diff options
Diffstat (limited to 'keyboards/iris/rules.mk')
| -rw-r--r-- | keyboards/iris/rules.mk | 46 |
1 files changed, 13 insertions, 33 deletions
diff --git a/keyboards/iris/rules.mk b/keyboards/iris/rules.mk index fa261adc6f..69bc62f876 100644 --- a/keyboards/iris/rules.mk +++ b/keyboards/iris/rules.mk @@ -1,43 +1,17 @@ -# MCU name MCU = atmega32u4 - -# Processor frequency. -# This will define a symbol, F_CPU, in all source code files equal to the -# processor frequency in Hz. You can then use this symbol in your source code to -# calculate timings. Do NOT tack on a 'UL' at the end, this will be done -# automatically to create a 32-bit value in your source code. -# -# This will be an integer division of F_USB below, as it is sourced by -# F_USB after it has run through any CPU prescalers. Note that this value -# does not *change* the processor frequency - it should merely be updated to -# reflect the processor speed set externally so that the code can use accurate -# software delays. F_CPU = 16000000 - -# -# LUFA specific -# -# Target architecture (see library "Board Types" documentation). ARCH = AVR8 - -# Input clock frequency. -# This will define a symbol, F_USB, in all source code files equal to the -# input clock frequency (before any prescaling is performed) in Hz. This value may -# differ from F_CPU if prescaling is used on the latter, and is required as the -# raw input clock is fed directly to the PLL sections of the AVR for high speed -# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' -# at the end, this will be done automatically to create a 32-bit value in your -# source code. -# -# If no clock division is performed on the input clock inside the AVR (via the -# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. F_USB = $(F_CPU) # Bootloader # This definition is optional, and if your keyboard supports multiple bootloaders of # different sizes, comment this out, and the correct address will be loaded # automatically (+60). See bootloader.mk for all options. -BOOTLOADER = caterina +ifeq ($(strip $(KEYBOARD)), iris/rev3) + BOOTLOADER = dfu +else + BOOTLOADER = caterina +endif # Interrupt driven control endpoint task(+60) OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT @@ -46,8 +20,9 @@ OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT # change to "no" to disable the options, or define them in the Makefile in # the appropriate keymap folder that will get included automatically # + BOOTMAGIC_ENABLE = no # Virtual DIP switch configuration(+1000) -MOUSEKEY_ENABLE = yes # Mouse keys(+4700) +MOUSEKEY_ENABLE = no # Mouse keys(+4700) EXTRAKEY_ENABLE = yes # Audio control and System control(+450) CONSOLE_ENABLE = no # Console for debug(+400) COMMAND_ENABLE = yes # Commands for debug and configuration @@ -57,10 +32,15 @@ MIDI_ENABLE = no # MIDI controls AUDIO_ENABLE = no # Audio output on port C6 UNICODE_ENABLE = no # Unicode BLUETOOTH_ENABLE = no # Enable Bluetooth with the Adafruit EZ-Key HID -RGBLIGHT_ENABLE = yes # Enable WS2812 RGB underlight. Do not enable this with audio at the same time. +RGBLIGHT_ENABLE = yes # Enable WS2812 RGB underlight. # Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE SLEEP_LED_ENABLE = no # Breathing sleep LED during USB suspend SPLIT_KEYBOARD = yes DEFAULT_FOLDER = iris/rev2 + +# VIA Support - Comment these 3 lines out to disable +RAW_ENABLE = yes +DYNAMIC_KEYMAP_ENABLE = yes +SRC += keyboards/wilba_tech/wt_main.c |