diff options
Diffstat (limited to 'keyboards/jd45')
| -rw-r--r-- | keyboards/jd45/Makefile | 72 | ||||
| -rw-r--r-- | keyboards/jd45/keymaps/jeebak/config.h | 16 | ||||
| -rw-r--r-- | keyboards/jd45/keymaps/jeebak/keymap.c | 423 | ||||
| -rw-r--r-- | keyboards/jd45/keymaps/jeebak/readme.md | 129 | ||||
| -rw-r--r-- | keyboards/jd45/rules.mk | 67 |
5 files changed, 637 insertions, 70 deletions
diff --git a/keyboards/jd45/Makefile b/keyboards/jd45/Makefile index 75d544f16a..4e2a6f00fd 100644 --- a/keyboards/jd45/Makefile +++ b/keyboards/jd45/Makefile @@ -1,71 +1,3 @@ - - -# MCU name -#MCU = at90usb1287 -MCU = atmega32u4 - -# Processor frequency. -# This will define a symbol, F_CPU, in all source code files equal to the -# processor frequency in Hz. You can then use this symbol in your source code to -# calculate timings. Do NOT tack on a 'UL' at the end, this will be done -# automatically to create a 32-bit value in your source code. -# -# This will be an integer division of F_USB below, as it is sourced by -# F_USB after it has run through any CPU prescalers. Note that this value -# does not *change* the processor frequency - it should merely be updated to -# reflect the processor speed set externally so that the code can use accurate -# software delays. -F_CPU = 16000000 - - -# -# LUFA specific -# -# Target architecture (see library "Board Types" documentation). -ARCH = AVR8 - -# Input clock frequency. -# This will define a symbol, F_USB, in all source code files equal to the -# input clock frequency (before any prescaling is performed) in Hz. This value may -# differ from F_CPU if prescaling is used on the latter, and is required as the -# raw input clock is fed directly to the PLL sections of the AVR for high speed -# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' -# at the end, this will be done automatically to create a 32-bit value in your -# source code. -# -# If no clock division is performed on the input clock inside the AVR (via the -# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. -F_USB = $(F_CPU) - -# Interrupt driven control endpoint task(+60) -OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT - - -# Boot Section Size in *bytes* -# Teensy halfKay 512 -# Teensy++ halfKay 1024 -# Atmel DFU loader 4096 -# LUFA bootloader 4096 -# USBaspLoader 2048 -OPT_DEFS += -DBOOTLOADER_SIZE=4096 - - -# Build Options -# comment out to disable the options. -# -BOOTMAGIC_ENABLE ?= yes # Virtual DIP switch configuration(+1000) -MOUSEKEY_ENABLE ?= yes # Mouse keys(+4700) -EXTRAKEY_ENABLE ?= yes # Audio control and System control(+450) -CONSOLE_ENABLE ?= yes # Console for debug(+400) -COMMAND_ENABLE ?= yes # Commands for debug and configuration -# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE -# SLEEP_LED_ENABLE ?= yes # Breathing sleep LED during USB suspend -# NKRO_ENABLE ?= yes # USB Nkey Rollover - not yet supported in LUFA -BACKLIGHT_ENABLE ?= yes # Enable keyboard backlight functionality -MIDI_ENABLE ?= YES # MIDI controls -# UNICODE_ENABLE ?= YES # Unicode -BLUETOOTH_ENABLE ?= yes # Enable Bluetooth with the Adafruit EZ-Key HID - -ifndef QUANTUM_DIR +ifndef MAKEFILE_INCLUDED include ../../Makefile -endif +endif
\ No newline at end of file diff --git a/keyboards/jd45/keymaps/jeebak/config.h b/keyboards/jd45/keymaps/jeebak/config.h new file mode 100644 index 0000000000..53a1f0a307 --- /dev/null +++ b/keyboards/jd45/keymaps/jeebak/config.h @@ -0,0 +1,16 @@ +#include "../../config.h" + +/** + *JD45 keymap definition macro + */ +#define KEYMAP_JD45( \ + K01, K02, K03, K04, K05, K06, K07, K08, K09, K10, K11, K12, K13, \ + K14, K15, K16, K17, K18, K19, K20, K21, K22, K23, K24, K25, \ + K26, K27, K28, K29, K30, K31, K32, K33, K34, K35, K36, K37, \ + K38, K39, K40, K41, K42, K43, K44, K45, K46, K47 \ +) { \ + { K01, K02, K03, K04, K05, K06, K07, K08, K09, K10, K11, K12, K13 }, \ + { K14, K15, K16, K17, K18, K19, K20, K21, K22, K23, K24, K25, KC_NO }, \ + { K26, K27, K28, K29, K30, K31, K32, K33, K34, K35, K36, K37, KC_NO }, \ + { K38, K39, K40, K41, K42, KC_NO, K43, KC_NO, K44, K45, K46, K47, KC_NO } \ +} diff --git a/keyboards/jd45/keymaps/jeebak/keymap.c b/keyboards/jd45/keymaps/jeebak/keymap.c new file mode 100644 index 0000000000..8d26cbde12 --- /dev/null +++ b/keyboards/jd45/keymaps/jeebak/keymap.c @@ -0,0 +1,423 @@ +#include "jd45.h" + +extern keymap_config_t keymap_config; + +// Each layer gets a name for readability, which is then used in the keymap matrix below. +// The underscores don't mean anything - you can have a layer called STUFF or any other name. +// Layer names don't all need to be of the same length, obviously, and you can also skip them +// entirely and just use numbers. +#define _QWERTY 0 +#define _COLEMAK 1 +#define _DVORAK 2 +#define _LOWER 3 +#define _RAISE 4 +#define _PLOVER 5 +#define _TOUCHCURSOR 6 +#define _MOUSECURSOR 7 +#define _ADJUST 16 + +// Keycodes +enum planck_keycodes { + QWERTY = SAFE_RANGE, + COLEMAK, + DVORAK, + PLOVER, + LOWER, + RAISE, + BACKLIT, + EXT_PLV +}; + +enum macro_keycodes { + KC_ALT_TAB, + KC_CMD_TAB, + KC_CTL_TAB, + KC_CMD_SLSH, + KC_AG_FIND, + KC_AG_AGAIN, + KC_AG_UNDO, + KC_AG_CUT, + KC_AG_COPY, + KC_AG_PASTE, + KC_AG_DESK_L, + KC_AG_DESK_R, + KC_AG_TAB_C, + KC_AG_TAB_N, + KC_AG_TAB_R, +}; + +// Fillers to make layering more clear +#define _______ KC_TRNS +#define XXXXXXX KC_NO + +// Custom macros +#define CTL_ESC CTL_T(KC_ESC) // Tap for Esc, hold for Ctrl +#define SFT_ENT SFT_T(KC_ENT) // Tap for Enter, hold for Shift +#define HPR_TAB ALL_T(KC_TAB) // Tap for Tab, hold for Hyper +#define GUI_SEM GUI_T(KC_SCLN) // Tap for Semicolon, hold for GUI +#define ALT_QUO ALT_T(KC_QUOT) // Tap for Quote, hold for Alt +// Requires KC_TRNS/_______ for the trigger key in the destination layer +#define LT_TC LT(_TOUCHCURSOR, KC_SPC) // L-ayer T-ap T-ouch C-ursor +#define LT_MC(kc) LT(_MOUSECURSOR, kc) // L-ayer T-ap M-ouse C-ursor +#define ALT_TAB M(KC_ALT_TAB) // Macro for Alt-Tab +#define CMD_TAB M(KC_CMD_TAB) // Macro for Cmd-Tab +#define CTL_TAB M(KC_CTL_TAB) // Macro for Ctl-Tab +#define CMD_SLSH M(KC_CMD_SLSH) // Macro for Cmd-Slash (personal shortcut to toggle iTerm2 visibility) +#define AG_FIND M(KC_AG_FIND) // Macros for Cmd-[x] vs Ctrl-[x] based on current AG_NORM or AG_SWAP settings +#define AG_AGAIN M(KC_AG_AGAIN) +#define AG_UNDO M(KC_AG_UNDO) +#define AG_CUT M(KC_AG_CUT) +#define AG_COPY M(KC_AG_COPY) +#define AG_PASTE M(KC_AG_PASTE) +#define AG_D_L M(KC_AG_DESK_L) // For Virtual Desktop Switching: Left, and +#define AG_D_R M(KC_AG_DESK_R) // Right +#define AG_T_C M(KC_AG_TAB_C) // For Chrome, etc. Tab Close, +#define AG_T_N M(KC_AG_TAB_N) // Tab New, and +#define AG_T_R M(KC_AG_TAB_R) // Tab Reopen Closed + +/* Qwerty + * + * ,---------+------+------+------+------+------+------+------+------+------+------+------+------. + * |Hyper/Tab| Q | W | E | R | T | Y | U | I | O | P | Bksp | Bksp | + * |---------`------`------`------`------`------`------`------`------`------`------`------`------| + * | Ctrl/Esc | A | S | MC/D | F | G | H | J | K | L |GUI/; | Alt/" | + * |----------`------`------`------`------`------`------`------`------`------`------`------------| + * | Shift | Z | X | C | V | B | N | M | , | . | / | Sft/Ent | + * |-----------`------`------`------`------`-----'-------`------`------`------`------`-----------| + * | RGUI | Alt | GUI | Lower | TC/Space | TC/Space | Raise | Vol- | Vol+ | Play | + * `-------+-------+-------+-------+---^^^----+---^^^----+---------+--------+--------+----------' + */ + +const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = { +[_QWERTY] = KEYMAP_JD45( +/*,--------+-------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------.*/ + HPR_TAB, KC_Q, KC_W, KC_E, KC_R, KC_T, KC_Y, KC_U, KC_I, KC_O, KC_P, KC_BSPC, KC_BSPC, +/*|--------`-------`--------`--------`--------`--------`--------`--------`--------`--------`--------`--------`--------|*/ + CTL_ESC , KC_A, KC_S,LT_MC(KC_D), KC_F, KC_G, KC_H, KC_J, KC_K, KC_L, GUI_SEM, ALT_QUO , +/*|---------`-------`--------`--------`--------`--------`--------`--------`--------`--------`--------`----------------|*/ + KC_LSFT , KC_Z, KC_X, KC_C, KC_V, KC_B, KC_N, KC_M, KC_COMM, KC_DOT, KC_SLSH, SFT_ENT , +/*|----------`-------`--------`--------`--------`--------`--------`--------`--------`--------`--------`---------------|*/ + KC_RGUI , KC_LALT , KC_LGUI , LOWER , LT_TC , LT_TC , RAISE , KC_VOLD , KC_VOLU , KC_MPLY), +/*`----------+-----------+-----------+-----------+----^^^----+----^^^----+-----------+-----------+-----------+--------'*/ + +/* Colemak + * ,---------+------+------+------+------+------+------+------+------+------+------+------+------. + * |Hyper/Tab| Q | W | F | P | G | J | L | U | Y | ; | Bksp | Bksp | + * |---------`------`------`------`------`------`------`------`------`------`------`------`------| + * | Ctrl/Esc | A | R | MC/S | T | D | H | N | E | I | O | " | + * |----------`------`------`------`------`------`------`------`------`------`------`------------| + * | Shift | Z | X | C | V | B | K | M | , | . | / | Sft/Ent | + * |-----------`------`------`------`------`-----'-------`------`------`------`------`-----------| + * | RGUI | Alt | GUI | Lower | TC/Space | TC/Space | Raise | Vol- | Vol+ | Play | + * `-------+-------+-------+-------+---^^^----+---^^^----+---------+--------+--------+----------' + */ +[_COLEMAK] = KEYMAP_JD45( +/*,--------+-------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------.*/ + HPR_TAB, KC_Q, KC_W, KC_F, KC_P, KC_G, KC_J, KC_L, KC_U, KC_Y, KC_SCLN, KC_BSPC, KC_BSPC, +/*|--------`-------`--------`--------`--------`--------`--------`--------`--------`--------`--------`--------`--------|*/ + CTL_ESC , KC_A, KC_R,LT_MC(KC_S), KC_T, KC_D, KC_H, KC_N, KC_E, KC_I, KC_O, KC_QUOT , +/*|---------`-------`--------`--------`--------`--------`--------`--------`--------`--------`--------`----------------|*/ + KC_LSFT , KC_Z, KC_X, KC_C, KC_V, KC_B, KC_K, KC_M, KC_COMM, KC_DOT, KC_SLSH, SFT_ENT , +/*|----------`-------`--------`--------`--------`--------`--------`--------`--------`--------`--------`---------------|*/ + KC_RGUI , KC_LALT , KC_LGUI , LOWER , LT_TC , LT_TC , RAISE , KC_VOLD , KC_VOLU , KC_MPLY), +/*`----------+-----------+-----------+-----------+----^^^----+----^^^----+-----------+-----------+-----------+--------'*/ + +/* Dvorak + * ,---------+------+------+------+------+------+------+------+------+------+------+------+------. + * |Hyper/Tab| " | , | . | P | Y | F | G | C | R | L | Bksp | Bksp | + * |---------`------`------`------`------`------`------`------`------`------`------`------`------| + * | Ctrl/Esc | A | O | MC/E | U | I | D | H | T | N | S | / | + * |----------`------`------`------`------`------`------`------`------`------`------`------------| + * | Shift | ; | Q | J | K | X | B | M | W | V | Z | Sft/Ent | + * |-----------`------`------`------`------`-----'-------`------`------`------`------`-----------| + * | RGUI | Alt | GUI | Lower | TC/Space | TC/Space | Raise | Vol- | Vol+ | Play | + * `-------+-------+-------+-------+---^^^----+---^^^----+---------+--------+--------+----------' + */ +[_DVORAK] = KEYMAP_JD45( +/*,--------+-------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------.*/ + HPR_TAB,KC_QUOT, KC_COMM, KC_DOT, KC_P, KC_Y, KC_F, KC_G, KC_C, KC_R, KC_L, KC_BSPC, KC_BSPC, +/*|--------`-------`--------`--------`--------`--------`--------`--------`--------`--------`--------`--------`--------|*/ + CTL_ESC , KC_A, KC_O,LT_MC(KC_E), KC_U, KC_I, KC_D, KC_H, KC_T, KC_N, KC_S, KC_SLSH , +/*|---------`-------`--------`--------`--------`--------`--------`--------`--------`--------`--------`----------------|*/ + KC_LSFT , KC_SCLN, KC_Q, KC_J, KC_K, KC_X, KC_B, KC_M, KC_W, KC_V, KC_Z, SFT_ENT , +/*|----------`-------`--------`--------`--------`--------`--------`--------`--------`--------`--------`---------------|*/ + KC_RGUI , KC_LALT , KC_LGUI , LOWER , LT_TC , LT_TC , RAISE , KC_VOLD , KC_VOLU , KC_MPLY), +/*`----------+-----------+-----------+-----------+----^^^----+----^^^----+-----------+-----------+-----------+--------'*/ + +/* Lower + * ,---------+------+------+------+------+------+------+------+------+------+------+------+------. + * | ~ | ! | @ | # | $ | % | ^ | & | * | ( | ) | Bksp | Bksp | + * |---------`------`------`------`------`------`------`------`------`------`------`------`------| + * | [ | F1 | F2 | F3 | F4 | F5 | F6 | _ | + | { | } | "|" | + * |----------`------`------`------`------`------`------`------`------`------`------`------------| + * | ] | F7 | F8 | F9 | F10 | F11 | F12 | - | = | [ | ] | \ | + * |-----------`------`------`------`------`-----'-------`------`------`------`------`-----------| + * | Brite | | | | | | | Prev | Next | Mute | + * `-------+-------+-------+-------+---^^^----+---^^^----+---------+--------+--------+----------' + */ +[_LOWER] = KEYMAP_JD45( +/*,--------+-------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------.*/ + KC_TILD,KC_EXLM, KC_AT, KC_HASH, KC_DLR, KC_PERC, KC_CIRC, KC_AMPR, KC_ASTR, KC_LPRN, KC_RPRN, KC_BSPC, KC_BSPC, +/*|--------`-------`--------`--------`--------`--------`--------`--------`--------`--------`--------`--------`--------|*/ + KC_LBRC , KC_F1, KC_F2, KC_F3, KC_F4, KC_F5, KC_F6, KC_UNDS, KC_PLUS, KC_LCBR, KC_RCBR, KC_PIPE , +/*|---------`-------`--------`--------`--------`--------`--------`--------`--------`--------`--------`----------------|*/ + KC_RBRC , KC_F7, KC_F8, KC_F9, KC_F10, KC_F11, KC_F12, KC_MINS, KC_EQL, KC_LBRC, KC_RBRC, KC_BSLS , +/*|----------`-------`--------`--------`--------`--------`--------`--------`--------`--------`--------`---------------|*/ + BACKLIT , _______, _______, _______, _______ , _______ , _______, KC_MPRV, KC_MNXT, KC_MUTE), +/*`----------+-----------+-----------+-----------+----^^^----+----^^^----+-----------+-----------+-----------+--------'*/ + +/* Raise + * ,---------+------+------+------+------+------+------+------+------+------+------+------+------. + * | 0 | 1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 | 9 | 0 | Bksp | Bksp | + * |---------`------`------`------`------`------`------`------`------`------`------`------`------| + * | $ | 4 | 5 | 6 | . | + | . | 4 | 5 | 6 | * | "|" | + * |----------`------`------`------`------`------`------`------`------`------`------`------------| + * | = | 7 | 8 | 9 | 0 | - | . | 1 | 2 | 3 | / | \ | + * |-----------`------`------`------`------`-----'-------`------`------`------`------`-----------| + * | Brite | | | | | | | Prev | Next | Mute | + * `-------+-------+-------+-------+---^^^----+---^^^----+---------+--------+--------+----------' + */ +[_RAISE] = KEYMAP_JD45( +/*,--------+-------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------.*/ + KC_0 , KC_1, KC_2, KC_3, KC_4, KC_5, KC_6, KC_7, KC_8, KC_9, KC_0, KC_BSPC, KC_BSPC, +/*|--------`-------`--------`--------`--------`--------`--------`--------`--------`--------`--------`--------`--------|*/ + KC_DLR , KC_4, KC_5, KC_6, KC_DOT, KC_PLUS, KC_DOT, KC_4, KC_5, KC_6, KC_ASTR, KC_PIPE , +/*|---------`-------`--------`--------`--------`--------`--------`--------`--------`--------`--------`----------------|*/ + KC_EQL , KC_7, KC_8, KC_9, KC_0, KC_MINS, KC_DOT, KC_1, KC_2, KC_3, KC_SLSH, KC_BSLS , +/*|----------`-------`--------`--------`--------`--------`--------`--------`--------`--------`--------`---------------|*/ + BACKLIT , _______, _______, _______, _______ , _______ , _______, KC_MPRV, KC_MNXT, KC_MUTE), +/*`----------+-----------+-----------+-----------+----^^^----+----^^^----+-----------+-----------+-----------+--------'*/ + +/* TouchCursor layer (http://martin-stone.github.io/touchcursor/) plus personal customizations + * ,---------+------+------+------+------+------+------+------+------+------+------+------+------. + * | AltTab |CmdTab|CtlTab| GUI |Shift | ~ |Insert| Home | Up | End | Bksp | | | + * |---------`------`------`------`------`------`------`------`------`------`------`------`------| + * | | Alt |Space |Tab_C | Find |Again | PgUp | Left | Down |Right |Desk_L| Desk_R | + * |----------`------`------`------`------`------`------`------`------`------`------`------------| + * | | Undo | Cut | Copy |Paste | ` | PgDn | Del |Tab_N |Tab_R |iTerm2| | + * |-----------`------`------`------`------`-----'-------`------`------`------`------`-----------| + * | | | | | | | | | | | + * `-------+-------+-------+-------+---^^^----+---^^^----+---------+--------+--------+----------' + * + * The KC_UNDO, KC_CUT, KC_COPY, KC_PASTE, KC_FIND, and KC_AGAIN keycodes don't + * seem to work on Mac. Presumably they'll work under Windows. + */ + +[_TOUCHCURSOR] = KEYMAP_JD45( +/*,--------+-------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------.*/ + ALT_TAB,CMD_TAB, CTL_TAB, KC_LGUI, KC_LSFT, KC_TILD, KC_INS, KC_HOME, KC_UP, KC_END, KC_BSPC, _______, _______, +/*|--------`-------`--------`--------`--------`--------`--------`--------`--------`--------`--------`--------`--------|*/ + _______ ,KC_LALT, KC_SPC, AG_T_C, AG_FIND,AG_AGAIN, KC_PGUP, KC_LEFT, KC_DOWN, KC_RGHT, AG_D_L, AG_D_R , +/*|---------`-------`--------`--------`--------`--------`--------`--------`--------`--------`--------`----------------|*/ + _______ ,AG_UNDO, AG_CUT, AG_COPY,AG_PASTE, KC_GRV, KC_PGDN, KC_DEL, AG_T_N, AG_T_R,CMD_SLSH, _______ , +/*|----------`-------`--------`--------`--------`--------`--------`--------`--------`--------`--------`---------------|*/ + _______ , _______, _______, _______, _______ , _______ , _______, _______, _______, _______), +/*`----------+-----------+-----------+-----------+----^^^----+----^^^----+-----------+-----------+-----------+--------'*/ + +/* Mouse Layer + * ,---------+------+------+------+------+------+------+------+------+------+------+------+------. + * | | |ACCL0 | | | | |WHL_L | Up |WHL_R | BTN2 | | | + * |---------`------`------`------`------`------`------`------`------`------`------`------`------| + * | |ACCL2 | BTN2 | | BTN1 |ACCL1 |WHL_Up| Left | Down |Right | BTN4 | BTN5 | + * |----------`------`------`------`------`------`------`------`------`------`------`------------| + * | | | | | BTN3 | |WHL_Dn| BTN1 | | | BTN3 | | + * |-----------`------`------`------`------`-----'-------`------`------`------`------`-----------| + * | | | | | | | | | | | + * `-------+-------+-------+-------+---^^^----+---^^^----+---------+--------+--------+----------' + */ + +[_MOUSECURSOR] = KEYMAP_JD45( +/*,--------+-------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------.*/ + _______,_______, KC_ACL0, _______, _______, _______, _______, KC_WH_L, KC_MS_U, KC_WH_R, KC_BTN2, _______, _______, +/*|--------`-------`--------`--------`--------`--------`--------`--------`--------`--------`--------`--------`--------|*/ + _______ ,KC_ACL2, KC_BTN2, _______, KC_BTN1, KC_ACL1, KC_WH_U, KC_MS_L, KC_MS_D, KC_MS_R, KC_BTN4, KC_BTN5 , +/*|---------`-------`--------`--------`--------`--------`--------`--------`--------`--------`--------`----------------|*/ + _______ ,_______, _______, _______, KC_BTN3, _______, KC_WH_D, KC_BTN1, _______, _______, KC_BTN3, _______ , +/*|----------`-------`--------`--------`--------`--------`--------`--------`--------`--------`--------`---------------|*/ + _______ , _______, _______, _______, _______, _______, _______, _______, _______, _______), +/*`----------+-----------+-----------+-----------+----^^^----+----^^^----+-----------+-----------+-----------+--------'*/ + +/* Plover layer (http://opensteno.org) + * ,---------+------+------+------+------+------+------+------+------+------+------+------+------. + * | # | # | # | # | # | # | # | # | # | # | # | # | # | + * |---------`------`------`------`------`------`------`------`------`------`------`------`------| + * | | S | T | P | H | * | * | F | P | L | T | D | + * |----------`------`------`------`------`------`------`------`------`------`------`------------| + * | TogOut | S | K | W | R | * | * | R | B | G | S | Z | + * |-----------`------`------`------`------`-----'-------`------`------`------`------`-----------| + * | Exit | | A | O | | | E | U | | | + * `-------+-------+-------+-------+---^^^----+---^^^----+---------+--------+--------+----------' + */ + +[_PLOVER] = KEYMAP_JD45( +/*,--------+-------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------.*/ + KC_1 , KC_1, KC_1, KC_1, KC_1, KC_1, KC_1, KC_1, KC_1, KC_1, KC_1, KC_1, KC_1 , +/*|--------`-------`--------`--------`--------`--------`--------`--------`--------`--------`--------`--------`--------|*/ + XXXXXXX , KC_Q, KC_W, KC_E, KC_R, KC_T, KC_Y, KC_U, KC_I, KC_O, KC_P, KC_LBRC , +/*|---------`-------`--------`--------`--------`--------`--------`--------`--------`--------`--------`----------------|*/ + XXXXXXX , KC_A, KC_S, KC_D, KC_F, KC_G, KC_H, KC_J, KC_K, KC_L, KC_SCLN, KC_QUOT , +/*|----------`-------`--------`--------`--------`--------`--------`--------`--------`--------`--------`---------------|*/ + EXT_PLV , XXXXXXX, KC_C, KC_V, XXXXXXX , XXXXXXX , KC_N, KC_M, XXXXXXX, XXXXXXX), +/*`----------+-----------+-----------+-----------+----^^^----+----^^^----+-----------+-----------+-----------+--------'*/ + +/* Adjust (Lower + Raise) + * ,---------+------+------+------+------+------+------+------+------+------+------+------+------. + * | | | | | | | | | | | | | Del | + * |---------`------`------`------`------`------`------`------`------`------`------`------`------| + * | | | | | |AGnorm|AGswap|Qwerty|Colemk|Dvorak|Plover| | + * |----------`------`------`------`------`------`------`------`------`------`------`------------| + * | | | | | | | | | | | | | + * |-----------`------`------`------`------`-----'-------`------`------`------`------`-----------| + * | | | | | | | | | | Reset | + * `-------+-------+-------+-------+---^^^----+---^^^----+---------+--------+--------+----------' + */ +[_ADJUST] = KEYMAP_JD45( +/*,--------+-------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------.*/ + _______,_______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, KC_DEL , +/*|--------`-------`--------`--------`--------`--------`--------`--------`--------`--------`--------`--------`--------|*/ + _______ ,_______, _______, _______, _______, AG_NORM, AG_SWAP, QWERTY, COLEMAK, DVORAK, PLOVER, _______ , +/*|---------`-------`--------`--------`--------`--------`--------`--------`--------`--------`--------`----------------|*/ + _______ ,_______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______ , +/*|----------`-------`--------`--------`--------`--------`--------`--------`--------`--------`--------`---------------|*/ + _______ , _______, _______, _______, _______ , _______ , _______, _______, _______, RESET) +/*`----------+-----------+-----------+-----------+----^^^----+----^^^----+-----------+-----------+-----------+--------'*/ +}; + +void persistant_default_layer_set(uint16_t default_layer) { + eeconfig_update_default_layer(default_layer); + default_layer_set(default_layer); +} + +bool process_record_user(uint16_t keycode, keyrecord_t *record) { + switch (keycode) { + case QWERTY: + if (record->event.pressed) { + default_layer_set(1UL<<_QWERTY); + } + return false; + break; + case COLEMAK: + if (record->event.pressed) { + default_layer_set(1UL<<_COLEMAK); + } + return false; + break; + case DVORAK: + if (record->event.pressed) { + default_layer_set(1UL<<_DVORAK); + } + return false; + break; + case LOWER: + if (record->event.pressed) { + layer_on(_LOWER); + update_tri_layer(_LOWER, _RAISE, _ADJUST); + } else { + layer_off(_LOWER); + update_tri_layer(_LOWER, _RAISE, _ADJUST); + } + return false; + break; + case RAISE: + if (record->event.pressed) { + layer_on(_RAISE); + update_tri_layer(_LOWER, _RAISE, _ADJUST); + } else { + layer_off(_RAISE); + update_tri_layer(_LOWER, _RAISE, _ADJUST); + } + return false; + break; + case BACKLIT: + if (record->event.pressed) { + register_code(KC_RSFT); + #ifdef BACKLIGHT_ENABLE + backlight_step(); + #endif + } else { + unregister_code(KC_RSFT); + } + return false; + break; + case PLOVER: + if (record->event.pressed) { + layer_off(_RAISE); + layer_off(_LOWER); + layer_off(_ADJUST); + layer_on(_PLOVER); + if (!eeconfig_is_enabled()) { + eeconfig_init(); + } + keymap_config.raw = eeconfig_read_keymap(); + keymap_config.nkro = 1; + eeconfig_update_keymap(keymap_config.raw); + } + return false; + break; + case EXT_PLV: + if (record->event.pressed) { + layer_off(_PLOVER); + } + return false; + break; + } + return true; +} + +/* + * Macro definition + */ +const macro_t *action_get_macro(keyrecord_t *record, uint8_t id, uint8_t opt) +{ + if (!eeconfig_is_enabled()) { + eeconfig_init(); + } + + bool use_cmd = true; // Use, for example, Cmd-Tab, Cmd-C, Cmd-V, etc. + // Compare to MAGIC_SWAP_ALT_GUI and MAGIC_UNSWAP_ALT_GUI configs, set in: + // quantum/quantum.c + if(keymap_config.swap_lalt_lgui == 1 && keymap_config.swap_ralt_rgui == 1) { + use_cmd = false; // ... or, Alt-Tab, Ctrl-C, Ctrl-V, etc. + } + + switch (id) { + case KC_ALT_TAB: + if(use_cmd) { return (record->event.pressed ? MACRO( D(LALT), D(TAB), END ) : MACRO( U(TAB), END )); } + else { return (record->event.pressed ? MACRO( D(LGUI), D(TAB), END ) : MACRO( U(TAB), END )); } + case KC_CMD_TAB: + if(use_cmd) { return (record->event.pressed ? MACRO( D(LGUI), D(TAB), END ) : MACRO( U(TAB), END )); } + else { return (record->event.pressed ? MACRO( D(LALT), D(TAB), END ) : MACRO( U(TAB), END )); } + + case KC_CTL_TAB: + return (record->event.pressed ? MACRO( D(LCTRL), D(TAB), END ) : MACRO( U(TAB), END )); + case KC_CMD_SLSH: + return (record->event.pressed ? MACRO( D(LGUI), D(SLSH),END ) : MACRO( U(SLSH),END )); + + case KC_AG_FIND: + return use_cmd ? MACRODOWN( D(LGUI), T(F), END ) : MACRODOWN( D(LCTRL), T(F), END ); + case KC_AG_AGAIN: + return use_cmd ? MACRODOWN( D(LGUI), T(G), END ) : MACRODOWN( D(LCTRL), T(G), END ); + case KC_AG_UNDO: + return use_cmd ? MACRODOWN( D(LGUI), T(Z), END ) : MACRODOWN( D(LCTRL), T(Z), END ); + case KC_AG_CUT: + return use_cmd ? MACRODOWN( D(LGUI), T(X), END ) : MACRODOWN( D(LCTRL), T(X), END ); + case KC_AG_COPY: + return use_cmd ? MACRODOWN( D(LGUI), T(C), END ) : MACRODOWN( D(LCTRL), T(C), END ); + case KC_AG_PASTE: + return use_cmd ? MACRODOWN( D(LGUI), T(V), END ) : MACRODOWN( D(LCTRL), T(V), END ); + + case KC_AG_DESK_L: + return use_cmd ? MACRODOWN( D(LGUI), D(LCTRL), T(SCLN), END ) : MACRODOWN( D(LALT), D(LCTRL), T(SCLN), END ); + case KC_AG_DESK_R: + return use_cmd ? MACRODOWN( D(LGUI), D(LCTRL), T(QUOT), END ) : MACRODOWN( D(LALT), D(LCTRL), T(QUOT), END ); + + case KC_AG_TAB_C: + return use_cmd ? MACRODOWN( D(LGUI), T(W), END ) : MACRODOWN( D(LCTRL), T(W), END ); + case KC_AG_TAB_N: + return use_cmd ? MACRODOWN( D(LGUI), T(T), END ) : MACRODOWN( D(LCTRL), T(T), END ); + case KC_AG_TAB_R: + return use_cmd ? MACRODOWN( D(LGUI), D(LSHIFT), T(T), END ) : MACRODOWN( D(LCTRL), D(LSHIFT), T(T), END ); + } + + return MACRO_NONE; +} diff --git a/keyboards/jd45/keymaps/jeebak/readme.md b/keyboards/jd45/keymaps/jeebak/readme.md new file mode 100644 index 0000000000..2e45a46d9b --- /dev/null +++ b/keyboards/jd45/keymaps/jeebak/readme.md @@ -0,0 +1,129 @@ +jeebak's JD45 layout +======================= +NOTE: This is a port of jeebak's planck layout, for jd45. + +This WIP keymap attempts to minimize fingers straying away from the home row. +To aid in this endeavor, when additional modifyer keys to switch layers are +needed, they will be mapped to home row keys. The `keymap.c` file will contain +the exact changes. The diagrams in this README shows the highlights of the +changes from the default mappings. + +I also decided to change all calls to `persistant_default_layer_set()` to +`default_layer_set()` since this is my personal perference. + +## Macros +``` +#define ALT_TAB M(KC_ALT_TAB) +``` + +## Base Layers (Qwerty/Colemak/Dvorak) +These base layers are mostly the same as the default mappings. The interesting +changes are shown below. + +- The `Ctrl/Esc`, will emit an `Escape` when tapped, and act as a `Control` key when held, +- `GUI/;` as `;` and `GUI`, +- `Alt/"` as `"` and `Alt`, +- `Sft/Ent` as `Enter` and `Shift`, and +- `Hyper/Tab` as `Tab` and `Hyper` + +A `TODO` item is to see if it can also act as a `CapsLock` when double-tapped. +The arrow keys, which have been moved to the +[TouchCursor](http://martin-stone.github.io/touchcursor/) layer, have been +replaced with the Media keys as shown. The `MC/kc` key activates the +`MouseCursor` layer when held, and emits the corresponding `kc` for its layer, +when tapped. +``` + ,---------+------+------+------+------+------+------+------+------+------+------+------+------. + |Hyper/Tab| Q | W | E | R | T | Y | U | I | O | P | [ | Bksp | + |---------`------`------`------`------`------`------`------`------`------`------`------`------| + | Ctrl/Esc | A | S | MC/D | F | G | H | J | K | L |GUI/; | Alt/" | + |----------`------`------`------`------`------`------`------`------`------`------`------------| + | Shift | Z | X | C | V | B | N | M | , | . | / | Sft/Ent | + |-----------`------`------`------`------`-----'-------`------`------`------`------`-----------| + | RGUI | Alt | GUI | Lower | TC/Space | TC/Space | Raise | Vol- | Vol+ | Play | + `-------+-------+-------+-------+---^^^----+---^^^----+---------+--------+--------+----------' +``` + +## Lower Layer (Symbols and Function Keys) +The symbols and functions keys are essentially the same as the default mapping. +The most notable changes are that the symbol keys from the `RAISE` layer have +been moved here. The remaining Media keys replace those that are now on the +base layers. The `BACKLIT` key has also been moved here. +``` + ,---------+------+------+------+------+------+------+------+------+------+------+------+------. + | ~ | ! | @ | # | $ | % | ^ | & | * | ( | ) | | Bksp | + |---------`------`------`------`------`------`------`------`------`------`------`------`------| + | [ | F1 | F2 | F3 | F4 | F5 | F6 | _ | + | { | } | "|" | + |----------`------`------`------`------`------`------`------`------`------`------`------------| + | ] | F7 | F8 | F9 | F10 | F11 | F12 | - | = | [ | ] | \ | + |-----------`------`------`------`------`-----'-------`------`------`------`------`-----------| + | Brite | | | | | | | Prev | Next | Mute | + `-------+-------+-------+-------+---^^^----+---^^^----+---------+--------+--------+----------' +``` + +## Raise Layer (Numbers and Arithmetic Operators) +All of the numbers and arithmetic operators are available on this layer. Some +keys are duplicated for the convenience of their positions. The `0` and `$` +keys at the far left are for quick access to beginning and end of line in vim. +``` + ,---------+------+------+------+------+------+------+------+------+------+------+------+------. + | 0 | 1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 | 9 | 0 | | Bksp | + |---------`------`------`------`------`------`------`------`------`------`------`------`------| + | $ | 4 | 5 | 6 | . | + | . | 4 | 5 | 6 | * | "|" | + |----------`------`------`------`------`------`------`------`------`------`------`------------| + | = | 7 | 8 | 9 | 0 | - | . | 1 | 2 | 3 | / | \ | + |-----------`------`------`------`------`-----'-------`------`------`------`------`-----------| + | Brite | | | | | | | Prev | Next | Mute | + `-------+-------+-------+-------+---^^^----+---^^^----+---------+--------+--------+----------' +``` + +## TouchCursor layer plus personal customizations +[TouchCursor](http://martin-stone.github.io/touchcursor/) uses the `Space` key +as the modifier, with the `IJKL` home row keys representing the inverted-T of +the arrow keys. All of the default TouchCursor keymappings for the right hand +are represented below. My personalizations include all of the keys shown for +the left hand. Having the `Alt` and `Shift` keys (as well as the `Control` key +from the base layers) readily accessible from the home row allows quick word +jumps and highlighting when used in conjunction with the arrow keys. The +`Alt-Tab` macro is not only useful under Windows, but also under Mac when used +with alternative switchers like [HyperSwitch](https://bahoom.com/hyperswitch). +The `Cmd-Tab` and `Ctrl-Tab` sequences are duplicated for easy access while in +this layer. The `KC_UNDO, KC_CUT, KC_COPY, KC_PASTE, KC_FIND,` and `KC_AGAIN` +keycodes do not seem to work. There are macros in place that'll "automatically" +choose the correct version (`Cmd-Tab` vs. `Alt-Tab`, `Cmd-C` vs. `Ctrl-C`, +etc.) depending on which layout you've currently selected (`AG_NORM` or +`AG_SWAP`) in the `_ADJUST` layer. The `Desk_L` and `Desk_R` macros are what I +use to switch between Virtual Desktops Left/Right. The `Tab_C`, `Tab_N` and +`Tab_R` are for "Close Tab," "New Tab" and "Reopen Closed Tab" for apps such as +Google Chrome. +``` + ,---------+------+------+------+------+------+------+------+------+------+------+------+------. + | AltTab |CmdTab|CtlTab| GUI |Shift | ~ |Insert| Home | Up | End | Bksp | | | + |---------`------`------`------`------`------`------`------`------`------`------`------`------| + | | Alt |Space |Tab_C | Find |Again | PgUp | Left | Down |Right |Desk_L| Desk_R | + |----------`------`------`------`------`------`------`------`------`------`------`------------| + | | Undo | Cut | Copy |Paste | ` | PgDn | Del |Tab_N |Tab_R |iTerm2| | + |-----------`------`------`------`------`-----'-------`------`------`------`------`-----------| + | | | | | | | | | | | + `-------+-------+-------+-------+---^^^----+---^^^----+---------+--------+--------+----------' +``` + +## Mouse Layer +The Mouse layer, closely mimics the layout/behaviour of the TouchCursor layer. +The `D` key (on QWERTY) is used to activate this layer. All 16 keycodes for the +mouse from the `doc/keycode.txt` file are represented, and logically located, +IMHO. The left and right click buttons are duplicated; on the right hand side, +for a quick click here and there, and again on the left hand side for when the +buttons need to be held for dragging things or highlighting text, thus allowing +the right hand to be free to use the up/down/left/right actions. +``` + ,---------+------+------+------+------+------+------+------+------+------+------+------+------. + | | |ACCL0 | | | | |WHL_L | Up |WHL_R | BTN2 | | | + |---------`------`------`------`------`------`------`------`------`------`------`------`------| + | |ACCL2 | BTN2 | | BTN1 |ACCL1 |WHL_Up| Left | Down |Right | BTN4 | BTN5 | + |----------`------`------`------`------`------`------`------`------`------`------`------------| + | | | | | BTN3 | |WHL_Dn| BTN1 | | | BTN3 | | + |-----------`------`------`------`------`-----'-------`------`------`------`------`-----------| + | | | | | | | | | | | + `-------+-------+-------+-------+---^^^----+---^^^----+---------+--------+--------+----------' +``` diff --git a/keyboards/jd45/rules.mk b/keyboards/jd45/rules.mk new file mode 100644 index 0000000000..2f1e266a14 --- /dev/null +++ b/keyboards/jd45/rules.mk @@ -0,0 +1,67 @@ + + +# MCU name +#MCU = at90usb1287 +MCU = atmega32u4 + +# Processor frequency. +# This will define a symbol, F_CPU, in all source code files equal to the +# processor frequency in Hz. You can then use this symbol in your source code to +# calculate timings. Do NOT tack on a 'UL' at the end, this will be done +# automatically to create a 32-bit value in your source code. +# +# This will be an integer division of F_USB below, as it is sourced by +# F_USB after it has run through any CPU prescalers. Note that this value +# does not *change* the processor frequency - it should merely be updated to +# reflect the processor speed set externally so that the code can use accurate +# software delays. +F_CPU = 16000000 + + +# +# LUFA specific +# +# Target architecture (see library "Board Types" documentation). +ARCH = AVR8 + +# Input clock frequency. +# This will define a symbol, F_USB, in all source code files equal to the +# input clock frequency (before any prescaling is performed) in Hz. This value may +# differ from F_CPU if prescaling is used on the latter, and is required as the +# raw input clock is fed directly to the PLL sections of the AVR for high speed +# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' +# at the end, this will be done automatically to create a 32-bit value in your +# source code. +# +# If no clock division is performed on the input clock inside the AVR (via the +# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. +F_USB = $(F_CPU) + +# Interrupt driven control endpoint task(+60) +OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT + + +# Boot Section Size in *bytes* +# Teensy halfKay 512 +# Teensy++ halfKay 1024 +# Atmel DFU loader 4096 +# LUFA bootloader 4096 +# USBaspLoader 2048 +OPT_DEFS += -DBOOTLOADER_SIZE=4096 + + +# Build Options +# comment out to disable the options. +# +BOOTMAGIC_ENABLE ?= yes # Virtual DIP switch configuration(+1000) +MOUSEKEY_ENABLE ?= yes # Mouse keys(+4700 |