diff options
Diffstat (limited to 'keyboards/keebio')
21 files changed, 126 insertions, 365 deletions
diff --git a/keyboards/keebio/bdn9/rules.mk b/keyboards/keebio/bdn9/rules.mk index 3ab8491089..8b4bb334eb 100644 --- a/keyboards/keebio/bdn9/rules.mk +++ b/keyboards/keebio/bdn9/rules.mk @@ -1,11 +1,5 @@ +# MCU name MCU = atmega32u4 -F_CPU = 16000000 -ARCH = AVR8 -F_USB = $(F_CPU) - -# Interrupt driven control endpoint task(+60) -OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT - # Bootloader selection # Teensy halfkay @@ -13,20 +7,10 @@ OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT # Atmel DFU atmel-dfu # LUFA DFU lufa-dfu # QMK DFU qmk-dfu -# atmega32a bootloadHID +# ATmega32A bootloadHID +# ATmega328P USBasp BOOTLOADER = caterina - -# If you don't know the bootloader type, then you can specify the -# Boot Section Size in *bytes* by uncommenting out the OPT_DEFS line -# Teensy halfKay 512 -# Teensy++ halfKay 1024 -# Atmel DFU loader 4096 -# LUFA bootloader 4096 -# USBaspLoader 2048 -# OPT_DEFS += -DBOOTLOADER_SIZE=4096 - - # Build Options # change yes to no to disable # diff --git a/keyboards/keebio/bfo9000/rules.mk b/keyboards/keebio/bfo9000/rules.mk index 931a0f5e95..c0f4ed42dd 100644 --- a/keyboards/keebio/bfo9000/rules.mk +++ b/keyboards/keebio/bfo9000/rules.mk @@ -1,47 +1,16 @@ # MCU name MCU = atmega32u4 -# Processor frequency. -# This will define a symbol, F_CPU, in all source code files equal to the -# processor frequency in Hz. You can then use this symbol in your source code to -# calculate timings. Do NOT tack on a 'UL' at the end, this will be done -# automatically to create a 32-bit value in your source code. -# -# This will be an integer division of F_USB below, as it is sourced by -# F_USB after it has run through any CPU prescalers. Note that this value -# does not *change* the processor frequency - it should merely be updated to -# reflect the processor speed set externally so that the code can use accurate -# software delays. -F_CPU = 16000000 - -# -# LUFA specific -# -# Target architecture (see library "Board Types" documentation). -ARCH = AVR8 - -# Input clock frequency. -# This will define a symbol, F_USB, in all source code files equal to the -# input clock frequency (before any prescaling is performed) in Hz. This value may -# differ from F_CPU if prescaling is used on the latter, and is required as the -# raw input clock is fed directly to the PLL sections of the AVR for high speed -# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' -# at the end, this will be done automatically to create a 32-bit value in your -# source code. -# -# If no clock division is performed on the input clock inside the AVR (via the -# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. -F_USB = $(F_CPU) - -# Bootloader -# This definition is optional, and if your keyboard supports multiple bootloaders of -# different sizes, comment this out, and the correct address will be loaded -# automatically (+60). See bootloader.mk for all options. +# Bootloader selection +# Teensy halfkay +# Pro Micro caterina +# Atmel DFU atmel-dfu +# LUFA DFU lufa-dfu +# QMK DFU qmk-dfu +# ATmega32A bootloadHID +# ATmega328P USBasp BOOTLOADER = caterina -# Interrupt driven control endpoint task(+60) -OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT - # Build Options # change to "no" to disable the options, or define them in the Makefile in # the appropriate keymap folder that will get included automatically diff --git a/keyboards/keebio/chocopad/keymaps/default/rules.mk b/keyboards/keebio/chocopad/keymaps/default/rules.mk deleted file mode 100644 index a81250cdf6..0000000000 --- a/keyboards/keebio/chocopad/keymaps/default/rules.mk +++ /dev/null @@ -1,2 +0,0 @@ -RGBLIGHT_ENABLE = yes - diff --git a/keyboards/keebio/chocopad/rules.mk b/keyboards/keebio/chocopad/rules.mk index 39ce38e100..ac68b66523 100644 --- a/keyboards/keebio/chocopad/rules.mk +++ b/keyboards/keebio/chocopad/rules.mk @@ -1,45 +1,15 @@ # MCU name MCU = atmega32u4 -# Processor frequency. -# This will define a symbol, F_CPU, in all source code files equal to the -# processor frequency in Hz. You can then use this symbol in your source code to -# calculate timings. Do NOT tack on a 'UL' at the end, this will be done -# automatically to create a 32-bit value in your source code. -# -# This will be an integer division of F_USB below, as it is sourced by -# F_USB after it has run through any CPU prescalers. Note that this value -# does not *change* the processor frequency - it should merely be updated to -# reflect the processor speed set externally so that the code can use accurate -# software delays. -F_CPU = 16000000 - -# -# LUFA specific -# -# Target architecture (see library "Board Types" documentation). -ARCH = AVR8 - -# Input clock frequency. -# This will define a symbol, F_USB, in all source code files equal to the -# input clock frequency (before any prescaling is performed) in Hz. This value may -# differ from F_CPU if prescaling is used on the latter, and is required as the -# raw input clock is fed directly to the PLL sections of the AVR for high speed -# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' -# at the end, this will be done automatically to create a 32-bit value in your -# source code. -# -# If no clock division is performed on the input clock inside the AVR (via the -# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. -F_USB = $(F_CPU) - -# Interrupt driven control endpoint task(+60) -OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT - - -# Boot Section Size in *bytes* -OPT_DEFS += -DBOOTLOADER_SIZE=4096 - +# Bootloader selection +# Teensy halfkay +# Pro Micro caterina +# Atmel DFU atmel-dfu +# LUFA DFU lufa-dfu +# QMK DFU qmk-dfu +# ATmega32A bootloadHID +# ATmega328P USBasp +BOOTLOADER = caterina # Build Options # comment out to disable the options. diff --git a/keyboards/keebio/dilly/rules.mk b/keyboards/keebio/dilly/rules.mk index 812362567e..14f62bd8f7 100644 --- a/keyboards/keebio/dilly/rules.mk +++ b/keyboards/keebio/dilly/rules.mk @@ -1,45 +1,15 @@ # MCU name MCU = atmega32u4 -# Processor frequency. -# This will define a symbol, F_CPU, in all source code files equal to the -# processor frequency in Hz. You can then use this symbol in your source code to -# calculate timings. Do NOT tack on a 'UL' at the end, this will be done -# automatically to create a 32-bit value in your source code. -# -# This will be an integer division of F_USB below, as it is sourced by -# F_USB after it has run through any CPU prescalers. Note that this value -# does not *change* the processor frequency - it should merely be updated to -# reflect the processor speed set externally so that the code can use accurate -# software delays. -F_CPU = 16000000 - -# -# LUFA specific -# -# Target architecture (see library "Board Types" documentation). -ARCH = AVR8 - -# Input clock frequency. -# This will define a symbol, F_USB, in all source code files equal to the -# input clock frequency (before any prescaling is performed) in Hz. This value may -# differ from F_CPU if prescaling is used on the latter, and is required as the -# raw input clock is fed directly to the PLL sections of the AVR for high speed -# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' -# at the end, this will be done automatically to create a 32-bit value in your -# source code. -# -# If no clock division is performed on the input clock inside the AVR (via the -# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. -F_USB = $(F_CPU) - -# Interrupt driven control endpoint task(+60) -OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT - - -# Boot Section Size in *bytes* -OPT_DEFS += -DBOOTLOADER_SIZE=4096 - +# Bootloader selection +# Teensy halfkay +# Pro Micro caterina +# Atmel DFU atmel-dfu +# LUFA DFU lufa-dfu +# QMK DFU qmk-dfu +# ATmega32A bootloadHID +# ATmega328P USBasp +BOOTLOADER = caterina # Build Options # comment out to disable the options. diff --git a/keyboards/keebio/ergodicity/rules.mk b/keyboards/keebio/ergodicity/rules.mk index 974f75afdf..0c794fb751 100644 --- a/keyboards/keebio/ergodicity/rules.mk +++ b/keyboards/keebio/ergodicity/rules.mk @@ -1,63 +1,16 @@ # MCU name MCU = atmega32u4 -# Processor frequency. -# This will define a symbol, F_CPU, in all source code files equal to the -# processor frequency in Hz. You can then use this symbol in your source code to -# calculate timings. Do NOT tack on a 'UL' at the end, this will be done -# automatically to create a 32-bit value in your source code. -# -# This will be an integer division of F_USB below, as it is sourced by -# F_USB after it has run through any CPU prescalers. Note that this value -# does not *change* the processor frequency - it should merely be updated to -# reflect the processor speed set externally so that the code can use accurate -# software delays. -F_CPU = 16000000 - - -# -# LUFA specific -# -# Target architecture (see library "Board Types" documentation). -ARCH = AVR8 - -# Input clock frequency. -# This will define a symbol, F_USB, in all source code files equal to the -# input clock frequency (before any prescaling is performed) in Hz. This value may -# differ from F_CPU if prescaling is used on the latter, and is required as the -# raw input clock is fed directly to the PLL sections of the AVR for high speed -# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' -# at the end, this will be done automatically to create a 32-bit value in your -# source code. -# -# If no clock division is performed on the input clock inside the AVR (via the -# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. -F_USB = $(F_CPU) - -# Interrupt driven control endpoint task(+60) -OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT - - # Bootloader selection # Teensy halfkay # Pro Micro caterina # Atmel DFU atmel-dfu # LUFA DFU lufa-dfu # QMK DFU qmk-dfu -# atmega32a bootloadHID +# ATmega32A bootloadHID +# ATmega328P USBasp BOOTLOADER = atmel-dfu - -# If you don't know the bootloader type, then you can specify the -# Boot Section Size in *bytes* by uncommenting out the OPT_DEFS line -# Teensy halfKay 512 -# Teensy++ halfKay 1024 -# Atmel DFU loader 4096 -# LUFA bootloader 4096 -# USBaspLoader 2048 -# OPT_DEFS += -DBOOTLOADER_SIZE=4096 - - # Build Options # change yes to no to disable # diff --git a/keyboards/keebio/fourier/keymaps/default/rules.mk b/keyboards/keebio/fourier/keymaps/default/rules.mk deleted file mode 100644 index e69de29bb2..0000000000 --- a/keyboards/keebio/fourier/keymaps/default/rules.mk +++ /dev/null diff --git a/keyboards/keebio/fourier/rules.mk b/keyboards/keebio/fourier/rules.mk index 9512c0f648..9bd9e1dccc 100644 --- a/keyboards/keebio/fourier/rules.mk +++ b/keyboards/keebio/fourier/rules.mk @@ -1,47 +1,16 @@ # MCU name MCU = atmega32u4 -# Processor frequency. -# This will define a symbol, F_CPU, in all source code files equal to the -# processor frequency in Hz. You can then use this symbol in your source code to -# calculate timings. Do NOT tack on a 'UL' at the end, this will be done -# automatically to create a 32-bit value in your source code. -# -# This will be an integer division of F_USB below, as it is sourced by -# F_USB after it has run through any CPU prescalers. Note that this value -# does not *change* the processor frequency - it should merely be updated to -# reflect the processor speed set externally so that the code can use accurate -# software delays. -F_CPU = 16000000 - -# -# LUFA specific -# -# Target architecture (see library "Board Types" documentation). -ARCH = AVR8 - -# Input clock frequency. -# This will define a symbol, F_USB, in all source code files equal to the -# input clock frequency (before any prescaling is performed) in Hz. This value may -# differ from F_CPU if prescaling is used on the latter, and is required as the -# raw input clock is fed directly to the PLL sections of the AVR for high speed -# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' -# at the end, this will be done automatically to create a 32-bit value in your -# source code. -# -# If no clock division is performed on the input clock inside the AVR (via the -# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. -F_USB = $(F_CPU) - -# Bootloader -# This definition is optional, and if your keyboard supports multiple bootloaders of -# different sizes, comment this out, and the correct address will be loaded -# automatically (+60). See bootloader.mk for all options. +# Bootloader selection +# Teensy halfkay +# Pro Micro caterina +# Atmel DFU atmel-dfu +# LUFA DFU lufa-dfu +# QMK DFU qmk-dfu +# ATmega32A bootloadHID +# ATmega328P USBasp BOOTLOADER = caterina -# Interrupt driven control endpoint task(+60) -OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT - # Build Options # change to "no" to disable the options, or define them in the Makefile in # the appropriate keymap folder that will get included automatically diff --git a/keyboards/keebio/iris/rules.mk b/keyboards/keebio/iris/rules.mk index 83b13b1603..ed730b02b2 100644 --- a/keyboards/keebio/iris/rules.mk +++ b/keyboards/keebio/iris/rules.mk @@ -1,12 +1,14 @@ +# MCU name MCU = atmega32u4 -F_CPU = 16000000 -ARCH = AVR8 -F_USB = $(F_CPU) -# Bootloader -# This definition is optional, and if your keyboard supports multiple bootloaders of -# different sizes, comment this out, and the correct address will be loaded -# automatically (+60). See bootloader.mk for all options. +# Bootloader selection +# Teensy halfkay +# Pro Micro caterina +# Atmel DFU atmel-dfu +# LUFA DFU lufa-dfu +# QMK DFU qmk-dfu +# ATmega32A bootloadHID +# ATmega328P USBasp ifneq (, $(findstring rev3, $(KEYBOARD))) BOOTLOADER = qmk-dfu else ifneq (, $(findstring rev4, $(KEYBOARD))) @@ -15,9 +17,6 @@ else BOOTLOADER = caterina endif -# Interrupt driven control endpoint task(+60) -OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT - # Build Options # change to "no" to disable the options, or define them in the Makefile in # the appropriate keymap folder that will get included automatically diff --git a/keyboards/keebio/laplace/keymaps/default/rules.mk b/keyboards/keebio/laplace/keymaps/default/rules.mk deleted file mode 100644 index e69de29bb2..0000000000 --- a/keyboards/keebio/laplace/keymaps/default/rules.mk +++ /dev/null diff --git a/keyboards/keebio/laplace/rules.mk b/keyboards/keebio/laplace/rules.mk index 7f896e1bd5..01efe96f65 100644 --- a/keyboards/keebio/laplace/rules.mk +++ b/keyboards/keebio/laplace/rules.mk @@ -1,49 +1,15 @@ # MCU name MCU = atmega32u4 -# Processor frequency. -# This will define a symbol, F_CPU, in all source code files equal to the -# processor frequency in Hz. You can then use this symbol in your source code to -# calculate timings. Do NOT tack on a 'UL' at the end, this will be done -# automatically to create a 32-bit value in your source code. -# -# This will be an integer division of F_USB below, as it is sourced by -# F_USB after it has run through any CPU prescalers. Note that this value -# does not *change* the processor frequency - it should merely be updated to -# reflect the processor speed set externally so that the code can use accurate -# software delays. -F_CPU = 16000000 - -# -# LUFA specific -# -# Target architecture (see library "Board Types" documentation). -ARCH = AVR8 - -# Input clock frequency. -# This will define a symbol, F_USB, in all source code files equal to the -# input clock frequency (before any prescaling is performed) in Hz. This value may -# differ from F_CPU if prescaling is used on the latter, and is required as the -# raw input clock is fed directly to the PLL sections of the AVR for high speed -# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' -# at the end, this will be done automatically to create a 32-bit value in your -# source code. -# -# If no clock division is performed on the input clock inside the AVR (via the -# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. -F_USB = $(F_CPU) - -# Interrupt driven control endpoint task(+60) -OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT - - -# Boot Section Size in *bytes* -# Teensy halfKay 512 -# Teensy++ halfKay 1024 -# Atmel DFU loader 4096 -# LUFA bootloader 4096 -# USBaspLoader 2048 -OPT_DEFS += -DBOOTLOADER_SIZE=4096 +# Bootloader selection +# Teensy halfkay +# Pro Micro caterina +# Atmel DFU atmel-dfu +# LUFA DFU lufa-dfu +# QMK DFU qmk-dfu +# ATmega32A bootloadHID +# ATmega328P USBasp +BOOTLOADER = caterina # Build Options # change to "no" to disable the options, or define them in the Makefile in diff --git a/keyboards/keebio/levinson/rules.mk b/keyboards/keebio/levinson/rules.mk index cdaef48890..c7446445f3 100644 --- a/keyboards/keebio/levinson/rules.mk +++ b/keyboards/keebio/levinson/rules.mk @@ -1,11 +1,15 @@ +# MCU name MCU = atmega32u4 -F_CPU = 16000000 -ARCH = AVR8 -F_USB = $(F_CPU) -BOOTLOADER = caterina -# Interrupt driven control endpoint task(+60) -OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT +# Bootloader selection +# Teensy halfkay +# Pro Micro caterina +# Atmel DFU atmel-dfu +# LUFA DFU lufa-dfu +# QMK DFU qmk-dfu +# ATmega32A bootloadHID +# ATmega328P USBasp +BOOTLOADER = caterina # Build Options # change to "no" to disable the options, or define them in the Makefile in diff --git a/keyboards/keebio/nyquist/rules.mk b/keyboards/keebio/nyquist/rules.mk index ea4053763c..bf3b676219 100644 --- a/keyboards/keebio/nyquist/rules.mk +++ b/keyboards/keebio/nyquist/rules.mk @@ -1,51 +1,20 @@ # MCU name MCU = atmega32u4 -# Processor frequency. -# This will define a symbol, F_CPU, in all source code files equal to the -# processor frequency in Hz. You can then use this symbol in your source code to -# calculate timings. Do NOT tack on a 'UL' at the end, this will be done -# automatically to create a 32-bit value in your source code. -# -# This will be an integer division of F_USB below, as it is sourced by -# F_USB after it has run through any CPU prescalers. Note that this value -# does not *change* the processor frequency - it should merely be updated to -# reflect the processor speed set externally so that the code can use accurate -# software delays. -F_CPU = 16000000 - -# -# LUFA specific -# -# Target architecture (see library "Board Types" documentation). -ARCH = AVR8 - -# Input clock frequency. -# This will define a symbol, F_USB, in all source code files equal to the -# input clock frequency (before any prescaling is performed) in Hz. This value may -# differ from F_CPU if prescaling is used on the latter, and is required as the -# raw input clock is fed directly to the PLL sections of the AVR for high speed -# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' -# at the end, this will be done automatically to create a 32-bit value in your -# source code. -# -# If no clock division is performed on the input clock inside the AVR (via the -# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. -F_USB = $(F_CPU) - -# Bootloader -# This definition is optional, and if your keyboard supports multiple bootloaders of -# different sizes, comment this out, and the correct address will be loaded -# automatically (+60). See bootloader.mk for all options. +# Bootloader selection +# Teensy halfkay +# Pro Micro caterina +# Atmel DFU atmel-dfu +# LUFA DFU lufa-dfu +# QMK DFU qmk-dfu +# ATmega32A bootloadHID +# ATmega328P USBasp ifneq (, $(findstring rev3, $(KEYBOARD))) BOOTLOADER = qmk-dfu else BOOTLOADER = caterina endif -# Interrupt driven control endpoint task(+60) -OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT - # Build Options # change to "no" to disable the options, or define them in the Makefile in # the appropriate keymap folder that will get included automatically diff --git a/keyboards/keebio/quefrency/keymaps/default/rules.mk b/keyboards/keebio/quefrency/keymaps/default/rules.mk deleted file mode 100644 index e69de29bb2..0000000000 --- a/keyboards/keebio/quefrency/keymaps/default/rules.mk +++ /dev/null diff --git a/keyboards/keebio/quefrency/keymaps/default65/rules.mk b/keyboards/keebio/quefrency/keymaps/default65/rules.mk deleted file mode 100644 index e69de29bb2..0000000000 --- a/keyboards/keebio/quefrency/keymaps/default65/rules.mk +++ /dev/null diff --git a/keyboards/keebio/quefrency/rules.mk b/keyboards/keebio/quefrency/rules.mk index c28696c08e..284a0def32 100644 --- a/keyboards/keebio/quefrency/rules.mk +++ b/keyboards/keebio/quefrency/rules.mk @@ -1,11 +1,15 @@ +# MCU name MCU = atmega32u4 -F_CPU = 16000000 -ARCH = AVR8 -F_USB = $(F_CPU) -BOOTLOADER = caterina -# Interrupt driven control endpoint task(+60) -OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT +# Bootloader selection +# Teensy halfkay +# Pro Micro caterina +# Atmel DFU atmel-dfu +# LUFA DFU lufa-dfu +# QMK DFU qmk-dfu +# ATmega32A bootloadHID +# ATmega328P USBasp +BOOTLOADER = caterina # Build Options # change to "no" to disable the options, or define them in the Makefile in diff --git a/keyboards/keebio/rorschach/rules.mk b/keyboards/keebio/rorschach/rules.mk index b500740522..f6007e4422 100644 --- a/keyboards/keebio/rorschach/rules.mk +++ b/keyboards/keebio/rorschach/rules.mk @@ -1,10 +1,15 @@ # MCU name MCU = atmega32u4 -F_CPU = 16000000 -ARCH = AVR8 -F_USB = $(F_CPU) + +# Bootloader selection +# Teensy halfkay +# Pro Micro caterina +# Atmel DFU atmel-dfu +# LUFA DFU lufa-dfu +# QMK DFU qmk-dfu +# ATmega32A bootloadHID +# ATmega328P USBasp BOOTLOADER = caterina -OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT BOOTMAGIC_ENABLE = no # Virtual DIP switch configuration(+1000) MOUSEKEY_ENABLE = yes # Mouse keys(+4700) diff --git a/keyboards/keebio/tragicforce68/rules.mk b/keyboards/keebio/tragicforce68/rules.mk index a652f1fac6..2118d3fc27 100644 --- a/keyboards/keebio/tragicforce68/rules.mk +++ b/keyboards/keebio/tragicforce68/rules.mk @@ -1,11 +1,15 @@ +# MCU name MCU = atmega32u4 -F_CPU = 16000000 -ARCH = AVR8 -F_USB = $(F_CPU) -BOOTLOADER = caterina -# Interrupt driven control endpoint task(+60) -OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT +# Bootloader selection +# Teensy halfkay +# Pro Micro caterina +# Atmel DFU atmel-dfu +# LUFA DFU lufa-dfu +# QMK DFU qmk-dfu +# ATmega32A bootloadHID +# ATmega328P USBasp +BOOTLOADER = caterina # Build Options # change yes to no to disable diff --git a/keyboards/keebio/tukey/rules.mk b/keyboards/keebio/tukey/rules.mk index ab860459da..c74f169961 100644 --- a/keyboards/keebio/tukey/rules.mk +++ b/keyboards/keebio/tukey/rules.mk @@ -1,27 +1,16 @@ # MCU name MCU = atmega32u4 - # Bootloader selection # Teensy halfkay # Pro Micro caterina # Atmel DFU atmel-dfu # LUFA DFU lufa-dfu # QMK DFU qmk-dfu -# atmega32a bootloadHID +# ATmega32A bootloadHID +# ATmega328P USBasp BOOTLOADER = caterina - -# If you don't know the bootloader type, then you can specify the -# Boot Section Size in *bytes* by uncommenting out the OPT_DEFS line -# Teensy halfKay 512 -# Teensy++ halfKay 1024 -# Atmel DFU loader 4096 -# LUFA bootloader 4096 -# USBaspLoader 2048 -# OPT_DEFS += -DBOOTLOADER_SIZE=4096 - - # Build Options # change yes to no to disable # diff --git a/keyboards/keebio/viterbi/rules.mk b/keyboards/keebio/viterbi/rules.mk index 811f57fdbc..0759ab925e 100644 --- a/keyboards/keebio/viterbi/rules.mk +++ b/keyboards/keebio/viterbi/rules.mk @@ -1,11 +1,15 @@ +# MCU name MCU = atmega32u4 -F_CPU = 16000000 -ARCH = AVR8 -F_USB = $(F_CPU) -BOOTLOADER = caterina -# Interrupt driven control endpoint task(+60) -OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT +# Bootloader selection +# Teensy halfkay +# Pro Micro caterina +# Atmel DFU atmel-dfu +# LUFA DFU lufa-dfu +# QMK DFU qmk-dfu +# ATmega32A bootloadHID +# ATmega328P USBasp +BOOTLOADER = caterina # Build Options # change to "no" to disable the options, or define them in the Makefile in diff --git a/keyboards/keebio/wavelet/rules.mk b/keyboards/keebio/wavelet/rules.mk index cfff50a41d..f924db62b8 100644 --- a/keyboards/keebio/wavelet/rules.mk +++ b/keyboards/keebio/wavelet/rules.mk @@ -1,11 +1,15 @@ +# MCU name MCU = atmega32u4 -F_CPU = 16000000 -ARCH = AVR8 -F_USB = $(F_CPU) -BOOTLOADER = caterina -# Interrupt driven control endpoint task(+60) -OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT +# Bootloader selection +# Teensy halfkay +# Pro Micro caterina +# Atmel DFU atmel-dfu +# LUFA DFU lufa-dfu +# QMK DFU qmk-dfu +# ATmega32A bootloadHID +# ATmega328P USBasp +BOOTLOADER = caterina # Build Options # change to "no" to disable the options, or define them in the Makefile in |