1 files changed, 8 insertions, 38 deletions

diff --git a/platforms/avr/drivers/serial.c b/platforms/avr/drivers/serial.c
index 9a7345a53d..62908e5875 100644
--- a/platforms/avr/drivers/serial.c
+++ b/platforms/avr/drivers/serial.c
@@ -16,6 +16,7 @@
 #include <util/delay.h>
 #include <stddef.h>
 #include <stdbool.h>
+#include "gpio.h"
 #include "serial.h"
 
 #ifdef SOFT_SERIAL_PIN
@@ -119,12 +120,6 @@
 #        error invalid SOFT_SERIAL_PIN value
 #    endif
 
-#    define setPinInputHigh(pin) (DDRx_ADDRESS(pin) &= ~_BV((pin)&0xF), PORTx_ADDRESS(pin) |= _BV((pin)&0xF))
-#    define setPinOutput(pin) (DDRx_ADDRESS(pin) |= _BV((pin)&0xF))
-#    define writePinHigh(pin) (PORTx_ADDRESS(pin) |= _BV((pin)&0xF))
-#    define writePinLow(pin) (PORTx_ADDRESS(pin) &= ~_BV((pin)&0xF))
-#    define readPin(pin) ((bool)(PINx_ADDRESS(pin) & _BV((pin)&0xF)))
-
 #    define ALWAYS_INLINE __attribute__((always_inline))
 #    define NO_INLINE __attribute__((noinline))
 #    define _delay_sub_us(x) __builtin_avr_delay_cycles(x)
@@ -414,13 +409,7 @@ ISR(SERIAL_PIN_INTERRUPT) {
 
     // target recive phase
     if (trans->initiator2target_buffer_size > 0) {
-        if (serial_recive_packet((uint8_t *)split_trans_initiator2target_buffer(trans), trans->initiator2target_buffer_size)) {
-            *trans->status = TRANSACTION_ACCEPTED;
-        } else {
-            *trans->status = TRANSACTION_DATA_ERROR;
-        }
-    } else {
-        *trans->status = TRANSACTION_ACCEPTED;
+        serial_recive_packet((uint8_t *)split_trans_initiator2target_buffer(trans), trans->initiator2target_buffer_size);
     }
 
     sync_recv();  // weit initiator output to high
@@ -429,19 +418,13 @@ ISR(SERIAL_PIN_INTERRUPT) {
 /////////
 //  start transaction by initiator
 //
-// int  soft_serial_transaction(int sstd_index)
+// bool  soft_serial_transaction(int sstd_index)
 //
-// Returns:
-//    TRANSACTION_END
-//    TRANSACTION_NO_RESPONSE
-//    TRANSACTION_DATA_ERROR
 // this code is very time dependent, so we need to disable interrupts
-int soft_serial_transaction(int sstd_index) {
-    if (sstd_index > NUM_TOTAL_TRANSACTIONS) return TRANSACTION_TYPE_ERROR;
+bool soft_serial_transaction(int sstd_index) {
+    if (sstd_index > NUM_TOTAL_TRANSACTIONS) return false;
     split_transaction_desc_t *trans = &split_transaction_table[sstd_index];
 
-    if (!trans->status) return TRANSACTION_TYPE_ERROR;  // not registered
-
     cli();
 
     // signal to the target that we want to start a transaction
@@ -468,9 +451,8 @@ int soft_serial_transaction(int sstd_index) {
             // slave failed to pull the line low, assume not present
             serial_output();
             serial_high();
-            *trans->status = TRANSACTION_NO_RESPONSE;
             sei();
-            return TRANSACTION_NO_RESPONSE;
+            return false;
         }
         _delay_sub_us(SLAVE_INT_ACK_WIDTH_UNIT);
     }
@@ -481,9 +463,8 @@ int soft_serial_transaction(int sstd_index) {
         if (!serial_recive_packet((uint8_t *)split_trans_target2initiator_buffer(trans), trans->target2initiator_buffer_size)) {
             serial_output();
             serial_high();
-            *trans->status = TRANSACTION_DATA_ERROR;
             sei();
-            return TRANSACTION_DATA_ERROR;
+            return false;
         }
     }
 
@@ -498,19 +479,8 @@ int soft_serial_transaction(int sstd_index) {
     // always, release the line when not in use
     sync_send();
 
-    *trans->status = TRANSACTION_END;
-    sei();
-    return TRANSACTION_END;
-}
-
-int soft_serial_get_and_clean_status(int sstd_index) {
-    split_transaction_desc_t *trans = &split_transaction_table[sstd_index];
-    cli();
-    int retval     = *trans->status;
-    *trans->status = 0;
-    ;
     sei();
-    return retval;
+    return true;
 }
 #endif