diff options
Diffstat (limited to 'keyboards')
| -rw-r--r-- | keyboards/lets-split/Makefile | 73 | ||||
| -rw-r--r-- | keyboards/lets-split/config.h | 87 | ||||
| -rw-r--r-- | keyboards/lets-split/keymaps/default/keymap.c | 42 | ||||
| -rw-r--r-- | keyboards/lets-split/lets-split.c | 48 | ||||
| -rw-r--r-- | keyboards/lets-split/lets-split.h | 4 | ||||
| -rw-r--r-- | keyboards/lets-split/readme.md | 0 |
6 files changed, 254 insertions, 0 deletions
diff --git a/keyboards/lets-split/Makefile b/keyboards/lets-split/Makefile new file mode 100644 index 0000000000..247f978f01 --- /dev/null +++ b/keyboards/lets-split/Makefile @@ -0,0 +1,73 @@ + + +# MCU name +#MCU = at90usb1287 +MCU = atmega32u4 + +# Processor frequency. +# This will define a symbol, F_CPU, in all source code files equal to the +# processor frequency in Hz. You can then use this symbol in your source code to +# calculate timings. Do NOT tack on a 'UL' at the end, this will be done +# automatically to create a 32-bit value in your source code. +# +# This will be an integer division of F_USB below, as it is sourced by +# F_USB after it has run through any CPU prescalers. Note that this value +# does not *change* the processor frequency - it should merely be updated to +# reflect the processor speed set externally so that the code can use accurate +# software delays. +F_CPU = 16000000 + +# +# LUFA specific +# +# Target architecture (see library "Board Types" documentation). +ARCH = AVR8 + +# Input clock frequency. +# This will define a symbol, F_USB, in all source code files equal to the +# input clock frequency (before any prescaling is performed) in Hz. This value may +# differ from F_CPU if prescaling is used on the latter, and is required as the +# raw input clock is fed directly to the PLL sections of the AVR for high speed +# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' +# at the end, this will be done automatically to create a 32-bit value in your +# source code. +# +# If no clock division is performed on the input clock inside the AVR (via the +# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. +F_USB = $(F_CPU) + +# Interrupt driven control endpoint task(+60) +OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT + + +# Boot Section Size in *bytes* +# Teensy halfKay 512 +# Teensy++ halfKay 1024 +# Atmel DFU loader 4096 +# LUFA bootloader 4096 +# USBaspLoader 2048 +OPT_DEFS += -DBOOTLOADER_SIZE=4096 + +# Build Options +# change to "no" to disable the options, or define them in the Makefile in +# the appropriate keymap folder that will get included automatically +# +BOOTMAGIC_ENABLE ?= no # Virtual DIP switch configuration(+1000) +MOUSEKEY_ENABLE ?= yes # Mouse keys(+4700) +EXTRAKEY_ENABLE ?= yes # Audio control and System control(+450) +CONSOLE_ENABLE ?= no # Console for debug(+400) +COMMAND_ENABLE ?= yes # Commands for debug and configuration +NKRO_ENABLE ?= no # Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work +BACKLIGHT_ENABLE ?= no # Enable keyboard backlight functionality +MIDI_ENABLE ?= no # MIDI controls +AUDIO_ENABLE ?= yes # Audio output on port C6 +UNICODE_ENABLE ?= no # Unicode +BLUETOOTH_ENABLE ?= no # Enable Bluetooth with the Adafruit EZ-Key HID +RGBLIGHT_ENABLE ?= no # Enable WS2812 RGB underlight. Do not enable this with audio at the same time. + +# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE +SLEEP_LED_ENABLE ?= no # Breathing sleep LED during USB suspend + +ifndef QUANTUM_DIR + include ../../Makefile +endif
\ No newline at end of file diff --git a/keyboards/lets-split/config.h b/keyboards/lets-split/config.h new file mode 100644 index 0000000000..5b464147d3 --- /dev/null +++ b/keyboards/lets-split/config.h @@ -0,0 +1,87 @@ +/* +Copyright 2012 Jun Wako <wakojun@gmail.com> + +This program is free software: you can redistribute it and/or modify +it under the terms of the GNU General Public License as published by +the Free Software Foundation, either version 2 of the License, or +(at your option) any later version. + +This program is distributed in the hope that it will be useful, +but WITHOUT ANY WARRANTY; without even the implied warranty of +MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +GNU General Public License for more details. + +You should have received a copy of the GNU General Public License +along with this program. If not, see <http://www.gnu.org/licenses/>. +*/ + +#ifndef CONFIG_H +#define CONFIG_H + +#include "config_common.h" + +/* USB Device descriptor parameter */ +#define VENDOR_ID 0xFEED +#define PRODUCT_ID 0x3060 +#define DEVICE_VER 0x0001 +#define MANUFACTURER Wootpatoot +#define PRODUCT Lets Split +#define DESCRIPTION A split keyboard for the cheap makers + +/* key matrix size */ +#define MATRIX_ROWS 4 +#define MATRIX_COLS 6 + +#define MATRIX_ROW_PINS { B5, B4, E6, D7, } +#define MATRIX_COL_PINS { F4, F5, F6, F7, B1, B3 } + +/* COL2ROW or ROW2COL */ +#define DIODE_DIRECTION COL2ROW + +/* define if matrix has ghost */ +//#define MATRIX_HAS_GHOST + +/* number of backlight levels */ +#define BACKLIGHT_LEVELS 3 + +/* Set 0 if debouncing isn't needed */ +#define DEBOUNCING_DELAY 5 + +/* Mechanical locking support. Use KC_LCAP, KC_LNUM or KC_LSCR instead in keymap */ +#define LOCKING_SUPPORT_ENABLE +/* Locking resynchronize hack */ +#define LOCKING_RESYNC_ENABLE + +/* key combination for command */ +#define IS_COMMAND() ( \ + keyboard_report->mods == (MOD_BIT(KC_LSHIFT) | MOD_BIT(KC_RSHIFT)) \ +) + +/* ws2812 RGB LED */ +#define ws2812_PORTREG PORTD +#define ws2812_DDRREG DDRD +#define ws2812_pin PD1 +#define RGBLED_NUM 28 // Number of LEDs +#define RGBLIGHT_HUE_STEP 10 +#define RGBLIGHT_SAT_STEP 17 +#define RGBLIGHT_VAL_STEP 17 + +/* + * Feature disable options + * These options are also useful to firmware size reduction. + */ + +/* disable debug print */ +// #define NO_DEBUG + +/* disable print */ +// #define NO_PRINT + +/* disable action features */ +//#define NO_ACTION_LAYER +//#define NO_ACTION_TAPPING +//#define NO_ACTION_ONESHOT +//#define NO_ACTION_MACRO +//#define NO_ACTION_FUNCTION + +#endif
\ No newline at end of file diff --git a/keyboards/lets-split/keymaps/default/keymap.c b/keyboards/lets-split/keymaps/default/keymap.c new file mode 100644 index 0000000000..00602394fe --- /dev/null +++ b/keyboards/lets-split/keymaps/default/keymap.c @@ -0,0 +1,42 @@ +#include "lets-split.h" +#include "action_layer.h" + +#define BASE 0 + +enum preonic_keycodes { + KC_IDK = SAFE_RANGE, + PM_RESET +}; + +// Fillers to make layering more clear +#define _______ KC_TRNS +#define XXXXXXX KC_NO + +const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = { + +[BASE] = { + {KC_TAB, KC_Q, KC_W, KC_E, KC_R, KC_T }, + {KC_ESC, KC_A, KC_S, KC_D, KC_F, KC_G }, + {KC_LSFT, KC_Z, KC_X, KC_C, KC_V, KC_B }, + {KC_IDK, KC_LCTL, KC_LALT, KC_LGUI, KC_SPC, PM_RESET } +} + +}; + +bool process_record_user(uint16_t keycode, keyrecord_t *record) { + switch (keycode) { + case KC_IDK: + if (record->event.pressed) { + SEND_STRING("IDK. "); + } + return false; + break; + case PM_RESET: + if (record->event.pressed) { + promicro_bootloader_jmp(true); + } + return false; + break; + } + return true; +};
\ No newline at end of file diff --git a/keyboards/lets-split/lets-split.c b/keyboards/lets-split/lets-split.c new file mode 100644 index 0000000000..ee98723037 --- /dev/null +++ b/keyboards/lets-split/lets-split.c @@ -0,0 +1,48 @@ +#include "lets-split.h" + +#ifdef AUDIO_ENABLE + float tone_startup[][2] = SONG(STARTUP_SOUND); + float tone_goodbye[][2] = SONG(GOODBYE_SOUND); +#endif + +void matrix_init_kb(void) { + + #ifdef AUDIO_ENABLE + _delay_ms(20); // gets rid of tick + PLAY_NOTE_ARRAY(tone_startup, false, 0); + #endif + + // green led on + DDRD |= (1<<5); + PORTD &= ~(1<<5); + + // orange led on + DDRB |= (1<<0); + PORTB &= ~(1<<0); + + matrix_init_user(); +}; + +void promicro_bootloader_jmp(bool program) { + + #ifdef AUDIO_ENABLE + PLAY_NOTE_ARRAY(tone_goodbye, false, 0); + _delay_ms(150); + stop_all_notes(); + #endif + + uint16_t *const bootKeyPtr = (uint16_t *)0x0800; + + // Value used by Caterina bootloader use to determine whether to run the + // sketch or the bootloader programmer. + uint16_t bootKey = program ? 0x7777 : 0; + + *bootKeyPtr = bootKey; + + // setup watchdog timeout + wdt_enable(WDTO_60MS); + + while(1) {} // wait for watchdog timer to trigger +} + + diff --git a/keyboards/lets-split/lets-split.h b/keyboards/lets-split/lets-split.h new file mode 100644 index 0000000000..c82b95a376 --- /dev/null +++ b/keyboards/lets-split/lets-split.h @@ -0,0 +1,4 @@ +#include "quantum.h" +#include <avr/wdt.h> + +void promicro_bootloader_jmp(bool program);
\ No newline at end of file diff --git a/keyboards/lets-split/readme.md b/keyboards/lets-split/readme.md new file mode 100644 index 0000000000..e69de29bb2 --- /dev/null +++ b/keyboards/lets-split/readme.md |