diff options
Diffstat (limited to 'keyboards/jd40')
| -rw-r--r-- | keyboards/jd40/Makefile | 74 | ||||
| -rw-r--r-- | keyboards/jd40/config.h | 79 | ||||
| -rw-r--r-- | keyboards/jd40/jd40.c | 26 | ||||
| -rw-r--r-- | keyboards/jd40/jd40.h | 45 | ||||
| -rw-r--r-- | keyboards/jd40/keymaps/default/keymap.c | 164 | ||||
| -rw-r--r-- | keyboards/jd40/readme.md | 17 |
6 files changed, 405 insertions, 0 deletions
diff --git a/keyboards/jd40/Makefile b/keyboards/jd40/Makefile new file mode 100644 index 0000000000..242748111c --- /dev/null +++ b/keyboards/jd40/Makefile @@ -0,0 +1,74 @@ + + +# MCU name +#MCU = at90usb1287 +MCU = atmega32u4 + +# Processor frequency. +# This will define a symbol, F_CPU, in all source code files equal to the +# processor frequency in Hz. You can then use this symbol in your source code to +# calculate timings. Do NOT tack on a 'UL' at the end, this will be done +# automatically to create a 32-bit value in your source code. +# +# This will be an integer division of F_USB below, as it is sourced by +# F_USB after it has run through any CPU prescalers. Note that this value +# does not *change* the processor frequency - it should merely be updated to +# reflect the processor speed set externally so that the code can use accurate +# software delays. +F_CPU = 16000000 + + +# +# LUFA specific +# +# Target architecture (see library "Board Types" documentation). +ARCH = AVR8 + +# Input clock frequency. +# This will define a symbol, F_USB, in all source code files equal to the +# input clock frequency (before any prescaling is performed) in Hz. This value may +# differ from F_CPU if prescaling is used on the latter, and is required as the +# raw input clock is fed directly to the PLL sections of the AVR for high speed +# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' +# at the end, this will be done automatically to create a 32-bit value in your +# source code. +# +# If no clock division is performed on the input clock inside the AVR (via the +# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. +F_USB = $(F_CPU) + +# Interrupt driven control endpoint task(+60) +OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT + + +# Boot Section Size in *bytes* +# Teensy halfKay 512 +# Teensy++ halfKay 1024 +# Atmel DFU loader 4096 +# LUFA bootloader 4096 +# USBaspLoader 2048 +OPT_DEFS += -DBOOTLOADER_SIZE=4096 + + +# Build Options +# comment out to disable the options. +# +BOOTMAGIC_ENABLE ?= yes # Virtual DIP switch configuration(+1000) +MOUSEKEY_ENABLE ?= yes # Mouse keys(+4700) +EXTRAKEY_ENABLE ?= yes # Audio control and System control(+450) +# CONSOLE_ENABLE ?= yes # Console for debug(+400) +# COMMAND_ENABLE ?= yes # Commands for debug and configuration +KEYBOARD_LOCK_ENABLE ?= yes # Allow locking of keyboard via magic key +# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE +# SLEEP_LED_ENABLE ?= yes # Breathing sleep LED during USB suspend +NKRO_ENABLE ?= yes # USB Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work +# BACKLIGHT_ENABLE ?= yes # Enable keyboard backlight functionality +# MIDI_ENABLE ?= YES # MIDI controls +# UNICODE_ENABLE ?= YES # Unicode +# BLUETOOTH_ENABLE ?= yes # Enable Bluetooth with the Adafruit EZ-Key HID +RGBLIGHT_ENABLE ?= yes # Enable RGB Underglow + +ifndef QUANTUM_DIR + include ../../Makefile +endif + diff --git a/keyboards/jd40/config.h b/keyboards/jd40/config.h new file mode 100644 index 0000000000..e2594f4b37 --- /dev/null +++ b/keyboards/jd40/config.h @@ -0,0 +1,79 @@ +/* +Copyright 2012 Jun Wako <wakojun@gmail.com> + +This program is free software: you can redistribute it and/or modify +it under the terms of the GNU General Public License as published by +the Free Software Foundation, either version 2 of the License, or +(at your option) any later version. + +This program is distributed in the hope that it will be useful, +but WITHOUT ANY WARRANTY; without even the implied warranty of +MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +GNU General Public License for more details. + +You should have received a copy of the GNU General Public License +along with this program. If not, see <http://www.gnu.org/licenses/>. +*/ + +#ifndef CONFIG_H +#define CONFIG_H + +#include "config_common.h" + +/* USB Device descriptor parameter */ +#define VENDOR_ID 0xFEED +#define PRODUCT_ID 0x6060 +#define DEVICE_VER 0x0001 +#define MANUFACTURER geekhack +#define PRODUCT jd40v2 +#define DESCRIPTION t.m.k. keyboard firmware for JD40 MKII + +/* key matrix size */ +#define MATRIX_ROWS 4 +#define MATRIX_COLS 12 + +/* + * Keyboard Matrix Assignments + * + * Change this to how you wired your keyboard + * COLS: AVR pins used for columns, left to right + * ROWS: AVR pins used for rows, top to bottom + * DIODE_DIRECTION: COL2ROW = COL = Anode (+), ROW = Cathode (-, marked on diode) + * ROW2COL = ROW = Anode (+), COL = Cathode (-, marked on diode) + * +*/ +#define MATRIX_ROW_PINS { F0, F1, F5, B4 } +#define MATRIX_COL_PINS { F4, D7, B5, B6, C6, C7, D4, D6, D5, D0, D1, D2 } +#define UNUSED_PINS + +/* COL2ROW or ROW2COL */ +#define DIODE_DIRECTION COL2ROW + +/* Debounce reduces chatter (unintended double-presses) - set 0 if debouncing is not needed */ +#define DEBOUNCING_DELAY 5 + +/* define if matrix has ghost (lacks anti-ghosting diodes) */ +//#define MATRIX_HAS_GHOST + +/* number of backlight levels */ +#define BACKLIGHT_LEVELS 3 + +/* Mechanical locking support. Use KC_LCAP, KC_LNUM or KC_LSCR instead in keymap */ +#define LOCKING_SUPPORT_ENABLE +/* Locking resynchronize hack */ +#define LOCKING_RESYNC_ENABLE + + +/* key combination for magic key command */ +#define IS_COMMAND() ( \ + keyboard_report->mods == (MOD_BIT(KC_LSHIFT) | MOD_BIT(KC_RSHIFT)) \ +) + +#define RGB_DI_PIN D3 +#define RGBLIGHT_TIMER +#define RGBLED_NUM 12 // Number of LEDs +#define RGBLIGHT_HUE_STEP 8 +#define RGBLIGHT_SAT_STEP 8 +#define RGBLIGHT_VAL_STEP 8 + +#endif diff --git a/keyboards/jd40/jd40.c b/keyboards/jd40/jd40.c new file mode 100644 index 0000000000..fa06356d97 --- /dev/null +++ b/keyboards/jd40/jd40.c @@ -0,0 +1,26 @@ +#include "jd40.h" + +void led_set_kb(uint8_t usb_led) { + // put your keyboard LED indicator (ex: Caps Lock LED) toggling code here + + + // if (usb_led & (1<<USB_LED_CAPS_LOCK)) { + // gh60_caps_led_on(); + // } else { + // gh60_caps_led_off(); + // } + + // if (usb_led & (1<<USB_LED_NUM_LOCK)) { + // gh60_esc_led_on(); + // } else { + // gh60_esc_led_off(); + // } + + // if (usb_led & (1<<USB_LED_SCROLL_LOCK)) { + // gh60_fn_led_on(); + // } else { + // gh60_fn_led_off(); + // } + + led_set_user(usb_led); +} diff --git a/keyboards/jd40/jd40.h b/keyboards/jd40/jd40.h new file mode 100644 index 0000000000..77a1222993 --- /dev/null +++ b/keyboards/jd40/jd40.h @@ -0,0 +1,45 @@ +#ifndef JD40_H +#define JD40_H + +#include "quantum.h" +#include "led.h" + +/* GH60 LEDs + * GPIO pads + * 0 F7 WASD LEDs + * 1 F6 ESC LED + * 2 F5 FN LED + * 3 F4 POKER Arrow LEDs + * B2 Capslock LED + * B0 not connected + */ + + /* +inline void gh60_caps_led_on(void) { DDRB |= (1<<2); PORTB &= ~(1<<2); } +inline void gh60_poker_leds_on(void) { DDRF |= (1<<4); PORTF &= ~(1<<4); } +inline void gh60_fn_led_on(void) { DDRF |= (1<<5); PORTF &= ~(1<<5); } +inline void gh60_esc_led_on(void) { DDRF |= (1<<6); PORTF &= ~(1<<6); } +inline void gh60_wasd_leds_on(void) { DDRF |= (1<<7); PORTF &= ~(1<<7); } + +inline void gh60_caps_led_off(void) { DDRB &= ~(1<<2); PORTB &= ~(1<<2); } +inline void gh60_poker_leds_off(void) { DDRF &= ~(1<<4); PORTF &= ~(1<<4); } +inline void gh60_fn_led_off(void) { DDRF &= ~(1<<5); PORTF &= ~(1<<5); } +inline void gh60_esc_led_off(void) { DDRF &= ~(1<<6); PORTF &= ~(1<<6); } +inline void gh60_wasd_leds_off(void) { DDRF &= ~(1<<7); PORTF &= ~(1<<7); } +*/ + +/* JD40 MKII keymap definition macro + */ +#define KEYMAP( \ + K01, K02, K03, K04, K05, K06, K07, K08, K09, K10, K11, K12, \ + K13, K14, K15, K16, K17, K18, K19, K20, K21, K22, K23, \ + K24, K25, K26, K27, K28, K29, K30, K31, K32, K33, K34, \ + K35, K36, K37, K38, K39, K40, K41, K42, K43, K44 \ +) { \ + { KC_##K01, KC_##K02, KC_##K03, KC_##K04, KC_##K05, KC_##K06, KC_##K07, KC_##K08, KC_##K09, KC_##K10, KC_##K11, KC_##K12 }, \ + { KC_##K13, KC_##K14, KC_##K15, KC_##K16, KC_##K17, KC_##K18, KC_##K19, KC_##K20, KC_##K21, KC_##K22, KC_##K23, KC_NO }, \ + { KC_##K24, KC_##K25, KC_##K26, KC_##K27, KC_##K28, KC_##K29, KC_##K30, KC_##K31, KC_##K32, KC_##K33, KC_##K34, KC_NO }, \ + { KC_##K35, KC_##K36, KC_##K37, KC_##K38, KC_##K39, KC_NO, KC_##K40, KC_##K41, KC_##K42, KC_##K43, KC_##K44, KC_NO } \ +} + +#endif diff --git a/keyboards/jd40/keymaps/default/keymap.c b/keyboards/jd40/keymaps/default/keymap.c new file mode 100644 index 0000000000..79ac146c9e --- /dev/null +++ b/keyboards/jd40/keymaps/default/keymap.c @@ -0,0 +1,164 @@ +#include "jd40.h" +#include "action_layer.h" + +#define _BL 0 +#define _AL 1 +#define _FL 2 +#define _UL 3 + +const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = { + [_BL] = KEYMAP( + F12, Q, W, E, R, T, Y, U, I, O, P, BSPC, + TAB, A, S, D, F, G, H, J, K, L, ENT, + LSFT, Z, X, C, V, B, N, M, COMM, UP, DOT, + LCTL, LGUI, LALT, FN0, SPC, SPC, FN0, LEFT, DOWN, RIGHT ), + + [_AL] = KEYMAP( + GRV, F1, F2, F3, F4, F5, F6, F7, F8, F9, F10, DEL, + CAPS, 1, 2, 3, 4, 5, 6, 7, 8, 9, 0, + TRNS, TRNS, TRNS, TRNS, TRNS, TRNS, TRNS, TRNS, SCLN, PGUP, QUOT, + TRNS, TRNS, TRNS, TRNS, FN3, FN3, TRNS, HOME, PGDN, END ), + + [_FL] = KEYMAP( + TRNS, TRNS, TRNS, TRNS, TRNS, TRNS, TRNS, TRNS, TRNS, TRNS, TRNS, TRNS, + TRNS, TRNS, TRNS, TRNS, TRNS, TRNS, TRNS, TRNS, TRNS, TRNS, TRNS, + TRNS, TRNS, TRNS, TRNS, TRNS, TRNS, TRNS, TRNS, TRNS, TRNS, TRNS, + TRNS, TRNS, TRNS, TRNS, TRNS, TRNS, TRNS, TRNS, TRNS, TRNS ), + + [_UL] = KEYMAP( + TRNS, TRNS, TRNS, TRNS, TRNS, TRNS, TRNS, TRNS, TRNS, TRNS, TRNS, TRNS, + TRNS, FN4, FN5, FN11, FN10, TRNS, TRNS, TRNS, TRNS, TRNS, TRNS, + TRNS, TRNS, TRNS, TRNS, TRNS, TRNS, TRNS, TRNS, TRNS, TRNS, TRNS, + TRNS, TRNS, TRNS, TRNS, TRNS, TRNS, TRNS, TRNS, TRNS, TRNS ), +}; + +enum function_id { + RGBLED_TOGGLE, + RGBLED_STEP_MODE, + RGBLED_INCREASE_HUE, + RGBLED_DECREASE_HUE, + RGBLED_INCREASE_SAT, + RGBLED_DECREASE_SAT, + RGBLED_INCREASE_VAL, + RGBLED_DECREASE_VAL, + SHIFT_ESC, +}; + +const uint16_t PROGMEM fn_actions[] = { + [0] = ACTION_LAYER_MOMENTARY(1), // Momentary Fn overlay + [1] = ACTION_LAYER_TOGGLE(2), // Toggle Arrow Layer overlay + [2] = ACTION_LAYER_TAP_KEY(2, KC_CAPS), // Tap to toggle caps lock and hold to activate function layer + [3] = ACTION_LAYER_TOGGLE(3), // Toggle Underglow Layer overlay + [4] = ACTION_FUNCTION(RGBLED_TOGGLE), //Turn on/off underglow + [5] = ACTION_FUNCTION(RGBLED_STEP_MODE), // Change underglow mode + [6] = ACTION_FUNCTION(RGBLED_INCREASE_HUE), + [7] = ACTION_FUNCTION(RGBLED_DECREASE_HUE), + [8] = ACTION_FUNCTION(RGBLED_INCREASE_SAT), + [9] = ACTION_FUNCTION(RGBLED_DECREASE_SAT), + [10] = ACTION_FUNCTION(RGBLED_INCREASE_VAL), + [11] = ACTION_FUNCTION(RGBLED_DECREASE_VAL), + [12] = ACTION_FUNCTION(SHIFT_ESC), +}; + +const macro_t *action_get_macro(keyrecord_t *record, uint8_t id, uint8_t opt) +{ + // MACRODOWN only works in this function + switch(id) { + case 0: + if (record->event.pressed) { + register_code(KC_RSFT); + } else { + unregister_code(KC_RSFT); + } + break; + } + return MACRO_NONE; +}; + +void matrix_scan_user(void) { + +// Layer LED indicators +// ESC led on when in function layer, WASD cluster leds enabled when on arrow cluster + uint32_t layer = layer_state; + if (layer & (1<<1)) { + //gh60_wasd_leds_on(); + } else { + //gh60_wasd_leds_off(); + } + + if (layer & (1<<2)) { + //gh60_esc_led_on(); + } else { + //gh60_esc_led_off(); + } +}; + +#define MODS_CTRL_MASK (MOD_BIT(KC_LSHIFT)|MOD_BIT(KC_RSHIFT)) + +void action_function(keyrecord_t *record, uint8_t id, uint8_t opt) { + switch (id) { + case RGBLED_TOGGLE: + //led operations + if (record->event.pressed) { + rgblight_toggle(); + } + break; + case RGBLED_INCREASE_HUE: + if (record->event.pressed) { + rgblight_increase_hue(); + } + break; + case RGBLED_DECREASE_HUE: + if (record->event.pressed) { + rgblight_decrease_hue(); + } + break; + case RGBLED_INCREASE_SAT: + if (record->event.pressed) { + rgblight_increase_sat(); + } + break; + case RGBLED_DECREASE_SAT: + if (record->event.pressed) { + rgblight_decrease_sat(); + } + break; + case RGBLED_INCREASE_VAL: + if (record->event.pressed) { + rgblight_increase_val(); + } + break; + case RGBLED_DECREASE_VAL: + if (record->event.pressed) { + rgblight_decrease_val(); + } + break; + case RGBLED_STEP_MODE: + if (record->event.pressed) { + rgblight_step(); + } + break; + static uint8_t shift_esc_shift_mask; + // Shift + ESC = ~ + case SHIFT_ESC: + shift_esc_shift_mask = get_mods()&MODS_CTRL_MASK; + if (record->event.pressed) { + if (shift_esc_shift_mask) { + add_key(KC_GRV); + send_keyboard_report(); + } else { + add_key(KC_ESC); + send_keyboard_report(); + } + } else { + if (shift_esc_shift_mask) { + del_key(KC_GRV); + send_keyboard_report(); + } else { + del_key(KC_ESC); + send_keyboard_report(); + } + } + break; + } +}; diff --git a/keyboards/jd40/readme.md b/keyboards/jd40/readme.md new file mode 100644 index 0000000000..7daa0980eb --- /dev/null +++ b/keyboards/jd40/readme.md @@ -0,0 +1,17 @@ +## jd40 mkii keyboard firmware + + Pins: + MATRIX_ROW_PINS { F0, F1, F5, B4 } + MATRIX_COL_PINS { F4, D7, B5, B6, C6, C7, D4, D6, D5, D0, D1, D2 } + RGB_DI_PIN D3 + +====================== + +## Quantum MK Firmware + +For the full Quantum feature list, see [the parent readme.md](/readme.md). + +## Building + +Download or clone the whole firmware and navigate to the keyboards/jd40 folder. +Once your dev env is setup, you'll be able to type `make` to generate your .hex - you can then use the Amtel Flip to program your .hex file. |