diff options
Diffstat (limited to 'keyboards/planck')
| -rw-r--r-- | keyboards/planck/Makefile | 71 | ||||
| -rw-r--r-- | keyboards/planck/readme.md | 8 | ||||
| -rw-r--r-- | keyboards/planck/rev3/Makefile | 4 | ||||
| -rw-r--r-- | keyboards/planck/rev3/rules.mk | 5 | ||||
| -rw-r--r-- | keyboards/planck/rev4/Makefile | 4 | ||||
| -rw-r--r-- | keyboards/planck/rev4/rules.mk | 5 | ||||
| -rw-r--r-- | keyboards/planck/rules.mk | 67 |
7 files changed, 85 insertions, 79 deletions
diff --git a/keyboards/planck/Makefile b/keyboards/planck/Makefile index 23944f92ea..7d49c5ef96 100644 --- a/keyboards/planck/Makefile +++ b/keyboards/planck/Makefile @@ -1,74 +1,5 @@ - SUBPROJECT_DEFAULT = rev4 -# MCU name -#MCU = at90usb1287 -MCU = atmega32u4 - -# Processor frequency. -# This will define a symbol, F_CPU, in all source code files equal to the -# processor frequency in Hz. You can then use this symbol in your source code to -# calculate timings. Do NOT tack on a 'UL' at the end, this will be done -# automatically to create a 32-bit value in your source code. -# -# This will be an integer division of F_USB below, as it is sourced by -# F_USB after it has run through any CPU prescalers. Note that this value -# does not *change* the processor frequency - it should merely be updated to -# reflect the processor speed set externally so that the code can use accurate -# software delays. -F_CPU = 16000000 - -# -# LUFA specific -# -# Target architecture (see library "Board Types" documentation). -ARCH = AVR8 - -# Input clock frequency. -# This will define a symbol, F_USB, in all source code files equal to the -# input clock frequency (before any prescaling is performed) in Hz. This value may -# differ from F_CPU if prescaling is used on the latter, and is required as the -# raw input clock is fed directly to the PLL sections of the AVR for high speed -# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' -# at the end, this will be done automatically to create a 32-bit value in your -# source code. -# -# If no clock division is performed on the input clock inside the AVR (via the -# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. -F_USB = $(F_CPU) - -# Interrupt driven control endpoint task(+60) -OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT - - -# Boot Section Size in *bytes* -# Teensy halfKay 512 -# Teensy++ halfKay 1024 -# Atmel DFU loader 4096 -# LUFA bootloader 4096 -# USBaspLoader 2048 -OPT_DEFS += -DBOOTLOADER_SIZE=4096 - -# Build Options -# change to "no" to disable the options, or define them in the Makefile in -# the appropriate keymap folder that will get included automatically -# -BOOTMAGIC_ENABLE ?= no # Virtual DIP switch configuration(+1000) -MOUSEKEY_ENABLE ?= yes # Mouse keys(+4700) -EXTRAKEY_ENABLE ?= yes # Audio control and System control(+450) -CONSOLE_ENABLE ?= no # Console for debug(+400) -COMMAND_ENABLE ?= yes # Commands for debug and configuration -NKRO_ENABLE ?= no # Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work -BACKLIGHT_ENABLE ?= yes # Enable keyboard backlight functionality -MIDI_ENABLE ?= no # MIDI controls -AUDIO_ENABLE ?= no # Audio output on port C6 -UNICODE_ENABLE ?= no # Unicode -BLUETOOTH_ENABLE ?= no # Enable Bluetooth with the Adafruit EZ-Key HID -RGBLIGHT_ENABLE ?= no # Enable WS2812 RGB underlight. Do not enable this with audio at the same time. - -# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE -SLEEP_LED_ENABLE ?= no # Breathing sleep LED during USB suspend - -ifndef QUANTUM_DIR +ifndef MAKEFILE_INCLUDED include ../../Makefile endif
\ No newline at end of file diff --git a/keyboards/planck/readme.md b/keyboards/planck/readme.md index f89fdeb931..4b24a690e0 100644 --- a/keyboards/planck/readme.md +++ b/keyboards/planck/readme.md @@ -13,15 +13,17 @@ Download or clone the whole firmware and navigate to the keyboards/planck folder Depending on which keymap you would like to use, you will have to compile slightly differently. ### Default -To build with the default keymap, simply run `make`. +To build with the default keymap, simply run `make default`. ### Other Keymaps Several version of keymap are available in advance but you are recommended to define your favorite layout yourself. To define your own keymap create file named `<name>.c` in the keymaps folder, and see keymap document (you can find in top readme.md) and existent keymap files. -To build the firmware binary hex file with a keymap just do `make` with `KEYMAP` option like: +To build the firmware binary hex file with a keymap just do `make` with a keymap like this: + ``` -$ make KEYMAP=[default|jack|<name>] +$ make [default|jack|<name>] ``` + Keymaps follow the format **__\<name\>.c__** and are stored in the `keymaps` folder. ### Notable forks (which some of the keymap files are from) diff --git a/keyboards/planck/rev3/Makefile b/keyboards/planck/rev3/Makefile index 3ed1445e43..191c6bb664 100644 --- a/keyboards/planck/rev3/Makefile +++ b/keyboards/planck/rev3/Makefile @@ -1,5 +1,3 @@ -AUDIO_ENABLE ?= no # Audio output on port C6 - -ifndef QUANTUM_DIR +ifndef MAKEFILE_INCLUDED include ../../../Makefile endif
\ No newline at end of file diff --git a/keyboards/planck/rev3/rules.mk b/keyboards/planck/rev3/rules.mk new file mode 100644 index 0000000000..3ed1445e43 --- /dev/null +++ b/keyboards/planck/rev3/rules.mk @@ -0,0 +1,5 @@ +AUDIO_ENABLE ?= no # Audio output on port C6 + +ifndef QUANTUM_DIR + include ../../../Makefile +endif
\ No newline at end of file diff --git a/keyboards/planck/rev4/Makefile b/keyboards/planck/rev4/Makefile index ed09f85a4d..191c6bb664 100644 --- a/keyboards/planck/rev4/Makefile +++ b/keyboards/planck/rev4/Makefile @@ -1,5 +1,3 @@ -AUDIO_ENABLE ?= yes # Audio output on port C6 - -ifndef QUANTUM_DIR +ifndef MAKEFILE_INCLUDED include ../../../Makefile endif
\ No newline at end of file diff --git a/keyboards/planck/rev4/rules.mk b/keyboards/planck/rev4/rules.mk new file mode 100644 index 0000000000..ed09f85a4d --- /dev/null +++ b/keyboards/planck/rev4/rules.mk @@ -0,0 +1,5 @@ +AUDIO_ENABLE ?= yes # Audio output on port C6 + +ifndef QUANTUM_DIR + include ../../../Makefile +endif
\ No newline at end of file diff --git a/keyboards/planck/rules.mk b/keyboards/planck/rules.mk new file mode 100644 index 0000000000..25db53a315 --- /dev/null +++ b/keyboards/planck/rules.mk @@ -0,0 +1,67 @@ +# MCU name +#MCU = at90usb1287 +MCU = atmega32u4 + +# Processor frequency. +# This will define a symbol, F_CPU, in all source code files equal to the +# processor frequency in Hz. You can then use this symbol in your source code to +# calculate timings. Do NOT tack on a 'UL' at the end, this will be done +# automatically to create a 32-bit value in your source code. +# +# This will be an integer division of F_USB below, as it is sourced by +# F_USB after it has run through any CPU prescalers. Note that this value +# does not *change* the processor frequency - it should merely be updated to +# reflect the processor speed set externally so that the code can use accurate +# software delays. +F_CPU = 16000000 + +# +# LUFA specific +# +# Target architecture (see library "Board Types" documentation). +ARCH = AVR8 + +# Input clock frequency. +# This will define a symbol, F_USB, in all source code files equal to the +# input clock frequency (before any prescaling is performed) in Hz. This value may +# differ from F_CPU if prescaling is used on the latter, and is required as the +# raw input clock is fed directly to the PLL sections of the AVR for high speed +# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' +# at the end, this will be done automatically to create a 32-bit value in your +# source code. +# +# If no clock division is performed on the input clock inside the AVR (via the +# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. +F_USB = $(F_CPU) + +# Interrupt driven control endpoint task(+60) +OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT + + +# Boot Section Size in *bytes* +# Teensy halfKay 512 +# Teensy++ halfKay 1024 +# Atmel DFU loader 4096 +# LUFA bootloader 4096 +# USBaspLoader 2048 +OPT_DEFS += -DBOOTLOADER_SIZE=4096 + +# Build Options +# change to "no" to disable the options, or define them in the Makefile in +# the appropriate keymap folder that will get included automatically +# +BOOTMAGIC_ENABLE ?= no # Virtual DIP switch configuration(+1000) +MOUSEKEY_ENABLE ?= yes # Mouse keys(+4700) +EXTRAKEY_ENABLE ?= yes # Audio control and System control(+450) +CONSOLE_ENABLE ?= no # Console for debug(+400) +COMMAND_ENABLE ?= yes # Commands for debug and configuration +NKRO_ENABLE ?= no # Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work +BACKLIGHT_ENABLE ?= yes # Enable keyboard backlight functionality +MIDI_ENABLE ?= no # MIDI controls +AUDIO_ENABLE ?= no # Audio output on port C6 +UNICODE_ENABLE ?= no # Unicode +BLUETOOTH_ENABLE ?= no # Enable Bluetooth with the Adafruit EZ-Key HID +RGBLIGHT_ENABLE ?= no # Enable WS2812 RGB underlight. Do not enable this with audio at the same time. + +# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE +SLEEP_LED_ENABLE ?= no # Breathing sleep LED during USB suspend
\ No newline at end of file |