diff options
Diffstat (limited to 'keyboards/planck/keymaps/handwired_binaryplease')
| -rw-r--r-- | keyboards/planck/keymaps/handwired_binaryplease/config.h | 36 | ||||
| -rw-r--r-- | keyboards/planck/keymaps/handwired_binaryplease/rules.mk | 72 |
2 files changed, 9 insertions, 99 deletions
diff --git a/keyboards/planck/keymaps/handwired_binaryplease/config.h b/keyboards/planck/keymaps/handwired_binaryplease/config.h index 8cd4fe40a9..abf9f5771f 100644 --- a/keyboards/planck/keymaps/handwired_binaryplease/config.h +++ b/keyboards/planck/keymaps/handwired_binaryplease/config.h @@ -1,37 +1,11 @@ -#ifndef CONFIG_USER_H -#define CONFIG_USER_H +#pragma once -#include "../../config.h" - -/* USB Device descriptor parameter */ - - - -#undef VENDOR_ID -#undef PRODUCT_ID #undef MANUFACTURER +#define MANUFACTURER binaryplease #undef PRODUCT -#undef MATRIX_ROW_PINS -#undef MATRIX_COL_PINS -#undef UNUSED_PINS -#undef BACKLIGHT_PIN -#undef BACKLIGHT_LEVELS - - - -#define VENDOR_ID 0xFEED -#define PRODUCT_ID 0x6060 -#define MANUFACTURER binaryplease -#define PRODUCT Teensy_Planck +#define PRODUCT Teensy_Planck +#undef MATRIX_ROW_PINS #define MATRIX_ROW_PINS { D3, D2, D1, D0 } +#undef MATRIX_COL_PINS #define MATRIX_COL_PINS { F0, F1, F4, F5, F6, F7, B6, B5, B4, D7, D6, D4 } -#define UNUSED_PINS - -#define BACKLIGHT_PIN B7 - -/* number of backlight levels */ -#define BACKLIGHT_LEVELS 0 - - -#endif diff --git a/keyboards/planck/keymaps/handwired_binaryplease/rules.mk b/keyboards/planck/keymaps/handwired_binaryplease/rules.mk index cf37fa6f3b..459c7bce6c 100644 --- a/keyboards/planck/keymaps/handwired_binaryplease/rules.mk +++ b/keyboards/planck/keymaps/handwired_binaryplease/rules.mk @@ -1,68 +1,4 @@ -# MCU name -MCU = atmega32u4 - -# Processor frequency. -# This will define a symbol, F_CPU, in all source code files equal to the -# processor frequency in Hz. You can then use this symbol in your source code to -# calculate timings. Do NOT tack on a 'UL' at the end, this will be done -# automatically to create a 32-bit value in your source code. -# -# This will be an integer division of F_USB below, as it is sourced by -# F_USB after it has run through any CPU prescalers. Note that this value -# does not *change* the processor frequency - it should merely be updated to -# reflect the processor speed set externally so that the code can use accurate -# software delays. -F_CPU = 16000000 - -# -# LUFA specific -# -# Target architecture (see library "Board Types" documentation). -ARCH = AVR8 - -# Input clock frequency. -# This will define a symbol, F_USB, in all source code files equal to the -# input clock frequency (before any prescaling is performed) in Hz. This value may -# differ from F_CPU if prescaling is used on the latter, and is required as the -# raw input clock is fed directly to the PLL sections of the AVR for high speed -# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' -# at the end, this will be done automatically to create a 32-bit value in your -# source code. -# -# If no clock division is performed on the input clock inside the AVR (via the -# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. -F_USB = $(F_CPU) - -# Interrupt driven control endpoint task(+60) -OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT - - -# Boot Section Size in *bytes* -# Teensy halfKay 512 -# Teensy++ halfKay 1024 -# Atmel DFU loader 4096 -# LUFA bootloader 4096 -# USBaspLoader 2048 -OPT_DEFS += -DBOOTLOADER_SIZE=4096 - -# Build Options -# change to "no" to disable the options, or define them in the Makefile in -# the appropriate keymap folder that will get included automatically -# -BOOTMAGIC_ENABLE = no # Virtual DIP switch configuration(+1000) -MOUSEKEY_ENABLE = no # Mouse keys(+4700) -EXTRAKEY_ENABLE = yes # Audio control and System control(+450) -CONSOLE_ENABLE = no # Console for debug(+400) -COMMAND_ENABLE = no # Commands for debug and configuration -NKRO_ENABLE = no # Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work -BACKLIGHT_ENABLE = no # Enable keyboard backlight functionality -MIDI_ENABLE = yes # MIDI controls -AUDIO_ENABLE = no # Audio output on port C6 -UNICODE_ENABLE = no # Unicode -BLUETOOTH_ENABLE = no # Enable Bluetooth with the Adafruit EZ-Key HID -RGBLIGHT_ENABLE = no # Enable WS2812 RGB underlight. -API_SYSEX_ENABLE = no - -# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE -SLEEP_LED_ENABLE = no # Breathing sleep LED during USB suspend - +CONSOLE_ENABLE = no +NKRO_ENABLE = no +MIDI_ENABLE = yes +AUDIO_ENABLE = no |