summaryrefslogtreecommitdiffstats
path: root/platforms/avr/bootloader.c
diff options
context:
space:
mode:
Diffstat (limited to 'platforms/avr/bootloader.c')
-rw-r--r--platforms/avr/bootloader.c293
1 files changed, 293 insertions, 0 deletions
diff --git a/platforms/avr/bootloader.c b/platforms/avr/bootloader.c
new file mode 100644
index 0000000000..c0272903b8
--- /dev/null
+++ b/platforms/avr/bootloader.c
@@ -0,0 +1,293 @@
+#include <stdint.h>
+#include <stdbool.h>
+#include <avr/io.h>
+#include <avr/eeprom.h>
+#include <avr/interrupt.h>
+#include <avr/wdt.h>
+#include <util/delay.h>
+#include "bootloader.h"
+#include <avr/boot.h>
+
+#ifdef PROTOCOL_LUFA
+# include <LUFA/Drivers/USB/USB.h>
+#endif
+
+/** \brief Bootloader Size in *bytes*
+ *
+ * AVR Boot section size are defined by setting BOOTSZ fuse in fact. Consult with your MCU datasheet.
+ * Note that 'Word'(2 bytes) size and address are used in datasheet while TMK uses 'Byte'.
+ *
+ * Size of Bootloaders in bytes:
+ * Atmel DFU loader(ATmega32U4) 4096
+ * Atmel DFU loader(AT90USB128) 8192
+ * LUFA bootloader(ATmega32U4) 4096
+ * Arduino Caterina(ATmega32U4) 4096
+ * USBaspLoader(ATmega***) 2048
+ * Teensy halfKay(ATmega32U4) 512
+ * Teensy++ halfKay(AT90USB128) 1024
+ *
+ * AVR Boot section is located at the end of Flash memory like the followings.
+ *
+ * byte Atmel/LUFA(ATMega32u4) byte Atmel(AT90SUB128)
+ * 0x0000 +---------------+ 0x00000 +---------------+
+ * | | | |
+ * | | | |
+ * | Application | | Application |
+ * | | | |
+ * = = = =
+ * | | 32KB-4KB | | 128KB-8KB
+ * 0x7000 +---------------+ 0x1E000 +---------------+
+ * | Bootloader | 4KB | Bootloader | 8KB
+ * 0x7FFF +---------------+ 0x1FFFF +---------------+
+ *
+ *
+ * byte Teensy(ATMega32u4) byte Teensy++(AT90SUB128)
+ * 0x0000 +---------------+ 0x00000 +---------------+
+ * | | | |
+ * | | | |
+ * | Application | | Application |
+ * | | | |
+ * = = = =
+ * | | 32KB-512B | | 128KB-1KB
+ * 0x7E00 +---------------+ 0x1FC00 +---------------+
+ * | Bootloader | 512B | Bootloader | 1KB
+ * 0x7FFF +---------------+ 0x1FFFF +---------------+
+ */
+#define FLASH_SIZE (FLASHEND + 1L)
+
+#if !defined(BOOTLOADER_SIZE)
+uint16_t bootloader_start;
+#endif
+
+// compatibility between ATMega8 and ATMega88
+#if !defined(MCUCSR)
+# if defined(MCUSR)
+# define MCUCSR MCUSR
+# endif
+#endif
+
+/** \brief Entering the Bootloader via Software
+ *
+ * http://www.fourwalledcubicle.com/files/LUFA/Doc/120730/html/_page__software_bootloader_start.html
+ */
+#define BOOTLOADER_RESET_KEY 0xB007B007
+uint32_t reset_key __attribute__((section(".noinit,\"aw\",@nobits;")));
+
+/** \brief initialize MCU status by watchdog reset
+ *
+ * FIXME: needs doc
+ */
+__attribute__((weak)) void bootloader_jump(void) {
+#if !defined(BOOTLOADER_SIZE)
+ uint8_t high_fuse = boot_lock_fuse_bits_get(GET_HIGH_FUSE_BITS);
+
+ if (high_fuse & ~(FUSE_BOOTSZ0 & FUSE_BOOTSZ1)) {
+ bootloader_start = (FLASH_SIZE - 512) >> 1;
+ } else if (high_fuse & ~(FUSE_BOOTSZ1)) {
+ bootloader_start = (FLASH_SIZE - 1024) >> 1;
+ } else if (high_fuse & ~(FUSE_BOOTSZ0)) {
+ bootloader_start = (FLASH_SIZE - 2048) >> 1;
+ } else {
+ bootloader_start = (FLASH_SIZE - 4096) >> 1;
+ }
+#endif
+
+ // Something like this might work, but it compiled larger than the block above
+ // bootloader_start = FLASH_SIZE - (256 << (~high_fuse & 0b110 >> 1));
+
+#if defined(BOOTLOADER_HALFKAY)
+ // http://www.pjrc.com/teensy/jump_to_bootloader.html
+ cli();
+ // disable watchdog, if enabled (it's not)
+ // disable all peripherals
+ // a shutdown call might make sense here
+ UDCON = 1;
+ USBCON = (1 << FRZCLK); // disable USB
+ UCSR1B = 0;
+ _delay_ms(5);
+# if defined(__AVR_AT90USB162__) // Teensy 1.0
+ EIMSK = 0;
+ PCICR = 0;
+ SPCR = 0;
+ ACSR = 0;
+ EECR = 0;
+ TIMSK0 = 0;
+ TIMSK1 = 0;
+ UCSR1B = 0;
+ DDRB = 0;
+ DDRC = 0;
+ DDRD = 0;
+ PORTB = 0;
+ PORTC = 0;
+ PORTD = 0;
+ asm volatile("jmp 0x3E00");
+# elif defined(__AVR_ATmega32U4__) // Teensy 2.0
+ EIMSK = 0;
+ PCICR = 0;
+ SPCR = 0;
+ ACSR = 0;
+ EECR = 0;
+ ADCSRA = 0;
+ TIMSK0 = 0;
+ TIMSK1 = 0;
+ TIMSK3 = 0;
+ TIMSK4 = 0;
+ UCSR1B = 0;
+ TWCR = 0;
+ DDRB = 0;
+ DDRC = 0;
+ DDRD = 0;
+ DDRE = 0;
+ DDRF = 0;
+ TWCR = 0;
+ PORTB = 0;
+ PORTC = 0;
+ PORTD = 0;
+ PORTE = 0;
+ PORTF = 0;
+ asm volatile("jmp 0x7E00");
+# elif defined(__AVR_AT90USB646__) // Teensy++ 1.0
+ EIMSK = 0;
+ PCICR = 0;
+ SPCR = 0;
+ ACSR = 0;
+ EECR = 0;
+ ADCSRA = 0;
+ TIMSK0 = 0;
+ TIMSK1 = 0;
+ TIMSK2 = 0;
+ TIMSK3 = 0;
+ UCSR1B = 0;
+ TWCR = 0;
+ DDRA = 0;
+ DDRB = 0;
+ DDRC = 0;
+ DDRD = 0;
+ DDRE = 0;
+ DDRF = 0;
+ PORTA = 0;
+ PORTB = 0;
+ PORTC = 0;
+ PORTD = 0;
+ PORTE = 0;
+ PORTF = 0;
+ asm volatile("jmp 0xFC00");
+# elif defined(__AVR_AT90USB1286__) // Teensy++ 2.0
+ EIMSK = 0;
+ PCICR = 0;
+ SPCR = 0;
+ ACSR = 0;
+ EECR = 0;
+ ADCSRA = 0;
+ TIMSK0 = 0;
+ TIMSK1 = 0;
+ TIMSK2 = 0;
+ TIMSK3 = 0;
+ UCSR1B = 0;
+ TWCR = 0;
+ DDRA = 0;
+ DDRB = 0;
+ DDRC = 0;
+ DDRD = 0;
+ DDRE = 0;
+ DDRF = 0;
+ PORTA = 0;
+ PORTB = 0;
+ PORTC = 0;
+ PORTD = 0;
+ PORTE = 0;
+ PORTF = 0;
+ asm volatile("jmp 0x1FC00");
+# endif
+
+#elif defined(BOOTLOADER_CATERINA)
+ // this block may be optional
+ // TODO: figure it out
+
+ uint16_t *const bootKeyPtr = (uint16_t *)0x0800;
+
+ // Value used by Caterina bootloader use to determine whether to run the
+ // sketch or the bootloader programmer.
+ uint16_t bootKey = 0x7777;
+
+ *bootKeyPtr = bootKey;
+
+ // setup watchdog timeout
+ wdt_enable(WDTO_60MS);
+
+ while (1) {
+ } // wait for watchdog timer to trigger
+
+#elif defined(BOOTLOADER_USBASP)
+ // Taken with permission of Stephan Baerwolf from https://github.com/tinyusbboard/API/blob/master/apipage.c
+ wdt_enable(WDTO_15MS);
+ wdt_reset();
+ asm volatile("cli \n\t"
+ "ldi r29 , %[ramendhi] \n\t"
+ "ldi r28 , %[ramendlo] \n\t"
+# if (FLASHEND > 131071)
+ "ldi r18 , %[bootaddrhi] \n\t"
+ "st Y+, r18 \n\t"
+# endif
+ "ldi r18 , %[bootaddrme] \n\t"
+ "st Y+, r18 \n\t"
+ "ldi r18 , %[bootaddrlo] \n\t"
+ "st Y+, r18 \n\t"
+ "out %[mcucsrio], __zero_reg__ \n\t"
+ "bootloader_startup_loop%=: \n\t"
+ "rjmp bootloader_startup_loop%= \n\t"
+ :
+ : [mcucsrio] "I"(_SFR_IO_ADDR(MCUCSR)),
+# if (FLASHEND > 131071)
+ [ramendhi] "M"(((RAMEND - 2) >> 8) & 0xff), [ramendlo] "M"(((RAMEND - 2) >> 0) & 0xff), [bootaddrhi] "M"((((FLASH_SIZE - BOOTLOADER_SIZE) >> 1) >> 16) & 0xff),
+# else
+ [ramendhi] "M"(((RAMEND - 1) >> 8) & 0xff), [ramendlo] "M"(((RAMEND - 1) >> 0) & 0xff),
+# endif
+ [bootaddrme] "M"((((FLASH_SIZE - BOOTLOADER_SIZE) >> 1) >> 8) & 0xff), [bootaddrlo] "M"((((FLASH_SIZE - BOOTLOADER_SIZE) >> 1) >> 0) & 0xff));
+
+#else // Assume remaining boards are DFU, even if the flag isn't set
+
+# if !(defined(__AVR_ATmega32A__) || defined(__AVR_ATmega328P__) || defined(__AVR_ATmega328__) || defined(__AVR_ATtiny85__)) // no USB - maybe BOOTLOADER_BOOTLOADHID instead though?
+ UDCON = 1;
+ USBCON = (1 << FRZCLK); // disable USB
+ UCSR1B = 0;
+ _delay_ms(5); // 5 seems to work fine
+# endif
+
+# ifdef BOOTLOADER_BOOTLOADHID
+ // force bootloadHID to stay in bootloader mode, so that it waits
+ // for a new firmware to be flashed
+ eeprom_write_byte((uint8_t *)1, 0x00);
+# endif
+
+ // watchdog reset
+ reset_key = BOOTLOADER_RESET_KEY;
+ wdt_enable(WDTO_250MS);
+ for (;;)
+ ;
+#endif
+}
+
+/* this runs before main() */
+void bootloader_jump_after_watchdog_reset(void) __attribute__((used, naked, section(".init3")));
+void bootloader_jump_after_watchdog_reset(void) {
+#ifndef BOOTLOADER_HALFKAY
+ if ((MCUCSR & (1 << WDRF)) && reset_key == BOOTLOADER_RESET_KEY) {
+ reset_key = 0;
+
+ // My custom USBasploader requires this to come up.
+ MCUCSR = 0;
+
+ // Seems like Teensy halfkay loader requires clearing WDRF and disabling watchdog.
+ MCUCSR &= ~(1 << WDRF);
+ wdt_disable();
+
+// This is compled into 'icall', address should be in word unit, not byte.
+# ifdef BOOTLOADER_SIZE
+ ((void (*)(void))((FLASH_SIZE - BOOTLOADER_SIZE) >> 1))();
+# else
+ asm("ijmp" ::"z"(bootloader_start));
+# endif
+ }
+#endif
+}
generated by cgit v1.2.3 (git 2.25.1) at 2024-11-17 05:33:44 +0000