diff options
Diffstat (limited to 'keyboards/naked48/rules.mk')
| -rw-r--r-- | keyboards/naked48/rules.mk | 66 |
1 files changed, 17 insertions, 49 deletions
diff --git a/keyboards/naked48/rules.mk b/keyboards/naked48/rules.mk index 53e2dfc21c..4427284e7f 100644 --- a/keyboards/naked48/rules.mk +++ b/keyboards/naked48/rules.mk @@ -1,46 +1,14 @@ -# SRC += i2c.c -QUANTUM_LIB_SRC += serial.c -# SRC += ssd1306.c - # MCU name MCU = atmega32u4 -# Processor frequency. -# This will define a symbol, F_CPU, in all source code files equal to the -# processor frequency in Hz. You can then use this symbol in your source code to -# calculate timings. Do NOT tack on a 'UL' at the end, this will be done -# automatically to create a 32-bit value in your source code. -# -# This will be an integer division of F_USB below, as it is sourced by -# F_USB after it has run through any CPU prescalers. Note that this value -# does not *change* the processor frequency - it should merely be updated to -# reflect the processor speed set externally so that the code can use accurate -# software delays. -F_CPU = 16000000 - -# -# LUFA specific -# -# Target architecture (see library "Board Types" documentation). -ARCH = AVR8 - -# Input clock frequency. -# This will define a symbol, F_USB, in all source code files equal to the -# input clock frequency (before any prescaling is performed) in Hz. This value may -# differ from F_CPU if prescaling is used on the latter, and is required as the -# raw input clock is fed directly to the PLL sections of the AVR for high speed -# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' -# at the end, this will be done automatically to create a 32-bit value in your -# source code. -# -# If no clock division is performed on the input clock inside the AVR (via the -# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. -F_USB = $(F_CPU) - -# Bootloader -# This definition is optional, and if your keyboard supports multiple bootloaders of -# different sizes, comment this out, and the correct address will be loaded -# automatically (+60). See bootloader.mk for all options. +# Bootloader selection +# Teensy halfkay +# Pro Micro caterina +# Atmel DFU atmel-dfu +# LUFA DFU lufa-dfu +# QMK DFU qmk-dfu +# ATmega32A bootloadHID +# ATmega328P USBasp BOOTLOADER = caterina # Interrupt driven control endpoint task(+60) @@ -51,22 +19,22 @@ OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT # the appropriate keymap folder that will get included automatically # BOOTMAGIC_ENABLE = no # Virtual DIP switch configuration(+1000) -MOUSEKEY_ENABLE = no # Mouse keys(+4700) -EXTRAKEY_ENABLE = no # Audio control and System control(+450) +MOUSEKEY_ENABLE = no # Mouse keys(+4700) +EXTRAKEY_ENABLE = yes # Audio control and System control(+450) CONSOLE_ENABLE = no # Console for debug(+400) -COMMAND_ENABLE = no # Commands for debug and configuration +COMMAND_ENABLE = yes # Commands for debug and configuration NKRO_ENABLE = no # Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work -BACKLIGHT_ENABLE = no # Enable keyboard backlight functionality +BACKLIGHT_ENABLE = no # Enable keyboard backlight functionality MIDI_ENABLE = no # MIDI controls AUDIO_ENABLE = no # Audio output on port C6 UNICODE_ENABLE = no # Unicode BLUETOOTH_ENABLE = no # Enable Bluetooth with the Adafruit EZ-Key HID -RGBLIGHT_ENABLE = no # Enable WS2812 RGB underlight. -SUBPROJECT_rev1 = no -USE_I2C = no +RGBLIGHT_ENABLE = yes # Enable WS2812 RGB underlight. +OLED_DRIVER_ENABLE = no +# USE_I2C = yes # Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE -SLEEP_LED_ENABLE = no # Breathing sleep LED during USB suspend +SLEEP_LED_ENABLE = no # Breathing sleep LED during USB suspend -CUSTOM_MATRIX = yes +SPLIT_KEYBOARD = yes DEFAULT_FOLDER = naked48/rev1 |