diff options
Diffstat (limited to 'keyboards')
| -rw-r--r-- | keyboards/jd40/Makefile | 74 | ||||
| -rw-r--r-- | keyboards/jd40/config.h | 79 | ||||
| -rw-r--r-- | keyboards/jd40/jd40.c | 26 | ||||
| -rw-r--r-- | keyboards/jd40/jd40.h | 45 | ||||
| -rw-r--r-- | keyboards/jd40/keymaps/default/keymap.c | 164 | ||||
| -rw-r--r-- | keyboards/jd40/readme.md | 17 | ||||
| -rw-r--r-- | keyboards/jd40/rules.mk | 69 | ||||
| -rw-r--r-- | keyboards/planck/keymaps/bone2planck/config.h | 7 | ||||
| -rw-r--r-- | keyboards/planck/keymaps/bone2planck/keymap.c | 51 | ||||
| -rw-r--r-- | keyboards/planck/keymaps/bone2planck/readme.md | 8 | ||||
| -rw-r--r-- | keyboards/planck/keymaps/callum/keymap.c | 23 | ||||
| -rw-r--r-- | keyboards/planck/keymaps/callum/readme.md | 23 | ||||
| -rw-r--r-- | keyboards/planck/keymaps/jhenahan/Makefile | 25 | ||||
| -rw-r--r-- | keyboards/planck/keymaps/jhenahan/config.h | 9 | ||||
| -rw-r--r-- | keyboards/planck/keymaps/jhenahan/keymap.c | 314 | ||||
| -rw-r--r-- | keyboards/planck/keymaps/jhenahan/readme.md | 41 | ||||
| -rw-r--r-- | keyboards/planck/keymaps/pvc/config.h | 9 | ||||
| -rw-r--r-- | keyboards/planck/keymaps/pvc/keymap.c | 428 |
18 files changed, 1172 insertions, 240 deletions
diff --git a/keyboards/jd40/Makefile b/keyboards/jd40/Makefile new file mode 100644 index 0000000000..242748111c --- /dev/null +++ b/keyboards/jd40/Makefile @@ -0,0 +1,74 @@ + + +# MCU name +#MCU = at90usb1287 +MCU = atmega32u4 + +# Processor frequency. +# This will define a symbol, F_CPU, in all source code files equal to the +# processor frequency in Hz. You can then use this symbol in your source code to +# calculate timings. Do NOT tack on a 'UL' at the end, this will be done +# automatically to create a 32-bit value in your source code. +# +# This will be an integer division of F_USB below, as it is sourced by +# F_USB after it has run through any CPU prescalers. Note that this value +# does not *change* the processor frequency - it should merely be updated to +# reflect the processor speed set externally so that the code can use accurate +# software delays. +F_CPU = 16000000 + + +# +# LUFA specific +# +# Target architecture (see library "Board Types" documentation). +ARCH = AVR8 + +# Input clock frequency. +# This will define a symbol, F_USB, in all source code files equal to the +# input clock frequency (before any prescaling is performed) in Hz. This value may +# differ from F_CPU if prescaling is used on the latter, and is required as the +# raw input clock is fed directly to the PLL sections of the AVR for high speed +# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' +# at the end, this will be done automatically to create a 32-bit value in your +# source code. +# +# If no clock division is performed on the input clock inside the AVR (via the +# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. +F_USB = $(F_CPU) + +# Interrupt driven control endpoint task(+60) +OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT + + +# Boot Section Size in *bytes* +# Teensy halfKay 512 +# Teensy++ halfKay 1024 +# Atmel DFU loader 4096 +# LUFA bootloader 4096 +# USBaspLoader 2048 +OPT_DEFS += -DBOOTLOADER_SIZE=4096 + + +# Build Options +# comment out to disable the options. +# +BOOTMAGIC_ENABLE ?= yes # Virtual DIP switch configuration(+1000) +MOUSEKEY_ENABLE ?= yes # Mouse keys(+4700) +EXTRAKEY_ENABLE ?= yes # Audio control and System control(+450) +# CONSOLE_ENABLE ?= yes # Console for debug(+400) +# COMMAND_ENABLE ?= yes # Commands for debug and configuration +KEYBOARD_LOCK_ENABLE ?= yes # Allow locking of keyboard via magic key +# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE +# SLEEP_LED_ENABLE ?= yes # Breathing sleep LED during USB suspend +NKRO_ENABLE ?= yes # USB Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work +# BACKLIGHT_ENABLE ?= yes # Enable keyboard backlight functionality +# MIDI_ENABLE ?= YES # MIDI controls +# UNICODE_ENABLE ?= YES # Unicode +# BLUETOOTH_ENABLE ?= yes # Enable Bluetooth with the Adafruit EZ-Key HID +RGBLIGHT_ENABLE ?= yes # Enable RGB Underglow + +ifndef QUANTUM_DIR + include ../../Makefile +endif + diff --git a/keyboards/jd40/config.h b/keyboards/jd40/config.h new file mode 100644 index 0000000000..e2594f4b37 --- /dev/null +++ b/keyboards/jd40/config.h @@ -0,0 +1,79 @@ +/* +Copyright 2012 Jun Wako <wakojun@gmail.com> + +This program is free software: you can redistribute it and/or modify +it under the terms of the GNU General Public License as published by +the Free Software Foundation, either version 2 of the License, or +(at your option) any later version. + +This program is distributed in the hope that it will be useful, +but WITHOUT ANY WARRANTY; without even the implied warranty of +MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +GNU General Public License for more details. + +You should have received a copy of the GNU General Public License +along with this program. If not, see <http://www.gnu.org/licenses/>. +*/ + +#ifndef CONFIG_H +#define CONFIG_H + +#include "config_common.h" + +/* USB Device descriptor parameter */ +#define VENDOR_ID 0xFEED +#define PRODUCT_ID 0x6060 +#define DEVICE_VER 0x0001 +#define MANUFACTURER geekhack +#define PRODUCT jd40v2 +#define DESCRIPTION t.m.k. keyboard firmware for JD40 MKII + +/* key matrix size */ +#define MATRIX_ROWS 4 +#define MATRIX_COLS 12 + +/* + * Keyboard Matrix Assignments + * + * Change this to how you wired your keyboard + * COLS: AVR pins used for columns, left to right + * ROWS: AVR pins used for rows, top to bottom + * DIODE_DIRECTION: COL2ROW = COL = Anode (+), ROW = Cathode (-, marked on diode) + * ROW2COL = ROW = Anode (+), COL = Cathode (-, marked on diode) + * +*/ +#define MATRIX_ROW_PINS { F0, F1, F5, B4 } +#define MATRIX_COL_PINS { F4, D7, B5, B6, C6, C7, D4, D6, D5, D0, D1, D2 } +#define UNUSED_PINS + +/* COL2ROW or ROW2COL */ +#define DIODE_DIRECTION COL2ROW + +/* Debounce reduces chatter (unintended double-presses) - set 0 if debouncing is not needed */ +#define DEBOUNCING_DELAY 5 + +/* define if matrix has ghost (lacks anti-ghosting diodes) */ +//#define MATRIX_HAS_GHOST + +/* number of backlight levels */ +#define BACKLIGHT_LEVELS 3 + +/* Mechanical locking support. Use KC_LCAP, KC_LNUM or KC_LSCR instead in keymap */ +#define LOCKING_SUPPORT_ENABLE +/* Locking resynchronize hack */ +#define LOCKING_RESYNC_ENABLE + + +/* key combination for magic key command */ +#define IS_COMMAND() ( \ + keyboard_report->mods == (MOD_BIT(KC_LSHIFT) | MOD_BIT(KC_RSHIFT)) \ +) + +#define RGB_DI_PIN D3 +#define RGBLIGHT_TIMER +#define RGBLED_NUM 12 // Number of LEDs +#define RGBLIGHT_HUE_STEP 8 +#define RGBLIGHT_SAT_STEP 8 +#define RGBLIGHT_VAL_STEP 8 + +#endif diff --git a/keyboards/jd40/jd40.c b/keyboards/jd40/jd40.c new file mode 100644 index 0000000000..fa06356d97 --- /dev/null +++ b/keyboards/jd40/jd40.c @@ -0,0 +1,26 @@ +#include "jd40.h" + +void led_set_kb(uint8_t usb_led) { + // put your keyboard LED indicator (ex: Caps Lock LED) toggling code here + + + // if (usb_led & (1<<USB_LED_CAPS_LOCK)) { + // gh60_caps_led_on(); + // } else { + // gh60_caps_led_off(); + // } + + // if (usb_led & (1<<USB_LED_NUM_LOCK)) { + // gh60_esc_led_on(); + // } else { + // gh60_esc_led_off(); + // } + + // if (usb_led & (1<<USB_LED_SCROLL_LOCK)) { + // gh60_fn_led_on(); + // } else { + // gh60_fn_led_off(); + // } + + led_set_user(usb_led); +} diff --git a/keyboards/jd40/jd40.h b/keyboards/jd40/jd40.h new file mode 100644 index 0000000000..77a1222993 --- /dev/null +++ b/keyboards/jd40/jd40.h @@ -0,0 +1,45 @@ +#ifndef JD40_H +#define JD40_H + +#include "quantum.h" +#include "led.h" + +/* GH60 LEDs + * GPIO pads + * 0 F7 WASD LEDs + * 1 F6 ESC LED + * 2 F5 FN LED + * 3 F4 POKER Arrow LEDs + * B2 Capslock LED + * B0 not connected + */ + + /* +inline void gh60_caps_led_on(void) { DDRB |= (1<<2); PORTB &= ~(1<<2); } +inline void gh60_poker_leds_on(void) { DDRF |= (1<<4); PORTF &= ~(1<<4); } +inline void gh60_fn_led_on(void) { DDRF |= (1<<5); PORTF &= ~(1<<5); } +inline void gh60_esc_led_on(void) { DDRF |= (1<<6); PORTF &= ~(1<<6); } +inline void gh60_wasd_leds_on(void) { DDRF |= (1<<7); PORTF &= ~(1<<7); } + +inline void gh60_caps_led_off(void) { DDRB &= ~(1<<2); PORTB &= ~(1<<2); } +inline void gh60_poker_leds_off(void) { DDRF &= ~(1<<4); PORTF &= ~(1<<4); } +inline void gh60_fn_led_off(void) { DDRF &= ~(1<<5); PORTF &= ~(1<<5); } +inline void gh60_esc_led_off(void) { DDRF &= ~(1<<6); PORTF &= ~(1<<6); } +inline void gh60_wasd_leds_off(void) { DDRF &= ~(1<<7); PORTF &= ~(1<<7); } +*/ + +/* JD40 MKII keymap definition macro + */ +#define KEYMAP( \ + K01, K02, K03, K04, K05, K06, K07, K08, K09, K10, K11, K12, \ + K13, K14, K15, K16, K17, K18, K19, K20, K21, K22, K23, \ + K24, K25, K26, K27, K28, K29, K30, K31, K32, K33, K34, \ + K35, K36, K37, K38, K39, K40, K41, K42, K43, K44 \ +) { \ + { KC_##K01, KC_##K02, KC_##K03, KC_##K04, KC_##K05, KC_##K06, KC_##K07, KC_##K08, KC_##K09, KC_##K10, KC_##K11, KC_##K12 }, \ + { KC_##K13, KC_##K14, KC_##K15, KC_##K16, KC_##K17, KC_##K18, KC_##K19, KC_##K20, KC_##K21, KC_##K22, KC_##K23, KC_NO }, \ + { KC_##K24, KC_##K25, KC_##K26, KC_##K27, KC_##K28, KC_##K29, KC_##K30, KC_##K31, KC_##K32, KC_##K33, KC_##K34, KC_NO }, \ + { KC_##K35, KC_##K36, KC_##K37, KC_##K38, KC_##K39, KC_NO, KC_##K40, KC_##K41, KC_##K42, KC_##K43, KC_##K44, KC_NO } \ +} + +#endif diff --git a/keyboards/jd40/keymaps/default/keymap.c b/keyboards/jd40/keymaps/default/keymap.c new file mode 100644 index 0000000000..79ac146c9e --- /dev/null +++ b/keyboards/jd40/keymaps/default/keymap.c @@ -0,0 +1,164 @@ +#include "jd40.h" +#include "action_layer.h" + +#define _BL 0 +#define _AL 1 +#define _FL 2 +#define _UL 3 + +const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = { + [_BL] = KEYMAP( + F12, Q, W, E, R, T, Y, U, I, O, P, BSPC, + TAB, A, S, D, F, G, H, J, K, L, ENT, + LSFT, Z, X, C, V, B, N, M, COMM, UP, DOT, + LCTL, LGUI, LALT, FN0, SPC, SPC, FN0, LEFT, DOWN, RIGHT ), + + [_AL] = KEYMAP( + GRV, F1, F2, F3, F4, F5, F6, F7, F8, F9, F10, DEL, + CAPS, 1, 2, 3, 4, 5, 6, 7, 8, 9, 0, + TRNS, TRNS, TRNS, TRNS, TRNS, TRNS, TRNS, TRNS, SCLN, PGUP, QUOT, + TRNS, TRNS, TRNS, TRNS, FN3, FN3, TRNS, HOME, PGDN, END ), + + [_FL] = KEYMAP( + TRNS, TRNS, TRNS, TRNS, TRNS, TRNS, TRNS, TRNS, TRNS, TRNS, TRNS, TRNS, + TRNS, TRNS, TRNS, TRNS, TRNS, TRNS, TRNS, TRNS, TRNS, TRNS, TRNS, + TRNS, TRNS, TRNS, TRNS, TRNS, TRNS, TRNS, TRNS, TRNS, TRNS, TRNS, + TRNS, TRNS, TRNS, TRNS, TRNS, TRNS, TRNS, TRNS, TRNS, TRNS ), + + [_UL] = KEYMAP( + TRNS, TRNS, TRNS, TRNS, TRNS, TRNS, TRNS, TRNS, TRNS, TRNS, TRNS, TRNS, + TRNS, FN4, FN5, FN11, FN10, TRNS, TRNS, TRNS, TRNS, TRNS, TRNS, + TRNS, TRNS, TRNS, TRNS, TRNS, TRNS, TRNS, TRNS, TRNS, TRNS, TRNS, + TRNS, TRNS, TRNS, TRNS, TRNS, TRNS, TRNS, TRNS, TRNS, TRNS ), +}; + +enum function_id { + RGBLED_TOGGLE, + RGBLED_STEP_MODE, + RGBLED_INCREASE_HUE, + RGBLED_DECREASE_HUE, + RGBLED_INCREASE_SAT, + RGBLED_DECREASE_SAT, + RGBLED_INCREASE_VAL, + RGBLED_DECREASE_VAL, + SHIFT_ESC, +}; + +const uint16_t PROGMEM fn_actions[] = { + [0] = ACTION_LAYER_MOMENTARY(1), // Momentary Fn overlay + [1] = ACTION_LAYER_TOGGLE(2), // Toggle Arrow Layer overlay + [2] = ACTION_LAYER_TAP_KEY(2, KC_CAPS), // Tap to toggle caps lock and hold to activate function layer + [3] = ACTION_LAYER_TOGGLE(3), // Toggle Underglow Layer overlay + [4] = ACTION_FUNCTION(RGBLED_TOGGLE), //Turn on/off underglow + [5] = ACTION_FUNCTION(RGBLED_STEP_MODE), // Change underglow mode + [6] = ACTION_FUNCTION(RGBLED_INCREASE_HUE), + [7] = ACTION_FUNCTION(RGBLED_DECREASE_HUE), + [8] = ACTION_FUNCTION(RGBLED_INCREASE_SAT), + [9] = ACTION_FUNCTION(RGBLED_DECREASE_SAT), + [10] = ACTION_FUNCTION(RGBLED_INCREASE_VAL), + [11] = ACTION_FUNCTION(RGBLED_DECREASE_VAL), + [12] = ACTION_FUNCTION(SHIFT_ESC), +}; + +const macro_t *action_get_macro(keyrecord_t *record, uint8_t id, uint8_t opt) +{ + // MACRODOWN only works in this function + switch(id) { + case 0: + if (record->event.pressed) { + register_code(KC_RSFT); + } else { + unregister_code(KC_RSFT); + } + break; + } + return MACRO_NONE; +}; + +void matrix_scan_user(void) { + +// Layer LED indicators +// ESC led on when in function layer, WASD cluster leds enabled when on arrow cluster + uint32_t layer = layer_state; + if (layer & (1<<1)) { + //gh60_wasd_leds_on(); + } else { + //gh60_wasd_leds_off(); + } + + if (layer & (1<<2)) { + //gh60_esc_led_on(); + } else { + //gh60_esc_led_off(); + } +}; + +#define MODS_CTRL_MASK (MOD_BIT(KC_LSHIFT)|MOD_BIT(KC_RSHIFT)) + +void action_function(keyrecord_t *record, uint8_t id, uint8_t opt) { + switch (id) { + case RGBLED_TOGGLE: + //led operations + if (record->event.pressed) { + rgblight_toggle(); + } + break; + case RGBLED_INCREASE_HUE: + if (record->event.pressed) { + rgblight_increase_hue(); + } + break; + case RGBLED_DECREASE_HUE: + if (record->event.pressed) { + rgblight_decrease_hue(); + } + break; + case RGBLED_INCREASE_SAT: + if (record->event.pressed) { + rgblight_increase_sat(); + } + break; + case RGBLED_DECREASE_SAT: + if (record->event.pressed) { + rgblight_decrease_sat(); + } + break; + case RGBLED_INCREASE_VAL: + if (record->event.pressed) { + rgblight_increase_val(); + } + break; + case RGBLED_DECREASE_VAL: + if (record->event.pressed) { + rgblight_decrease_val(); + } + break; + case RGBLED_STEP_MODE: + if (record->event.pressed) { + rgblight_step(); + } + break; + static uint8_t shift_esc_shift_mask; + // Shift + ESC = ~ + case SHIFT_ESC: + shift_esc_shift_mask = get_mods()&MODS_CTRL_MASK; + if (record->event.pressed) { + if (shift_esc_shift_mask) { + add_key(KC_GRV); + send_keyboard_report(); + } else { + add_key(KC_ESC); + send_keyboard_report(); + } + } else { + if (shift_esc_shift_mask) { + del_key(KC_GRV); + send_keyboard_report(); + } else { + del_key(KC_ESC); + send_keyboard_report(); + } + } + break; + } +}; diff --git a/keyboards/jd40/readme.md b/keyboards/jd40/readme.md new file mode 100644 index 0000000000..7daa0980eb --- /dev/null +++ b/keyboards/jd40/readme.md @@ -0,0 +1,17 @@ +## jd40 mkii keyboard firmware + + Pins: + MATRIX_ROW_PINS { F0, F1, F5, B4 } + MATRIX_COL_PINS { F4, D7, B5, B6, C6, C7, D4, D6, D5, D0, D1, D2 } + RGB_DI_PIN D3 + +====================== + +## Quantum MK Firmware + +For the full Quantum feature list, see [the parent readme.md](/readme.md). + +## Building + +Download or clone the whole firmware and navigate to the keyboards/jd40 folder. +Once your dev env is setup, you'll be able to type `make` to generate your .hex - you can then use the Amtel Flip to program your .hex file. diff --git a/keyboards/jd40/rules.mk b/keyboards/jd40/rules.mk new file mode 100644 index 0000000000..2f18fdf10d --- /dev/null +++ b/keyboards/jd40/rules.mk @@ -0,0 +1,69 @@ + + +# MCU name +#MCU = at90usb1287 +MCU = atmega32u4 + +# Processor frequency. +# This will define a symbol, F_CPU, in all source code files equal to the +# processor frequency in Hz. You can then use this symbol in your source code to +# calculate timings. Do NOT tack on a 'UL' at the end, this will be done +# automatically to create a 32-bit value in your source code. +# +# This will be an integer division of F_USB below, as it is sourced by +# F_USB after it has run through any CPU prescalers. Note that this value +# does not *change* the processor frequency - it should merely be updated to +# reflect the processor speed set externally so that the code can use accurate +# software delays. +F_CPU = 16000000 + + +# +# LUFA specific +# +# Target architecture (see library "Board Types" documentation). +ARCH = AVR8 + +# Input clock frequency. +# This will define a symbol, F_USB, in all source code files equal to the +# input clock frequency (before any prescaling is performed) in Hz. This value may +# differ from F_CPU if prescaling is used on the latter, and is required as the +# raw input clock is fed directly to the PLL sections of the AVR for high speed +# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' +# at the end, this will be done automatically to create a 32-bit value in your +# source code. +# +# If no clock division is performed on the input clock inside the AVR (via the +# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. +F_USB = $(F_CPU) + +# Interrupt driven control endpoint task(+60) +OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT + + +# Boot Section Size in *bytes* +# Teensy halfKay 512 +# Teensy++ halfKay 1024 +# Atmel DFU loader 4096 +# LUFA bootloader 4096 +# USBaspLoader 2048 +OPT_DEFS += -DBOOTLOADER_SIZE=4096 + + +# Build Options +# comment out to disable the options. +# +BOOTMAGIC_ENABLE ?= yes # Virtual DIP switch configuration(+1000) +MOUSEKEY_ENABLE ?= yes # Mouse keys(+4700) +EXTRAKEY_ENABLE ?= yes # Audio control and System control(+450) +# CONSOLE_ENABLE ?= yes # Console for debug(+400) +# COMMAND_ENABLE ?= yes # Commands for debug and configuration +KEYBOARD_LOCK_ENABLE ?= yes # Allow locking of keyboard via magic key +# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE +# SLEEP_LED_ENABLE ?= yes # Breathing sleep LED during USB suspend +NKRO_ENABLE ?= yes # USB Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work +# BACKLIGHT_ENABLE ?= yes # Enable keyboard backlight functionality +# MIDI_ENABLE ?= YES # MIDI controls +# UNICODE_ENABLE ?= YES # Unicode +# BLUETOOTH_ENABLE ?= yes # Enable Bluetooth with the Adafruit EZ-Key HID +RGBLIGHT_ENABLE ?= yes # Enable RGB Underglow
\ No newline at end of file diff --git a/keyboards/planck/keymaps/bone2planck/config.h b/keyboards/planck/keymaps/bone2planck/config.h new file mode 100644 index 0000000000..60aff6db0d --- /dev/null +++ b/keyboards/planck/keymaps/bone2planck/config.h @@ -0,0 +1,7 @@ +#ifndef CONFIG_USER_H +#define CONFIG_USER_H +#endif + +#include "../../config.h" + +#define PREVENT_STUCK_MODIFIERS
\ No newline at end of file diff --git a/keyboards/planck/keymaps/bone2planck/keymap.c b/keyboards/planck/keymaps/bone2planck/keymap.c index 66cf9386df..69d164b8c7 100644 --- a/keyboards/planck/keymaps/bone2planck/keymap.c +++ b/keyboards/planck/keymaps/bone2planck/keymap.c @@ -4,6 +4,13 @@ #endif #include "keymap_german.h" +// for intellisense, has to be commented for building +/* +#include "..\..\..\..\quantum\keymap_extras\keymap_german.h" +#include "..\..\..\..\quantum\keymap_common.h" +#include "..\..\..\..\tmk_core\common\keycode.h" +*/ + #define _______ KC_TRNS /* This Layout tries to emulate the Bone2 Variant of Neo2, and is intended to be used with a German QWERTZ Softwarelayout. @@ -24,14 +31,14 @@ const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = { * |------+------+------+------+------+------|------+------+------+------+------+------| * | Shift| F | V | Ü | Ä | Ö | Y | Z | , | . | K |Shift | * |------+------+------+------+------+------+------+------+------+------+------+------| -* | GUI | Ctrl | Alt | M4 | M2 | Space | M2 | M4 | | Ctrl | Esc | +* | Ctrl | GUI | Alt | M4 | M2 | Space | M2 | M4 | Alt | Esc | Ctrl | * `-----------------------------------------------------------------------------------' */ [0] = { - { DE_Q, DE_J, DE_D, DE_U, DE_A, DE_X, DE_P, DE_H, DE_L, DE_M, DE_W, DE_SS }, - { LT(1,KC_TAB), DE_C, DE_T, DE_I, DE_E, DE_O, DE_B, DE_N, DE_R, DE_S, DE_G, LT(1,KC_ENT) }, - { KC_LSFT, DE_F, DE_V, DE_UE, DE_AE, DE_OE, DE_Y, DE_Z, DE_COMM, DE_DOT, DE_K, KC_LSFT }, - { KC_LGUI, KC_LCTL, KC_LALT, MO(4), MO(2), KC_SPC, KC_SPC, MO(2), MO(4), KC_NO, KC_RCTL, KC_ESC } + { DE_Q, DE_J, DE_D, DE_U, DE_A, DE_X, DE_P, DE_H, DE_L, DE_M, DE_W, DE_SS }, + { LT(1,KC_TAB), DE_C, DE_T, DE_I, DE_E, DE_O, DE_B, DE_N, DE_R, DE_S, DE_G, LT(1,KC_ENT) }, + { KC_LSFT, DE_F, DE_V, DE_UE, DE_AE, DE_OE, DE_Y, DE_Z, DE_COMM, DE_DOT, DE_K, KC_LSFT }, + { KC_LCTL, KC_RGUI, KC_LALT, MO(4), MO(2), KC_SPC, KC_SPC, MO(2), MO(4), KC_RALT, KC_ESC, KC_RCTL } }, /* M1 Special Characters @@ -43,7 +50,7 @@ very ergonomic placement for coding * |------+------+------+------+------+------|------+------+------+------+------+------| * | Shift| # | $ | | | ~ | € | + | % | " | ' | ; |Shift | * |------+------+------+------+------+------+------+------+------+------+------+------| -* | GUI | Ctrl | Alt | M4 | M2 | Space | M2 | M4 | | Ctrl | Esc | +* | Ctrl | GUI | Alt | M4 | M2 | Space | M2 | M4 | Alt | Esc | Ctrl | * `-----------------------------------------------------------------------------------' */ [1] = { @@ -56,37 +63,37 @@ very ergonomic placement for coding /* Navigation & Number Blocks very easy to get used to & intuituve placement * ,-----------------------------------------------------------------------------------. -* | | PgUp | Bksp | Up | DEL | PgDn | | 7 | 8 | 9 | | | +* | | PgUp | Bksp | Up | DEL | PgDn | | 7 | 8 | 9 | | Ins | * |------+------+------+------+------+-------------+------+------+------+------+------| * | Tab | Home | Lft | Down | Right| End | . | 4 | 5 | 6 | , | Enter| * |------+------+------+------+------+------|------+------+------+------+------+------| -* | Shift| | Tab | Ins | Enter| | 0 | 1 | 2 | 3 | ; |Shift | +* | Shift| | Tab | | Enter| | 0 | 1 | 2 | 3 | ; |Shift | * |------+------+------+------+------+------+------+------+------+------+------+------| -* | GUI | Ctrl | Alt | M3 | M2 | Space | M2 | M3 | | Ctrl | Esc | +* | Ctrl | GUI | Alt | M3 | M2 | Space | M2 | M3 | Alt | Esc | Ctrl | * `-----------------------------------------------------------------------------------' */ [2] = { - { KC_NO, KC_PGUP, KC_BSPC, KC_UP, KC_DEL, KC_PGDN, KC_NO, DE_7, DE_8, DE_9, KC_NO, KC_NO }, + { KC_NO, KC_PGUP, KC_BSPC, KC_UP, KC_DEL, KC_PGDN, KC_NO, DE_7, DE_8, DE_9, KC_NO, KC_INS }, { KC_TAB, KC_HOME, KC_LEFT, KC_DOWN, KC_RGHT, KC_END, DE_DOT, DE_4, DE_5, DE_6, DE_COMM, KC_ENT }, - { _______, KC_NO, KC_TAB, KC_INS, KC_ENT, KC_NO, DE_0, DE_1, DE_2, DE_3, DE_SCLN, _______ }, + { _______, KC_NO, KC_TAB, KC_NO, KC_ENT, KC_NO, DE_0, DE_1, DE_2, DE_3, DE_SCLN, _______ }, { _______, _______, _______, MO(3), _______, _______, _______, _______, MO(3), _______, _______, _______ } }, /* Flipped Navigation & Number Blocks for one handed use accessed by sliding from M2 to M3 with thumb * ,-----------------------------------------------------------------------------------. -* | | | 7 | 8 | 9 | | PgUp | Bksp | Up | DEL | PgDn | | +* | Ins | | 7 | 8 | 9 | | PgUp | Bksp | Up | DEL | PgDn | | * |------+------+------+------+------+-------------+------+------+------+------+------| * | Tab | . | 4 | 5 | 6 | , | Home | Left | Down | Right| End | Enter| * |------+------+------+------+------+------|------+------+------+------+------+------| * | Shift| 0 | 1 | 2 | 3 | ; | | Tab | Ins | Enter| |Shift | * |------+------+------+------+------+------+------+------+------+------+------+------| -* | GUI | Ctrl | Alt | M3 | | Space | | M3 | | Ctrl | Esc | +* | Ctrl | GUI | Alt | M3 | | Space | | M3 | Alt | Esc | Ctrl | * `-----------------------------------------------------------------------------------' */ [3] = { - { KC_NO, KC_NO, DE_7, DE_8, DE_9, KC_NO, KC_PGUP, KC_BSPC, KC_UP, KC_DEL, KC_PGDN, KC_NO }, + { KC_INS, KC_NO, DE_7, DE_8, DE_9, KC_NO, KC_PGUP, KC_BSPC, KC_UP, KC_DEL, KC_PGDN, KC_NO }, { _______, DE_DOT, DE_4, DE_5, DE_6, DE_COMM, KC_HOME, KC_LEFT, KC_DOWN, KC_RGHT, KC_END, _______ }, { _______, DE_0, DE_1, DE_2, DE_3, DE_SCLN, KC_NO, KC_TAB, KC_INS, KC_ENT, KC_NO, _______ }, { _______, _______, _______, _______, KC_NO, _______, _______, KC_NO, _______, _______, _______, _______ } @@ -102,7 +109,7 @@ slide from m4 to m5 to access flipped version * |------+------+------+------+------+------|------+------+------+------+------+------| * | Shift| | Prev | Play | Next | | ² | F1 | F2 | F3 | F10 |Shift | * |------+------+------+------+------+------+------+------+------+------+------+------| -* | GUI | Ctrl | Alt | M4 | M5 | Space | M5 | M4 | | Ctrl | Esc | +* | Ctrl | GUI | Alt | M4 | M5 | Space | M5 | M4 | Alt | Esc | Ctrl | * `-----------------------------------------------------------------------------------' */ [4] = { @@ -115,19 +122,19 @@ slide from m4 to m5 to access flipped version /* flipped Function & Media Keys * ,-----------------------------------------------------------------------------------. -* | | | F7 | F8 | F9 | | | Print|Scroll| Pause| | | +* | | | F7 | F8 | F9 | F12 | | Print|Scroll| Pause| | | * |------+------+------+------+------+-------------+------+------+------+------+------| -* | | ³ | F4 | F5 | F6 | | | Mute | Vol- | Vol+ | | | +* | | ³ | F4 | F5 | F6 | F11 | | Mute | Vol- | Vol+ | | | * |------+------+------+------+------+------|------+------+------+------+------+------| -* | Shift| ² | F1 | F2 | F3 | | | Prev | Play | Next | |Shift | +* | Shift| ² | F1 | F2 | F3 | F10 | | Prev | Play | Next | |Shift | * |------+------+------+------+------+------+------+------+------+------+------+------| -* | GUI | Ctrl | Alt | | M5 | Space | M5 | | | Ctrl | Esc | +* | Ctrl | GUI | Alt | | M5 | Space | M5 | | Alt | Esc | Ctrl | * `-----------------------------------------------------------------------------------' */ [5] = { - { KC_NO, KC_NO, KC_F7, KC_F8, KC_F9, KC_NO, KC_NO, KC_PSCR, KC_SLCK, KC_PAUS, KC_NO, KC_NO }, - { KC_NO, DE_SQ3, KC_F4, KC_F5, KC_F6, KC_NO, KC_NO, KC_MUTE, KC_VOLD, KC_VOLU, KC_NO, KC_NO }, - { _______, DE_SQ2, KC_F1, KC_F2, KC_F3, KC_NO, KC_NO, KC_MPRV, KC_MPLY, KC_MNXT, KC_NO, _______ }, + { KC_NO, KC_NO, KC_F7, KC_F8, KC_F9, KC_F12, KC_NO, KC_PSCR, KC_SLCK, KC_PAUS, KC_NO, KC_NO }, + { KC_NO, DE_SQ3, KC_F4, KC_F5, KC_F6, KC_F11, KC_NO, KC_MUTE, KC_VOLD, KC_VOLU, KC_NO, KC_NO }, + { _______, DE_SQ2, KC_F1, KC_F2, KC_F3, KC_F10, KC_NO, KC_MPRV, KC_MPLY, KC_MNXT, KC_NO, _______ }, { _______, _______, _______, KC_NO, _______, _______, _______, _______, KC_NO, _______, _______, _______ } } }; diff --git a/keyboards/planck/keymaps/bone2planck/readme.md b/keyboards/planck/keymaps/bone2planck/readme.md new file mode 100644 index 0000000000..3c425efddb --- /dev/null +++ b/keyboards/planck/keymaps/bone2planck/readme.md @@ -0,0 +1,8 @@ +check keymap.c to the layers + +This Layout tries to emulate the Bone2 Variant of Neo2, and is intended to be used with a German QWERTZ Softwarelayout. +It has "üäöß" as it is optimized for a mix of German & English. +My favourite features are the placement of the special characters often used for programming right on the home row +and the number & navigation block combo, so you never have to move your hands from their home position. + +Bone2 wiki page: http://wiki.neo-layout.org/wiki/Bone
\ No newline at end of file diff --git a/keyboards/planck/keymaps/callum/keymap.c b/keyboards/planck/keymaps/callum/keymap.c index ed187df1da..6c34311339 100644 --- a/keyboards/planck/keymaps/callum/keymap.c +++ b/keyboards/planck/keymaps/callum/keymap.c @@ -20,7 +20,8 @@ enum planck_keycodes { BASE = SAFE_RANGE, MOVE, SYMB, - FUNC + FUNC, + LOCK }; // Fillers to make layering more clear @@ -37,14 +38,14 @@ const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = { * |------+------+------+------+------+------|------+------+------+------+------+------| * | Shift| Z | X | C | V | B | K | M | , | . | / |Shift | * |------+------+------+------+------+------+------+------+------+------+------+------| - * | Func | GUI | Alt | Ctrl | Symb |Enter |Space | Move | GUI | Alt | Ctrl |Caps | + * | Func | Ctrl | Alt | GUI | Symb |Enter |Space | Move | GUI | Alt | Ctrl |Caps | * `-----------------------------------------------------------------------------------' */ [_BASE] = { {KC_TAB, KC_Q, KC_W, KC_F, KC_P, KC_G, KC_J, KC_L, KC_U, KC_Y, KC_SCLN, KC_MINS}, {KC_BSPC, KC_A, KC_R, KC_S, KC_T, KC_D, KC_H, KC_N, KC_E, KC_I, KC_O, KC_QUOT}, {KC_LSFT, KC_Z, KC_X, KC_C, KC_V, KC_B, KC_K, KC_M, KC_COMM, KC_DOT, KC_SLSH, KC_RSFT}, - {FUNC, KC_LGUI, KC_LALT, KC_LCTL, SYMB, KC_ENT, KC_SPC, MOVE, KC_RGUI, KC_RALT, KC_RCTL, KC_CAPS} + {FUNC, KC_LCTL, KC_LALT, KC_LGUI, SYMB, KC_ENT, KC_SPC, MOVE, KC_RGUI, KC_RALT, KC_RCTL, KC_CAPS} }, /* MOVE @@ -87,7 +88,7 @@ const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = { * ,-----------------------------------------------------------------------------------. * | F12 | F1 | F2 | F3 | F4 | F5 | F6 | F7 | F8 | F9 | F10 | F11 | * |-----------------------------------------------------------------------------------. - * | | Play | Prev | Next | BL+ | | | | | | | | + * | | Play | Prev | Next | BL+ | | | Lock | | | | | * |------+------+------+------+------+------|------+------+------+------+------+------| * | | Mute | Vol- | Vol+ | BL- | | | | | | | | * |------+------+------+------+------+------+------+------+------+------+------+------| @@ -96,7 +97,7 @@ const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = { */ [_FUNC] = { {KC_F12, KC_F1, KC_F2, KC_F3, KC_F4, KC_F5, KC_F6, KC_F7, KC_F8, KC_F9, KC_F10, KC_F11 }, - {_______, KC_MPLY, KC_MPRV, KC_MNXT, KC_PAUS, _______, _______, _______, _______, _______, _______, _______}, + {_______, KC_MPLY, KC_MPRV, KC_MNXT, KC_PAUS, _______, _______, LOCK, _______, _______, _______, _______}, {_______, KC_MUTE, KC_VOLD, KC_VOLU, KC_SLCK, _______, _______, _______, _______, _______, _______, _______}, {_______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, RESET } } @@ -133,6 +134,18 @@ bool process_record_user(uint16_t keycode, keyrecord_t *record) { } return false; break; + case LOCK: + if (record->event.pressed) { + register_code(KC_RSFT); + register_code(KC_RCTL); + register_code(KC_POWER); + } else { + unregister_code(KC_POWER); + unregister_code(KC_RCTL); + unregister_code(KC_RSFT); + } + return false; + break; } return true; } diff --git a/keyboards/planck/keymaps/callum/readme.md b/keyboards/planck/keymaps/callum/readme.md index 030def7f77..b70de3f1e2 100644 --- a/keyboards/planck/keymaps/callum/readme.md +++ b/keyboards/planck/keymaps/callum/readme.md @@ -1,25 +1,20 @@ # callum’s planck layout -This is a layout for the grid planck, built with a few ideals in mind. These ideals are just my opinion mind! The great thing about *qmk* is that we can all afford to have different opinions about what makes a good layout: +This is a layout for the grid planck, built with a few ideals in mind: -- Minimal response times should be maintained. i.e. keys that react differently depending on whether they are tapped or held, keys that react differently if they are double tapped, etc. should be avoided --- since they inevitably send their keycode later than a normal key, interrupting the immediate feedback from the screen. Therefore we restrict ourselves to chording. +- Minimal response times should be maintained. i.e. keys that react differently depending on whether they are tapped or held, keys that react differently if they are double tapped, etc. should be avoided — they inevitably send their keycode later than a normal key, interrupting the immediate feedback from the screen. Therefore we restrict ourselves to chording. - The hands should never need to leave the home position. The usual culprit for this is the arrow cluster, so the arrow cluster should be as close to home as possible. -- There should be two of every modifier (one on each side), since otherwise certain long key combinations become hard to make. -- Backspace should be in the “capslock position” as God intended. -- The keyboard should be usable without any firmware changes on any operating system. In my case that means it should work on *Windows* and *Linux* without any software modifications, while I can change the behaviour slightly on *macOS* in software since that’s my home OS. The images reflect the intended use on *macOS* **after** minor software tweaks; which will be noted. +- There should be two of every modifier (one on each side), otherwise certain long key combinations become hard to make. +- Backspace should be in the “capslock position” in the colemak tradition. We have four layers. A `BASE` layer, in colemak; a `MOVE` layer, with an arrow cluster etc, a `SYMB` layer, with numbers and symbols; and a `FUNC` layer, with function keys and media keys. ## The `BASE` layer - + This is the default layer; in [colemak](https://colemak.com). ` |