diff options
Diffstat (limited to 'keyboards/massdrop/ctrl/config.h')
| -rw-r--r-- | keyboards/massdrop/ctrl/config.h | 176 |
1 files changed, 0 insertions, 176 deletions
diff --git a/keyboards/massdrop/ctrl/config.h b/keyboards/massdrop/ctrl/config.h deleted file mode 100644 index 77967e17d3..0000000000 --- a/keyboards/massdrop/ctrl/config.h +++ /dev/null @@ -1,176 +0,0 @@ -/* -Copyright 2015 Jun Wako <wakojun@gmail.com> - -This program is free software: you can redistribute it and/or modify -it under the terms of the GNU General Public License as published by -the Free Software Foundation, either version 2 of the License, or -(at your option) any later version. - -This program is distributed in the hope that it will be useful, -but WITHOUT ANY WARRANTY; without even the implied warranty of -MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the -GNU General Public License for more details. - -You should have received a copy of the GNU General Public License -along with this program. If not, see <http://www.gnu.org/licenses/>. -*/ - -#pragma once - -#include "config_common.h" - -/* USB Device descriptor parameter */ -#define SERIAL_NUM "Unavailable" - -/* key matrix size */ -#define MATRIX_ROWS 11 -#define MATRIX_COLS 8 - -#define MATRIX_ROW_PINS { B04, B05, B06, B07, B08, B09, A10, A11, B10, B11, B12 } -#define MATRIX_COL_PINS { A00, A01, A02, A03, A04, A05, A06, A07 } - -/* COL2ROW, ROW2COL */ -#define DIODE_DIRECTION COL2ROW - -/* Temporary solution for matrix delay */ -#define IGNORE_ATOMIC_BLOCK - -/* Avoid out-of-bounds errors when SmartEEPROM is not enabled */ -#define EEPROM_SIZE 1024 - -/* MCU Port name definitions */ -#define PA 0 -#define PB 1 - -/* This Shift Register expands available hardware output lines to control additional peripherals */ -/* It uses four lines from the MCU to provide 16 output lines */ -/* Shift Register Clock configuration (MCU to ShiftRegister.RCLK) */ -#define SR_EXP_RCLK_PIN B14 -/* Shift Register Output Enable configuration (MCU to ShiftRegister.OE_N) */ -#define SR_EXP_OE_PIN B15 -/* SERCOM port to use for Shift Register SPI */ -/* DATAOUT and SCLK must be configured to use hardware pins of this port */ -#define SPI_SERCOM SERCOM2 -/* Shift Register SPI Data Out configuration (MCU.SERCOMx.PAD[0] to ShiftRegister.SER) */ -#define SPI_DATAOUT_PIN A12 -#define SPI_DATAOUT_MUX 2 -/* Shift Register SPI Serial Clock configuration (MCU.SERCOMx.PAD[1] to ShiftRegister.SRCLK) */ -#define SPI_SCLK_PIN A13 -#define SPI_SCLK_MUX 2 - -/* Debug LED (Small LED Located near MCU) */ -#define DEBUG_LED_ENABLE 1 -#define DEBUG_LED_PORT PA -#define DEBUG_LED_PIN 27 - -/* Additional debugging ports */ -/* PCB M21 */ -#define DEBUG_PORT1_ENABLE 1 -#define DEBUG_PORT1_PORT PB -#define DEBUG_PORT1_PIN 3 -/* PCB M23 */ -#define DEBUG_PORT2_ENABLE 1 -#define DEBUG_PORT2_PORT PB -#define DEBUG_PORT2_PIN 17 -/* PCB M25 */ -#define DEBUG_PORT3_ENABLE 1 -#define DEBUG_PORT3_PORT PA -#define DEBUG_PORT3_PIN 20 - -/* Debug Boot Tracing - During boot sequence, ground this pin to halt and display debug code using Debug LED */ -/* This is useful in determining which hardware device may have malfunctioned or is improperly configured */ -/* Feature is automatically disabled after successful boot */ -/* PCB M27 */ -#define DEBUG_BOOT_TRACING_ENABLE 1 -#define DEBUG_BOOT_TRACING_PORT PB -#define DEBUG_BOOT_TRACING_PIN 23 - -/* USB2422 config */ -#define USB2422_ADDRESS 0x58 -#define USB2422_VENDOR_ID 0x04D8 -#define USB2422_PRODUCT_ID 0xEEC5 -#define USB2422_DEVICE_VER 0x0101 -#define USB2422_MANUFACTURER "Massdrop Inc." -#define USB2422_PRODUCT "Massdrop Hub" -#define USB2422_ACTIVE_PIN A18 - -/* Debounce reduces chatter (unintended double-presses) - set 0 if debouncing is not needed */ -#define DEBOUNCE 5 - -/* Mechanical locking support. Use KC_LCAP, KC_LNUM or KC_LSCR instead in keymap */ -//#define LOCKING_SUPPORT_ENABLE -/* Locking resynchronize hack */ -//#define LOCKING_RESYNC_ENABLE - -/* Force boot in NKRO mode */ -//#define FORCE_NKRO - -/* - * Feature disable options - * These options are also useful to firmware size reduction. - */ - -/* disable debug print */ -//#define NO_DEBUG - -/* disable print */ -//#define NO_PRINT - -/* disable action features */ -//#define NO_ACTION_LAYER -//#define NO_ACTION_TAPPING -//#define NO_ACTION_ONESHOT - -#define RGB_MATRIX_KEYPRESSES -#define RGB_MATRIX_LED_PROCESS_LIMIT 15 -#define RGB_MATRIX_LED_FLUSH_LIMIT 10 -// RGB Matrix Animation modes. Explicitly enabled -// For full list of effects, see: -// https://docs.qmk.fm/#/feature_rgb_matrix?id=rgb-matrix-effects -# define ENABLE_RGB_MATRIX_ALPHAS_MODS -# define ENABLE_RGB_MATRIX_GRADIENT_UP_DOWN -# define ENABLE_RGB_MATRIX_GRADIENT_LEFT_RIGHT -# define ENABLE_RGB_MATRIX_BREATHING -# define ENABLE_RGB_MATRIX_BAND_SAT -# define ENABLE_RGB_MATRIX_BAND_VAL -# define ENABLE_RGB_MATRIX_BAND_PINWHEEL_SAT -# define ENABLE_RGB_MATRIX_BAND_PINWHEEL_VAL -# define ENABLE_RGB_MATRIX_BAND_SPIRAL_SAT -# define ENABLE_RGB_MATRIX_BAND_SPIRAL_VAL -# define ENABLE_RGB_MATRIX_CYCLE_ALL -# define ENABLE_RGB_MATRIX_CYCLE_LEFT_RIGHT -# define ENABLE_RGB_MATRIX_CYCLE_UP_DOWN -# define ENABLE_RGB_MATRIX_RAINBOW_MOVING_CHEVRON -# define ENABLE_RGB_MATRIX_CYCLE_OUT_IN -# define ENABLE_RGB_MATRIX_CYCLE_OUT_IN_DUAL -# define ENABLE_RGB_MATRIX_CYCLE_PINWHEEL -# define ENABLE_RGB_MATRIX_CYCLE_SPIRAL -# define ENABLE_RGB_MATRIX_DUAL_BEACON -# define ENABLE_RGB_MATRIX_RAINBOW_BEACON -# define ENABLE_RGB_MATRIX_RAINBOW_PINWHEELS -# define ENABLE_RGB_MATRIX_RAINDROPS -# define ENABLE_RGB_MATRIX_JELLYBEAN_RAINDROPS -# define ENABLE_RGB_MATRIX_HUE_BREATHING -# define ENABLE_RGB_MATRIX_HUE_PENDULUM -# define ENABLE_RGB_MATRIX_HUE_WAVE -# define ENABLE_RGB_MATRIX_PIXEL_RAIN -# define ENABLE_RGB_MATRIX_PIXEL_FLOW -# define ENABLE_RGB_MATRIX_PIXEL_FRACTAL -// enabled only if RGB_MATRIX_FRAMEBUFFER_EFFECTS is defined -# define ENABLE_RGB_MATRIX_TYPING_HEATMAP -# define ENABLE_RGB_MATRIX_DIGITAL_RAIN -// enabled only of RGB_MATRIX_KEYPRESSES or RGB_MATRIX_KEYRELEASES is defined -# define ENABLE_RGB_MATRIX_SOLID_REACTIVE_SIMPLE -# define ENABLE_RGB_MATRIX_SOLID_REACTIVE -# define ENABLE_RGB_MATRIX_SOLID_REACTIVE_WIDE -# define ENABLE_RGB_MATRIX_SOLID_REACTIVE_MULTIWIDE -# define ENABLE_RGB_MATRIX_SOLID_REACTIVE_CROSS -# define ENABLE_RGB_MATRIX_SOLID_REACTIVE_MULTICROSS -# define ENABLE_RGB_MATRIX_SOLID_REACTIVE_NEXUS -# define ENABLE_RGB_MATRIX_SOLID_REACTIVE_MULTINEXUS -# define ENABLE_RGB_MATRIX_SPLASH -# define ENABLE_RGB_MATRIX_MULTISPLASH -# define ENABLE_RGB_MATRIX_SOLID_SPLASH -# define ENABLE_RGB_MATRIX_SOLID_MULTISPLASH - -#include "config_led.h" |