diff options
Diffstat (limited to 'keyboards')
55 files changed, 136 insertions, 516 deletions
diff --git a/keyboards/40percentclub/ut47/config.h b/keyboards/40percentclub/ut47/config.h index 197d6cd181..9622f58bb3 100644 --- a/keyboards/40percentclub/ut47/config.h +++ b/keyboards/40percentclub/ut47/config.h @@ -54,25 +54,3 @@ along with this program. If not, see <http://www.gnu.org/licenses/>. /* Enable GNAP matrix serial output */ #define GNAP_ENABLE - -/* USART configuration */ -#ifdef __AVR_ATmega32U4__ -# define SERIAL_UART_BAUD 9600 -# define SERIAL_UART_DATA UDR1 -# define SERIAL_UART_UBRR (F_CPU / (16UL * SERIAL_UART_BAUD) - 1) -# define SERIAL_UART_RXD_VECT USART1_RX_vect -# define SERIAL_UART_TXD_READY (UCSR1A & _BV(UDRE1)) -# define SERIAL_UART_INIT() do { \ - /* baud rate */ \ - UBRR1L = SERIAL_UART_UBRR; \ - /* baud rate */ \ - UBRR1H = SERIAL_UART_UBRR >> 8; \ - /* enable TX */ \ - UCSR1B = _BV(TXEN1); \ - /* 8-bit data */ \ - UCSR1C = _BV(UCSZ11) | _BV(UCSZ10); \ - sei(); \ - } while(0) -# else -# error "USART configuration is needed." -#endif diff --git a/keyboards/centromere/centromere.c b/keyboards/centromere/centromere.c index 8800e2ce6a..269c60fd75 100644 --- a/keyboards/centromere/centromere.c +++ b/keyboards/centromere/centromere.c @@ -1,9 +1,5 @@ #include "centromere.h" -void uart_init(void) { - SERIAL_UART_INIT(); -} - void led_init(void) { #if MCU == atmega32u2 setPinOutput(C4); // Set red LED pin as output @@ -32,7 +28,6 @@ void matrix_init_kb(void) { // put your keyboard start-up code here // runs once when the firmware starts up matrix_init_user(); - uart_init(); led_init(); } diff --git a/keyboards/centromere/config.h b/keyboards/centromere/config.h index 0a908f60f9..e502e2534b 100644 --- a/keyboards/centromere/config.h +++ b/keyboards/centromere/config.h @@ -59,17 +59,9 @@ along with this program. If not, see <http://www.gnu.org/licenses/>. //UART settings for communication with the RF microcontroller #define SERIAL_UART_BAUD 500000 -#define SERIAL_UART_DATA UDR1 -#define SERIAL_UART_UBRR (F_CPU / (16UL * SERIAL_UART_BAUD) - 1) -#define SERIAL_UART_TXD_READY (UCSR1A & _BV(UDRE1)) #define SERIAL_UART_RXD_PRESENT (UCSR1A & _BV(RXC1)) -#define SERIAL_UART_INIT() do { \ - /* baud rate */ \ - UBRR1L = SERIAL_UART_UBRR; \ - /* baud rate */ \ - UBRR1H = SERIAL_UART_UBRR >> 8; \ - /* enable TX and RX */ \ - UCSR1B = _BV(TXEN1) | _BV(RXEN1); \ - /* 8-bit data */ \ - UCSR1C = _BV(UCSZ11) | _BV(UCSZ10); \ - } while(0) +#define SERIAL_UART_INIT_CUSTOM \ + /* enable TX and RX */ \ + UCSR1B = _BV(TXEN1) | _BV(RXEN1); \ + /* 8-bit data */ \ + UCSR1C = _BV(UCSZ11) | _BV(UCSZ10); diff --git a/keyboards/centromere/matrix.c b/keyboards/centromere/matrix.c index c5fc8db6ce..5ca083b435 100644 --- a/keyboards/centromere/matrix.c +++ b/keyboards/centromere/matrix.c @@ -26,6 +26,7 @@ along with this program. If not, see <http://www.gnu.org/licenses/>. #include "util.h" #include "matrix.h" #include "timer.h" +#include "protocol/serial.h" #if (MATRIX_COLS <= 8) # define print_matrix_header() print("\nr/c 01234567\n") @@ -79,12 +80,11 @@ uint8_t matrix_cols(void) { void matrix_init(void) { matrix_init_quantum(); + serial_init(); } uint8_t matrix_scan(void) { - SERIAL_UART_INIT(); - uint32_t timeout = 0; //the s character requests the RF remote slave to send the matrix information diff --git a/keyboards/centromere/rules.mk b/keyboards/centromere/rules.mk index f08f6e6ebd..2469d244a6 100644 --- a/keyboards/centromere/rules.mk +++ b/keyboards/centromere/rules.mk @@ -31,14 +31,7 @@ MIDI_ENABLE = no # MIDI controls UNICODE_ENABLE = yes # Unicode BLUETOOTH_ENABLE = no # Enable Bluetooth with the Adafruit EZ-Key HID -USB = /dev/ttyACM0 - -# upload: build -# $(CENTROMERE_UPLOAD_COMMAND) - -OPT_DEFS += -DCENTROMERE_PROMICRO - # # project specific files -SRC = matrix.c +SRC += matrix.c serial_uart.c LAYOUTS = split_3x5_3 split_3x6_3 diff --git a/keyboards/chimera_ergo/chimera_ergo.c b/keyboards/chimera_ergo/chimera_ergo.c index 29470f9080..47653c2e4b 100644 --- a/keyboards/chimera_ergo/chimera_ergo.c +++ b/keyboards/chimera_ergo/chimera_ergo.c @@ -1,9 +1,5 @@ #include "chimera_ergo.h" -void uart_init(void) { - SERIAL_UART_INIT(); -} - void led_init(void) { DDRD |= (1<<1); PORTD |= (1<<1); @@ -16,16 +12,5 @@ void matrix_init_kb(void) { // put your keyboard start-up code here // runs once when the firmware starts up matrix_init_user(); - uart_init(); led_init(); } - -void matrix_scan_kb(void) { - // put your looping keyboard code here - // runs every cycle (a lot) - matrix_scan_user(); -} - -void led_set_kb(uint8_t usb_led) { - -} diff --git a/keyboards/chimera_ergo/config.h b/keyboards/chimera_ergo/config.h index 262f287a50..4021cdcd50 100644 --- a/keyboards/chimera_ergo/config.h +++ b/keyboards/chimera_ergo/config.h @@ -60,19 +60,11 @@ along with this program. If not, see <http://www.gnu.org/licenses/>. //UART settings for communication with the RF microcontroller #define SERIAL_UART_BAUD 1000000 -#define SERIAL_UART_DATA UDR1 -#define SERIAL_UART_UBRR (F_CPU / (16UL * SERIAL_UART_BAUD) - 1) -#define SERIAL_UART_TXD_READY (UCSR1A & _BV(UDRE1)) #define SERIAL_UART_RXD_PRESENT (UCSR1A & _BV(RXC1)) -#define SERIAL_UART_INIT() do { \ - /* baud rate */ \ - UBRR1L = SERIAL_UART_UBRR; \ - /* baud rate */ \ - UBRR1H = SERIAL_UART_UBRR >> 8; \ - /* enable TX and RX */ \ - UCSR1B = _BV(TXEN1) | _BV(RXEN1); \ - /* 8-bit data */ \ - UCSR1C = _BV(UCSZ11) | _BV(UCSZ10); \ - } while(0) +#define SERIAL_UART_INIT_CUSTOM \ + /* enable TX and RX */ \ + UCSR1B = _BV(TXEN1) | _BV(RXEN1); \ + /* 8-bit data */ \ + UCSR1C = _BV(UCSZ11) | _BV(UCSZ10); #endif diff --git a/keyboards/chimera_ergo/matrix.c b/keyboards/chimera_ergo/matrix.c index d512a51d97..112b9a40d1 100644 --- a/keyboards/chimera_ergo/matrix.c +++ b/keyboards/chimera_ergo/matrix.c @@ -26,6 +26,7 @@ along with this program. If not, see <http://www.gnu.org/licenses/>. #include "util.h" #include "matrix.h" #include "timer.h" +#include "protocol/serial.h" #if (MATRIX_COLS <= 8) # define print_matrix_header() print("\nr/c 01234567\n") @@ -88,12 +89,11 @@ uint8_t matrix_cols(void) { void matrix_init(void) { matrix_init_quantum(); + serial_init(); } uint8_t matrix_scan(void) { - SERIAL_UART_INIT(); - uint32_t timeout = 0; //the s character requests the RF slave to send the matrix diff --git a/keyboards/chimera_ergo/rules.mk b/keyboards/chimera_ergo/rules.mk index f37d14107b..01d5c3c70c 100644 --- a/keyboards/chimera_ergo/rules.mk +++ b/keyboards/chimera_ergo/rules.mk @@ -28,12 +28,5 @@ NKRO_ENABLE = yes # USB Nkey Rollover - not yet supported in LUFA UNICODE_ENABLE = YES # Unicode # BLUETOOTH_ENABLE = yes # Enable Bluetooth with the Adafruit EZ-Key HID - -OPT_DEFS += -DCHIMERA_ERGO_PROMICRO -CHIMERA_ERGO_UPLOAD_COMMAND = while [ ! -r $(USB) ]; do sleep 1; done; \ - avrdude -p $(MCU) -c avr109 -U flash:w:$(TARGET).hex -P $(USB) - # # project specific files -SRC = matrix.c - -USB = /dev/ttyACM0 +SRC += matrix.c serial_uart.c diff --git a/keyboards/chimera_ls/chimera_ls.c b/keyboards/chimera_ls/chimera_ls.c index 588b02b2d1..f88e9a4f12 100644 --- a/keyboards/chimera_ls/chimera_ls.c +++ b/keyboards/chimera_ls/chimera_ls.c @@ -1,9 +1,5 @@ #include "chimera_ls.h" -void uart_init(void) { - SERIAL_UART_INIT(); -} - void led_init(void) { DDRD |= (1<<1); PORTD |= (1<<1); @@ -16,16 +12,5 @@ void matrix_init_kb(void) { // put your keyboard start-up code here // runs once when the firmware starts up matrix_init_user(); - uart_init(); led_init(); } - -void matrix_scan_kb(void) { - // put your looping keyboard code here - // runs every cycle (a lot) - matrix_scan_user(); -} - -void led_set_kb(uint8_t usb_led) { - -} diff --git a/keyboards/chimera_ls/config.h b/keyboards/chimera_ls/config.h index 87e9196095..d9c14a3fce 100644 --- a/keyboards/chimera_ls/config.h +++ b/keyboards/chimera_ls/config.h @@ -60,19 +60,11 @@ along with this program. If not, see <http://www.gnu.org/licenses/>. //UART settings for communication with the RF microcontroller #define SERIAL_UART_BAUD 1000000 -#define SERIAL_UART_DATA UDR1 -#define SERIAL_UART_UBRR (F_CPU / (16UL * SERIAL_UART_BAUD) - 1) -#define SERIAL_UART_TXD_READY (UCSR1A & _BV(UDRE1)) #define SERIAL_UART_RXD_PRESENT (UCSR1A & _BV(RXC1)) -#define SERIAL_UART_INIT() do { \ - /* baud rate */ \ - UBRR1L = SERIAL_UART_UBRR; \ - /* baud rate */ \ - UBRR1H = SERIAL_UART_UBRR >> 8; \ - /* enable TX and RX */ \ - UCSR1B = _BV(TXEN1) | _BV(RXEN1); \ - /* 8-bit data */ \ - UCSR1C = _BV(UCSZ11) | _BV(UCSZ10); \ - } while(0) +#define SERIAL_UART_INIT_CUSTOM \ + /* enable TX and RX */ \ + UCSR1B = _BV(TXEN1) | _BV(RXEN1); \ + /* 8-bit data */ \ + UCSR1C = _BV(UCSZ11) | _BV(UCSZ10); #endif diff --git a/keyboards/chimera_ls/matrix.c b/keyboards/chimera_ls/matrix.c index 72fe441370..7208d971e1 100644 --- a/keyboards/chimera_ls/matrix.c +++ b/keyboards/chimera_ls/matrix.c @@ -26,6 +26,7 @@ along with this program. If not, see <http://www.gnu.org/licenses/>. #include "util.h" #include "matrix.h" #include "timer.h" +#include "protocol/serial.h" #if (MATRIX_COLS <= 8) # define print_matrix_header() print("\nr/c 01234567\n") @@ -92,12 +93,11 @@ uint8_t matrix_cols(void) { void matrix_init(void) { matrix_init_quantum(); + serial_init(); } uint8_t matrix_scan(void) { - SERIAL_UART_INIT(); - uint32_t timeout = 0; //the s character requests the RF slave to send the matrix diff --git a/keyboards/chimera_ls/rules.mk b/keyboards/chimera_ls/rules.mk index 162e06aaf7..536e6053a1 100644 --- a/keyboards/chimera_ls/rules.mk +++ b/keyboards/chimera_ls/rules.mk @@ -28,14 +28,8 @@ NKRO_ENABLE = yes # USB Nkey Rollover - not yet supported in LUFA UNICODE_ENABLE = YES # Unicode # BLUETOOTH_ENABLE = yes # Enable Bluetooth with the Adafruit EZ-Key HID -USB = /dev/ttyACM0 - -OPT_DEFS += -DCHIMERA_LS_PROMICRO -CHIMERA_LS_UPLOAD_COMMAND = while [ ! -r $(USB) ]; do sleep 1; done; \ - avrdude -p $(MCU) -c avr109 -U flash:w:$(TARGET).hex -P $(USB) - # project specific files -SRC = matrix.c +SRC += matrix.c serial_uart.c LAYOUTS = ortho_4x12 diff --git a/keyboards/chimera_ortho/chimera_ortho.c b/keyboards/chimera_ortho/chimera_ortho.c index 2a602cf2f7..2cdc3d9331 100644 --- a/keyboards/chimera_ortho/chimera_ortho.c +++ b/keyboards/chimera_ortho/chimera_ortho.c @@ -1,9 +1,5 @@ #include "chimera_ortho.h" -void uart_init(void) { - SERIAL_UART_INIT(); -} - void led_init(void) { DDRD |= (1<<1); PORTD |= (1<<1); @@ -16,16 +12,5 @@ void matrix_init_kb(void) { // put your keyboard start-up code here // runs once when the firmware starts up matrix_init_user(); - uart_init(); led_init(); } - -void matrix_scan_kb(void) { - // put your looping keyboard code here - // runs every cycle (a lot) - matrix_scan_user(); -} - -void led_set_kb(uint8_t usb_led) { - -} diff --git a/keyboards/chimera_ortho/config.h b/keyboards/chimera_ortho/config.h index 4ce70e68ba..b103589879 100644 --- a/keyboards/chimera_ortho/config.h +++ b/keyboards/chimera_ortho/config.h @@ -60,19 +60,11 @@ along with this program. If not, see <http://www.gnu.org/licenses/>. //UART settings for communication with the RF microcontroller #define SERIAL_UART_BAUD 1000000 -#define SERIAL_UART_DATA UDR1 -#define SERIAL_UART_UBRR (F_CPU / (16UL * SERIAL_UART_BAUD) - 1) -#define SERIAL_UART_TXD_READY (UCSR1A & _BV(UDRE1)) #define SERIAL_UART_RXD_PRESENT (UCSR1A & _BV(RXC1)) -#define SERIAL_UART_INIT() do { \ - /* baud rate */ \ - UBRR1L = SERIAL_UART_UBRR; \ - /* baud rate */ \ - UBRR1H = SERIAL_UART_UBRR >> 8; \ - /* enable TX and RX */ \ - UCSR1B = _BV(TXEN1) | _BV(RXEN1); \ - /* 8-bit data */ \ - UCSR1C = _BV(UCSZ11) | _BV(UCSZ10); \ - } while(0) +#define SERIAL_UART_INIT_CUSTOM \ + /* enable TX and RX */ \ + UCSR1B = _BV(TXEN1) | _BV(RXEN1); \ + /* 8-bit data */ \ + UCSR1C = _BV(UCSZ11) | _BV(UCSZ10); #endif diff --git a/keyboards/chimera_ortho/matrix.c b/keyboards/chimera_ortho/matrix.c index dc38ba74f8..eb2f18473e 100644 --- a/keyboards/chimera_ortho/matrix.c +++ b/keyboards/chimera_ortho/matrix.c @@ -26,6 +26,7 @@ along with this program. If not, see <http://www.gnu.org/licenses/>. #include "util.h" #include "matrix.h" #include "timer.h" +#include "protocol/serial.h" #if (MATRIX_COLS <= 8) # define print_matrix_header() print("\nr/c 01234567\n") @@ -78,12 +79,11 @@ uint8_t matrix_cols(void) { void matrix_init(void) { matrix_init_quantum(); + serial_init(); } uint8_t matrix_scan(void) { - SERIAL_UART_INIT(); - uint32_t timeout = 0; //the s character requests the RF slave to send the matrix diff --git a/keyboards/chimera_ortho/rules.mk b/keyboards/chimera_ortho/rules.mk index bf341ab5dd..e3bbaa39d4 100644 --- a/keyboards/chimera_ortho/rules.mk +++ b/keyboards/chimera_ortho/rules.mk @@ -28,11 +28,5 @@ NKRO_ENABLE = yes # USB Nkey Rollover - not yet supported in LUFA UNICODE_ENABLE = YES # Unicode # BLUETOOTH_ENABLE = yes # Enable Bluetooth with the Adafruit EZ-Key HID -USB = /dev/ttyACM0 - -OPT_DEFS += -DCHIMERA_ORTHO_PROMICRO -CHIMERA_ORTHO_UPLOAD_COMMAND = while [ ! -r $(USB) ]; do sleep 1; done; \ - avrdude -p $(MCU) -c avr109 -U flash:w:$(TARGET).hex -P $(USB) - # project specific files -SRC = matrix.c +SRC += matrix.c serial_uart.c diff --git a/keyboards/chimera_ortho_plus/chimera_ortho_plus.c b/keyboards/chimera_ortho_plus/chimera_ortho_plus.c index 1972f2a9c3..6d87ed7053 100644 --- a/keyboards/chimera_ortho_plus/chimera_ortho_plus.c +++ b/keyboards/chimera_ortho_plus/chimera_ortho_plus.c @@ -1,9 +1,5 @@ #include "chimera_ortho_plus.h" -void uart_init(void) { - SERIAL_UART_INIT(); -} - void led_init(void) { setPinOutput(D1); setPinOutput(F4); @@ -18,6 +14,5 @@ void matrix_init_kb(void) { // put your keyboard start-up code here // runs once when the firmware starts up matrix_init_user(); - uart_init(); led_init(); } diff --git a/keyboards/chimera_ortho_plus/config.h b/keyboards/chimera_ortho_plus/config.h index e060e196aa..4b12796e95 100644 --- a/keyboards/chimera_ortho_plus/config.h +++ b/keyboards/chimera_ortho_plus/config.h @@ -59,17 +59,9 @@ along with this program. If not, see <http://www.gnu.org/licenses/>. //UART settings for communication with the RF microcontroller #define SERIAL_UART_BAUD 1000000 -#define SERIAL_UART_DATA UDR1 -#define SERIAL_UART_UBRR (F_CPU / (16UL * SERIAL_UART_BAUD) - 1) -#define SERIAL_UART_TXD_READY (UCSR1A & _BV(UDRE1)) #define SERIAL_UART_RXD_PRESENT (UCSR1A & _BV(RXC1)) -#define SERIAL_UART_INIT() do { \ - /* baud rate */ \ - UBRR1L = SERIAL_UART_UBRR; \ - /* baud rate */ \ - UBRR1H = SERIAL_UART_UBRR >> 8; \ - /* enable TX and RX */ \ - UCSR1B = _BV(TXEN1) | _BV(RXEN1); \ - /* 8-bit data */ \ - UCSR1C = _BV(UCSZ11) | _BV(UCSZ10); \ - } while(0) +#define SERIAL_UART_INIT_CUSTOM \ + /* enable TX and RX */ \ + UCSR1B = _BV(TXEN1) | _BV(RXEN1); \ + /* 8-bit data */ \ + UCSR1C = _BV(UCSZ11) | _BV(UCSZ10); diff --git a/keyboards/chimera_ortho_plus/matrix.c b/keyboards/chimera_ortho_plus/matrix.c index ed6eac2b09..2bdc97991c 100644 --- a/keyboards/chimera_ortho_plus/matrix.c +++ b/keyboards/chimera_ortho_plus/matrix.c @@ -26,6 +26,7 @@ along with this program. If not, see <http://www.gnu.org/licenses/>. #include "util.h" #include "matrix.h" #include "timer.h" +#include "protocol/serial.h" #if (MATRIX_COLS <= 8) # define print_matrix_header() print("\nr/c 01234567\n") @@ -78,12 +79,11 @@ uint8_t matrix_cols(void) { void matrix_init(void) { matrix_init_quantum(); + serial_init(); } uint8_t matrix_scan(void) { - SERIAL_UART_INIT(); - uint32_t timeout = 0; //the s character requests the RF slave to send the matrix diff --git a/keyboards/chimera_ortho_plus/rules.mk b/keyboards/chimera_ortho_plus/rules.mk index 2dd6c3e1f0..fec1bef730 100644 --- a/keyboards/chimera_ortho_plus/rules.mk +++ b/keyboards/chimera_ortho_plus/rules.mk @@ -33,4 +33,4 @@ UNICODE_ENABLE = yes CUSTOM_MATRIX = yes # project specific files -SRC = matrix.c +SRC += matrix.c serial_uart.c diff --git a/keyboards/comet46/comet46.c b/keyboards/comet46/comet46.c index 0710b8e330..7c7edba93e 100644 --- a/keyboards/comet46/comet46.c +++ b/keyboards/comet46/comet46.c @@ -1,22 +1 @@ #include "comet46.h" - -void uart_init(void) { - SERIAL_UART_INIT(); -} - -void matrix_init_kb(void) { - // put your keyboard start-up code here - // runs once when the firmware starts up - matrix_init_user(); - uart_init(); -} - -void matrix_scan_kb(void) { - // put your looping keyboard code here - // runs every cycle (a lot) - matrix_scan_user(); -} - -void led_set_kb(uint8_t usb_led) { - -} diff --git a/keyboards/comet46/config.h b/keyboards/comet46/config.h index d50224eb60..5ae026f923 100644 --- a/keyboards/comet46/config.h +++ b/keyboards/comet46/config.h @@ -66,19 +66,11 @@ along with this program. If not, see <http://www.gnu.org/licenses/>. //UART settings for communication with the RF microcontroller #define SERIAL_UART_BAUD 1000000 -#define SERIAL_UART_DATA UDR1 -#define SERIAL_UART_UBRR (F_CPU / (16UL * SERIAL_UART_BAUD) - 1) -#define SERIAL_UART_TXD_READY (UCSR1A & _BV(UDRE1)) #define SERIAL_UART_RXD_PRESENT (UCSR1A & _BV(RXC1)) -#define SERIAL_UART_INIT() do { \ - /* baud rate */ \ - UBRR1L = SERIAL_UART_UBRR; \ - /* baud rate */ \ - UBRR1H = SERIAL_UART_UBRR >> 8; \ - /* enable TX and RX */ \ - UCSR1B = _BV(TXEN1) | _BV(RXEN1); \ - /* 8-bit data */ \ - UCSR1C = _BV(UCSZ11) | _BV(UCSZ10); \ - } while(0) +#define SERIAL_UART_INIT_CUSTOM \ + /* enable TX and RX */ \ + UCSR1B = _BV(TXEN1) | _BV(RXEN1); \ + /* 8-bit data */ \ + UCSR1C = _BV(UCSZ11) | _BV(UCSZ10); #endif diff --git a/keyboards/comet46/matrix.c b/keyboards/comet46/matrix.c index dc38ba74f8..eb2f18473e 100644 --- a/keyboards/comet46/matrix.c +++ b/keyboards/comet46/matrix.c @@ -26,6 +26,7 @@ along with this program. If not, see <http://www.gnu.org/licenses/>. #include "util.h" #include "matrix.h" #include "timer.h" +#include "protocol/serial.h" #if (MATRIX_COLS <= 8) # define print_matrix_header() print("\nr/c 01234567\n") @@ -78,12 +79,11 @@ uint8_t matrix_cols(void) { void matrix_init(void) { matrix_init_quantum(); + serial_init(); } |