwrap/suart.S deleted file mode 100644 index 1b02909638..0000000000 --- a/protocol/iwrap/suart.S +++ /dev/null @@ -1,156 +0,0 @@ -;---------------------------------------------------------------------------;
-; Software implemented UART module ;
-; (C)ChaN, 2005 (http://elm-chan.org/) ;
-;---------------------------------------------------------------------------;
-; Bit rate settings:
-;
-; 1MHz 2MHz 4MHz 6MHz 8MHz 10MHz 12MHz 16MHz 20MHz
-; 2.4kbps 138 - - - - - - - -
-; 4.8kbps 68 138 - - - - - - -
-; 9.6kbps 33 68 138 208 - - - - -
-; 19.2kbps - 33 68 102 138 173 208 - -
-; 38.4kbps - - 33 50 68 85 102 138 172
-; 57.6kbps - - 21 33 44 56 68 91 114
-; 115.2kbps - - - - 21 27 33 44 56
-
-.nolist
-#include <avr/io.h>
-.list
-
-#define BPS 102 /* Bit delay. (see above table) */
-#define BIDIR 0 /* 0:Separated Tx/Rx, 1:Shared Tx/Rx */
-
-#define OUT_1 sbi _SFR_IO_ADDR(SUART_OUT_PORT), SUART_OUT_BIT /* Output 1 */
-#define OUT_0 cbi _SFR_IO_ADDR(SUART_OUT_PORT), SUART_OUT_BIT /* Output 0 */
-#define SKIP_IN_1 sbis _SFR_IO_ADDR(SUART_IN_PIN), SUART_IN_BIT /* Skip if 1 */
-#define SKIP_IN_0 sbic _SFR_IO_ADDR(SUART_IN_PIN), SUART_IN_BIT /* Skip if 0 */
-
-
-
-#ifdef SPM_PAGESIZE
-.macro _LPMI reg
- lpm \reg, Z+
-.endm
-.macro _MOVW dh,dl, sh,sl
- movw \dl, \sl
-.endm
-#else
-.macro _LPMI reg
- lpm
- mov \reg, r0
- adiw ZL, 1
-.endm
-.macro _MOVW dh,dl, sh,sl
- mov \dl, \sl
- mov \dh, \sh
-.endm
-#endif
-
-
-
-;---------------------------------------------------------------------------;
-; Transmit a byte in serial format of N81
-;
-;Prototype: void xmit (uint8_t data);
-;Size: 16 words
-
-.global xmit
-.func xmit
-xmit:
-#if BIDIR
- ldi r23, BPS-1 ;Pre-idle time for bidirectional data line
-5: dec r23 ;
- brne 5b ;/
-#endif
- in r0, _SFR_IO_ADDR(SREG) ;Save flags
-
- com r24 ;C = start bit
- ldi r25, 10 ;Bit counter
- cli ;Start critical section
-
-1: ldi r23, BPS-1 ;----- Bit transferring loop
-2: dec r23 ;Wait for a bit time
- brne 2b ;/
- brcs 3f ;MISO = bit to be sent
- OUT_1 ;
-3: brcc 4f ;
- OUT_0 ;/
-4: lsr r24 ;Get next bit into C
- dec r25 ;All bits sent?
- brne 1b ; no, coutinue
-
- out _SFR_IO_ADDR(SREG), r0 ;End of critical section
- ret
-.endfunc
-
-
-
-;---------------------------------------------------------------------------;
-; Receive a byte
-;
-;Prototype: uint8_t rcvr (void);
-;Size: 19 words
-
-.global rcvr
-.func rcvr
-rcvr:
- in r0, _SFR_IO_ADDR(SREG) ;Save flags
-
- ldi r24, 0x80 ;Receiving shift reg
- cli ;Start critical section
-
-1: SKIP_IN_1 ;Wait for idle
- rjmp 1b
-2: SKIP_IN_0 ;Wait for start bit
- rjmp 2b
- ldi r25, BPS/2 ;Wait for half bit time
-3: dec r25
- brne 3b
-
-4: ldi r25, BPS ;----- Bit receiving loop
-5: dec r25 ;Wait for a bit time
- brne 5b ;/
- lsr r24 ;Next bit
- SKIP_IN_0 ;Get a data bit into r24.7
- ori r24, 0x80
- brcc 4b ;All bits received? no, continue
-
- out _SFR_IO_ADDR(SREG), r0 ;End of critical section
- ret
-.endfunc
-
-
-; Not wait for start bit. This should be called after detecting start bit.
-.global recv
-.func recv
-recv:
- in r0, _SFR_IO_ADDR(SREG) ;Save flags
-
- ldi r24, 0x80 ;Receiving shift reg
- cli ;Start critical section
-
-;1: SKIP_IN_1 ;Wait for idle
-; rjmp 1b
-;2: SKIP_IN_0 ;Wait for start bit
-; rjmp 2b
- ldi r25, BPS/2 ;Wait for half bit time
-3: dec r25
- brne 3b
-
-4: ldi r25, BPS ;----- Bit receiving loop
-5: dec r25 ;Wait for a bit time
- brne 5b ;/
- lsr r24 ;Next bit
- SKIP_IN_0 ;Get a data bit into r24.7
- ori r24, 0x80
- brcc 4b ;All bits received? no, continue
-
- ldi r25, BPS/2 ;Wait for half bit time
-6: dec r25
- brne 6b
-7: SKIP_IN_1 ;Wait for stop bit
- rjmp 7b
-
- out _SFR_IO_ADDR(SREG), r0 ;End of critical section
- ret
-.endfunc
|