diff options
Diffstat (limited to 'platforms/chibios')
| -rw-r--r-- | platforms/chibios/bootloader.c | 145 | ||||
| -rw-r--r-- | platforms/chibios/bootloaders/gd32v_dfu.c | 39 | ||||
| -rw-r--r-- | platforms/chibios/bootloaders/halfkay.c | 25 | ||||
| -rw-r--r-- | platforms/chibios/bootloaders/kiibohd.c | 32 | ||||
| -rw-r--r-- | platforms/chibios/bootloaders/none.c | 19 | ||||
| -rw-r--r-- | platforms/chibios/bootloaders/stm32_dfu.c | 94 | ||||
| -rw-r--r-- | platforms/chibios/bootloaders/stm32duino.c | 21 | ||||
| -rw-r--r-- | platforms/chibios/bootloaders/tinyuf2.c | 34 | ||||
| -rw-r--r-- | platforms/chibios/drivers/i2c_master.c | 59 | ||||
| -rw-r--r-- | platforms/chibios/drivers/i2c_master.h | 61 | ||||
| -rw-r--r-- | platforms/chibios/gpio.h | 24 |
11 files changed, 330 insertions, 223 deletions
diff --git a/platforms/chibios/bootloader.c b/platforms/chibios/bootloader.c deleted file mode 100644 index 58212948b0..0000000000 --- a/platforms/chibios/bootloader.c +++ /dev/null @@ -1,145 +0,0 @@ -#include "bootloader.h" - -#include <ch.h> -#include <hal.h> -#include "wait.h" - -/* This code should be checked whether it runs correctly on platforms */ -#define SYMVAL(sym) (uint32_t)(((uint8_t *)&(sym)) - ((uint8_t *)0)) -#define BOOTLOADER_MAGIC 0xDEADBEEF -#define MAGIC_ADDR (unsigned long *)(SYMVAL(__ram0_end__) - 4) - -#ifndef STM32_BOOTLOADER_DUAL_BANK -# define STM32_BOOTLOADER_DUAL_BANK FALSE -#endif - -#ifdef BOOTLOADER_TINYUF2 - -# define DBL_TAP_MAGIC 0xf01669ef // From tinyuf2's board_api.h - -// defined by linker script -extern uint32_t _board_dfu_dbl_tap[]; -# define DBL_TAP_REG _board_dfu_dbl_tap[0] - -void bootloader_jump(void) { - DBL_TAP_REG = DBL_TAP_MAGIC; - NVIC_SystemReset(); -} - -void enter_bootloader_mode_if_requested(void) { /* not needed, no two-stage reset */ -} - -#elif STM32_BOOTLOADER_DUAL_BANK - -// Need pin definitions -# include "config_common.h" - -# ifndef STM32_BOOTLOADER_DUAL_BANK_GPIO -# error "No STM32_BOOTLOADER_DUAL_BANK_GPIO defined, don't know which pin to toggle" -# endif - -# ifndef STM32_BOOTLOADER_DUAL_BANK_POLARITY -# define STM32_BOOTLOADER_DUAL_BANK_POLARITY 0 -# endif - -# ifndef STM32_BOOTLOADER_DUAL_BANK_DELAY -# define STM32_BOOTLOADER_DUAL_BANK_DELAY 100000 -# endif - -extern uint32_t __ram0_end__; - -__attribute__((weak)) void bootloader_jump(void) { - // For STM32 MCUs with dual-bank flash, and we're incapable of jumping to the bootloader. The first valid flash - // bank is executed unconditionally after a reset, so it doesn't enter DFU unless BOOT0 is high. Instead, we do - // it with hardware...in this case, we pull a GPIO high/low depending on the configuration, connects 3.3V to - // BOOT0's RC charging circuit, lets it charge the capacitor, and issue a system reset. See the QMK discord - // #hardware channel pins for an example circuit. - palSetPadMode(PAL_PORT(STM32_BOOTLOADER_DUAL_BANK_GPIO), PAL_PAD(STM32_BOOTLOADER_DUAL_BANK_GPIO), PAL_MODE_OUTPUT_PUSHPULL); -# if STM32_BOOTLOADER_DUAL_BANK_POLARITY - palSetPad(PAL_PORT(STM32_BOOTLOADER_DUAL_BANK_GPIO), PAL_PAD(STM32_BOOTLOADER_DUAL_BANK_GPIO)); -# else - palClearPad(PAL_PORT(STM32_BOOTLOADER_DUAL_BANK_GPIO), PAL_PAD(STM32_BOOTLOADER_DUAL_BANK_GPIO)); -# endif - - // Wait for a while for the capacitor to charge - wait_ms(100); - - // Issue a system reset to get the ROM bootloader to execute, with BOOT0 high - NVIC_SystemReset(); -} - -void enter_bootloader_mode_if_requested(void) {} // not needed at all, but if anybody attempts to invoke it.... - -#elif defined(STM32_BOOTLOADER_ADDRESS) // STM32_BOOTLOADER_DUAL_BANK - -extern uint32_t __ram0_end__; - -__attribute__((weak)) void bootloader_jump(void) { - *MAGIC_ADDR = BOOTLOADER_MAGIC; // set magic flag => reset handler will jump into boot loader - NVIC_SystemReset(); -} - -void enter_bootloader_mode_if_requested(void) { - unsigned long *check = MAGIC_ADDR; - if (*check == BOOTLOADER_MAGIC) { - *check = 0; - __set_CONTROL(0); - __set_MSP(*(__IO uint32_t *)STM32_BOOTLOADER_ADDRESS); - __enable_irq(); - - typedef void (*BootJump_t)(void); - BootJump_t boot_jump = *(BootJump_t *)(STM32_BOOTLOADER_ADDRESS + 4); - boot_jump(); - while (1) - ; - } -} - -#elif defined(GD32VF103) - -# define DBGMCU_KEY_UNLOCK 0x4B5A6978 -# define DBGMCU_CMD_RESET 0x1 - -__IO uint32_t *DBGMCU_KEY = (uint32_t *)DBGMCU_BASE + 0x0CU; -__IO uint32_t *DBGMCU_CMD = (uint32_t *)DBGMCU_BASE + 0x08U; - -__attribute__((weak)) void bootloader_jump(void) { - /* The MTIMER unit of the GD32VF103 doesn't have the MSFRST - * register to generate a software reset request. - * BUT instead two undocumented registers in the debug peripheral - * that allow issueing a software reset. WHO would need the MSFRST - * register anyway? Source: - * https://github.com/esmil/gd32vf103inator/blob/master/include/gd32vf103/dbg.h */ - *DBGMCU_KEY = DBGMCU_KEY_UNLOCK; - *DBGMCU_CMD = DBGMCU_CMD_RESET; -} - -void enter_bootloader_mode_if_requested(void) { /* Jumping to bootloader is not possible from user code. */ -} - -#elif defined(KL2x) || defined(K20x) || defined(MK66F18) || defined(MIMXRT1062) // STM32_BOOTLOADER_DUAL_BANK // STM32_BOOTLOADER_ADDRESS -/* Kinetis */ - -# if defined(BOOTLOADER_KIIBOHD) -/* Kiibohd Bootloader (MCHCK and Infinity KB) */ -# define SCB_AIRCR_VECTKEY_WRITEMAGIC 0x05FA0000 -const uint8_t sys_reset_to_loader_magic[] = "\xff\x00\x7fRESET TO LOADER\x7f\x00\xff\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00"; -__attribute__((weak)) void bootloader_jump(void) { - void *volatile vbat = (void *)VBAT; - __builtin_memcpy(vbat, (const void *)sys_reset_to_loader_magic, sizeof(sys_reset_to_loader_magic)); - // request reset - SCB->AIRCR = SCB_AIRCR_VECTKEY_WRITEMAGIC | SCB_AIRCR_SYSRESETREQ_Msk; -} - -# else /* defined(BOOTLOADER_KIIBOHD) */ -/* Default for Kinetis - expecting an ARM Teensy */ -# include "wait.h" -__attribute__((weak)) void bootloader_jump(void) { - wait_ms(100); - __BKPT(0); -} -# endif /* defined(BOOTLOADER_KIIBOHD) */ - -#else /* neither STM32 nor KINETIS */ -__attribute__((weak)) void bootloader_jump(void) {} -#endif diff --git a/platforms/chibios/bootloaders/gd32v_dfu.c b/platforms/chibios/bootloaders/gd32v_dfu.c new file mode 100644 index 0000000000..7a979638e3 --- /dev/null +++ b/platforms/chibios/bootloaders/gd32v_dfu.c @@ -0,0 +1,39 @@ +/* Copyright 2021 QMK + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 3 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see <http://www.gnu.org/licenses/>. + */ + +#include "bootloader.h" + +#include <ch.h> + +#define DBGMCU_KEY_UNLOCK 0x4B5A6978 +#define DBGMCU_CMD_RESET 0x1 + +__IO uint32_t *DBGMCU_KEY = (uint32_t *)DBGMCU_BASE + 0x0CU; +__IO uint32_t *DBGMCU_CMD = (uint32_t *)DBGMCU_BASE + 0x08U; + +__attribute__((weak)) void bootloader_jump(void) { + /* The MTIMER unit of the GD32VF103 doesn't have the MSFRST + * register to generate a software reset request. + * BUT instead two undocumented registers in the debug peripheral + * that allow issueing a software reset. WHO would need the MSFRST + * register anyway? Source: + * https://github.com/esmil/gd32vf103inator/blob/master/include/gd32vf103/dbg.h */ + *DBGMCU_KEY = DBGMCU_KEY_UNLOCK; + *DBGMCU_CMD = DBGMCU_CMD_RESET; +} + +/* Jumping to bootloader is not possible from user code. */ +void enter_bootloader_mode_if_requested(void) {} diff --git a/platforms/chibios/bootloaders/halfkay.c b/platforms/chibios/bootloaders/halfkay.c new file mode 100644 index 0000000000..168c2abc23 --- /dev/null +++ b/platforms/chibios/bootloaders/halfkay.c @@ -0,0 +1,25 @@ +/* Copyright 2021 QMK + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 3 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see <http://www.gnu.org/licenses/>. + */ + +#include "bootloader.h" + +#include <ch.h> +#include "wait.h" + +__attribute__((weak)) void bootloader_jump(void) { + wait_ms(100); + __BKPT(0); +} diff --git a/platforms/chibios/bootloaders/kiibohd.c b/platforms/chibios/bootloaders/kiibohd.c new file mode 100644 index 0000000000..911e807092 --- /dev/null +++ b/platforms/chibios/bootloaders/kiibohd.c @@ -0,0 +1,32 @@ +/* Copyright 2021 QMK + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 3 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see <http://www.gnu.org/licenses/>. + */ + +#include "bootloader.h" + +#include <ch.h> + +/* Kiibohd Bootloader (MCHCK and Infinity KB) */ +#define SCB_AIRCR_VECTKEY_WRITEMAGIC 0x05FA0000 + +const uint8_t sys_reset_to_loader_magic[] = "\xff\x00\x7fRESET TO LOADER\x7f\x00\xff\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00"; + +__attribute__((weak)) void bootloader_jump(void) { + void *volatile vbat = (void *)VBAT; + __builtin_memcpy(vbat, (const void *)sys_reset_to_loader_magic, sizeof(sys_reset_to_loader_magic)); + + // request reset + SCB->AIRCR = SCB_AIRCR_VECTKEY_WRITEMAGIC | SCB_AIRCR_SYSRESETREQ_Msk; +} diff --git a/platforms/chibios/bootloaders/none.c b/platforms/chibios/bootloaders/none.c new file mode 100644 index 0000000000..624fbe242a --- /dev/null +++ b/platforms/chibios/bootloaders/none.c @@ -0,0 +1,19 @@ +/* Copyright 2021 QMK + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 3 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see <http://www.gnu.org/licenses/>. + */ + +#include "bootloader.h" + +__attribute__((weak)) void bootloader_jump(void) {} diff --git a/platforms/chibios/bootloaders/stm32_dfu.c b/platforms/chibios/bootloaders/stm32_dfu.c new file mode 100644 index 0000000000..0a113570f7 --- /dev/null +++ b/platforms/chibios/bootloaders/stm32_dfu.c @@ -0,0 +1,94 @@ +/* Copyright 2021 QMK + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 3 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see <http://www.gnu.org/licenses/>. + */ + +#include "bootloader.h" + +#include <ch.h> +#include <hal.h> +#include "wait.h" + +extern uint32_t __ram0_end__; + +#ifndef STM32_BOOTLOADER_DUAL_BANK +# define STM32_BOOTLOADER_DUAL_BANK FALSE +#endif + +#if STM32_BOOTLOADER_DUAL_BANK +# include "config_common.h" + +# ifndef STM32_BOOTLOADER_DUAL_BANK_GPIO +# error "No STM32_BOOTLOADER_DUAL_BANK_GPIO defined, don't know which pin to toggle" +# endif + +# ifndef STM32_BOOTLOADER_DUAL_BANK_POLARITY +# define STM32_BOOTLOADER_DUAL_BANK_POLARITY 0 +# endif + +# ifndef STM32_BOOTLOADER_DUAL_BANK_DELAY +# define STM32_BOOTLOADER_DUAL_BANK_DELAY 100000 +# endif + +__attribute__((weak)) void bootloader_jump(void) { + // For STM32 MCUs with dual-bank flash, and we're incapable of jumping to the bootloader. The first valid flash + // bank is executed unconditionally after a reset, so it doesn't enter DFU unless BOOT0 is high. Instead, we do + // it with hardware...in this case, we pull a GPIO high/low depending on the configuration, connects 3.3V to + // BOOT0's RC charging circuit, lets it charge the capacitor, and issue a system reset. See the QMK discord + // #hardware channel pins for an example circuit. + palSetPadMode(PAL_PORT(STM32_BOOTLOADER_DUAL_BANK_GPIO), PAL_PAD(STM32_BOOTLOADER_DUAL_BANK_GPIO), PAL_MODE_OUTPUT_PUSHPULL); +# if STM32_BOOTLOADER_DUAL_BANK_POLARITY + palSetPad(PAL_PORT(STM32_BOOTLOADER_DUAL_BANK_GPIO), PAL_PAD(STM32_BOOTLOADER_DUAL_BANK_GPIO)); +# else + palClearPad(PAL_PORT(STM32_BOOTLOADER_DUAL_BANK_GPIO), PAL_PAD(STM32_BOOTLOADER_DUAL_BANK_GPIO)); +# endif + + // Wait for a while for the capacitor to charge + wait_ms(100); + + // Issue a system reset to get the ROM bootloader to execute, with BOOT0 high + NVIC_SystemReset(); +} + +// not needed at all, but if anybody attempts to invoke it.... +void enter_bootloader_mode_if_requested(void) {} + +#else + +/* This code should be checked whether it runs correctly on platforms */ +# define SYMVAL(sym) (uint32_t)(((uint8_t *)&(sym)) - ((uint8_t *)0)) +# define BOOTLOADER_MAGIC 0xDEADBEEF +# define MAGIC_ADDR (unsigned long *)(SYMVAL(__ram0_end__) - 4) + +__attribute__((weak)) void bootloader_jump(void) { + *MAGIC_ADDR = BOOTLOADER_MAGIC; // set magic flag => reset handler will jump into boot loader + NVIC_SystemReset(); +} + +void enter_bootloader_mode_if_requested(void) { + unsigned long *check = MAGIC_ADDR; + if (*check == BOOTLOADER_MAGIC) { + *check = 0; + __set_CONTROL(0); + __set_MSP(*(__IO uint32_t *)STM32_BOOTLOADER_ADDRESS); + __enable_irq(); + + typedef void (*BootJump_t)(void); + BootJump_t boot_jump = *(BootJump_t *)(STM32_BOOTLOADER_ADDRESS + 4); + boot_jump(); + while (1) + ; + } +} +#endif diff --git a/platforms/chibios/bootloaders/stm32duino.c b/platforms/chibios/bootloaders/stm32duino.c new file mode 100644 index 0000000000..dd1d551fa9 --- /dev/null +++ b/platforms/chibios/bootloaders/stm32duino.c @@ -0,0 +1,21 @@ +/* Copyright 2021 QMK + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 3 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see <http://www.gnu.org/licenses/>. + */ + +#include "bootloader.h" + +#include <ch.h> + +__attribute__((weak)) void bootloader_jump(void) { NVIC_SystemReset(); } diff --git a/platforms/chibios/bootloaders/tinyuf2.c b/platforms/chibios/bootloaders/tinyuf2.c new file mode 100644 index 0000000000..9ffca5dec8 --- /dev/null +++ b/platforms/chibios/bootloaders/tinyuf2.c @@ -0,0 +1,34 @@ +/* Copyright 2021 QMK + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 3 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see <http://www.gnu.org/licenses/>. + */ + +#include "bootloader.h" + +#include <ch.h> + +// From tinyuf2's board_api.h +#define DBL_TAP_MAGIC 0xF01669EF + +// defined by linker script +extern uint32_t _board_dfu_dbl_tap[]; +#define DBL_TAP_REG _board_dfu_dbl_tap[0] + +__attribute__((weak)) void bootloader_jump(void) { + DBL_TAP_REG = DBL_TAP_MAGIC; + NVIC_SystemReset(); +} + +/* not needed, no two-stage reset */ +void enter_bootloader_mode_if_requested(void) {} diff --git a/platforms/chibios/drivers/i2c_master.c b/platforms/chibios/drivers/i2c_master.c index 43591d56f8..4a5d4760d0 100644 --- a/platforms/chibios/drivers/i2c_master.c +++ b/platforms/chibios/drivers/i2c_master.c @@ -27,8 +27,67 @@ #include "quantum.h" #include "i2c_master.h" #include <string.h> +#include <ch.h> #include <hal.h> +#ifndef I2C1_SCL_PIN +# define I2C1_SCL_PIN B6 +#endif +#ifndef I2C1_SDA_PIN +# define I2C1_SDA_PIN B7 +#endif + +#ifdef USE_I2CV1 +# ifndef I2C1_OPMODE +# define I2C1_OPMODE OPMODE_I2C +# endif +# ifndef I2C1_CLOCK_SPEED +# define I2C1_CLOCK_SPEED 100000 /* 400000 */ +# endif +# ifndef I2C1_DUTY_CYCLE +# define I2C1_DUTY_CYCLE STD_DUTY_CYCLE /* FAST_DUTY_CYCLE_2 */ +# endif +#else +// The default timing values below configures the I2C clock to 400khz assuming a 72Mhz clock +// For more info : https://www.st.com/en/embedded-software/stsw-stm32126.html +# ifndef I2C1_TIMINGR_PRESC +# define I2C1_TIMINGR_PRESC 0U +# endif +# ifndef I2C1_TIMINGR_SCLDEL +# define I2C1_TIMINGR_SCLDEL 7U +# endif +# ifndef I2C1_TIMINGR_SDADEL +# define I2C1_TIMINGR_SDADEL 0U +# endif +# ifndef I2C1_TIMINGR_SCLH +# define I2C1_TIMINGR_SCLH 38U +# endif +# ifndef I2C1_TIMINGR_SCLL +# define I2C1_TIMINGR_SCLL 129U +# endif +#endif + +#ifndef I2C_DRIVER +# define I2C_DRIVER I2CD1 +#endif + +#ifdef USE_GPIOV1 +# ifndef I2C1_SCL_PAL_MODE +# define I2C1_SCL_PAL_MODE PAL_MODE_ALTERNATE_OPENDRAIN +# endif +# ifndef I2C1_SDA_PAL_MODE +# define I2C1_SDA_PAL_MODE PAL_MODE_ALTERNATE_OPENDRAIN +# endif +#else +// The default PAL alternate modes are used to signal that the pins are used for I2C +# ifndef I2C1_SCL_PAL_MODE +# define I2C1_SCL_PAL_MODE 4 +# endif +# ifndef I2C1_SDA_PAL_MODE +# define I2C1_SDA_PAL_MODE 4 +# endif +#endif + static uint8_t i2c_address; static const I2CConfig i2cconfig = { diff --git a/platforms/chibios/drivers/i2c_master.h b/platforms/chibios/drivers/i2c_master.h index 5f082e9d1e..deee7ecc08 100644 --- a/platforms/chibios/drivers/i2c_master.h +++ b/platforms/chibios/drivers/i2c_master.h @@ -24,66 +24,7 @@ */ #pragma once -#include <ch.h> -#include <hal.h> - -#ifndef I2C1_SCL_PIN -# define I2C1_SCL_PIN B6 -#endif -#ifndef I2C1_SDA_PIN -# define I2C1_SDA_PIN B7 -#endif - -#ifdef USE_I2CV1 -# ifndef I2C1_OPMODE -# define I2C1_OPMODE OPMODE_I2C -# endif -# ifndef I2C1_CLOCK_SPEED -# define I2C1_CLOCK_SPEED 100000 /* 400000 */ -# endif -# ifndef I2C1_DUTY_CYCLE -# define I2C1_DUTY_CYCLE STD_DUTY_CYCLE /* FAST_DUTY_CYCLE_2 */ -# endif -#else -// The default timing values below configures the I2C clock to 400khz assuming a 72Mhz clock -// For more info : https://www.st.com/en/embedded-software/stsw-stm32126.html -# ifndef I2C1_TIMINGR_PRESC -# define I2C1_TIMINGR_PRESC 0U -# endif -# ifndef I2C1_TIMINGR_SCLDEL -# define I2C1_TIMINGR_SCLDEL 7U -# endif -# ifndef I2C1_TIMINGR_SDADEL -# define I2C1_TIMINGR_SDADEL 0U -# endif -# ifndef I2C1_TIMINGR_SCLH -# define I2C1_TIMINGR_SCLH 38U -# endif -# ifndef I2C1_TIMINGR_SCLL -# define I2C1_TIMINGR_SCLL 129U -# endif -#endif - -#ifndef I2C_DRIVER -# define I2C_DRIVER I2CD1 -#endif - -#ifdef USE_GPIOV1 -# ifndef I2C1_SCL_PAL_MODE -# define I2C1_SCL_PAL_MODE PAL_MODE_ALTERNATE_OPENDRAIN -# endif -# ifndef I2C1_SDA_PAL_MODE -# define I2C1_SDA_PAL_MODE PAL_MODE_ALTERNATE_OPENDRAIN -# endif -#else -// The default PAL alternate modes are used to signal that the pins are used for I2C -# ifndef I2C1_SCL_PAL_MODE -# define I2C1_SCL_PAL_MODE 4 -# endif -# ifndef I2C1_SDA_PAL_MODE -# define I2C1_SDA_PAL_MODE 4 -# endif -#endif +#include <stdint.h> typedef int16_t i2c_status_t; diff --git a/platforms/chibios/gpio.h b/platforms/chibios/gpio.h index 4d057f1cab..eb44a18f9c 100644 --- a/platforms/chibios/gpio.h +++ b/platforms/chibios/gpio.h @@ -22,10 +22,12 @@ typedef ioline_t pin_t; /* Operation of GPIO by pin. */ -#define setPinInput(pin) palSetLineMode(pin, PAL_MODE_INPUT) -#define setPinInputHigh(pin) palSetLineMode(pin, PAL_MODE_INPUT_PULLUP) -#define setPinInputLow(pin) palSetLineMode(pin, PAL_MODE_INPUT_PULLDOWN) -#define setPinOutput(pin) palSetLineMode(pin, PAL_MODE_OUTPUT_PUSHPULL) +#define setPinInput(pin) palSetLineMode((pin), PAL_MODE_INPUT) +#define setPinInputHigh(pin) palSetLineMode((pin), PAL_MODE_INPUT_PULLUP) +#define setPinInputLow(pin) palSetLineMode((pin), PAL_MODE_INPUT_PULLDOWN) +#define setPinOutputPushPull(pin) palSetLineMode((pin), PAL_MODE_OUTPUT_PUSHPULL) +#define setPinOutputOpenDrain(pin) palSetLineMode((pin), PAL_MODE_OUTPUT_OPENDRAIN) +#define setPinOutput(pin) setPinOutputPushPull(pin) #define writePinHigh(pin) palSetLine(pin) #define writePinLow(pin) palClearLine(pin) @@ -34,17 +36,3 @@ typedef ioline_t pin_t; #define readPin(pin) palReadLine(pin) #define togglePin(pin) palToggleLine(pin) - -/* Operation of GPIO by port. */ - -typedef uint16_t port_data_t; - -#define readPort(pin) palReadPort(PAL_PORT(pin)) - -#define setPortBitInput(pin, bit) palSetPadMode(PAL_PORT(pin), bit, PAL_MODE_INPUT) -#define setPortBitInputHigh(pin, bit) palSetPadMode(PAL_PORT(pin), bit, PAL_MODE_INPUT_PULLUP) -#define setPortBitInputLow(pin, bit) palSetPadMode(PAL_PORT(pin), bit, PAL_MODE_INPUT_PULLDOWN) -#define setPortBitOutput(pin, bit) palSetPadMode(PAL_PORT(pin), bit, PAL_MODE_OUTPUT_PUSHPULL) - -#define writePortBitLow(pin, bit) palClearLine(PAL_LINE(PAL_PORT(pin), bit)) -#define writePortBitHigh(pin, bit) palSetLine(PAL_LINE(PAL_PORT(pin), bit)) |